JIB-FM Series Floor Mounted Jib Cranes MANUAL.pdf · rev. 7/20/2017 jib-fm, manual
Wall Bracket Jib CranesThe Wall Bracket (WB100) Jib is the most economical means of providing hoist...
7
The Wall Bracket (WB100) Jib is the most economical means of providing hoist coverage for individual use in bays, along walls or columns of plants, or as a supplement to an overhead crane or monorail system. Two key requirements must be met before applying the Wall Bracket Series: 1. A structurally adequate wall or column to support the jib must exist 2. Sufficient clearance above the boom throughout its arc to accommodate the e rod suspension must exist Gorbel’s Advantage: Ease of Movement • Low dead weight of the boom combined with bronze bushings and oil-impregnated bronze thrust washers provide for easy rotaon and superior load posioning Safety • Formed bracket fings provide for greater reliability. No welds in tension, all bolts are in double shear for increased strength Full Rated Capacity • Pre-engineered for use with powered hoists. A factor of 15% of the jib crane capacity is allowed for the hoist and trolley weight with an addional 25% of the capacity allowed for impact, thus giving full rated capacity use of the jib Ease of Installaon • Single e rod, right hand threaded at both ends for easy leveling • All connecons bolted, including movable bolted trolley stops • Grease fings are provided for easy field lubricaon Top Bracket Fing Boom Bracket Fing Beam Bracket Fing The Thrust & Pull diagram above details the thrust and pull forces that the jib applies to the supporng structure when a load is liſted. It is essenal that a structurally adequate wall or column exists. Refer to the Thrust & Pull chart opposite this page for exact forces. Fing kits are available for fabricaon of cranes locally. Wall Bracket Jib Cranes An economical heavy duty soluon 200° Power rotaon is an available opon. Pull Thrust B (Bracket Center) A (Span) E W G G D WB100 - Wall Bracket Jib F 1 Distributed by Tri-State Equipment Company Inc. | [email protected] | (314) 869-7200 | www.tsoverheadcrane.com
Transcript of Wall Bracket Jib CranesThe Wall Bracket (WB100) Jib is the most economical means of providing hoist...
The Wall Bracket (WB100) Jib is the most economical means of providing hoist coverage for individual use in bays, along walls or columns of plants, or as a supplement to an overhead crane or monorail system.
Two key requirements must be met before applying the Wall Bracket Series:1. A structurally adequate wall or column to support the jib
must exist2. Sufficient clearance above the boom throughout its arc to
accommodate the tie rod suspension must exist
Gorbel’s Advantage:Ease of Movement• Low dead weight of the boom combined with bronze
bushings and oil-impregnated bronze thrust washersprovide for easy rotation and superior load positioning
Safety• Formed bracket fittings provide for greater reliability.
No welds in tension, all bolts are in double shear forincreased strength
Full Rated Capacity• Pre-engineered for use with powered hoists. A factor of
15% of the jib crane capacity is allowed for the hoist andtrolley weight with an additional 25% of the capacityallowed for impact, thus giving full rated capacity use ofthe jib
Ease of Installation• Single tie rod, right hand threaded at both ends for easy
leveling• All connections bolted, including movable bolted trolley
stops• Grease fittings are provided for easy field lubrication
Top Bracket Fitting
Bottom Bracket Fitting
Beam BracketFitting
The Thrust & Pull diagram above details the thrust and pull forces that the jib applies to the supporting structure when a load is lifted. It is essential that a structurally adequate wall or column exists. Refer to the Thrust & Pull chart opposite this page for exact forces.
Fitting kits are available for fabrication of cranes locally.
Wall Bracket Jib Cranes An economical heavy duty solution
200° Power rotation is an available option.
