VME VP A45/ 01x-RC Ruggedized Rx - Se riesredlinx.co.za/PDF/CCT_vme.pdf · nauto system controller...

CONCURRENTTECHNOLOGIES

Con cur rent Tech nol o gies Plc 4 Gilberd Court, Colchester, Essex, CO4 9WN, UKTel: +44 (0)1206 752626 Fax: +44 (0)1206 751116

Con cur rent Tech nol o gies Inc 6 Tower Of fice Park, Woburn, MA 01801, USATel: (781) 933 5900 Fax: (781) 933 5911email: [email protected] http://www.gocct.com

The VP A45/01x-RC is a PC-compatible low power, high

functionality, ruggedized conduction-cooled 6U VME

board supporting the 1.6 GHz Intel® Atom™ processor

N270. It utilizes the Intel® 945GSE mobile chipset to

support 2 Gbytes of DDR2-533 SDRAM. This single slot

board features 1 PMC/XMC site and 1 PMC site, an

on-board CompactFlash™ site and a range of I/O

including two Ethernet interfaces. The VP A45/01x-RC

is a ruggedized conduction-cooled board, operating in

temperatures from -40°C to +85°C, making it suitable

for a range of applications within the industrial

control, transport, security, aerospace and defense

industries. The board is rear I/O plug compatible with

the commercial and the ruggedized air-cooled

versions. To simplify the board’s integration many

industry standard operating systems are supported.

AP PLI CA TIONS

n Ruggedized 6U single board computer:- conduction cooled to IEEE 1101.2- supports 2 conduction-cooled PMC modules

conforming to ANSI/VITA 20- -40°C to +85°C operating temperature- conformally coated

n 1.6 GHz Intel® Atom™ processor:- 512 Kbytes L2 cache- Intel® Hyper-Threading Technology supports 2

execution threadsn 2 Gbytes of DDR2-533 SDRAM

n Dual SATA150 drive interfaces

n Option for an on-board SATA 2.5-inch solid state drive

n EIDE interface for an on-board CompactFlash® socket

n 1 x PMC/XMC and 1 x PMC module interfaces:- 1 x 32-bit, 33MHz PCI PMC site- 1 x 32/64-bit, 33/66 MHz PCI/PCI-X™ PMC site- 1 x XMC module interface (x1 PCI Express™)

n Keyboard, mouse and DVI-D graphics interfaces via P2

n 1 x serial channel and 2 x USB 2.0 interfaces

n 2 x Ethernet interfaces:- 2 x 10/100/1000Mbps Ethernet channels via P0

n Built-In Test (BIT) support planned:- Power-on BIT, Initiated BIT, Continuous BIT

n Watchdog and long duration timer

n 4 Mbytes of BIOS Flash EPROM

n VME64 interface supportingA32/A24/A16/D64/D32/D16/D8(E0), MBLT64

n Ruggedized air-cooled version:- -40°C to +75°C, conformally coated- see separate VP A45/01x-RA datasheet

n Non-ruggedized air-cooled versions:- rear plug compatible with ruggedized version- useful for bench development- useful in commercial (non-rugged) applications- see separate VP A45/01x datasheet

n Support for Linux®, Windows® XP, Windows® XPEmbedded, QNX® and VxWorks®

HIGHLIGHTS

Intel® Atom™ Pro ces sorDual PMC Con trol lerRug ged Con duc tion-Cooled

VP A45/01x-RCVMERuggedized Rx - Se ries

alastair

RL Emb WWW Bdr

http://www.redlinx.co.za/

Spec i fi ca tionRuggedized Dual PMC Con trol lern conduction cooled to IEEE 1101.2n supports 2 x conduction-cooled PMC modules

conforming to ANSI/VITA 20n conformally coatedn ruggedized air-cooled version available:-è see VP A45/01x-RA datasheet

n non-ruggedized commercial versionavailable:-è see VP A45/01x datasheet

Cen tral Pro ces sorn 1.6 GHz Intel® Atom™ processor N270:-è 512 Kbytes of secondary (L2) on-die cacheè 533 MHz Front Side Busè Intel Hyper-Threading Technology

supporting 2 execution threadsn uses 437 pin FC-BGA (Flip-Chip Ball Grid

Array) packagen utilizes Intel® 945GSE mobile class chipset:-è uses Intel® ICH7M I/O Hub

SDRAMn 2 Gbytes soldered DDR2-533 SDRAMn accessible from processor or VME bus

Mass Stor age In ter facesn 1 x EIDE interface supports on-board

CompactFlash™ socketn 2 x Serial ATA150 interfaces:-è transfer rate up to 150 Mbytes/sè accessed via P2 connectorè one channel switchable to optional

on-board SATA 2.5-inch solid state drive

Ethernet In ter facesn 2 x 10/100/1000 Mbps interfaces via P0:-è implemented by 2 x Intel® 82574 LAN

Controllers via x1 PCI Express® links

PMC/XMC In ter facesn 1 x PMC/XMC site and 1 x PMC siten PMC site 1 supports:-è 32/64-bit, 33/66 MHz PCI/PCI-Xè 3.3V or 5V signalingè XMC interface via x1 PCI Express portè I/O via P2 (VITA 35 P4V2-64ac pinout)

n PMC site 2 supports:-è 32-bit, 33MHz PCI onlyè 3.3V or 5V signalingè I/O via optional P0

Graphics In ter facen implemented by Intel 945GSE:-è resolutions up to 1600 x 1200 @ 16M colors

n DVI-D graphics accessed via P2 connector

Se rial In ter facesn 1 x RS232/422/485 serial channel accessed

via P2:-è supporting RI, CTS, RTS, DSR, DTR, DCD

and RIn 16550 compatible UART

Flash EPROMn 4 Mbytes of BIOS Flash EPROM

Soft ware Sup portn supports Linux®, Windows® XP, Windows® XP

Embedded, QNX®, and VxWorks®

Built-In Test (BIT) Sup portn Power-on BIT (PBIT)n Initiated BIT (IBIT)n Continuous BIT (CBIT)

Firm ware Sup portn Phoenix™ TrustedCore BIOS n comprehensive Power-On Self-Test (POST)n LAN boot firmware included

Other Pe riph eral In ter facesn PC-compatible Real Time Clockn 2 x USB 2.0 interfaces via P2 connectorn keyboard and mouse interfaces accessed via

P2 connectorn watchdog timern 1 x 32-bit Long Duration Timer with processor

interrupt capabilityn 4 x GPIO signals via P2

VME In ter facen P1 and P2 connectors compatible with VME64xn implemented using Tundra® Tsi148 devicen VME Master/Slaven A32/A24/A16/D64/D32/D16/D8(EO)/MBLT64n fast hardware byte swapping n auto system controller detectn full interrupter/interrupt handler support

Elec tri cal Spec i fi ca tionn typical current figure (2 Gbytes SDRAM)n +5V @ 4.4A; voltage +5% / -3%n +12V @ 0.0A; -12V @ 0.0A; 3.3V not requiredn +12V and -12V routed to both PMC sites

Safetyn PCB (PWB) manufactured with flammability

rating of 94V-0

En vi ron men tal Spec i fi ca tionn operating temperature:-è VITA 47 Class CC4, -40°C to +85°Cè conduction-cooled (VITA 48.2)

n storage temperature:-è VITA 47 Class C4, -55°C to +105°C

n operating and storage altitude:-1,000 to 50,000 feet (-305 to 15,240 meters)

n 5% to 95% Relative Humidity, non condensing(operating/storage)

n ruggedized and commercial air-cooled versions:-è rear plug compatibleè air-cooled: VP A45/01x-RA è commercial: VP A45/01x

Me chan i cal Spec i fi ca tionn 6U form-factorn single slot, front panel width 0.8 inch (20.3mm)n utilizes 160-way connectors for P1 and P2n optional P0n operating mechanical:- è shock - VITA 47 Class OS2, 40g è random vibration - VITA 47 Class V3, 0.1g²/Hz

