Wall Mountable Electric Fireplace - Neostar Electronics · Wall Mountable Electric Fireplace with...
Transcript of Wall Mountable Electric Fireplace - Neostar Electronics · Wall Mountable Electric Fireplace with...
Wall Mountable Electric Fireplace with remote control Model: EF453S/ EFP02 (Pebbles fuel effect) Model: EF455S/ EFP03 (Log fuel effect)
INSTALLATION & INSTRUCTION MANUAL SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
GENERAL INFORMATION
Packaging Please DO NOT dispose of any packaging un�l you have checked the appliance is opera�onal. A�er removing the packaging ensure the contents are intact and complete. In the unlikely event of missing parts; contact your retailer. DO NOT leave children una�ended with any of the packaging since it is a poten�al source of danger. Disposal of all packaging must be carried out responsibly & safely and in accordance with your local authority regula�ons. ALWAYS recycle the packaging material where possible.
1
When using any electrically powered product, basic safety precau�ons should always be followed. PLEASE READ THE INSTRUCTIONS CAREFULLY & IN FULL BEFORE USING THE PRODUCT. Any ques�ons or problems? Please call our customer helpline on 0871 5905917
Contents
Heater Wall fixing bracket Fixing screws & wall plugs Remote control (requires 2xAAA 1.5v ba�eries, Not included) Instruc�on/installa�on manual Decora�ve pebbles (for EF453S/EFP01 Only) 40wa�s G9 halogen bulbs
2
IMPORTANT INSTRUCTIONS
Important Safety Instruc�ons WARNING -‐ to reduce the risk of fire, electrical shock or injury to persons or property: 1. Always operate the product from a power source of the same voltage, frequency
and ra�ng as indicated on the product iden�fica�on plate. 2. Close supervision is necessary when any appliance is used by or near the elderly or
the infirm. Do not allow children to use the appliance. 3. Do not operate the appliance with a damaged power cord or plug, or a�er the
appliance malfunc�ons, or is dropped or appears damaged in any way. Return the complete appliance to the place of purchase for inspec�on, repair or replacement.
4. To reduce the risk of electric shock, do not expose the appliance or power cord to moisture of any sort.
5. Do not operate the appliance near flammable materials or fire. 6. Switch off and unplug from the power socket when not in use, before assembling or
before cleaning. 7. Do not place objects on the appliance or allow objects to obstruct the inlet or outlet
openings, or operate in close proximity to curtains, loose drapes or furnishings. 8. The use of a�achments or accessories not recommended or sold by the product
distributor may cause injury to persons or damage to property. 9. This appliance is intended for normal domes�c/household use only. 10. Do not a�empt to disassemble the appliance unless as instructed to replace bulbs. 11. This appliance is designed ONLY to be wall mounted. 12. Do not use the appliance in ar�ficially hot or humid condi�ons or allow to be used in
a hazardous environment. 13. Do not clean the appliance with organic solvent. 14. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabili�es, or lack of experience and knowledge unless they have been given supervision or instruc�on concerning use of the appliance by a person responsible for their safety.
15. Children should not be le� unsupervised with the appliance. 16. This instruc�on manual is an integral part of the appliance and should be stored for
safe keeping and must always accompany the appliance in the event of ownership transfer or for reference to by a service engineer.
Any ques�ons or problems? Please call our customer helpline on 0871 5905917
INSTALLATION *** REQUIRES TWO PEOPLE ***
3
1. DO NOT connect the appliance to the mains power supply unit un�l the installa�on is correctly carried out and complete.
2. The minimum distances MUST be observed. 3. Take care when drilling fixing holes and ensure that no power cables, gas
or water pipes are behind the installa�on site. 4. The appliance is designed to fit permanently to a wall at a minimum
height of 300mm from the floor to the bo�om of the appliance.
Fig. 1
The wall bracket must be installed horizontally. Use a spirit level to ensure a true level. For best results install the wall bracket 1045mm from the floor to the fixing hole. Use the screws and wall plugs provided for standard wall installa�ons. Dry lined plaster board walls may require alterna�ve fixings. See Fig. 2
A height of 600mm from floor to the bo�om of the heater is recommended for op�mum viewing of the fuel bed. See Fig. 1
Fig. 2
Any ques�ons or problems? Please call our customer helpline on 0871 5905917
4
INSTALLATION CONTINUED
Any ques�ons or problems? Please call our customer helpline on 0871 5905917
Carefully li� the heater onto the wall bracket ensuring that the top rear ledge of the appliance engages the wall bracket and is si�ng centrally. See Fig.2 in circled detail. Bring the appliance level with the wall. Mark the bo�om hole posi�ons . Remove the appliance ensuring the bo�om fixing bracket is rotated up. Drill and fit wall plugs. Refit the appliance to the wall fixing bracket and rotate the bo�om fixing bracket down again and use the screw provided to permanently fit the appliance in place.
Fig. 3
Fig. 4
Unpack the decora�ve pebbles and arrange along the light unit in the desired posi�on.
Place the front glass surround over the front of the appliance aligning the slots in the brackets at each side of the glass panel with the lugs on the side of the appliance. See fig. 4
Any ques�ons or problems? Please call our customer helpline on 0871 5905917
5
OPERATION
A�en�on: -‐ Ensure the appliance is properly installed. Plug it into 220-‐240V~ 50Hz wall socket. -‐ The main power rocket switch located at the top right hand side of the appliance. Press ‘I’ to turn power on .