Pull
Thrust
B(Bracket Center)
A (Span)
E
W
G
G
D
WB100 - Wall Bracket Jib
F
1 Distributed by Tri-State Equipment Company Inc. | [email protected] | (314) 869-7200 | www.tsoverheadcrane.com
WB100 Wall Bracket
CAPACITY SPAN (A) MODEL NUMBER B D E F G WTIE ROD
DIAMETERTHRUST &
PULL
1/2 Ton
8’10’12’14’16’18’20’24’30’
WB100-G1-8-6WB100-G1-10-6WB100-G1-12-6WB100-G1-14-6WB100-G1-16-6WB100-G1-18-W8WB100-G1-20-W8WB100-G1-24-W8c6WB100-G1-30-12c8
2’ 9”3’ 0”3’ 9”4’ 6”5’ 6”6’ 0”6’ 6”7’ 6”
10’ 0”
1’ 3”1’ 6”1’ 9”2’ 0”2’ 0”2’ 0”2’ 3”2’ 6”3’ 6”
13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”
3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”
3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”
6”6”6”6”6”8”8”8”
12”
1”1”1”1”1”1”1”1”1”
3709#4408#4347#4317#4109#4453#4646#5426#6009#
1 Ton
8’10’12’14’16’18’20’24’30’
WB100-G1-8-6WB100-G1-10-6WB100-G1-12-6WB100-G1-14-W8WB100-G1-16-W8WB100-G1-18-W8WB100-G1-20-10WB100-G1-24-10c6WB100-G1-30-12c8
2’ 9”3’ 0”3’ 9”4’ 6”5’ 6”6’ 0”6’ 6”7’ 6”
10’ 0”
1’ 3”1’ 6”1’ 9”2’ 0”2’ 3”2’ 6”2’ 6”2’ 9”3’ 6”
13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”
3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”
3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”
6”6”6”8”8”8”
10”10”12”
1”1”1”1”1”1”1”1”1”
7273#8608#8453#8481#8055#8419#8966#9877#
10069#
2 Ton
8’10’12’14’16’18’20’24’30’
WB100-G2-8-W8WB100-G2-10-W8WB100-G2-12-W8WB100-G2-14-W8WB100-G2-16-10WB100-G2-18-12WB100-G2-20-12WB100-G2-24-12c8WB100-G2-30-12c8
2’ 9”3’ 0”3’ 9”4’ 6”5’ 6”6’ 0”6’ 6”7’ 6”
10’ 0”
1’ 3”1’ 6”1’ 9”2’ 0”2’ 3”2’ 3”2’ 6”3’ 0”3’ 0”
13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”13-1/2”
4”4”4”4”4”4”4”4”4”
4-1/8”4-1/8”4-1/8”4-1/8”4-1/8”4-1/8”4-1/8”4-1/8”4-1/8”
8”8”8”8”
10”12”12”12”12”
1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”
14464#17100#16772#16570#15864#16725#17348#18836#18189#
3 Ton
8’10’12’14’16’18’20’24’30’
WB100-G3-8-W8WB100-G3-10-W8WB100-G3-12-10WB100-G3-14-10WB100-G3-16-12WB100-G3-18-12c8WB100-G3-20-12c8WB100-G3-24-12c8WB100-G3-30-12c10
2’ 9”3’ 3”4’ 0”4’ 9”5’ 6”6’ 3”7’ 0”8’ 6”
11’ 0”
1’ 3”1’ 6”1’ 9”2’ 0”2’ 3”2’ 3”2’ 6”3’ 0”3’ 0”
14”14”14”14”14”14”14”14”14”
4”4”4”4”4”4”4”4”4”
4-5/8” 4-5/8”4-5/8”4-5/8”4-5/8”4-5/8”4-5/8”4-5/8”4-5/8”
8”8”
10”10”12”12”12”12”12”
1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”1-1/2”
21591#23539#23557#23514#23649#23970#24037#24197#24072#
5 Ton
8’10’12’14’16’18’20’24’30’
WB100-G5-8-12WB100-G5-10-12WB100-G5-12-12WB100-G5-14-12c8WB100-G5-16-W16WB100-G5-18-W16WB100-G5-20-W16WB100-G5-24-W16c12WB100-G5-30-W16c12
3’ 0”3’ 3”4’ 0”4’ 9”5’ 6”6’ 3”7’ 0”8’ 9”
11’ 0”
1’ 6”1’ 6”1’ 9”2’ 0”2’ 6”3’ 0”3’ 6”3’ 6”3’ 6”
15-1/4”15-1/4”15-1/4”15-1/4”15-1/4”15-1/4”15-1/4”15-1/4”15-1/4”
6”6”6”6”6”6”6”6”6”
7”7”7”7”7”7”7”7”7”
12”12”12”12”16”16”16”16”16”
2”2”2”2”2”2”2”2”2”
33006#39258#39072#39209#39229#39246#39286#39926#39376#
Model Number ExplanationExample: 3 Ton WB100-G3-20-12c8; 3 Ton = 6,000 pound capacity, WB100 = wall bracket style, 20 = span (A), 12 = beam size in inches (W), c8 = 8” cap channel welded to top of boom.