OR DER ING IN FOR MA TIONOr der Num ber Prod uct De scrip tion (Hard ware) Re place the or der num ber suf fix (-xy) with se lec tions from the fol low ing:

Where x = P2/P0 Break out com bi na tions Where y = SDRAM size

VP A45/013-x2RC 1.6 GHz Atom pro ces sor N270 5 - No P0, 3.3V PMC, PMC (VITA35 P4V2-64ac) 1 - re served6 - P0 fit ted, 3.3V PMC, PMC (VITA35 P4V2-64ac) 2 - 2 Gbytes7 - No P0, 5V PMC, PMC (VITA35 P4V2-64ac) 8 - P0 fit ted, 5V PMC, PMC (VITA35 P4V2-64ac)

AD 110/001-z2RC SATA 2.5-inch Solid State Drive kit

All com pa nies and prod uct names are trade marks of their re spec tive or ga ni za tions. Datasheet Code 1592/0310Spec i fi ca tion sub ject to change; E and OE. RoHS 2002/95/EC com pli ant. © Con cur rent Tech nol o gies 2010

PM

C M

od

ule

1

XM

C

PM

C M

od

ule

2

KeyboardInterface

(P2)

MouseInterface

(P2)

2 xUSB 2.0

1 XRS232/RS482/RS485

(P2)

2 xUSB(P2)

4 xGPIO(P2)

PCI-33

x4

1 x SerialInterface

BIOSFlash

Real-TimeClock

2 x Ethernet 10/100/1000Mbps

(Optional P0)

VME Bus

Intel82574

x1 x1

x1

x1

DVI-D(P2)

2 x SATA150 (P2)

= PCI Express

PMCRear I/O(Optional

P0)

PMCRear I/O

(P2)VITA35

IntelAtomN270

CFTM

DRAMDDR2-533

2 x SATA150

GPIO

TSi148

Intel ICH7M

KeyboardInterface

MouseInterface

PCI-Eto PCI-XBridge

Intel945GSE

Intel82574

ByteSwap

SSD

PCI-X 66

alastair

RL Emb WWW Bdr





The VP A45/01x is a PC-compatible low power, high

functionality, 6U VME board supporting the 1.6 GHz

Intel® Atom™ processor N270. It utilizes the Mobile

Intel® 945GSE Express chipset to support 2 Gbytes of

DDR2-533 SDRAM. This single slot board features 1

PMC/XMC site and 1 PMC site, an on-board

CompactFlash™ site and a range of I/O including four

Ethernet interfaces. The VP A45/01x is a commercial

air-cooled board, suitable for a range of environments

within industrial control, transportation, security,

telemetry, scientific and medical applications.

Options to operate in temperatures ranging from

-40°C to +85°C are available. A ruggedized

conduction-cooled version is planned and a

ruggedized air-cooled version is available. To simplify

the board’s integration many industry standard

operating systems are supported.

AP PLI CA TIONS

n 1.6 GHz Intel® Atom™ processor N270:- 512 Kbytes L2 cache- Intel® Hyper-Threading Technology supports 2

execution threadsn 2 Gbytes of DDR2-533 SDRAM

n Dual SATA150 drive interfaces

n Option for an on-board SATA 2.5-inch mass storagedevice

n EIDE interface for an on-board CompactFlash® socket

n 1 x PMC/XMC and 1 x PMC module interfaces:- 1 x 32-bit, 33 MHz PCI PMC site- 1 x 32/64-bit, 33/66 MHz PCI/PCI-X™ PMC site- 1 x XMC module interface (x1 PCI Express™)- Expansion carrier for 2 more PMC/XMC sites

n Keyboard, mouse and DVI-D graphics interfaces via P2

n 2 x serial channels and 3 x USB 2.0 interfaces

n Watchdog and long duration timer


n 4 x Ethernet interfaces:- 1 x 10/100Mbps and 1 x 10/100/1000Mbps Ethernet

channels via front panel RJ45 connectors- 2 x 10/100/1000Mbps Ethernet channels via P0

n VME64 interface supportingA32/A24/A16/D64/D32/D16/D8(E0), MBLT64

n Extended temperature versions available:- -25°C to +70°C (E-Series)- -40°C to +85°C (K-Series, includes humidity sealant)

n Ruggedized air-cooled version (RA-Series) available:- -40°C to +75°C, conformally coated- see separate VP A45/01x-RA datasheet

n Ruggedized conduction-cooled version (RC-Series)planned:- conduction-cooled to ANSI/VITA 30.1-2002- -40°C to +85°C, conformally coated- see separate VP A45/01x-RC datasheet

n Support for Linux®, Windows® XP, Windows® XPEmbedded, QNX® and VxWorks®

HIGHLIGHTS

VP A45/01xVME

Intel® Atom™ ProcessorDual PMC Con trol ler

N, E, K - Se ries

RoHS2002/95/EC

alastair

RL Emb WWW Bdr


Spec i fi ca tionCen tral Pro ces sorn 1.6 GHz Intel® Atom™ processor N270:-è 512 Kbytes of secondary (L2) on-die cacheè 533 MHz Front Side Busè Intel Hyper-Threading Technology

supporting 2 execution threadsn utilizes Mobile Intel® 945GSE Express

chipset:-è uses Intel® ICH7M I/O Hub

SDRAMn 2 Gbytes soldered DDR2-533 SDRAMn accessible from processor or VME bus

Mass Storage In ter facesn 1 x EIDE interface supports on-board

CompactFlash™ socketn 2 x Serial ATA150 interfaces:-è transfer rate up to 150 Mbytes/sè accessed via P2 connectorè one channel switchable to on-board SATA

2.5-inch mass storage devicen option for USB Flash drive module

Ethernet In ter facesn 1 x 10/100Mbps interface via front panel:-è provided by Intel ICH7M

n 1 x 10/100/1000Mbps interface via frontpanel:-è implemented by Intel® 82574 LAN

Controller via x1 PCI Express® linkn 2 x 10/100/1000 Mbps interfaces via P0:-è implemented by 2 x Intel® 82574 LAN

Controllers via x1 PCI Express® links

PMC/XMC In ter facesn 1 x PMC/XMC site and 1 x PMC siten PMC site 1 supports:-è 32/64-bit, 33/66 MHz PCI/PCI-Xè 3.3V or 5V signalingè XMC interface via x1 PCI Express portè I/O via front panel and via P2 (VITA 35

P4V2-64ac pinout)n PMC site 2 supports:-è 32-bit, 33MHz PCI onlyè 3.3V or 5V signalingè I/O via front panel and via optional P0

n expansion to optional dual PMC/XMC carrierboard:-è via x1 PCI Express XMC site

Se rial In ter facesn 1 x RS232 serial channel accessed via RJ45

connector on front panel:-è supporting CTS, RTS, DSR, DTR and DCD

n 1 x RS232/422/485 serial channel accessedvia P2:-è supporting RI, CTS, RTS, DSR, DTR, DCD

and RIè 16550 compatible UART

Graphics In ter facen implemented by Intel 945GSE:-è resolutions up to 1600 x 1200 @ 16M colors

n DVI-D graphics accessed via P2 connector

Flash EPROMn 4 Mbytes of BIOS Flash EPROM

Soft ware Sup portn supports Linux®, Windows® XP, Windows® XP

Embedded, QNX®, and VxWorks®

Firm ware Sup portn Phoenix™ TrustedCore BIOS n comprehensive Power-On Self-Test (POST)n LAN boot firmware included

Other Pe riph eral In ter facesn PC-compatible Real Time Clock (Year 2000

compliant)n 3 x USB 2.0 interfaces:-è 1 via a USB connector on front panelè 2 via P2 connector

n keyboard and mouse interfaces accessed viaP2 connector

n watchdog timern 1 x 32-bit Long Duration Timer with processor

interrupt capabilityn 4 x GPIO signals via P2

VME In ter facen P1 and P2 connectors compatible with VME64xn implemented using Tundra® Tsi148 devicen VME Master/Slaven A32/A24/A16/D64/D32/D16/D8(EO)/MBLT64n fast hardware byte swapping n auto system controller detectn full interrupter/interrupt handler support


rating of 94V-0

Elec tri cal Spec i fi ca tionn [email protected] A (typical, 2Gbytes SDRAM)n [email protected]; [email protected]; 3.3V not requiredn +12V and -12V routed to both PMC sites