Manual Opera�on
• Press the O/I switch to turn the appliance ON and a RED LED will illuminate. Pressing & holding the O/I bu�on for three seconds will operate the dimmer mode.
• Press the 900W bu�on to operate the low heat se�ng. Press again to cancel the opera�on.
• Press the 1800W bu�on to operate the high heat se�ng. Press again to cancel the opera�on.
Main Power Switch
Any ques�ons or problems? Please call our customer helpline on 0871 5905917
6
OPERATION – Remote control
Remote Control Opera�on • There is a short �me delay a�er pressing a remote control opera�on. Wait three seconds before pressing any further bu�ons.
• Press the ON/OFF bu�on to turn the appliance ON. • Press the 900W bu�on to operate the low heat se�ng. Press again to cancel the opera�on.
• Press the 1800W bu�on to operate the high heat se�ng Press again to cancel the opera�on.
• Press the DIMMER bu�on to operate the dimmer mode.
How to install or change ba�eries (ba�eries not include) -‐ The polarity of ba�eries must match the indicator in the remote control. -‐ Don’t mix new and old ba�eries. -‐ If the remote control will not be used for a long period, take ba�eries out to avoid corrosion.
-‐ The ba�eries must be removed from the remote control before it is scrapped and dispose of them responsibly.
Note: Ba�eries contain materials, which are hazardous to the environment; they must be removed from the appliance at the end of their life and disposed of safely.
LAMP REPLACEMENT
7
Any ques�ons or problems? Please call our customer helpline on 0871 5905917
WARNING – Always disconnect the appliance from the mains power supply before replacing the bulbs.
CAUTION – The bulbs reach a high temperature during opera�on. Allow the bulbs to cool down before a�emp�ng to replace.
It is recommended that the appliance be removed from the wall and laid on its back in order to replace the bulbs. Carefully slide the glass panel towards the top of the appliance and li� off. Store the glass safely while the bulb is replaced.
At the bo�om of the appliance is a plate fixed with four Philips head screws. Remove the four screws and li� off the lamp cover. See fig. 5.
Fig. 5
Fig. 6
For access to the bulbs, carefully slide the rota�ng reflector to one side ensuring the rubber grommit is not lost. See fig. 6. Remove the defec�ve bulb by unscrewing it. Replace the bulb with a 40wa�s G9 halogen bulb taking care not to over �ghten it. Refit the rota�ng reflector ensuring the rubber grommit is carefully pushed into the slo�ed hole on the axial bracket. Li� the fire back onto the lugs either side of the appliance.
Replacement bulbs are available from any good DIY or hardware store.
OVERHEAT PROTECTION
8
Any ques�ons or problems? Please call our customer helpline on 0871 5905917
Maintenance
Before cleaning always disconnect the mains power supply. For general cleaning using a so�, moist cloth and a mild detergent. Do not use abrasive cleaners or proprietary glass cleaner.
CLEANING
This appliance is fi�ed with a safety cut out which will operate if the appliance overheats. For safety reasons the appliance will not automa�cally reset. To reset the appliance, disconnect the mains power supply for a minimum of 15 minutes. Reconnect the mains power supply and switch the appliance on. DO NOT block of obstruct the air vents as this will lead to the appliance overhea�ng and may cause a fire hazard.
9
Technical Specifica�on Power Supply: 220~240V~ 50Hz Rated Power : 1800wa�s Dimensions: 650mm x 520mm x 114mm Weight 12.9 kgs (EFP02) / 12.8 kgs (EFP03) Ligh�ng: 2 x 40wa�s G9 Halogen bulbs
Any ques�ons or problems? Please call our customer helpline on 0871 5905917
BS Plug Wiring
Wiring Instruc�ons: Should it be necessary to change the plug please note the wires in the mains lead are coloured in accordance with the following code:
BLUE -‐ NEUTRAL BROWN -‐ LIVE
GREEN OR GREEN/YELLOW -‐ EARTH
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings iden�fying the terminals in your plug, proceed as follows:
1. The BLUE wire is the NEUTRAL and must be connected to the terminal that is marked with the le�er N or coloured BLACK. 2. The BROWN wire is the LIVE and must be connected to the terminal that is marked with the le�er L or coloured RED. 3. Neither wire is to be connected to the terminal which is marked with the le�er E or earth symbol , coloured GREEN or GREEN/YELLOW. 4. Always ensure that the cord grip is posi�oned and fastened correctly. If a 13A (BS 1363) fused plug is used it must be fi�ed with a 13A (BS 1362) fuse. If in doubt consult a qualified electrician.
Wiring for a 13 Amp plug (BS 1363) The Earth Terminal is marked with the le�er E or Earth Symbol
TECHNICAL DATA
10
This product is guaranteed against faulty workmanship for a period of 12 months from date of purchase. Your guarantee will be invalidated if this product is modified in any way or not used in accordance with these instruc�ons. Proof of purchase is required if making a claim. Your statutory rights remain unaffected.
In the unlikely event of a problem, please contact our help desk on 0871 590 5917
Neostar Electronics is a registered brand of T2 Direct Ltd – London.
WARRANTY
ONE (1) YEAR LIMITED WARRANTY Retain this informa�on
This product has been manufactured to comply with: EC Council Direc�ve 2004/108/EC Electromagne�c compa�bility & Low Voltage direc�ve 2006/95/EC
Electrical products should not be disposed of with general household waste. Please recycle where facili�es exist.
For more informa�on on disposal contact your local authority.
11