Other Sizes & Capacities Readily AvailableOther spans and capacities are available by contacting your local Gorbel® dealer.
Note: Dimensions are subject to change without notice.
Performance Jibs
2Distributed by Tri-State Equipment Company Inc. | [email protected] | (314) 869-7200 | www.tsoverheadcrane.com
The Wall Cantilever (WC200) provides hoist coverage and 200° rotation for individual use in bays, along walls or columns of plants, or as a supplement to an overhead crane or monorail system. The jib has the advantage of providing maximum lift for the hoist, since it can be installed very close to the underside of the lowest ceiling obstruction.
Two key requirements must be met before applying the Wall Cantilever Series:1. A structurally adequate wall or column to support the jib
must exist2. Sufficient clearance above the boom throughout its arc
must exist
Gorbel’s Advantage:Ease of Movement• The fittings contain bronze bushings and oil-impregnated
bronze thrust washers which provide for easy rotation andsuperior load positioning
Safety• Fabricated steel fittings provide excellent torsional rigidity
Full Rated Capacity• Pre-engineered for use with powered hoists. A factor of
15% of the jib crane capacity is allowed for the hoist andtrolley weight with an additional 25% of the capacityallowed for impact, thus giving full rated capacity use ofthe jib
Ease of Installation• When the bracket center dimension is 6’ 0” or less, the
mast/boom connection is welded. This provides the most economical means of installation
• When the bracket center is greater than 6’ 0”, a boltedmast/boom connection is used, which enables the largercranes to be shipped disassembled for ease of handlingduring shipping and installation
• Grease fittings are provided for easy field lubrication
The Thrust & Pull diagram above details the thrust and pull forces that the jib applies to the supporting structure when a load is lifted. It is essential that a structurally adequate wall or column exists. Refer to the Thrust & Pull chart opposite this page for exact forces.
Wall Cantilever Jib Cranes
Pull
Thrust
B(Bracket Center)
A (Span)
E
FW
G
G
W
An ideal jib for maximizing headroom
200° Power rotation is an available option.
WC200 Wall Cantilever Jib
Top and Bottom Bracket Fittings
Wall Cantilever fitting kits are available for fabrication of cranes locally.