En vi ron men tal Spec i fi ca tionn operating temperatures:-è 0°C to +55°C (N-Series)è -25°C to +70°C (E-Series)è -40°C to +85°C (K-Series)

n storage temperature - VITA 47 Class C1n operating altitude - 0 to 15,000 feet (0 to

4,572 meters)n 5% to 95% Relative Humidity, non condensing

(operating or storage):-è K-Series includes humidity sealant

n ruggedized versions planned, see separatedatasheets:-è conduction-cooled: VP A45/01x-RCè air-cooled: VP A45/01x-RA

Me chan i cal Spec i fi ca tionn 6U form-factorn single slot, front panel width 0.8 inch

(20.3mm)n utilizes 160-way connectors for P1 and P2n optional P0n IEEE 1101.10 handlesn operating shock - VITA 47 Class OS1 n operating vibration - VITA 47 Class V1

OR DER ING IN FOR MA TIONOr der Num ber Prod uct De scrip tion (Hard ware) Re place the or der num ber suf fix (-xy) with se lec tions from the fol low ing:

Where x = P2/P0 Break out com bi na tions Where y = SDRAM size

VP A45/013-x2 1.6 GHz Atom pro ces sor N270 5 - No P0, PMC (VITA35 P4V2-64ac) 1 - re served6 - P0 fit ted, PMC (VITA35 P4V2-64ac) 2 - 2 Gbytes

AD 110/001-zz SATA 2.5-inch Mass Stor age Drive kitAD CR3/PMC-zz PMC Car rier board for 2 PMC mod ules

AD VP2/020-10 Rear Tran si tion Mod ule with I/O pe riph eral con nec tors, no P0: use when x = 5, i.e. VP A45/013-5yAD VP2/020-30 Rear Tran si tion Mod ule with I/O pe riph eral con nec tors, P0 fit ted: use when x = 6, i.e. VP A45/013-6yAD 235/001-0z USB Flash Drive Mod ule (op tional, fits on VP A45/01x baseboard)

For z op tions please con tact your lo cal sales of fice For ex tended tem per a ture, 1.6 GHz E and K-Se ries, please con tact your lo cal sales of ficeFor ruggedized ver sions, see sep a rate datasheets: VP A45/01x-RC (con duc tion-cooled) or VP A45/01x-RA (air-cooled))


PM

C M

od

ule

1

XM

C

PM

C M

od

ule

2

PMC/XMCInterface

1 xEthernet10/100Mbps

1 xEthernet

10/100/1000Mbps

1 xUSB

PMCInterface

KeyboardInterface

(P2)

MouseInterface

(P2)

4 xUSB 2.0 3V

1 XRS232/RS482/RS485

(P2)

2 xUSB(P2)

4 xGPIO(P2)

PCI-33

PCI-X 66

x4

2 x SerialInterfaces

1 xRS232

BIOSFlash

Real-TimeClock

2 x Ethernet 10/100/1000Mbps

(Optional P0)

VME Bus

Intel82574

x1 x1

x1

x1

DVI-D(P2)

2 x SATA150 (P2)

= PCI Express

Intel82574

PMCRear I/O(Optional

P0)

PMCRear I/O

(P2)VITA35

IntelAtomN270

CFTM

DRAMDDR2-533

2 x SATA150

GPIO

TSi148

Intel ICH7M

KeyboardInterface

MouseInterface

PCI-Eto PCI-XBridge

Intel945GSEExpress

Intel82574

ByteSwap

x1

USBFlashDrive




The VP 717/08x is a PC-compatible high performance,

high functionality VME processor board based on the

Intel® Core™ i7 processor up to 2.53 GHz (32nm process

technology), the Mobile Intel® QM57 Express chipset

and up to 8 Gbytes of DDR3-1066 ECC SDRAM. This

single slot board features 2 PMC/XMC sites and a variety

of interfaces including an option for an on-board Hard

Disk Drive or CompactFlash™. The VP 717/08x is suitable

for a range of demanding applications within the

defense, industrial control, telecomms, telemetry,

scientific and aerospace markets. To simplify the

board's integration many popular industry standard

operating systems are supported. For harsher

environments, extended temperature, ruggedized

air-cooled and ruggedized conduction-cooled versions

are supported. The board is plug compatible with the

popular VP 417/03x and VP 31x/02x families.

AP PLI CA TIONS

n 2.53 GHz, 2.0 GHz or 1.33 GHz Intel® Core™ i7 processor:- dual-core processor- 1066 MHz DRAM Bus (800 MHz for 1.33 GHz processor)- 4 Mbytes shared last level cache- Intel® Hyper-Threading Technology- Intel® Turbo Boost technology- Intel® 64 Technology (64-bit computing support)

n Up to 8 Gbytes of dual channel DDR3-1066 ECC SDRAM

n High performance SATA and EIDE disk interfaces withsupport for optional on-board disk drive

n Onboard CompactFlash™ site

n 2 x PMC/XMC module interfaces:- 32/64-bit, 33/66/100 MHz PCI/PCI-X™- 2 x XMC module interfaces (x8 PCI Express®)- Expansion carrier for 2 more PMC sites

n 2 x 10/100/1000 Mbps Ethernet interfaces:- Gigabit Ethernet for VME64x backplane (VITA 31.1)

n 3 x serial channels and 3 x USB 2.0 interfaces

n Analog graphics, keyboard and mouse interfaces

n VME-64 Interface supportingA32/A24/A16/D64/D32/D16/D8(EO), MBLT64 and withsupport for fast hardware byte-swapping


n 64 Mbytes of Application Flash EPROM

n Watchdog timer; Long Duration Timer

n Single slot

n Extended temperature versions:- -25°C to +70°C (E-Series)- -40°C to +85°C (K-Series, includes humidity sealant)

n Ruggedized air-cooled versions (RA-Series):- -40°C to +75°C, conformally coated

n Ruggedized conduction-cooled versions (RC-Series):- conduction-cooled to ANSI/VITA 30.1-2002- -40°C to +85°C, conformally coated

n Optional Built-In Test (BIT) support:- Power-on BIT, Initiated BIT, Continuous BIT

n Support for Linux®, Windows® 7, Windows® EmbeddedStandard 7, Windows® XP, Windows® XP Embedded,Windows® Server 2003, Windows® Server 2008,VxWorks®, QNX®, Solaris™ and LynxOS®

HIGHLIGHTS

VP 717/08xVME

Intel® Core™ i7 Pro ces sor Dual PMC/XMCEm bed ded Con trol ler

N, E, K - Se ries

alastair

RL Emb WWW Bdr


Spec i fi ca tionCen tral Pro ces sorn 2.53 GHz Intel® Core™ i7-610E processor,

2.0 GHz Intel® Core™ i7-620LE processor or 1.33 GHz Intel® Core™ i7-660UE processor

n common processor features are:-è 32nm process technologyè dual-core processorè 4 Mbytes shared last level cacheè Intel® Hyper-Threading Technologyè Intel® 64 Technology (64-bit computing)è Intel® Turbo Boost technologyè uses Ball Grid Array package

n processor to DRAM memory, bus speed:-è 610E and 620LE - 1066MHzè 660UE - 800MHz

n graphics engine, core clock speed:-è 610E - 500MHz è 620LE - 266MHz è 660UE - 166MHz è Intel Turbo Boost technology allows faster

graphics engine speed depending on theCPU loading

n utilizes Intel® Platform Controller Hub (PCH):-è Mobile Intel® QM57 Express chipset

