Wall Hanging - Made By Marneymadebymarney.com/wp-content/uploads/2020/07/ENJOY-TODAY...wall hanging....
Transcript of Wall Hanging - Made By Marneymadebymarney.com/wp-content/uploads/2020/07/ENJOY-TODAY...wall hanging....
-
Wall Hanging Materials:
Size: 21” x 29”
1/2 yard Background
1/3 yard Sashing
1/4 yard Binding
2/3 yard Backing
Assorted scraps for paper
piecing/words/borders.
2/3 yard Batting
1/4 yard Heat N Bond
This is a Paper Pieced Pattern
© 2020 Mary A. Hertel All Rights Reserved
Visit me at: madebymarney.com
ENJOY TODAY
Wall Hanging
-
ENJOY TODAY WALL HANGING Finished Size: 21”x 29”
Materials:
Fabric A: 1/2 yard background to paper
piece 3 blocks and background for words.
Fabric B: 1/3 yard for sashing.
Fabric C: 1/4 yard for binding.
Fabric D: 2/3 yard for backing.
Assorted Fabric Scraps: for striped rows,
words, and paper piecing.
24” x 33” piece of batting.
Assorted buttons.
Heat N Bond Lite, 1/4 yard.
Black embroidery floss.
Cutting: Do all cutting before paper piecing.
WOF = width of fabric
Fabric A:
Cut 1 rectangle 9½” x 18½”.
Remainder of fabric is used for paper
piecing.
Fabrics B:
Cut 7 strips 1½”x WOF from each fabric.
Subcut 5 of these into strips 1½” x 18½”.
Fabric C:
Cut 3 strips 2½” x WOF.
Assorted Scraps:
From assorted scrap colors, cut 20
rectangles 2”x 4”, and cut 4 rectangles
2¼”x 4”.
Directions: Use ¼” seams throughout.
Sew all seams with right sides together,
unless otherwise directed.
Paper Pieced Blocks
1. Paper piece the ENJOY TODAY blocks
using Fabric A as the background fabric and
the assorted scraps.
2. Add any necessary embroidery. Do not
add any buttons at this time, but mark their
placement.
3. Trim the blocks as directed on each block
pattern. After sewing the blocks together,
the row will measure 8”x 18½”.
Section with Appliqued Words
1. Trace the letters for ENJOY TODAY onto
Heat N Bond Lite. Steam press the letters
onto the back of your fabric scraps.
2. Cut out letters, and arrange the letters on
the Fabric A 9½”x 18½” rectangle. Remove
paper from the back of the letters. Press in
place. Applique as desired.
Create the Striped Borders
1. Sew 10 of the 2”x 4” rectangles together
from the assorted scraps.
2. Sew a 2¼”x 4” rectangle to each end of
this row. (12 rectangles total) Press all
seams to one side.
3. Repeat for the second border.
Page 1
-
Attach the Sashing
1. Sew a Fabric B strip 1½”x 18½” to
connect all 4 sections, and to the top and
bottom of the unit, as shown below. Press
seams towards the sashing.
2. Sew a Fabric B strip 1½” x WOF to each
side of the wall hanging. Press seams
towards the sashing. Trim any excess
sashing.
Quilting
1. Remove the paper from the back of the 3
blocks.
2. Layer the wall hanging, facing right side
up, the batting in the middle, and the
backing Fabric D, facing right side down.
3. Pin all 3 layers together and quilt as
desired.
Binding
1. Sew the 3 Fabric C 2½”x WOF binding
strips together, laying the strips on a right
angle with the right sides together. Sew on
the diagonal to connect the strips. Trim
seam to ¼”.
2. Press the seams to one side and then
press the entire strip in half lengthwise with
the right sides facing out.
3. Align the raw edges of the binding strip
with the raw edges of the wall hanging.
Bend the beginning of the strip on an angle
as shown. It is recommended to start
thebinding at the bottom of the wall
hanging. Stitch ¼” from the edge and back
tack.
Page 2
Paper Pieced Row
ENJOY TODAY
-
4. Fold the binding strip straight up. The
raw edge of the binding strip should align
with the raw edge of the second side of the
wall hanging.
5. Bend the binding strip straight down to
overlap the second edge of the wall
hanging. Start stitching at the top corner
and continue until ¼” from the next corner
and back tack .
6. Continue in this manner around the
remaining sides of the wall hanging.
7. Trim the end of the binding strip so it
overlaps the angled beginning section by 2”.
Trim away the remaining tail.
8. Fold the binding to the back of the wall
hanging and hand sew in place.
For an instructional tutorial on Binding a
Quilt, visit my website:
madebymarney.com
Finishing
1. Sew buttons where indicated on the
patterns, sewing through all thicknesses.
2. Add a hanging sleeve to the back of the
wall hanging if desired.
Align
edges.
Back tack ¼” away from the
corner of the table runner.
Trim the tail.
Overlap beginning and end tails 2”.
Page 3