3 Distributed by Tri-State Equipment Company Inc. | [email protected] | (314) 869-7200 | www.tsoverheadcrane.com
WC200 Wall CantileverCAPACITY SPAN (A) MODEL NUMBER B E F G W THRUST & PULL
1/4 Ton
8’10’12’14’16’18’20’
WC200-B1-8-6WC200-B1-10-6WC200-B1-12-6WC200-B1-14-W8WC200-B1-16-W8WC200-B1-18-W8WC200-B1-20-10
3’ 0”3’ 0”3’ 0”3’ 0”3’ 0”4’ 0”4’ 0”
5”5”5”5”5”5”5”
3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”
6”6”6”6”6”6”6”
6”6”6”8”8”8”
10”
1767#2308#2867#3624#4268#3704#4595#
1/2 Ton
8’10’12’14’16’18’20’
WC200-B1-8-W8WC200-B1-10-W8WC200-B1-12-W8WC200-B1-14-W8WC200-B1-16-10WC200-B1-18-10WC200-B1-20-12
3’ 0”3’ 0”3’ 0”4’ 0”4’ 0”4’ 0”6’ 0”
5”5”5”5”5”5”5”
3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”
6”6”6”6”6”6”6”
8”8”8”8”
10”10”12”
3459#4500#5565#4991#6063#6979#5493#
1 Ton
8’10’12’14’16’18’20’
WC200-B1-8-W8WC200-B1-10-10WC200-B1-12-10WC200-B1-14-10WC200-B1-16-12WC200-B1-18-W16WC200-B1-20-W16
4’ 0”5’ 0”5’ 0”5’ 0”6’ 0”6’ 0”6’ 0”
5”5”5”5”5”5”5”
3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”3-1/2”
6”6”6”6”6”6”6”
8”10”10”10”12”16”16”
5044#5294#6526#7778#7678#9148#
10367#
2 Ton
8’10’12’14’16’18’20’
WC200-B2-8-12WC200-B2-10-12WC200-B2-12-W16WC200-B2-14-W16WC200-B2-16-W18WC200-B2-18-W18WC200-B2-20-W21
4’ 0”4’ 0”4’ 6”5’ 0”6’ 0”6’ 6”7’ 6”
5”5”5”5”5”5”5”
4”4”4”4”4”4”4”
6”6”6”6”6”6”6”
12”12”16”16”18”18”21”
10054#12998#14409#15442#15067#15892#15840#
3 Ton
8’10’12’14’16’18’20’
WC200-B3-8-W16WC200-B3-10-W16WC200-B3-12-W16WC200-B3-14-W18WC200-B3-16-W18WC200-B3-18-W21WC200-B3-20-W21
4’ 0”4’ 6”5’ 6”6’ 0”7’ 6”8’ 6”9’ 6”
5”5”5”5”5”5”5”
4”4”4”4”4”4”4”
6”6”6”6”6”6”6”
16”16”16”18”18”21”21”
15060#17300#17390#19017#17653#17982#18105#
5 Ton
8’10’12’14’16’18’20’
WC200-B5-8-W18WC200-B5-10-W18WC200-B5-12-W21WC200-B5-14-W21WC200-B5-16-W24WC200-B5-18-W24WC200-B5-20-W24
6’ 6”6’ 6”6’ 6”7’ 6”9’ 6”9’ 6”9’ 6”
7”7”7”7”7”7”7”
6”6”6”6”6”6”6”
9”9”9”9”9”9”9”
18”18”21”21”21”24”24”
15323#19770#24379#25077#23240#26485#29769#
Model Number ExplanationExample: 1 Ton WC200-B1-12-10; 1 Ton = 2,000 pound capacity, WC200 = Wall Cantilever style, 12 = span (A), 10 = boom size in inches (W).
Other Sizes & Capacities Readily AvailableOther spans and capacities are available by contacting your local Gorbel® dealer.
Note: Dimensions are subject to change without notice.
