VESTA-AR MV Metal Clad Arc Resistant Switchgear Datasheets 2014.pdf · magnetically actuated...
Transcript of VESTA-AR MV Metal Clad Arc Resistant Switchgear Datasheets 2014.pdf · magnetically actuated...
VESTA-AR™ medium voltage metal clad arc resistant switchgear with magnetically actuated circuit breaker technology is designed to meet the needs of customers who demand the highest quality power distribution assembly with the smallest footprint (24” x 96” x 60”).
VESTA-AR fulfills the requirement for a switchgear assembly that makes efficient use of available floor space and minimizes the time required for inspection, repair and maintenance of equipment. IEM’s arc resistant technology ensures a safe and reliable solution for maintenance personnel and facility in the event of an arc flash.
IEM Metal-Clad Arc Resistant Switchgear•Voltage 5-15kV; 95kV BIL
•Ampacity 600A – 1200A; 31.5kA
•Dimensions / 1200A: 24” x 96” x 60”
•Dimensions / 2000A: 30” x 96” x 72”
•Magnetically actuated breaker—up to 100,000 operations
•Full front accessibility
•Draw out breaker, PT & CPT
•Front accessible 600V CT’s and front connected cables
•Shortest breaker pole spacing between phases
• Infrared viewing ports
•Front and rear viewing windows
•Epoxy insulated bus bar configuration optimized for maximum heat dissipation
•Plenum design incorporated into structural configuration—No additional height requirement
•UL & cUL Listed; Type 2A and 2B in accordance with ANSI/IEEE standards
VESTA-AR
MV Metal Clad Arc Resistant Switchgear
Smallest footprint
Magnetically actuated VM1 circuit breaker technology
Front Accessibility
Rear Viewing Windows
Infrared (IR) Viewing Ports (Optional)
Insulated Bus Bar System
Indoor and Outdoor Applications
UL Listed; Meets ANSI, IEEE, and NEMA Standards
Patents Pending
IEM Product
Front Accessibility
Full front accessibility for cable connections and current transformers (CT); this design feature ensures ease of maintenance, minimal usage of floor space and creates a safe environment.
Magnetically Actuated Breaker
Magnetically actuated breakers operate up to 100,000 times without maintenance. These breakers feature far fewer parts and much simpler construction and are among the most reliable in the industry.
Rear Viewing Windows
Larger viewing casement allows complete access to viewing of the bus bar compartment for maintenance to assess any signs of overheating of the bus.
Infrared (IR) Viewing Ports (Optional)
Front and rear infrared viewing ports allow maintenance personnel to easily access thermal monitoring of the equipment without having to open the enclosure.
Insulated Bus Bar System
Medium Voltage insulating and support system with specialty designed structure for current transformers (CT’s). Epoxy insulated bus as standard.
Testing
Rigorous testing shows fully reinforced and sealed joints, hinges and latches, which reduce the risk of damage to maintenance personnel and other existing equipment in the event of an arc flash.
Technical Specifications
UL & cUL Listed, Meets or exceeds type 2A and 2B in accordance with ANSI/IEEE 37.20.7. Multiple configurations available.
IEM Product: Metal-Clad Medium Voltage Switchgear
A
B
C
D
E1
2
3
4
5
7
8
9
10
11
12 22
13
14
15
16
17
18
19
20
21
6
A Low-voltage compartment
B Mid compartment
C Central compartment
D Bottom compartment
E Exhaust compartment
1 Wire-way
2 Low-voltage door
3 Breaker plug connector
4 Mid compartment door
5 Viewing window - front
6 Door Handle
7 Medium-voltage breaker
8 Circuit breaker racking hole
9 Bottom compartment door
10 Infrared viewing window
11 Cables
12 Base
13 Exhaust plenum
14 Back door
15 Epoxy insulated busbars
16 Viewing window - back
17 Current transformers
18 Standoff insulators
19 High-voltage cable
20 Bus boots
21 Surge arrestors
22 Grounding busbar
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.comCorporate Office Vancouver Office
Industrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Industrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
Jacksonville Office
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. VESTA-AR.DS.v1
IEM panelboards are designed to meet the needs of any electrical distribution system. Lighting, Distribution, and Receptacle Panelboards can be custom engineered featuring leading manufacturer’s components and state-of-the-art surge suppression equipment. Standard panelboard configurations are also available.
PIE PanelboardFeatures/Benefits•Voltage: Up to 600Vac, 250Vdc maximum
•Ampacity: 250A to 600A
•65kA at 480V maximum
•UL or CSA listed
•Single phase and three phase
•Series ratings with upstream devices
•Main breaker, main lugs, subfed breaker – optional
•10K thru 65K SCCR (AIC) – interrupting capacity
•Vertically mounted main and sub-feed circuit breakers
•Up to 84 circuits in one panel
• Interiors available in plated copper or aluminum bus
•Complete line of UL listed interiors with 200% rated neutrals for non-linear loads
•Surge Suppression Equipment/Optional integrated TVSS
•Configured for sequence phase connections allowing complete flexible circuit arrangement (1-, 2- or 3-poles) to properly balance the electrical load on each phase
•Lock and door opening mechanism includes a positive slide catch and right- or left-hand installation
•Multi section boards – bolted together and bush openings (horizontal and vertical)
•Standard or door in door trims
•ANSI 61 light gray standard finish, other colors available as option
•Stainless steel and aluminum available
IEM Panelboards
Full Customization and Design Flexibility
New 65K AIC/480V UL Rating for PIE (E Frame) Versions
New 84 Circuit Designs in UL Heat Rise Testing complete
New Emergency (Fuse/Breaker) Panels in Final UL Heat Rise Testing complete
Beginning conceptual design for new “universal” power panel
Seismic shake table testing completed – fully qualified to worst case response spectrum.
