7/28/2019 Vpact FDB N r4

1/6

VPact TP&N final distribution boards (FDB)

The Systems General Characteristics VPact Busbar System

ASTA CERTIFIED

FAULT LEVEL

17.5kA

7/28/2019 Vpact FDB N r4

2/6

VPact TP&N final distribution boards (FDB)

The Systems

The metal enclosure range of three phase and neutral distribution boards comprise of a primary

distribution board with 14 modules. This enables the product to accept a variety of incoming configurations to

offer a comprehensive range to meet most applications.

Engineered with:-

oFully flush fitted metal door with "slam" type catch.oThe pan assembly is fully shrouded and the busbars are of one piece design, this ensures that no "hotspots"

can occur.

oA removable gland plate allows the cable entry from either top or bottom, and yet ready to mount multiservice din rail extension boxes for modular devices.

oThe boards have been designed and independently ASTA type tested to IEC 60439-1:2004.The Busbar System are modular designed and certified with the MCCB to provide superior

performance, flexibility and value. Simply the best solution for your distribution panel needs.

Robust powder coated

sheet metal enclosure

Flush Door Latch

With Slam type catch

Document Pocket

Easier access for FDBs

detail

Removable gland plate

(for both top/bottom)

Full flush fitter door

7/28/2019 Vpact FDB N r4

3/6

VPact TP&N final distribution boards (FDB)

The Features

The Final Distribution Board is designed with 2-bolt system escutcheon for IP3x enclosure, yet it does

not compromise on the FULL ACCESSIBILITY in the panel.

Earth Protection

Well connected for all

metal panels

Terminal Bar

For sectionized wiring

management.

Modular Configuration

Section 1 and 2 Pan Assembly- Outgoing

circuit

Fit with SP, TP, MCB, 1 module RCBO

Totally enclosed, busbar system

rated at 200A

Color coded circuit designation

Premium Materials make a premium busbar system:

Electro-Galvanized material with polymerized enamel enabled enclosure subject to greatest fluctuation in allweather condition.State of art busbar system made from solid hard drawn high conductivity with tin-plated copper busbars andconnectors to minimize temperature raise and promote effective conductivity without deterioration.

molded thermoplastic terminal shroud to maintain alignment and ensure electrical isolation between phases

(eliminate flash over)

full personal safety, high quality andreliability

Incoming devices

ELR

ISOLATOR

MCB

MCCB

RCCB

Switch fuses

Terminal Shroud

7/28/2019 Vpact FDB N r4

4/6

VPact TP&N final distribution boards (FDB)

General Characteristics The Busbar System is designed and ASTA certified tomeet international requirements specified in IEC 60439-1:2004

relating to construction of Low Voltage Switchgear and control

gear assemblies, including:

Verification of Characteristics

Temperature rise limits [clause 8.2.1]Dielectric properties [clause 8.2.2]Short-circuit withstand strength [clause 8.2.3]Effectiveness of the Protection Circuits [clause 8.2.4]Clearances and Creepage distance [clause 8.2.5]Mechanical operation [clause 8.2.6]Degree of protection of Assemblies and form of separation

[clause 8.2.7]

Electromagnetic compatibility (EMC) [clause 8.2.8]Resistance of Insulating Material to Abnormal Heat and Fire

[clause 8.2.9]

The FDB has undergone full type test in accordance to

IEC 60439-1 Standards. The results of these tests guarantee the

performance of and by using the metalwork structures,

full modular busbar systems, adaptation to MCBs.

Safe operation with fully concealed

busbar and terminals.

Split Busbar System

Split Bar Systems

Localizing the control with effective tripping sensitivity at30mA and 100mA

Neat and tidy cable management for greater maintenanceaccessibility

7/28/2019 Vpact FDB N r4

5/6

VPact TP&N final distribution boards (FDB)

a TP&N Distribution Boards up to 200A incoming with Split Busbar System, 63A

Designation

No of ways Rated

Incoming

Capacity

Model Number

I II III IV V StandardFlush

Type

TP& N 2 60A FBSA0406 FBSA0406F

+

2 100A FBSA0410 FBSA0410F

2 2 60A FBSA0606 FBSA0606F

+ +

4 2 100A FBSA0610 FBSA0610F

2 4 6 60A FBSA0806 FBSA0806F

+ + +

6 4 2 100A FBSA0810 FBSA0810F

2 4 6 8 60A FBSA1006 FBSA1006F

+ + + +

8 6 4 2 100A FBSA1010 FBSA1010F

4 6 8 60A FBSA1206 FBSA1206F

+ + +

8 6 4 100A FBSA1210 FBSA1210F

4 6 8 10 60A FBSA1406 FBSA1406F

+ + + +

10 8 6 4 100A FBSA1410 FBSA1410F

a TP&N Distribution Boards up to 200A incoming with Single Busbar System, 63A

(max) outgoing

Designation No of ways

Rated

Incoming

Capacity

Model Number

Standard Flush Type

TP& N

oWith 14modules cutout for MCCB incomer 4 200A FB0420 FB0420F6 200A FB0620 FB0620F

8 200A FB0820 FB0820F

10 200A FB1020 FB1020F

12 200A FB1220 FB1220F

14 200A FB1420 FB1420F

16 200A FB1620 FB1620F

ASTA certified with Fault Level, Icw = 17.5kA rms for 0.2s,35KkA peak

With split bars system comprises 14 modules cutout(max) for MCB, isolator, RCCB and Switch fuse incomer

7/28/2019 Vpact FDB N r4

6/6

VPact TP&N final distribution boards (FDB)

Busbar System Pan Assembly

Designation No of ways Model No

Pan Assemblyo Rated Incoming Current max 200Ao Full expandable up to 16 moduleso Easy Access removable of Pan and MCB for installation and

maintenance purpose.

o Enclosed Busbar System

4 BB042

6 BB062

8 BB082

10 BB102

12 BB122

14 BB142

16 BB162

aBusbar System

Adaptability

ELR ISOLATOR

MCB RCCB

MCCB