Performance Jibs
4Distributed by Tri-State Equipment Company Inc. | [email protected] | (314) 869-7200 | www.tsoverheadcrane.com
WSJ200 Wall Cantilever Work Station Jibs: 200° Rotation
CAPACITYSPAN
(A)MODEL NUMBER
TRACK SERIES
WEIGHTB D G H T THRUST
& PULLin in in in in
150#
8’10’12’14’16’
WSJ200-150-8WSJ200-150-10WSJ200-150-12WSJ200-150-14WSJ200-150-16
250250250500500
160#181#216#282#330#
3636486060
10-3/810-3/813-3/816-7/816-7/8
555
7-1/87-1/8
99
121515
1-1/21-1/21-1/22-7/82-7/8
612#801#750#782#932#
250#
8’10’12’14’16’
WSJ200-250-8WSJ200-250-10WSJ200-250-12WSJ200-250-14WSJ200-250-16
250250500500500
160#198#252#282#330#
3648606060
10-3/813-3/816-3/816-7/816-7/8
55
7-1/87-1/87-1/8
912151515
1-1/21-1/22-7/82-7/82-7/8
962#933#945#
1160#1366#
500#
8’10’12’14’16’
WSJ200-500-8WSJ200-500-10WSJ200-500-12WSJ200-500-14WSJ200-500-16
500500500
10001000
188#213#252#384#416#
4848606060
13-3/813-3/816-3/816-7/816-7/8
7-1/87-1/87-1/87-7/87-7/8
121215
17-1/217-1/2
2-7/82-7/82-7/83-1/83-1/8
1390#1784#1750#2152#2512#
1000#
8’10’12’14’16’
WSJ200-1000-8WSJ200-1000-10WSJ200-1000-12WSJ200-1000-14WSJ200-1000-16
10001000100020002000
204#274#301#546#595#
4860607272
13-3/816-3/816-3/818-7/818-7/8
7-7/87-7/87-7/88-1/88-1/8
1215172020
3-1/83-1/83-1/82-7/82-7/8
2722#2781#3394#3451#4010#
Accessories for Work Station Jib CranesFestooning
Festoon Gliders are used to support flat electrical cable along the jib boom. No tools are required to attach the festooning to the gliders. Not available for AL100 jibs.
Festoon Trolleysare used to support flat cable, air hose or round cable along the jib boom. The trolleys have four wheels and a pivoting festoon saddle support.
Festoon Saddle: Gorbel’s Tool Solution saddles were designed for applications that require festooning of cables and hoses. The arched saddle with the option of angled mounting creates a very clean, efficient way to manage your cables and wires.
Saddles are available in 3 and 6 inch diameters for various sized festooning with a 75 pound capacity per saddle. The universal mounting plate allows for the saddle to hang in line with the track, or at a 30° angle to assist the cable in self-coiling, taking up less track space and allowing more room for end approach.
A (Span) H
TB
D
G
10”7” TYP
3” TYP
O5/8” Hardware (Provided by others)
Additional Sizes and Capacities Readily AvailableOther spans, heights, and capacities are available by contacting your local Gorbel® dealer.
Note: Dimensions are subject to change without notice.
WSJ200
5 Distributed by Tri-State Equipment Company Inc. | [email protected] | (314) 869-7200 | www.tsoverheadcrane.com
CAPACITYSPAN
(A)MODEL NUMBER
TRACK SERIES
WEIGHTB D G T TIE ROD
DIAMETERTHRUST & PULLin in in in
250#
8’10’12’14’16’
AL100-G1-250-8AL100-G1-250-10AL100-G1-250-12AL100-G1-250-14AL100-G1-250-16
A0250A0250A0250A0250A0250
165#178#190#203#216#
2427303336
1821242730
7-1/47-1/47-1/47-1/47-1/4
2-5/82-5/82-5/82-5/82-5/8
1”1”1”1”1”
1377#1567#1725#1861#1979#
500#
8’10’12’14’16’
AL100-G1-500-8AL100-G1-500-10AL100-G1-500-12AL100-G1-500-14AL100-G1-500-16
A0500A0500A0500A0500A0500
173#187#202#217#231#
3642485460
1821242730
7-1/47-1/47-1/47-1/47-1/4
2-5/82-5/82-5/82-5/82-5/8
1”1”1”1”1”
1800#1967#2097#2202#2290#
1000#
8’10’12’14’16’
AL100-G1-1000-8AL100-G1-1000-10AL100-G1-1000-12AL100-G1-1000-14AL100-G1-1000-16
A1000A1000A1000A1000A1000