DRAMn up to 8 Gbytes DDR3-1066 ECC SDRAM:-è up to 8 Gbytes soldered on-boardè single bit error correctionè peak bandwidth of 17 Gbytes/sè dual channel architecture

n accessible from processor or VME bus

Mass Stor age In ter facesn 2 x external drive interfaces supporting:-è single EIDE drive via P2 connectorè single SATA300 drive via P0 (see Note 1)

n optional on-board 2.5 inch SATA300 disk driven 1 x EIDE interface supports on-board

CompactFlash™ socket

Ethernet In ter facesn two interfaces supporting 10/100/1000 Mbps:-è implemented by Intel® 82576EB LAN

Controller via x4 PCI Express® linkè both interfaces accessed via optional P0

(see Note 1)è 1 channel switchable to front panel RJ45

n support for VITA 31.1:-è Gigabit Ethernet for VME64x backplanes

PMC/XMC In ter facesn 2 x PMC/XMC shared sites:-è PMC sites support 32/64-bit, 33/66/100MHz

PCI-X operation è PCI 3.3V or 5V signalingè XMC (Switched Mezzanine Card) sites

support x8 PCI Express® linksè XMC sites powered from 5V supply

n PMC Site 1 I/O via front panel and P2n PMC Site 2 I/O via front panel and optional P0

(see Note 1)n expansion to optional dual PMC carrier board:-è via expansion connector (32-bit/33 MHz)è or via PMC/XMC site 2 (64-bit/66 MHz)

Graphics In ter facen implemented by the integrated chipset

graphics controllern resolutions up to 1920 x 1200 @ 16M colors n analog graphics accessed via front panel

26-way high-density connector or optional P0

Se rial In ter facesn 3 x serial channel interfaces:-è 1 x RS232 accessed via 26-way high density

connector on front panelè 2 x RS232/422/485 accessed via P2

n 16550 compatible UARTs

Other Pe riph eral In ter facesn PC-compatible Real Time Clockn 3 x USB 2.0 interfaces:-è 1 x USB via a 26-way high-density connector

on front panelè 1 x USB via P2 connectorè option for USB via P0 connector (see Note 1)

n keyboard and mouse interfaces accessed via a26-way high-density connector on front panelor optionally via P0 connector

n watchdog timern 1 x 32-bit Long Duration Timer with processor

interrupt capability

Flash EPROMn 8 Mbytes of BIOS Flash EPROMn 64 Mbytes of Application Flash EPROM

Soft ware Sup portn support for Linux®, Windows® 7, Windows®

Embedded Standard 7, Windows® XP, Windows® XP Embedded, Windows® Server 2003,Windows® Server 2008, VxWorks®, QNX®,Solaris™ and LynxOS®

Firm ware Sup portn UEFI-compliant BIOS with legacy mode supportn comprehensive Power-On Self-Test (POST)n LAN boot firmware included

Built-In Test (BIT) Sup port (op tional)n Power-on BIT (PBIT)n Initiated BIT (IBIT)n Continuous BIT (CBIT)


rating of 94V-0

VME In ter facen P1 and P2 connectors compatible with VME64xn implemented using IDT®/Tundra® Tsi148™ devicen VME Master/Slaven A32/A24/A16/D64/D32/D16/D8(EO)/MBLT64n fast hardware byte swappingn auto system controller detectn full interrupter / interrupt handler supportn bus error interrupt hardware

Elec tri cal Spec i fi ca tion n +5V @ 10.2A (typical with 2.53 GHz processor

and 4 Gbytes SDRAM)n [email protected]; [email protected]; 3.3V not requiredn +12V and -12V routed to both PMC/XMC sites

and PMC expansion connector

En vi ron men tal Spec i fi ca tionn operating temperatures:-è 0°C to +55°C (N-Series)è -25°C to +70°C (E-Series: 2.0 GHz or 1.33 GHz)è -40°C to +70°C (K-Series: 2.0 GHz)è -40°C to +85°C (K-Series: 1.33 GHz)

n storage temperature: -40°C to +85°Cn 5% to 95% Relative Humidity, non condensing


n ruggedized versions, see separate datasheets:-è conduction-cooled: VP 717/08x-RCè air-cooled: VP 717/08x-RA

Me chan i cal Spec i fi ca tionn 6U form-factorn single slot, front panel width 0.8-inch (20.3mm)n utilizes 160-way connectors for P1 and P2n optional P0n IEEE 1101.10 handlesn shock: 20g, 11ms, ½ sine n vibration: 5Hz-2000Hz at 2g, 0.38mm peak

displacement

Note 1: The optional P0 connector supportseither PMC Site 2 I/O x64 and 1 x Ethernet orPMC Site 2 I/O x32, SATA, USB and 2 x Ethernet

OR DER ING IN FOR MA TIONOr der Num ber Prod uct De scrip tion (Hard ware) For the or der num ber suf fix (xy) op tions please con tact your lo cal sales of fice:

Where x = P2 and P0 I/O con fig u ra tions Where y = SDRAM size

VP 717/080-xy 1.33 GHz Intel® Core™ i7-660UE pro ces sor x - P2 and P0 I/O con fig u ra tions y - up to 8 Gbytes SDRAMVP 717/082-xy 2.0 GHz Intel® Core™ i7-620LE pro ces sorVP 717/083-xy 2.53 GHz Intel® Core™ i7-610E pro ces sor

For ac ces so ries please con tact your lo cal sales of fice.For ex tended tem per a ture E and K-Se ries, or ruggedized RA and RC-Se ries, please con tact your lo cal sales of fice.


1 x Ethernet10/100/1000Mbps PMC 2PMC 1

PM

C M

od

ule

PC

I-X

100

1 xUSB 2.0

1 xUSB 2.0

VME1 x SATA300

P2PMCI/O

P0PMCI/O

3V

P2 P0P0

1 x RS232

DDR3ECC

DRAM

SPIBIOSFlash

2 x RS232/422/485

ApplicationFlash

= PCI-Express

x8

TundraTsi148

ByteSwap

PM

C M

od

ule

XM

C

2 x Ethernet10/100/1000(VITA 31.1)

1 xVGA

1 xVGA

x2

x4

XM

C

x8

x8

Intel82576

IntelCore i7

SuperI/O

PCIeMUX

PCIe to PCI-XBridge

PCIe to PCI

Bridge

PCIe to PCI-XBridge

PC

I-X

100

PMC Expansion

PCI33

x4

x1

Intel QM57 Express

1 xUSB

SATAto

EIDE

CFTM

SATA300

1 xEIDE

SATAto

EIDE

SA

TA

The AD CR5/PMC Dual PMC Carrier Board can be used

with a range of Concurrent Technologies VME PMC host

processor boards. The carrier board allows two PMC

modules to be added to the host processor board,

thereby increasing the flexibility and functionality of

the host board. Standard PMC modules include SAS,

LAN, WANs, Graphics, Communications and Modems.

Non-monarch mode Processor PMCs (PrPMC) modules

can also be used. For harsher environments, extended

temperature versions are supported. The AD-CR5/PMC

is pin-compatible with the rear I/O of the popular

AD-CR2/PMC Dual PMC Carrier board.

