Vintage Decoupage Ornaments -...
3
Enjoy • Create • Celebrate Christmas Vintage Decoupage Ornaments Created by Jo-Ann Fabric and Craft Stores ® Please read and follow all manufacturers’ instructions for all tools and materials used. Provide adult supervision if children participate in this project. ©2012 Jo-Ann Stores, Inc. 213-325 Read through the directions before starting & use the photo as a guide. Directions: 1. Apply a thin layer of Mod Podge ® to the front of wood shape. 2. Position the provided ornament design of choice onto the front of the wood. Allow to dry. 3. Lay the ornament face down on cutting mat and trim around the outside of the wood with an X-Acto ® knife to remove excess paper. 4. Apply a thin coat of Mod Podge ® to the front of the ornament, covering the decorative paper. Repeat if additional coats are needed. Allow to dry. 5. Apply Mod Podge ® to the outer edge of the ornament with a foam brush. 6. Working over a paper plate, sprinkle glitter onto the edges of the ornament where the Mod Podge ® was applied. Set aside to let the glitter dry. 7. Once the Mod Podge ® is completely dry, add a ribbon to the ornament for hanging. If there is no hole at the top, glue the knot of the ribbon on the back of the ornament with hot glue. Skill Level 2: Some experience necessary Approximate Crafting Time: 3-5 hours Supplies & Tools: • Ready-to-finish wood shapes for ornament base • Ribbon • Mod Podge ® decoupage sealer • Foam brush • Scrapbook paper • Gold glitter • X-Acto ® knife • Cutting mat • Paper plate • Hot glue (Note: use only if wood shape does not have a hole) • Provided ornament designs printed out on paper
Transcript of Vintage Decoupage Ornaments -...
Enjoy • Create • Celebrate
Christmas
Vintage Decoupage OrnamentsCreated by Jo-Ann Fabric and Craft Stores®
Please read and follow all manufacturers’ instructions for all tools and materials used.Provide adult supervision if children participate in this project. ©2012 Jo-Ann Stores, Inc. 213-325
Read through the directions before starting & use the photo as a guide.
Directions:
1. Apply a thin layer of Mod Podge® to the front of wood shape.
2. Position the provided ornament design of choice onto the front of the wood. Allow to dry.
3. Lay the ornament face down on cutting mat and trim around the outside of the wood with an X-Acto® knife to remove excess paper.
4. Apply a thin coat of Mod Podge® to the front of the ornament, covering the decorative paper. Repeat if additional coats are needed. Allow to dry.
5. Apply Mod Podge® to the outer edge of the ornament with a foam brush.
6. Working over a paper plate, sprinkle glitter onto the edges of the ornament where the Mod Podge® was applied. Set aside to let the glitter dry.
7. Once the Mod Podge® is completely dry, add a ribbon to the ornament for hanging. If there is no hole at the top, glue the knot of the ribbon on the back of the ornament with hot glue.
Skill Level 2: Some experience necessary
Approximate Crafting Time: 3-5 hours
Supplies & Tools:
• Ready-to-finish wood shapes for ornament base • Ribbon• Mod Podge® decoupage sealer• Foam brush• Scrapbook paper• Gold glitter• X-Acto® knife• Cutting mat• Paper plate• Hot glue (Note: use only if wood shape does not
have a hole)• Provided ornament designs printed out on paper
Enjoy • Create • Celebrate
Christmas
Please read and follow all manufacturers’ instructions for all tools and materials used.Provide adult supervision if children participate in this project. ©2012 Jo-Ann Stores, Inc. 213-325
Continued from previous page.
Enjoy • Create • Celebrate
Christmas
Please read and follow all manufacturers’ instructions for all tools and materials used.Provide adult supervision if children participate in this project. ©2012 Jo-Ann Stores, Inc. 213-325
Continued from previous page.
