wapa-brasil.com.brwapa-brasil.com.br/.../uploads/2015/10/MANUAL-NVR.docx · Web viewNetwork Video...

Network Video RecorderUSER MANUAL

v1.0.3

Contents

Chapter1 Introduction ��

�� 11�1 Start Up and Shut down the NVR �� 1

1�2 The Main Menu �� 1

1�3 Playback�� 2

Chapter2 Parameters Configuration �� 4

2�1 Channel Management �� 4

2�1�1 Channel Config �� 4

2�1�2 Image Config �� 5

2�1�3 PTZ Config �� 6

2�1�4 Motion Detection �� 7

2�1�5 Camera Config �� 7

2�2 Scheduled Record �� 8

2�3 Disk Management�� 9

2�4 File Management �� 10

2�5 System Maintain �� 10

2�6 System Configuration �� 11

2�6�1 General�� 11

2�6�2 Network �� 11

2�6�3 Preview�� 13

2�6�4 User �� 13

2�6�5 System Running �� 14

※ Warning • Change s or modific ations not e xpr e ssly appr ov e

d by the manufacturer could void the user's authority to operate theequipment�

• These servicing instructions are for use by qualified service personnel only�

-1

Chapter1 Introduction1.1 Start Up and Shut down the NVR1� Start up the NVRAfter successfully starting up the NVR, right click the main interface, it comes the the menu, click Unlock to unlock the system, and login� By default, username andpassword of administrator are admin�

2� Shut down the NVRRight click the main interface to get the menu out� Click Shut down and Shut down the NVR� After shutting down, please cut off power supply�

1.2 The Main MenuThe main interface is shown as following� Right click the main interface, Click�

-2

Name Description

Channel Management Manage IP Cameras: adding,modifing, and configuration of PTZ, motion detection

Record Schedule Set recording modeDisk Management Harddisk initialization and configurationFile Management Copy ImagesPlayback Playback the record filesSystem Maintain View logs and update systemSystem Configuration Configuration of alarm, network,user information,

etc�Shut down Logoff, shutdown and restart the system

1.3 PlaybackClick Playback button on the main interface to enter the playback interface�

•Select DateClick to select date of record to playback� Dates marked in color means there is record(file) on the day�•Playback coordinateThe abscissa represents the time, and the ordinate the channel of camera� Choose the channel that you want to playback by checking the corresponding channel number�Note: It Supports 4-ch synchronous realtime playback.•Recording Progress barGreen bar means continuous record, red bar means motion record�•Play/Stop, Single frame play•Play SpeedIt supports 1/2，1/4，2，4 times of normal speed.•Time positioned play

-3

Enter the exact time and click to playback�•Video download1�Click to access video download window;2�Choose the camera you want to backup;3�Enter start time and end time of the record;4�Choose the path and click download�

Notes:Each Disk can save 4 record file which must be less than 1G, and 120 photos� System will overwrite when exceeding limit�

-4

Chapter2 Parameters Configuration2.1 Channel Management2.1.1 Channel ConfigClick Channel Management , enter into Channel Config as shown�

• SearchClick to search cameras which will be listed on the leftside box�

• Search&addSearch and add cameras with one click�

• Set IPDouble click the camera on the left list� It comes Modify IP Channel dialog, modifyIP and click OK�

• AddSelect the camera on the left list and then Add the camera to the NVR host�

• Channel NameDouble click the camera on the right list and input new name for camera�

• ViewCheck the box, the video will be shown on the main interface�

• up/downSelect the camera, click up/down to adjust it's order�

• DeleteSelect the camera on the right list, click to delete it�

-5

2.1.2 Image ConfigClick Channel Management on the main menu, enter into Image Config as shown�

•ChannelSelect the camera you want to configure�

•White BalanceThere are auto,outdoor, fluorescence, manual, indoor, tungsten wire for option�

•Expose modeDrag the bar to adjust the expose intensity and sensitivity�

•Set ColorDrag the Red/Blue bar to adjust the image color� The white balance mode should be Manual before adjusting�

•Enhance ImageStrengthen the image edges to increase the image quality when turning it on�

•Stream rateThere are Low, Medium, High, Default for option�

•Digital shutterThere are 8 levels for option� By default, it is 1/25s� You can choose 1/100s to avoid shadow when there is high-speed movement� If the video is too dark when it is1/100s , you can change to 1/50s to increase the brightness�

•Frame rateChange frame rate, there are 4 levels for option�•IR switchSwitch according to the brightness of Image�

•Rotate 180°

-6

Rotate the image 180° �•Detect Light Leak

2.1.3 PTZ ConfigClick Channel Management on the main menu, enter into PTZ Config as shown�

•PTZ ControlClick Up,Down,Left and right arrows to control PTZ rotating�

•PAN/TILT SpeedAdjust pan and tilt speed�

•Preset Set presets of Speed Dome Camera�1�Setting stepsSelect a camera, adjust its location, focus and zoom , enter the preset ID and preset name, and then click Add to save the preset� After successfully added, thepreset ID and preset name will display in the blank area� You can repeat the steps to add more presets�2� Presets UsingAfter adding presets,click Start Cruising ,and the dome will rotate among presets�

• Interval(s)The time in seconds to stay on a preset�

• AddFill in preset ID, preset name, then click Add to make them valid�

• DeleteChoose one preset, click Delete to delete it�• Auto ScanCheck the box, the speed dome will scan between 2 presets at an

