Warranty/Shipping - Sports Attack · If you turn off your e-Hack Attack or if your e-Hack Attack...
Transcript of Warranty/Shipping - Sports Attack · If you turn off your e-Hack Attack or if your e-Hack Attack...
INSTRUCTION MANUAL
ELECTRONIC BASEBALL PITChINg MAChINE
REV
083
115
SPORTS ATTACK LLC800-717-4251www.sportsattack.com
Includes: OPERATION · SETUP · USE & CARE · SERVICE
Patent No.: US 8,001,954 B2
BA
SE
BA
LL
BA
SE
BA
LL
2e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
ShIPPINg DAMAgE CLAIMS PROCEDURENOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory.
Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED: 1. VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt, and that the note of loss or damage is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY: Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: If damage is unnoticed until the merchandise is unpacked, notify the transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them. This must be done within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.
Sports Attack LLC. cannot assume liability for damage or loss incurred in transit. We will, however, at your request, supply you with the necessary documents to support your claim.
Warranty/S
hipping
RetuRnsTo return an item, please contact our Customer Service Department at 800-717-4251.
A 15% restocking fee will be charged for any items accepted for return. It is the customer’s responsibility to handle the repacking and shipment (as well as all associated fees) back to Sports Attack.
No returns will be accepted after 30 days of receiving product.
WARRANTY STATEMENTWhat is most important to Sports Attack is that your machine meets your expectations of quality and performance. We stand behind the material and workmanship of our machines for five (5) years from the date or original purchase for institutional and residential use and one (1) year for commercial environments, with the following exceptions:
-Throwing Wheels are warranted for two (2) years;
-Electronic Controller is warranted for two (2) years; and,
-Throwing Wheel Motors are warranted for two (2) years.
This warranty excludes any cosmetic issues or normal wear and tear of the unit, and is not in effect if the machine has been misused, misapplied, improperly assembled, or modified with-out the express written permission of Sports Attack. In addition, this warranty does not apply to damage in transit, in any accident unrelated to the direct operation of the equipment, or by fire, flood or act of God.
If you encounter any issues during the warranty period, Sports Attack will quickly get your machine back in working order. If the warranty repair involves a replacement part, we will make sure you get both the part and easy instructions for replacement at no cost to you. If a service person is needed, Sports Attack will pay the pre-approved labor charge to get your machine back in working order.
Please know that any problem can quickly be resolved with a phone call to our experienced, responsive customer service department at 800.717.4251. We are here to answer your ques-tions and to make sure your machine provides you years of service.
RETURNSSports Attack manufactures the highest quality sports training equipment in the world. If for any reason you are not satisfied, a machine can be returned within 30 days of receipt for any reason for a full refund less a 10% restocking fee. Cost of shipping the unit back to Sports At-tack will also be the responsibility of the purchaser. Please note that the refund amount may be reduced by any non-cosmetic damage to the machine.
If you have any questions or concerns, please give our experienced, responsive customer service department a call at 800.717.4251.
to register the Warranty, please go to our website:
www.sportsattack.com/warranty
For repairs and service after the Warranty period, please call:
Sports Attack Customer Service Dept.Ph 800-71 7-4251Fx 775-345-2883
3e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Ball Use With Sports Attack Pitching Machines
Dimpled Pitching Machine Balls: Sports Attack’s dimpled pitching machine balls are designed to deliver a consistent pitch and out last any other type of ball. These balls have a realistic feel off the bat. They are soft enough not to dent aluminum bats and greatly reduce the chances of any build-up on throwing wheels. Sports Attack has a full line of pitching machine balls to cover every need for indoor or outdoor use. Leather Pitching Machine Balls with Low-Profile (Kevlar) Seams: Sports Attack’s leather pitching machine balls with low-profile seams will hit like a real ball but will wear well with machine use due to the low profile, Kevlar-reinforced seams. These long-lasting leather balls are designed specifically for pitching machine (wheel) use only and for those wanting that more realistic look and feel of a baseball. Sports Attack has a full line of pitching machine balls to cover every need for indoor or outdoor use. Regulation “Real Leather” Balls: Hitters, especially at upper levels, prefer to hit regulation “real leather” balls. The use of these real leather balls will have little or no material transfer and rarely require wheel cleaning. DO NOT USE SYNTHETIC LEATHER BALLS Synthetic leather balls should not be used in pitching machines. They will leave a buildup on the throwing surfaces affecting pitching machine accuracy. If your throwing wheels have this build-up, please reference the machine manual for cleaning instructions and clean wheels prior to further use. Call Sports Attack for more information 775-345-2882. Ball Consistency: For the highest level of accuracy, balls used in your pitching machine should be of the same type, wear and manufacturer. A pitching machine will only be as consistent as the balls being used:
• Never mix worn “old” balls with new balls • Do not mix different brands of balls • Do not mix different types of balls • When using a seamed ball, feed the ball into the machine with the seams in the same
general position each time • Wet or damp balls tend to slip on the throwing surfaces. Towel dry any ball that has
moisture on it before using in a pitching machine. • Extreme cold can cause balls to become harder than normal. This could cause the balls to
pitch slower and / or inconsistently. • Use dimpled pitching machine balls or regulation leather balls only. Do not use Synthetic
Leather balls.