AP PLI CA TIONS

n Supports two single size PMC modules or one double size module

n I/O is available via front panel, P2 backplane connectorand optional P0 backplane connector:- pin mapping combinations are compliant with VITA 35- pin-compatible with the popular AD CR2/PMC

n Up to 128 rear panel I/O lines

n 5V and 3.3V PMC modules are supported

n Standard PCI bus expansion using a PCI to PCI bridge

n Extended temperature versions (E-Series, K-Series):- E: -25°C to +70°C, air-cooled - K: -40°C to +85°C, humidity sealant, air-cooled

n Occupies one VME slot

n For use with a range of Concurrent Technologies VMEPMC host processor boards

n Operating System support depends upon the ConcurrentTechnologies PMC host processor board

HIGHLIGHTS

AD CR5/PMCVME

Dual PMC Car rier Board

N, E, K - Se ries



alastair

RL Emb WWW Bdr


Spec i fi ca tionDual PMC Car rier Boardn support for 2 single width modules or one dual

width module:-è 5 Volt or 3.3 Volt signalingè 32-bit, 33MHz local PCI busè supports dual function modulesè supports non-Monarch Processor PMC modules

n complies with CMC (Common Mezzanine Card)standard IEEE 1386-2001 and PMC (PCI MezzanineCard) standard IEEE 1386.1-2001

n I/O is accessible via the front panel, P2 connector and optional P0 connector:-è 64 or 32+32 I/O signals via P2 connectorè 64 I/O signals via P0 connectorè I/O pin mapping compliant with IEEE 1386 and

with VITA 35 PMC I/O wiring standardsè I/O signals routed as differential pairs

n I/O is user configurable with jumper blocksn I/O is compatible with the popular AD CR2/PMC

Adaptor In ter facen connects to a compatible VME PMC host processor

board:-è implemented using the Pericom PI7C8152A

PCI to PCI bridgeè 32-bit, 33MHz PCI interface

n utilizes PCI 2.2 Local Bus Specificationn utilizes PCI to PCI Bridge Specification 1.1

Com pat i ble VME PMC Host Boardsn Example host processor boards are:-è VP 717/08xè VP 417/03x

Soft ware Supportn adaptor interface features a standard PCI to PCI

bridge:-è PMC modules appear on the additional PCI bus

n Operating System support depends upon theConcurrent Technologies PMC host processor board

Elec tri cal Spec i fi ca tion n +5V @ 0.5A maximum (excluding PMC modules)n +12V @ 0.0A; -12V @ 0.0A; 3.3V not requiredn +12V and -12V routed to both PMC sites

En vi ron men tal Spec i fi ca tionn operating temperatures:-è 0°C to +55°C (N-Series)è -25°C to +70°C (E-Series)è -40°C to +85°C (K-Series)

n storage temperature: -40°C to +85°Cn 5% to 95% Relative Humidity, non condensing


Me chan i cal Spec i fi ca tionn 6U form-factorn single slot, front panel width 0.8-inch (20.3mm)n utilizes 96-way connectors for P1 and P2n optional P0n shock: 20g, 11ms, ½ sine n vibration: 5Hz-2000Hz at 2g, 0.38mm peak

displacement

OR DER ING IN FOR MA TION

Or der Num ber Prod uct De scrip tion (Hard ware)

AD CR5/PMC-00 Dual PMC Car rier Board with out P0 Con nec tor and with VME handlesAD CR5/PMC-01 Dual PMC Car rier Board with P0 Con nec tor and with VME64x han dlesAD CR5/PMC-10 Dual PMC Car rier Board with out P0 Con nec tor and with VME64x han dles

For ex tended tem per a ture, E or K-Se ries, please con tact your lo cal sales of ficeAll com pa nies and prod uct names are trade marks of their re spec tive or ga ni za tions. Datasheet Code 1652/0111Spec i fi ca tion sub ject to change; E and OE. © Con cur rent Tech nol o gies 2011

P2P0 P1

PMC 2

HostProcessor

Board

PMC 2Module

Power

PCI to PCIBridge

Local PCI Bus

I/O ConfigBlock

I/O ConfigBlock

PMC 1Module

PMC 1

Re

ar

I/O

Re

ar

I/O

64

I/O

64

I/O

Rear I/O Con fig u ra tion: VITA 35 P4V0-64 and P4V2-64ac

P2 P1

PMC 2

HostProcessor

Board

PMC 2Module

Power

PCI to PCIBridge

Local PCI Bus

I/O ConfigBlock

I/O ConfigBlock

PMC 1Module

PMC 1

Re

ar

I/O

Re

ar

I/O

32

+3

2 I/O

32 I/O

Rear I/O Con fig u ra tion: IEEE 1386 or VITA 35 P4V2-32+32ac

P2 P1

PMC 2

HostProcessor

Board

PMC 2Module

Power

PCI to PCIBridge

Local PCI Bus

I/O ConfigBlock

I/O ConfigBlock

PMC 1Module

PMC 1

Re

ar

I/O

Re

ar

I/O

64

I/O

Rear I/O Con fig u ra tion: VITA 35 P4V2-64ac

4 Gilberd Court, Colchester, Essex, CO4 9WN, UKTel: +44 (0)1206 752626 Fax: +44 (0)1206 7511163840 Packard Road, Ann Arbor, MI 48108, USATel: (734) 971 6309 Fax: (734) 971 6350

The AD CR3/PMC Carrier Board can be used with a range

of Concurrent Technologies’ PMC host processor boards.

By using a host board PMC site the carrier board allows 2

PMC modules to be added to the host processor board

while still operating at 66 MHz and in 64-bit mode. This

increases the flexibility and I/O capability of the host

board without compromising performance. Standard

PMC slave boards include SCSI, LAN, WANs, Graphics,

Communications and Modems. Non-monarch

processor PMCs (PrPMC) can also be used. Specialized

I/O can be designed and added using the AD CR3/PMC

Carrier Board. An EIDE hard disk drive and Compact

Flash™ Drive are also supported.

APPLICATIONS

� Supports 2 single size PMC modules or 1 double sizemodule:- both PMC sites support 32/64-bit and 33/66 MHz- I/O via front panel and P0 and P2 backplane

connectors- Up to 128 rear panel I/O lines

� For use with selected Concurrent TechnologiesPMC host processor boards

� Extends EIDE interface on selected PMC host processorboards:- allows simultaneous use of on-board disk drive,

Compact Flash and both PMC sites

� Occupies one VME slot

� Extended temperature versions available:- -25°C to +70°C (E-Series)- -40°C to +85°C (K-Series)

� Standard PCI bus expansion using PCI-PCI bridges,compatible with, for example:- Windows® XP- Windows® 2000- Linux®- VxWorks®

HIGHLIGHTS

64-bit 66 MHzDual PMC Carrier Board

RoHS2002/95/EC

alastair

RL Emb WWW Bdr


PMC Interfaces� 2 x PMC sites and for both sites:-� I/O via front panel, via P2 for site 1 and

optionally via P0 for site 2� 32/64-bit and 33/66 MHz PCI operation� 3.3V PCI signaling only

� 64 I/O signals via optional P0 connector� 64 I/O signals via P2 connector� I/O pin mapping compliant with ANSI/VITA

35-2000 P4V0-64 & P4V2-64ac PMC I/O wiringstandards

� carrier provides 3.3V supply� utilizes PCI 3.0 electrical specification� utilizes PCI logical layer specification� complies with CMC (Common Mezzanine Card)

standard (IEEE P1386)

AD CR3/PMC Carrier Interface� connects to the host processor board using

either PMC or XMC adaptor:-� PMC interface at up to 64-bit/66MHz� XMC PCI Express™ (PCI-E) interface at up to

x4 PCI-E� utilizes PMC/XMC site on host board

� carrier uses flexible cable connection witheither PMC or XMC adaptor:-� uses x4 PCI-E cable connection� boards are located in chassis together, then

pushed into backplane separately� easier to insert and eject

Compatible Host Boards� example host processor boards with XMC

interface:-� VX 405/04x

� example host processor boards with PMCinterface:-� VP 347/02x� VP 345/02x� VP 337/02x� VP 335/02x� VP 317/02x� VP 315/02x

EIDE Interface� extends host board's EIDE interface:-� uses host board's EIDE connector

� example host boards with compatible EIDEconnector:-� VP 337/02x� VP 335/02x� VP 317/02x� VP 315/02x

� single channel for up to two devices (masterand slave)� on-board disk drive and CompactFlash

� EIDE interface can be fully used in conjunctionwith both PMC sites

Software Support� carrier features standard PCI-PCI bridge(s):-� PMC modules appear on additional PCI bus

� compatible with various operating systems, forexample VxWorks, Windows XP, Windows 2000or Linux

Environmental Specification� compatible with host boards operating at:-� 0°C to +55°C (N-Series)� -25°C to +70°C (E-Series)� -40°C to +85°C (K-Series)