-7

even speed� Cruising will be invaild if you enable Auto Scan�

-8

2.1.4 Motion DetectionClick Channel Management on the main menu, enter into Motion Detection as shown�

•Motion Detection AreaChoose one camera channel and then set the area you need for motion detection� You can set multi-zone areas� Left click and drag the red box for motion detection area� The area can be cleared by draging the right mouse�

•Enable Motion DetectionCheck the box to make motion detection valid�

•SensitivitySensitivity level of motion detection�

•Apply to all camerasClick the button if you want to configure same settings to other cameras�

•Record DurationDuration of NVR continues recording after the moving object is detected�

2.1.5 Camera Config

-9

Click Channel Management on the main menu, enter into Camera Config as shown�• Status

Display camera status and version�

• Transfer Mode

There are Space priority and Speed priority for option� Choose the camera and make sure that the status is connected, and then choose mode, click Set to make it valid� Speed priority is recommended.

-10

• Camera ResolutionThis option is for 16-ch system only� You can choose a resolution of 640x352 or432x240 when there is 16-ch synchronous realtime live view� Click Set to make it valid� If there is 4-ch or 9-ch, the resolution is 1920x1080 or 1280x720�

• Display Camera TimeSelect the camera, check the box before Display Camera Time, click Set, it will display time on corresponding channel�

•Apply to all camerasClick the button if you want to configure same settings to other cameras�

2.2 Scheduled RecordClick Record Schedule button on the menu, enter into the interface as shown�

-11

•ChannelSelect the camera you want to configure�

• Record mode There are 2 record modes:1)Continuous RecordThe system will be recording untill you stop it�2)Motion RecordThe system will start recording only when there are movements in specific area� You can set detect area in Motion De t ection �3)No RecordJust for live view, no recording�

•Start time/End timeSet start time and end time of recording�

•DateChoose date which you want to set in schedule�

•SaveChoose record mode, start time and end time, click Save to set new record mode� The lower list on the interface will show the record mode when successfully done�

•Apply to all camerasClick to configure the same setting to other cameras�

2.3 Disk ManagementClick Disk management button on the main interface, enter into the interface as shown�

• FormatClick to format the disk�

-12

2.4 File ManagementClick File management button on the main interface, enter into the interface as shown�

You can backup record files and images to mobile storage device here�Steps：Insert the removable storage device into NVR, Select files to copy on the left listand select destination folder on the right list，click copy to backup� And eject mobile storage device�

2.5 System MaintainClick System Maintain button on the main interface, enter into the interface as shown�

• UpdateCopy update file into U-disk, and plug U-disk into NVR, click Update to updatethe system�

-13

2.6 System ConfigurationClick System Configuration button on the main interface，you can set network, modify users, etc�

2.6.1 GeneralClick System Configuration on the main menu, enter into General as shown�

•Output InterfaceIt supports VGA and HDMI�

•ResolutionChange screen resolution�

•System Date & System TimeSet Date and time�

•Device versionThe version information of system�

2.6.2 NetworkClick System Configuration on the main menu, enter into Network as shown�1.General Network setting• IP Setting

Setup the Ip address, subnet mask and gateway of the network card which needs to connect in the WAN� LAN is for public network card and the NVR's IP address, subnet mask and gateway should be setup here� IPC is RJ45 port of the cameras�

• Test NetworkClick to test whether network is well

-14

connected�

-15

2.DDNS

Register a free domain name with 4-8 characters (letters or numbers)� You can access NVR host After successfully applied�Notes：

When reinstall the NVR system, please delete the domain name first, otherwise the original domain name cannot be used�3.Other config

• Socket PortThe default socket port are 9000, you can change them to others，such as 9001.

• HTTP Server PortIn general, the default http server port is 80 when remote viewing through IE� you can also change it to other which is not in conflict with the other networking softwares in pc system, such as 90,8080� If changing 80 to other, input "http" before the domain name and a colon before HTTP Ser ver Port� For instance, change 80 to 90，you should input： http://*****.dvr99.org:90。

Notes：9000 can be changed，the number is better larger than 9000 to avoid conflicts with

-16

the otherpo r ts , such as 9001 �

-17

2.6.3 PreviewClick System Configuration on the main menu, enter into Preview as shown�

You can adjust resolution, brightness, contrast, saturation, chroma and sharpness of the monitor in VGA mode� You can also set interval of cycle view here, the minimum is 5 seconds�

2.6.4 UserClick System Configuration on the main menu, enter into User as shown�•AddClick Add to add new user, enter username and password, and check the items you want the sub-users have�

•EditSelect one user ， click to change settings according to your requirements�

•DeleteSelect one user ， click to delete it�

•Cameras accessible to remote userCheck channels so that user can view or control the chosen cameras remotely�

•Edit User interface

-18

2.6.5 RunningClick System Configuration on the main menu, enter into System Runnig as shown�

• Restart/Shut downCheck Date and Time to restrat/shut down NVR�

wapa-brasil.com.brwapa-brasil.com.br/.../uploads/2015/10/MANUAL-NVR.docx · Web viewNetwork Video...

Documents

Transcript of wapa-brasil.com.brwapa-brasil.com.br/.../uploads/2015/10/MANUAL-NVR.docx · Web viewNetwork Video...