4e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
CAutIOnPeRsOnAL InJuRY HAZARD
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
•
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
See electrical requirements
•
Do not operate on wet ground or in wet conditions.
IMPORTANT SAFETY INSTRUCTIONSELECTRICAL REQUIREMENTSUse a standard 115 volt, 20 amp single phase 3-wire grounded power source.
EXTENSION CORD USEUp to 50 feet from power source, use a minimum #14/3 grounded 3-wire.
50 to 100 feet from power source, use a minimum #12/3 grounded 3-wire.
Over 100 feet from power source, consult a licensed electrician for required power cord size.
GeneRAtOR useDO NOT use the eHack with any generator. Generator use can cause damage and system failure.
sAFetY InstRuCtIOns If you turn off your e-Hack Attack or if your e-Hack Attack gets unplugged,
WAIT 20 SECONDS BEFORE POWERING UP YOUR E-HACK ATTACK.
Failure to do so can lead to garbled/unreadable screen displays.
USE & OPERATION
Machine set uPstep 1
turning Power OnTurn the on/off switch to “on”. The software will load, this takes about 10-15 seconds. After software has loaded the machine setup will appear. Be sure machine is on level surface and at proper distance fromHome plate. Center machinewith home plate.
step 2
starting MachineStarting machine Press Start, there will be a short delay as themotors come up to speed.
Press Start
5e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
step 3Warning -You will see warning displayedon screen
step 4Machine set up -Ready for BallsMachine requires you to throw a minimum of 2 test pitches toalign the pitch to throw over the center of Home plate. Toadjust inside-outside, slide rearleg left or right as needed. Repeat until ball crosses the center of Home plate
step 5Accept AlignmentOnce you have thrown at least 2 test pitches and have the ball crossing the center of the Home plate, press “Accept Alignment”.Once pressed screen will go to the Main Menu
Main Menu OverviewThis is the main menu screen. From here you can navigate to all the e-Hack’s features
step 6
Main MenuThis is the main menu screen, from here you can navigate to all the e-Hacks features. After reviewing main menu proceed to Step 7.
step 7
Customizing PitchesTo begin customizing pitches,press “Pitch Type”
Press “Accept Alignment”
Press “Pitch Type”
Use & Operation- Machine Setup Continued
6e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Main Menu Overview
Legend
M1 = Motor 1 (top left motor) Hz = Horizontal
M2 = Motor 2 (center motor) Vt = Vertical
M3 = Motor 3 (top right motor)
eHack Default Pitch settingsFollowing are the factory default pitch settings. Use this chart to assist i modifying (adjusting) default pitches in steps 6, 7 and 8.
These are the Sports Attack’s default pitch settings. These pitches are common settings used for upper level baseball. Default pitch settings are programmed as a starting point for you to begin customizing your desired pitch speed, ball spin and location.
Custom 1- Custom 5All these pitch defaults are fastballs at different speeds.