� 10% to 90% Relative Humiditynon-condensing (operating)� K-Series includes humidity sealant

� -40°C to +85°C (storage)� 10% to 90% Relative Humidity

non-condensing (storage)

Electrical Specification� all voltages to be within �5%� power taken from VME bus P1 connector� 1.2A (maximum) current consumption at +5V� 0.0A current consumption at +12V� 0.0A current consumption at -12V

Mechanical Specification� utilizes a single VME slot� has a VME front panel:-� VME 6U dimensions

� shock:20g, 11ms, ½ sine (operating);30g, 11ms, ½ sine (non-operating)

� vibration:5Hz-2000Hz at 2g, 0.38mm peakdisplacement (operating);5Hz-2000Hz at 5g, 0.76mm peakdisplacement (non-operating)

ORDERING INFORMATION

Order Number Product Description (Hardware)

AD CR3/PMC-0y Dual PMC Carrier Board without P0 Connector and VME handles, for PMC interface Where y = hard disk sizeAD CR3/PMC-1y Dual PMC Carrier Board with P0 Connector and VME64x handles, for PMC interface 0 - typical capacity HDDAD CR3/PMC-2y Dual PMC Carrier Board without P0 Connector and with VME64x handles, for PMC interface 5 - larger capacity HDDAD CR3/PMC-4y Dual PMC Carrier Board with P0 Connector (not VXS) and VME64x handles, for XMC interface 7 - no HDD fittedAD CR3/PMC-5y Dual PMC Carrier Board without P0 Connector and with VME64x handles, for XMC interface

Note: all compatible SBCs are as listed above in the section “Compatible Host Boards”For extended temperature, E or K-Series, and for Hard Disk Drive (HDD) capacity, please contact your local sales office

All companies and product names are trademarks of their respective organizations. Datasheet Code 1480/0906Specification subject to change; E and OE. RoHS 2002/95/EC compliant. © Concurrent Technologies 2006

P2P1

PMC 1

PowerBridge

InterfaceBridge

Interfacex4 PCI-E

CF

TM

PMC 1

PM

CM

od

ule

PMC 2

PM

CM

od

ule

PMCHost

ProcessorBoard

PMCHostEIDE

Connector

Op

tio

na

l

P0

64-bit PCI Bus

AD CR3/PMC

PMC Carrier

PMC Adaptor on

Host Processor Board

AD CR3/PMC Carrier with PMC Interface

P2P1

PMC 1

PowerBridge

InterfacePCI-E

Connectionsx4PCI-E

PMC 1

PM

CM

od

ule

PMC 2

PM

CM

od

ule

XMCHost

ProcessorBoard O

ptio

na

l

P0

64-bit PCI Bus

x4PCI-E

AD CR3/PMC

PMC Carrier

XMC Adaptor on

Host Processor Board

AD CR3/PMC Carrier with XMC Interface


The AD CR2/PMC-U Carrier Board can be used with

several of Concurrent Technologies’ range of VME PMC

host processor boards. The carrier board allows 2 PMC

modules to be added to the host processor board,

thereby increasing the flexibility and functionality of

the host board. Standard PMC slave boards include

SCSI, LAN, WANs, Graphics, Communications and

Modems. Non-monarch processor PMCs (PrPMC) can

also be used. Specialized I/O can be designed and

added using the AD CR2/PMC-U Carrier Board.

APPLICATIONS

� Supports 2 single size PMC modules or 1 double sizemodule

� I/O via front panel and P2 backplane connector andoptional P0 backplane connector

� Up to 128 rear panel I/O lines

� 5V and 3.3V PMC modules supported

� For use with selected Concurrent TechnologiesVME PMC host processor boards

� Occupies one VME slot

� Standard PCI bus expansion using PCI-PCI bridge,compatible with, for example:- VxWorks®- Windows® 2000- Linux®

� Extended temperature versions available:- -25°C to +70°C (E-Series)- -40°C to +85°C (K-Series)

� Operating system depends on the ConcurrentTechnologies PMC host processor board

HIGHLIGHTS

PMC Carrier Board

RoHS2002/95/EC

alastair

RL Emb WWW Bdr


PMC Interfaces� 2 interfaces provided:-� each supports a single size (75mm x 150mm)

PMC module� I/O is accessible via:-� front panel; and/or,� P2 backplane connector; and/or,� P0 backplane connector (optional)

� 64 I/O signals via P0 connector� 64 or 32+32 I/O signals via P2 connector� complies with CMC (Common Mezzanine Card)

standard (IEEE P1386)� I/O pin mapping compliant with

ANSI/VITA 35-2000 PMC I/O wiring standards� I/O user configurable with jumper blocks� logical layer based on PCI protocol specification� electrical layer based on PCI electrical

specification� supports 5V or 3.3V PMC modules� provides 3.3V supply

Adapter Interface� connects to a VME PMC host processor board� utilizes PCI electrical specification� utilizes PCI logical layer specification

Compatible PMC Host Boards� Example host processor boards are:-� VP 347/02x� VP 345/02x� VP 337/02x� VP 335/02x� VP 327/02x� VP 325/02x� VP 317/02x� VP 315/02x� VP 307/01x� VP 305/01x� VP 110/01x� VP 101/01x

Software Support� adapter features a standard PCI-PCI bridge:-� PMC modules appear on the additional PCI bus

� compatible with various operating systems, forexample VxWorks, Windows 2000 or Linux

Electrical Specification� all voltages to be within �5%� power taken from VME bus P1 connector� 0.5A (maximum) current consumption at +5V� 0.0A current consumption at +12V and at -12V

Environmental Specification� compatible with PMC host boards operating at:-� -0°C to +55°C (N-Series)� -25°C to +70°C (E-Series)� -40°C to +85°C (K-Series)

� 10% to 90% Relative Humidity non-condensing(operating):-� K-Series includes humidity sealant

� -40°C to +85°C (storage)� 10% to 90% Relative Humidity non-condensing

(storage)

Mechanical Specification� utilizes a single VME slot� has a VME front panel:-� VME 6U dimensions

� shock:20g, 11ms, ½ sine (operating);30g, 11ms, ½ sine (non-operating)

� vibration:5Hz-2000Hz at 2g, 0.38mm peakdisplacement (operating);5Hz-2000Hz at 5g, 0.76mm peakdisplacement (non-operating)



AD CR2/PMC-00U PMC Carrier Board without P0 ConnectorAD CR2/PMC-01U PMC Carrier Board with P0 Connector and with VME64x handlesAD CR2/PMC-10U PMC Carrier Board without P0 Connector and with VME64x handles

For extended temperature, E or K-Series, please contact your local sales office

All companies and product names are trademarks of their respective organizations. Datasheet Code 1528/0906Specification subject to change; E and OE. © Concurrent Technologies 2006

P2

Op

tio

na

l

P0P1

PMC 1PMC 2

PMCHost

ProcessorBoard

PCIInterface

PowerBridge

Interface

PCIInterface

alastair

RL Emb WWW Bdr





The DS MS1/034-RC is a ruggedized conduction-cooled

VME Mass Storage Module supporting up to two 2.5 inch

SATA300 mass storage drives and a CompactFlash™ site.

The DS MS1/034-RC is designed to work with one or

more Concurrent Technologies VME or VXS single board

computers simultaneously. This conduction-cooled

board is capable of operating in temperatures ranging

from -40°C to +85°C where it is suitable for a range of

applications within the defense, industrial control,

telecomms, telemetry, scientific and aerospace

markets. The board is rear I/O plug compatible with

the commercial air-cooled and the ruggedized

air-cooled versions.