203#225#246#268#289#
3033363942
1821242730
7-7/87-7/87-7/87-7/87-7/8
2-7/82-7/82-7/82-7/82-7/8
1”1”1”1”1”
4306#4987#5566#6066#6504#
2000#
8’10’12’14’16’
AL100-G1-2000-8AL100-G1-2000-10AL100-G1-2000-12AL100-G1-2000-14AL100-G1-2000-16
A2000A2000A2000A2000A2000
231#256#280#305#330#
4854606675
1821242730
12-7/812-7/812-7/812-7/812-7/8
2-7/82-7/82-7/82-7/82-7/8
1”1”1”1”1”
4982#5713#6307#6800#6929#
Rotation Options Four Ring Electrical Collector (Top or Bottom Entry - not shown) Provides continuous 360° rotation of the boom when using an electrical lifting device. The top entry collector requires 11 ¼ “ additional clearance height
Air Swivel (Top or Bottom Entry - not shown) Provides continuous 360 rotation of the boom when using an air powered lifting device. A top entry collector require 5” of additional clearance above the pivot pin. The bottom entry collector requires 8 ½ to 9 ½ inches above the pivot pin depending on span and capacity.
Manual Rotation Stops (not shown): To prevent boom damage to machines, equipment, or building structures, rotation stops can be used to the limit the WSJ360 rotation to less than 360°.
Trolley OptionsLight Tool Trolley: Designed specifically for suspended small tools, the light tool trolley features a six wheel design with the center wheel positioned slightly higher to prevent binding when force is applied at an angle. The short
wheel base allows for multiple trolleys to be used in a small area, making this trolley ideal for hanging tooling with spring balancers that require side loading capabilities. This trolley fits 250 series track in capacities up to 75 lbs.
Heavy Tool Trolley: The heavy tool trolley features six wheels with the center axis set higher to prevent binding. With a higher capacity and longer body profile, this trolley fits 500 series track in capacities up to 125
lbs., and can be used for suspending tools or festooning. An optional swivel attachment can be added to the bottom edge to support festooning of electrical, air or vacuum tube.
Additional Sizes and Capacities Readily AvailableOther spans, heights, and capacities are available by contacting your local Gorbel® dealer.
Note: Dimensions are subject to change without notice.
AL100 Wall Bracket Work Station Jibs: 200° Rotation
A (SPAN)
B
D
G8XO5/8” HARDWARE (PROVIDED BY OTHERS) T
3- 1/2” TYP
3- 1/2” TYP
3- 1/2” TYP3” TYP
AL100
Enclosed Track Jibs
6Distributed by Tri-State Equipment Company Inc. | [email protected] | (314) 869-7200 | www.tsoverheadcrane.com
FOR MORE INFORMATIONYour authorized Gorbel® dealer can give you more information on what makes Gorbel’s Ergonomic Work Station Cranes and other material handling products “A Class Above.”
OVERVIEW BROCHURE CRANES
FREE STANDING CEILING MOUNTED
ERGONOMIC STUDY
ERGONOMIC LIFTING
G-FORCE® & EASY ARM®
ERGONOMIC STUDY
FALL ARREST
TOOL SOLUTIONS
TETHER TRACKTM
GANTRY CRANES
TELESCOPINGINTERLOCK/TRANSFER
OVERVIEW DVD
CLEVELAND TRAMRAIL®
Distributed by Tri-State Equipment Company [email protected]: (314) 869-7200
![Pillar and wall-mounted slewing jib cranes · Max. load capacity [kg] Electric slewing Pillar-mounted slewing jib cranes Wall-mounted slewing jib cranes Jib type/design Max. outreach](https://static.fdocuments.in/doc/165x107/5b535fa87f8b9ae30b8be93d/pillar-and-wall-mounted-slewing-jib-cranes-max-load-capacity-kg-electric.jpg)