Important Safety Instructions &
Hom
e Screen
WARnInGPeRsOnAL InJuRY HAZARD
Carefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
eHack Baseball -‐ SoftballDefault Pitch Settings
4/7/15files:Engineering:Systems_Products:eHack:eHack Software:eHack_Default_Pitch_Settings.xlsx
M1 M2 M3 Hz Vt
57 91 57 500 200
41 75 41 500 280
59 24 89 579 420
55 41 89 635 400
75 31 75 500 400
61 96 61 500 195
56 91 56 500 200
51 86 51 500 200
46 81 46 500 350
41 76 41 500 350
M1 M2 M3 Hz Vt
56 90 56 500 200
40 75 40 500 280
90 25 60 420 420
90 41 54 365 400
74 32 74 500 400
60 95 60 500 195
55 90 55 500 200
50 85 50 500 200
45 80 45 500 270
40 75 40 500 350
Slider
BaseballRH DefaultsFastballChange UpCurveball
Curveball
SplitfingerCustom-‐1Custom-‐2Custom-‐3Custom-‐4Custom-‐5
BaseballLH DefaultsFastballChange Up
SliderSplitfingerCustom-‐1Custom-‐2Custom-‐3Custom-‐4Custom-‐5
81
MPH (+/-‐5)
81
64
67
72
70
84
72
69
63
55
Estimated Speed
Estimated Speed
MPH (+/-‐5)
69
63
55
64
67
72
70
84
72
Right Handed Defaults
eHack Baseball -‐ SoftballDefault Pitch Settings
4/7/15files:Engineering:Systems_Products:eHack:eHack Software:eHack_Default_Pitch_Settings.xlsx
M1 M2 M3 Hz Vt
57 91 57 500 200
41 75 41 500 280
59 24 89 579 420
55 41 89 635 400
75 31 75 500 400
61 96 61 500 195
56 91 56 500 200
51 86 51 500 200
46 81 46 500 350
41 76 41 500 350
M1 M2 M3 Hz Vt
56 90 56 500 200
40 75 40 500 280
90 25 60 420 420
90 41 54 365 400
74 32 74 500 400
60 95 60 500 195
55 90 55 500 200
50 85 50 500 200
45 80 45 500 270
40 75 40 500 350
Slider
BaseballRH DefaultsFastballChange UpCurveball
Curveball
SplitfingerCustom-‐1Custom-‐2Custom-‐3Custom-‐4Custom-‐5
BaseballLH DefaultsFastballChange Up
SliderSplitfingerCustom-‐1Custom-‐2Custom-‐3Custom-‐4Custom-‐5
81
MPH (+/-‐5)
81
64
67
72
70
84
72
69
63
55
Estimated Speed
Estimated Speed
MPH (+/-‐5)
69
63
55
64
67
72
70
84
72
Left Handed Defaults
7e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
Pitch type Main Menu Overview
Button Functions
1 - Play - starts the Machine
2 -stop - stops the Machine
3 - Back - Goes to previous screen (one screen at a time)
4 - Modify - Allows you to change pitch settings
5 - LH/RH - switch between Right-handed and Left-handed pitches
6 & 7 - Arrows allow you to toggle through the 10 default pitches
step 8
Customizing default pitchesThe pitch type main menu automatically brings you toRight-handed fastball.
A. Press play to start. This allows you to throw balls as you customize your pitches
* Anytime a setting is blinking the machine is NOT ready yet. WAIT until blinking stops. Once blinking stops, you may proceed.B. Throw some balls to see the current default speed and location
C. Press modify to begin adjusting the pitch speed, location and ball spin
step 9
Motors settingsOnce “Modify” button is selected, M1* (top left corner)will get highlighted. Using up and down arrow buttons speed can be adjusted. When correct required speed is selected, click next button to move to the next motor. Once speed of all motors is established you can continue to adjust horizontal (HZ) and vertical (VT)
*M1, M2, M3 are motors; thosemarks correspond with cast imprints on the machine
1
2
3 4 5
6
7
Select “Modify”
Speed adjusting arrow buttons“Next” Button
8e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
step 10
Customizing Pitches- Bottom right button allowsyou to choose between right handed and left handed pitch
- Top right button will allowto pitch a ball.
- Select Modify to adjust thespeed of motors.
step 12
savingAdjustments that haven been made can be saved. Click the“Save” button and “Saving ...”will appear. Once it disappears settings are saved.
step 13
next Pitch- Use arrows to move to the nextpitch type.
Pitches available:FastballChangeCurveSliderSplitCustom 1 thru 5
Select “Save”
Select “Modify”
Appears on screen while saving new settings
Click to move to another pitch“Back” Button
9e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
step 14
sequencesAfter you set your pitchesyou can set your sequences.Click on the back button to getto the main screen. Than you click on the Pitch Seq buttonto create sequences.
step 15
Creating sequencesOnce in the sequence screenyou can create up to 10 differentsequences for left and 10 different. sequences for right
step 16
Creating sequences cont’dTo switch between left and rightsequences click LH/RH button.
To create sequence, click theload button.
“Pitch Seq” Button
“LH/RH” Button Select “Load”
10e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
step 17
Creating sequences cont’dAfter you click create a sequencenew screen will appear, wherepitches can be selected.
Arrow buttons will help you select the pitch and the numberof the same pitch in the sequence.