AP PLI CA TIONS

n Ruggedized 6U VME Mass Storage Module:- conduction-cooled to IEEE 1101.2- -40°C to +85°C operating temperature- conformally coated- supports up to two 2.5 inch SATA300 Solid State

Flash drives and a CompactFlash site (Type-I)- operates with one or more Concurrent

Technologies VME or VXS conduction-cooledsingle board computers (SBCs) simultaneously

- interfaces to the SBCs' SATA and USB ports- single slot

n Ruggedized air-cooled version (RA-Series):- -40°C to +75°C, conformally coated- see DS MS1/0x4-RA datasheet

n Commercial air-cooled version:- rear plug compatible with the ruggedized versions- useful for bench development- for use in commercial (non-rugged) applications- see DS MS1/0xx datasheet

HIGHLIGHTS

DS MS1/034-RC

Multi-drive Mass Stor age Mod uleRug ged Con duc tion-Cooled

RC - Se ries

VMERug gedized

alastair

RL Emb WWW Bdr


SpecificationRuggedized Mass Stor age Mod ulen conduction-cooled to IEEE 1101.2 n -40°C to +85°C operating temperaturen conformally coatedn supports up to two 2.5 inch SATA300 Solid State

Flash drives and a CompactFlash™ site (Type-I)n operates with one or more Concurrent

Technologies VME or VXS conduction-cooled singleboard computers (SBCs) simultaneously

n interfaces to the SBCs' SATA and USB ports:-è SATA150 or SATA300 supportedè USB 1.1 and USB 2.0 supported

n ruggedized air-cooled version:-è see DS MS1/0x4-RA datasheet

n non-ruggedized commercial version:-è see DS MS1/0xx datasheet

Com pat i ble VME/VXS SBCsn VME or VXS Single Board Computer (SBC):-è ruggedized conduction cooled versions

n VP 717/08x-RC, Intel® Core™ i7 processorn VX 511/06x-RC, Intel® Core™ 2 Duo processorn VP A45/01x-RC, Intel® Atom processorn contact your local sales office for the latest range

of boards supported

SATA and USB In ter facesn one or more SATA/USB connections can be made

from the SBCs to the DS MS1/034-RC Mass StorageModule:-è up to 2 x SBC SATA drive interfaces connect to

up to two onboard SATA Solid State Flash drivesè 1 x SBC USB port connects to the CompactFlash

site via a USB to EIDE convertorn accessible via P2 connector

Soft ware Sup portn supported operating systems depend on the VME or

VXS Single Board Computer used

Safetyn PCB (PWB) manufactured with flammability rating

of 94V-0

En vi ron men tal Spec i fi ca tionn in conduction-cooled environments specialized

Solid State Flash drives are requiredn operating temperature:-è VITA 47 Class CC4, -40°C to +85°C

n storage temperature:-è VITA 47 Class C4, -55°C to +105°C

n operating and storage altitude:-1,000 to 50,000 feet (-305 to 15,240 meters)

n 5% to 85% Relative Humidity, non condensing (operating/storage)

n ruggedized and commercial air-cooled versions:-è rear plug compatibleè ruggedized air-cooled: DS MS1/0x4-RA è commercial: DS MS1/0xx

Elec tri cal Spec i fi ca tionn requires 5V supply, typical current 0.2A plus:-è maximum 0.3A per Flash drive @5V

n 3.3V, +12V and -12V supplies are not required

Me chan i cal Spec i fi ca tionn 6U form-factorn single slot, front panel width 0.8 inch (20.3mm)n utilizes 160-way connectors for P1 and P2:-è P0 not utilized

n operating mechanical:- è shock - VITA 47 Class OS2, 40g è random vibration - VITA 47 Class V3, 0.1g²/Hz

OR DER ING IN FOR MA TIONOr der Num ber Prod uct De scrip tion (Hard ware) For the or der num ber suf fix (zz) op tions con tact your lo cal sales of fice:

where zz = size of mass stor age drives and num ber of drives fit ted

DS MS1/034-zzRC up to 2 x SATA300 Solid State drives and a CompactFlash site zz - con tact lo cal sales of fice

For com mer cial and ruggedized air-cooled ver sions please con tact your lo cal sales of fice


USB toCompact

Flash

USB SATASATA 5V

CFTM SATA SSD

Power

SATA SSD

DS MS1/034-zzRC up to 2 x SATA drives and a CompactFlash site

(P2) (P2) (P2) (P1)

alastair

RL Emb WWW Bdr





The DS MS1/0xx VME Mass Storage Module supports up

to three 2.5 inch SATA300 mass storage drives or a

CD/DVD RW drive and one 2.5 inch drive. There is also

support for a CompactFlash™ drive. The DS MS1/0xx is

designed to work with one or more Concurrent

Technologies VME or VXS single board computers

simultaneously. The board is capable of operating in

temperatures ranging from -40°C to +85°C where it is

suitable for a range of applications within the

defense, industrial control, telecomms, telemetry,

scientific and aerospace markets. In harsh

environments, or ruggedized versions, Solid State

Flash drives or ruggedized rotating drives are required

and the CD/DVD RW drive is not supported.

AP PLI CA TIONS

n VME Mass Storage Module:- operates with one or more Concurrent

Technologies VME or VXS single board computers(SBCs) simultaneously

- interfaces to the SBCs' SATA and USB portsn Various configurations available:

- one, two or three 2.5 inch SATA300 drives- or one 2.5 inch SATA300 drive and a CD/DVD RW

n Supports a CompactFlash site (Type-I) in anyconfiguration

n Two direct USB port connections from the VME P2connector are routed directly to the front panel

n Extended temperature options also available:- -25°C to +70°C (E-Series)- -40°C to +85°C (K-Series, includes humidity

sealant)- specialized drives are required

n Ruggedized versions:- -40°C to +75°C (RA-Series)- -40°C to +85°C (RC-Series)- conformally coated- Solid State (Flash) drives are required

n In harsh environments the CD/DVD RW driveconfiguration is not supported

n Optional rear transition module provides connectionfrom the SBCs to the Mass Storage Module

HIGHLIGHTS

DS MS1/0xxVME

Multi-drive Mass Stor age Mod ule

N, E, K - Se ries

SD1SM / xx0

sevird 003ATAS x 3 ot pu htiw

DVD/DC dna evird 003ATAS htiw elb aliava osla(

WR) evird

alastair

RL Emb WWW Bdr


SpecificationMass Stor age Mod ulen DS MS1/0xx Mass Storage Module:-è operates with one or more Concurrent

Technologies VME or VXS single boardcomputers (SBCs) simultaneously

è interfaces to the SBCs' SATA and USB portsè SATA150 or SATA300 supportedè USB 1.1 and USB 2.0 supported

n various configurations available:è one, two or three 2.5 inch SATA300 drivesè or one 2.5 inch SATA300 drive and a SATA

CD/DVD RW n supports a CompactFlash site (Type-I) in any

configuration

Com pat i ble VME/VXS SBCsn VME or VXS Single Board Computer (SBC):-è commercial versionsè some versions ruggedized

n VP 717/08x, Intel® Core™ i7 processorn VP A45/01x, Intel® Atom processorn VX 541/06x, Intel® Core™ 2 Duo processorn VX 511/06x, Intel® Core™ 2 Duo processorn VX 407/04x, Intel® Core™ 2 Duo processorn contact your local sales office for the latest

range of boards supported

SATA and USB In ter facesn one or more SBC SATA/USB connections can be

made from the SBC to the DS MS1/0xx MassStorage Module

n 3 x SBC SATA drive interfaces via P2:-è 1 x SBC SATA interface connects to either a

SATA drive or the SATA CD/DVD RW è 2 x SBC SATA interfaces connect to 2 x SATA

drives n 4 x SBC USB ports via P2:-è 1 x SBC USB port connects to the EIDE

CompactFlash™ siteè 1 x SBC USB port connects to either a SATA

drive or the SATA CD/DVD RW (N-Series only)è 2 x USB port connections from the VME P2

connector are routed directly to the frontpanel

n the CB MSS/30p cable interface kit provides:-è connection to the SATA and USB ports on P2è SATA and USB interface cablesè rear transition module for the DS MS1/0xx

Soft ware Sup portn supported operating systems depend on the

VME or VXS single board computer used


rating of 94V-0

En vi ron men tal Spec i fi ca tionn in harsh environments specialized Solid State

