VFL Visual Fault Locator for NORTH AMERICA MODULE
2
3330 Earhart Drive, Suite 208 | Carrollton, TX 75006 | Office: 972.556.0916 | Fax: 972.910.8384 | uclswiftna.com NORTH AMERICA VFL MODULE Visual Fault Locator for SWIFT KF4A Fusion Splicer BENEFITS AND FEATURES Internally-installed and powered 650 nanometer red laser provides VFL capability VFL is Visual Fault Locator, allowing a visual check of the splicer to check the quality Inserting the ferrule of the connector (2.5 mm comes standard) into the VFL port when active allows red laser VFL source to be projected through the connector ferrule into the fiber. A failure point (i.e. break) will allow the light to “leak” out and show as a red-highlighted area The VFL has a 2.5mm interface, and can operate in continuous or pulse mode. The VFL can be activated through an easy shortcut key on the KF4A control panel.Perfect Solution with Swift KF4A and Swift Connector EASY UPGRADE An Easy Upgrade for your KF4A Fusion Splicer KF4A The Visual Fault Locator (VFL) utilizes a 650nm red laser to locate and visibly display any failure points throughout the cable. The ferrule is inserted into the VFL port while it’s active and the red laser is projected through the connector ferrule into the fiber, highlighting any faulty areas in a bright red. OVERVIEW
Transcript of VFL Visual Fault Locator for NORTH AMERICA MODULE
3330 Earhart Drive, Suite 208 | Carrollton, TX 75006 | Office: 972.556.0916 | Fax: 972.910.8384 | uclswiftna.com
NORTH AMERICAVFL
MODULEVisual Fault Locator for SWIFT KF4A Fusion Splicer
BENEFITS AND FEATURES
Internally-installed and powered 650 nanometer red laser provides VFL capability
VFL is Visual Fault Locator, allowing a visual check of the splicer to check the quality
Inserting the ferrule of the connector (2.5 mm comes standard) into the VFL port when active allows red laser VFL source to be projected through the connector ferrule into the fiber. A failure point (i.e. break) will allow the light to “leak” out and show as a red-highlighted area
The VFL has a 2.5mm interface, and can operate in continuous or pulse mode. The VFL can be activated through an easy shortcut key on the KF4A control panel.Perfect Solution with Swift KF4A and Swift Connector
EASY UPGRADEAn Easy Upgrade for your KF4A Fusion Splicer
KF4A
The Visual Fault Locator (VFL) utilizes a 650nm red laser to locate and visibly display any failure points throughout the cable. The ferrule is inserted into the VFL port while it’s active and the red laser is projected through the connector ferrule into the fiber, highlighting any faulty areas in a bright red.
OVERVIEW
ITEM
Detector Type
Application
Usage
Fiber
Wavelengths
Interface
Display
Powered By
Operating Temp.
Indium Gallium Arsenide
CATV, FTTH (GPON & BPON)
Measure signal power
Singlemode
1310, 1490 and 1550nm
2.5mm ferrule (SC, FC, ST)
Measures in dBm or mw
KF4A internal systems
-10~ + 60ºC
DESCRIPTIONPOWER METER (PM)
3330 Earhart Drive, Suite 208 | Carrollton, TX 75006 | Office: 972.556.0916 | Fax: 972.910.8384 | uclswiftna.com
NORTH AMERICA
VFL &POWERMETER
Visual Fault Locator/Power Meter
ITEM
Type
Application
Usage
Fiber
Interface
Output
Operating Temp.
650nm class 2 red laser
Telecom and CATV
Find breaks, faults and bends
Singlemode and multimode
2.5mm ferrule (SC, FC, ST)
Continuous or pluse
-10~ + 60ºC
DESCRIPTIONVISUAL FAULT LOCATOR (VFL)
INSTALL NOWON YOUR KF4A