Next button moves you from field to field to be able to customize it.
step 18
Creating sequences cont’dYou can see an example of seguence on the screen. Sequence can have up to 10 pitches and they each pitch canbe thrown up to 10 times.
step 19
Creating sequences cont’d
Vertical OffsetUsing the “next” button you canget a little square next to each pitch. If you want have a vertical offset on a certain pitch, it can be created with the help of “arrow” buttons. Once you have created a vertical offset asterisk will appear next tot he pitch.
“Next” Button“Arrow” Buttons
Vertical OffsetVertical Offset Indicator
11e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
step 20
saving sequenceOnce you are done setting upthe sequence, click the “save:button.
If changes need to be done to thesequence you can edit from theSequence home screen.
step 21
Random sequence RunIn a sequence you have theoption to select “RAND”- to randomize the pitcheswithin the sequence
Repeat - to repeat sequenceclick repeat.
step 22
Manual ModeGo back to home screen andselect Manual Mode.
“Save” Button
“Manual Mode” Button
“Repeat” Button
12e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
step 23
Manual Mode cont’dUsing button next to each pitchselect a pitch. Wheels will startrunning and you can pitch a ball.Yo can select left and right with the “LH/RH” button. You can also modify each pitch by clicking on“modify” button.
step 24
Modify in Manual ModeOnce in modifying mode, you can adjust speed of the motorsby selecting Faster / Slower.
Speed will adjust in proportion.
step 25
Pitch CountManual mode offers ball countfeature. It will show you howmany pitches were pitched on the particular setting.
The count will disappear once you leave the screen, select a different pitch or modify a pitch.
“Faster & Slower” Buttons
Pitch Count
“Modify” Button “LH/RH” Button
Select Pitch
13e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
step 26
ResetAnytime you need to rest tomanufacture settings or eraseall your sequences you need togo to the Utility Screen.
To get there go to the home screen and select utility.
step 27
Reset - utilityOnce in the “Utility” screen.You have two options. You can load default pitch-types
Lifetime CountersFrom the Utility Screen you canget to the Life-time CountersScreen by Clicking the “Centers” Button. This screen will showcount of all pitches pitched on the e-Hack Attack Machine.
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
Utility Options “Centers” Button
“Utility” Button
14e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
step 28
Buzzer FunctionThe Buzzer, when turned on willemit a brief sound each timethe machine is ready to acceptanother ball. When activated, itlets the operator know that the machine is ready withouthaving to look a the screen.
Anytime you want to turn off buzzer or set the buzzer volume go to the Utility Screen.
To get there go to the home screen and select utility.
Buzzer ControlOnce in the “Utility” screen.You select “Config” Button.
Buzzer set upOnce in the Configuration screen. Keep clicking “Bzzr” button until you desired selection will appear onthe screen.
Options available:Bzzr lowBzzr medBzzr hiBzzr off
Important Safety Instructions &
Hom
e ScreenWARnInG
PeRsOnAL InJuRY HAZARDCarefully read all instructions in this manual, and all labels and warnings on e-Hack Attack before using this machine.
Use machine only under adult supervision. Failure to operate e-Hack Attack as described in this manual can result in severe personal injury or death.
eLeCtRICAL sHOCK HAZARDe-Hack Attack must be connected to a properly grounded electrical receptacle.
•
Do not operate on wet ground.
CAutIOnPeRsOnAL InJuRY HAZARD
DO NOT allow anyone to walk in front of the machine if it is connected to electrical power.
•
Carefully check the e-Hack Attack for completeness and condition before connecting to electrical power.
•
At all times when the e-Hack Attack is “ON” it is possible a ball will be pitched. Be alert.
eQuIPMent eLeCtRICAL DAMAGe
DO NOT plug in or energize this equipment until this manual is read and followed.
Utility Options
“Utility” Button
“BZZR” Button
15e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
CARE, CLEANINg & MAINTENANCE
tHROWInG WHeeL MOtORs Motors are sealed and require no lubrication.
Check bolts for tightness once a season. Tighten bolts securely, but do not over-tighten.
CLeAnInG tHe tHROWInG WHeeLsThe throwing wheels must be kept clean to maintain accuracy. Clean the wheels periodically to control the build-up of grass and dirt.
1. Turn the on/off switch “OFF” and allow the wheels to come to a complete stop. Unplug Junior Hack Attack from electric power.