Flash drives are required:-è CD/DVD RW drive is not supported

n operating temperatures:-è 0°C to +55°C (N-Series)è -25°C to +70°C (E-Series)è -40°C to +85°C (K-Series)è K-Series includes humidity sealant

n ruggedized versions:-è rear plug compatibleè air-cooled: see DS MS1/0x4-RA datasheetè conduction-cooled: see DS MS1/034-RC

datasheet

Elec tri cal Spec i fi ca tionn requires 5V supply, typical current 0.2A

plus:-è maximum 1.1A per hard disk @ 5Vè maximum 1.5A CD/DVD RW @ 5V

n 3.3V, +12V and -12V supplies are notrequired

Me chan i cal Spec i fi ca tionn 6U form-factorn single slot, front panel width 0.8 inch

(20.3mm)n utilizes 160-way connectors for P1 and P2è compatible with 96-way connectors

OR DER ING IN FOR MA TIONOr der Num ber Prod uct De scrip tion (Hard ware) Re place the or der num ber pa ram e ters with se lec tions from the fol low ing:

Where x = type of front panel han dles Where zz = drive type/size/quantity

DS MS1/0x3-zz CD/DVD RW, SATA drive and a CompactFlash site 0 - VME han dles zz - con tact lo cal sales of ficeDS MS1/0x4-zz up to 3 x SATA drives and a CompactFlash site 1 - VME64 han dles

CB MSS/30p-10 Ca ble In ter face Kit: VME P2 rear tran si tion mod ule in clud ing 3 x SATA ca bles and 4 x USB ca bles

For ca ble in ter face kit 'p' op tions please con tact lo cal sales of ficeFor ex tended tem per a ture and ruggedized ver sions please con tact your lo cal sales of fice


USB toCompact

Flash

2 x USB

USB

4 x USB

USB

2 x SATA

SATA SATA5V

USB toSATA

(N-SeriesOnly)

CFTM

Rear Transition Module (P2)(optional)

DVD/CD-RW

Power

SATA HDD

2 x USB

DS MS1/0x3-zz CD/DVD RW drive, SATA drive and a CompactFlash site

USB toCompact

Flash

CFTM SATA HDD SATA HDD

Power

SATA HDD

DS MS1/0x4-zz up to 3 x SATA drives and a CompactFlash site

USB

4 x USB

USB

3 x SATA

SATA SATA5V

Rear Transition Module (P2)(optional)

2 x USB

2 x USB

USB toSATA

(N-SeriesOnly)

SD1SM / xx0

DVD/DC dna evird 003ATAS htiw

WRevird

)sevird 003ATAS x 3 ot pu htiw elb aliava osla(


The DS MSS/00x-U Mass Storage Module supports up to

two EIDE peripheral devices on a single slot VME board

and an optional floppy disk drive in a dual slot

combination. In addition a front panel connector can

be configured as a parallel or serial port. The parallel

port enables connection to other peripherals, such as a

CD-ROM, Zip® Drive or printer.

The serial port supports either RS232 or RS485/422.

The supported port configuration depends on the VME

processor board to which the DS MSS/00x-U is

connected. The DS MSS/00x-U is designed to interface

with many of Concurrent Technologies' VME bus

processor boards which feature an EIDE interface.

APPLICATIONS

� Supports one 2·5 inch EIDE hard drive

� Support for CompactFlash™ drive or IBM®/HitachiMicrodrive™

� Support for CD-RW/DVD-ROM drive (single slot):- plus support for 3·5 inch floppy disk drive (dual slot)

� Additional front panel connector for:- standard parallel printer interface, or- RS232, or- RS485/422

� Compatible with Concurrent Technologies' VMEprocessor boards

� Supported operating systems depend on the VMEprocessor used

� Single slot solution (without floppy disk drive)

HIGHLIGHTS

Mass Storage Module

RoHS2002/95/EC

alastair

RL Emb WWW Bdr


Mass Storage� supports up to two EIDE devices� select two of the following EIDE options:-� 2·5 inch EIDE Hard Disk Drive� slimline EIDE CD-RW/DVD-ROM� CompactFlash™ Drive or Microdrive

� ATA5 compatible interface

Communication Port� standard 25-way "D"-type, with interface

options for:-� parallel printer or� RS232 or� RS485/422

� option depends on VME processor boardfeatures

� accessed via front panel

Compatible VME Boards� designed to interface to:-� VX 405/04x� VP 347/02x� VP 345/02x� VP 337/02x or VP 337/02x-U� VP 335/02x or -U� VP 327/02x or VP 327/02x-U� VP 325/02x or VP 325/02x-U� VP 317/02x or VP 317/02x-U� VP 315/02x or VP 315/02x-U� VP 307/01x or VP 307/01x-U� VP 305/01x or VP 305/01x-U� VP 110/01x� VP 101/01x

� signal connections via P2 connector

Software Support� depends on the VME processor board

Mechanical Specification� 6U form-factor� single VME slot (without floppy disk drive);

two slots (with floppy disk drive)� utilizes a 96-way DIN connector on P2 for

system interfaces� utilizes a 96-way DIN connector on P1 for

board’s electrical power� typical shock:-

HDD:15g, 11ms, ½ sine (operating);120g, 11ms, ½ sine (non-operating)CD/DVD:0.8g vertical, 1.5g horizontal, 11ms, ½ sine(operating);50g, 11ms, ½ sine (non-operating)FDD:5g, 11ms, ½ sine (operating);80g, 11ms, ½ sine (non-operating)

� typical vibration:-HDD:5Hz-500Hz at 0.67g random, 1g swept sine(operating);5Hz-500Hz at 3g random, 5g swept sine(non-operating)CD/DVD:5Hz-500Hz at 0.25g from 0-peak(operating);10Hz-500Hz at 1g from 0-peak(non-operating)FDD:10Hz-200Hz at 1g (operating);10Hz-100Hz at 2g (non-operating)

Floppy Disk� optional 3.5 inch floppy disk drive (dual slot

versions only):-� accessed via front panel

Electrical Specification� single 5V(±5%) supply requirement� 2.0A (typical, with HDD, CD-ROM and FDD,

the highest power configuration)� power provided from P1 connector

Environmental Specification� 5°C to +55°C (operating)� 10% to 80% Relative Humidity, non

condensing (operating)� -25°C to +65°C (storage)� 10% to 90% Relative Humidity, non

condensing (storage)� storage temperature change rate <20°C/

hour� operating change rate <10°C/ hour



DS MSS/001-xyU Mass Storage Module with Device/Connector Options : 1 slotDS MSS/002-xyU Mass Storage Module with Floppy Disk Drive and Device/Connector Options : 2 slotsDS MSS/01z-xyU Fitted with VME64x handles, where z = 1 or 2

Device Options: select two storage devices : EIDE Hard Disk Drive, EIDE CD-RW/DVD-ROM or EIDE CompactFlashConnector Options: select one front panel connector : printer, RS232 or RS485/422 (depends on VME processor board)

For details of all xy options/combinations available please contact your local sales office

All companies and product names are trademarks of their respective organizations. Datasheet Code 1527/0906Specification subject to change; E and OE. RoHS 2002/95/EC compliant. © Concurrent Technologies 2006

P1 P2

To VME processor board

Parallel orRS232 or

RS485/RS422

FloppyDiskDrive

EIDEHDD

EIDECompactFlashor Microdrive

CD-RW/DVD-ROM

Drive

Powerfor

Drives

op

tion

al

op

tion

al (

SB

Cd

ep

en

de

nt)

op

tion

al

op

tion

al

op

tion

al

EID

EIn

terf

ace

Example combination of DS MSS/0

01-U and VP 305/01x-U

VME VP A45/ 01x-RC Ruggedized Rx - Se riesredlinx.co.za/PDF/CCT_vme.pdf · nauto system controller...

Documents

Transcript of VME VP A45/ 01x-RC Ruggedized Rx - Se riesredlinx.co.za/PDF/CCT_vme.pdf · nauto system controller...