2. Dampen a rag with soap and water. Turn the throwing wheel by hand and scrub the wheel until the build-up is removed. For very heavy build-up, a synthetic scouring pad, such as a Scotch-Brite® scouring pad, may be used sparingly. Acetone may be required to help loosen the build-up of dirt or ball residue.
eXAMIne tHe MACHIneExamine e-Hack Attack for condition and completeness before every use:
1. For batting practice, be sure the horizontal swivel lock is secured.
2. Throwing wheels must be tight on the motor shafts. Check that the keyway retaining bolts are tight.
3. Wheel guard and ball chute must be securely fastened to the throwing head.
Check Motor Brush wear:
Each motor has a set of 2 motor brushes. When the brushes approach 1/4 inch in length it is time to replace the brushes.
ShUTTINg DOWN
tuRnInG e-HACK AttACK “OFF” 1. Turn the on/off switch “OFF”.
2. Unplug e-Hack Attack from the power source.
PuttInG e-HACK AttACK AWAY (team lift - requires 2 persons) 1. Be absolutely sure that the throwing wheels have completely stopped turning.
2. Using the rear leg as a handle, tip Hack Attack up and over onto the wheel guard.
3. Remove (unsocket) both front legs and store by inserting in the travel storage sockets.
4. See Figure 8 at right: Again, using the rear leg as a handle, tip e-Hack Attack back until machine can be comfortably rolled on the travel wheels. e-Hack Attack can now be rolled and maneuvered off of the field.
5. To prevent damage in transport, rest the throwing head on the wheel guard and yoke; motors should be down, and the control panel pointing up.
CAutIOn PeRsOnAL InJuRY HAZARD
Never attempt to clean the throwing wheels while they are turning. Rags or implements caught in spinning wheels can cause serious injury.
Unplug the machine before cleaning the wheels or performing any service.
CHeMICAL HAZARDMethyl Ethyl Ketone (M.E.K) Read and follow the directions and safety instructions on the M.E.K container.
FIRe HAZARDMethyl Ethyl Ketone (M.E.K) M.E.K. is flammable. Do not use M.E.K. around a fire or flame. Do not use M.E.K. near a running generator or other source of ignition.
Care, Cleaning & M
aintenance
Storing front legs in travel socket
Maneuvering
16e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
EXPLODED VIEWExploded View
1 Cane Tip
2 Leg - Standard Size (ea.)
5 Undercarriage
17 Snap-Button
19 Travel Wheel (with bolt, nut, washers)
21 Yoke
34 Main Casting, Throwing Head
35 Clamp, Cable
37 Motor, Variable Speed e-Hack
38 Throwing Wheel
39 Ball Chute
43 Wheel Guard (ea.)
63 e-Hack Electronic Box
64 Safety Resets (Circuit Breakers)
65 On/Off Switch
Power Cord (not shown)
1
2
5
21
31
37
37
37
38
38
34
35
39
38
2
17
2
19
43
19
64
65
17e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Parts ListPARTS LIST (e-hack Baseball)
Parts List
To order additional parts, please call:
Sports Attack Customer Service DepartmentPh 800-717-4251Fx 775-345-2883
REF#sHA BASEBALL
PART#sDESCRIPTION
39 520-0004 Ball Chute
1 280-1005 Heavy Duty Cane Tip, set of 3
35 Clamp, Cable
63 530-0006 Controller Assembly
17 270-0002 Snap-Button
2 532-0001 Leg, Standard Size ea.
37 530-0003 Motor, Variable Speed e-Hack
65 223-0004 On/Off Switch (Rocker)
old 223-0002 On/Off Switch (Old Style - Toggle)
232-0000 Power Cord (US)
64 232-0002 Safety Resets (Circuit Breakers)
38 531-0001 Throwing Wheel
19 281-0001 Travel Wheel, Extra-Heavy Duty
5 520-0003 Undercarriage
43 520-0021 Wheel Guard ea.
21 520-0003 Yoke
34 350-0010 Main Casting, Throwing Head
18e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Please visit our web site www.sportsattack.com for information about Sports Attack sports training products, or call 800-717-4251 for complete information and specifications.
SPORTS ATTACK PRODUCTS
BAseBALL
Hack attack BaseBall Junior Hack attack BaseBall
sOCCeR CRICKet
strike attack crick attack
19e-Hack attack baseball pitcHing macHine
sports attack, llc. • 800-717-4251 • sportsattack.com
Please visit our web site www.sportsattack.com for information about Sports Attack sports training products, or call 800-717-4251 for complete information and specifications.
SPORTS ATTACK PRODUCTS
tennIs FOOtBALL
ace attack snap attack
attack (shown with optional ball bags) skill attack
VOLLeYBALL
attack ii (shown with optional ball bags)