IEM ProductIEM Product
IEM Product: Panelboards
CDP PanelboardsFeatures/Benefits•Voltage: Up to 600Vac, 250Vdc Maximum
•Ampacity: 250A to 1200A
•UL or CSA listed
•Single phase and three-phase
•10K thru 200K SCCR (AIC) – Interrupting Capacity (100kA at 480V, 200kA at 240V)
•Series ratings with upstream devices
• Interiors available in plated copper or aluminum bus
•Main breaker or main lugs
•Fully rated or series rated
•Selection includes most commercially available molded case circuit breakers from industry leading manufacturers
•Standard or door in door trims
•ANSI 61 light gray standard finish, other colors available as option
•Stainless steel and aluminum available
IEM DifferenceSuperior Enclosures – All equipment enclosures are designed for specific application and dimensional flexibility.
All enclosures are finished using a state of the art powder coating system providing an indoor finish that exceeds the 1500 hour salt spray testing requirement for outdoor equipment to 3000 hours.
Technical SpecificationsIEM Panelboards meets UL 67, UL 50, CSA and NEMA PB-1 standards and complies with federal specifications WP- 115a
Distribution panelboards meet seismic testing, circuit requirements as outlined by IEEE344 and ICC-ES-AC156
PIU PanelboardsFeatures/Benefits•Voltage: Up to 600Vac, 250Vdc maximum
•Ampacity: 250A to 400A
•14kA at 480V
•65kA at 240V
•UL or CSA listed
•Single phase and three phase
•Main breaker, main lugs, subfed breaker – optional
•10K thru 65K SCCR (AIC) – interrupting capacity
•Vertically mounted main and sub-feed circuit breakers
•Up to 84 circuits in one panel
• Interiors available in plated copper or aluminum bus
•An interior accepts bolt-on or plug-on branch circuit breakers
•Complete line of UL listed interiors with 200% rated neutrals for non-linear loads
•Surge suppression equipment/optional integrated TVSS
•Configured for sequence phase connections allowing complete flexible circuit arrangement (1-, 2- or 3-poles) to properly balance the electrical load on each phase.
•Lock and Door opening mechanism includes a positive slide catch and right- or left-hand installation.
•Multi section boards – bolted together and bush openings (horizontal and vertical)
•Standard or door in door trims
•ANSI 61 light gray standard finish, other colors available as option
•Stainless steel and aluminum available
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. 1.Panelboards_DS.v4
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.com
Industrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Vancouver OfficeCorporate Office
Industrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
Jacksonville Office
Switchboards can be custom designed or utilize a standard configuration to meet specific dimensional and electrical requirements. They can include fully integrated component options from leading manufacturers, including automatic transfer switches, TVSS, distribution transformers, and PLC or relay based transfer schemes. Circuit breakers and fusible switches can be group or individually mounted. Indoor and outdoor enclosures are available in a wide range of durable color finishes.
Features/Benefits•Voltage - Up to 600Vac, Up to 250Vdc maximum
•Ampacity - 400A to 12,000A maximum bus rating
•65 kAIC standard bus bracing (100 or 200kAIC - optional)
•Switchboard ratings through 12,000A, 200kAIC up to 480V, 100kAIC up to 600V
•Type 1 or 3R NEMA enclosures
•Paint ANSI 61 – Standard, other colors available as option
•Front, rear, and side accessibility
•Devices can be individually (vertically) or group (panel/horizontally) mounted
•Custom sheet metal and bus flexibility for busway and transformer connections
•Extensive protective device accessories available
•Silver-plated copper bus, tin-plated copper bus or tin-plated aluminum bus
•1000A per sq in. fully rated copper bus systems
•750A per sq in. fully rated aluminum bus systems
•Tested to short circuit rating of 3 cycles (.05sec.) or to immediate trip of tested OCPD or braced to UL configuration standards
•Rigid frame construction isolating bus and breaker assemblies from enclosure
•Metering compartments built to applicable Utility’s standards
•Variety of fully integrated component options available including automatic transfer switches, TVSS, distribution transformers, and PLC or relay based transfer schemes
IEM Low Voltage Switchboards
Full Customization and Design Flexibility
Component and Metering Selection Options
Fully Rated Bus Based on Density Ratings
Seismic Tested to Worst Case Response Spectrum
Indoor and Outdoor Applications
UL or CSA Listed; Meets ANSI, IEEE, and NEMA Standards
IEM ProductIEM Product
•Front accessible line connections for main device
•Front accessible load connections for feeder devices
•Switchboard fed by cables, cable bus, bus duct, or transformer
•Thermal-magnetic, electronic fixed mounted circuit breaker mains and feeders, Fix-mounted fusible switch mains and feeders or combination of fixed mounted breakers and fusible switches
•Main and branch devices in single section configurations
•Thermal magnetic, electronic circuit breakers with standard, high kAIC or current limiting capability, 80% or 100% rated
•All commercially available options on circuit breakers and fusible switches
IEM DifferenceFully rated bus is based on density ratings, not UL heat rise tests, resulting in more bus and lower operating temperatures.
All enclosures are designed for specific application with improved dimensional flexibility and finished using state of the art powder coating system providing an indoor finish that exceeds the 1500 hour salt spray testing requirement for outdoor equipment to 3000 hours.
Component and metering selections are based on value engineering for the application and optimized to meet specifications.
Recent DevelopmentsUL 200K AIC ratings at 480V through 12,000A with suitably rated components
UL 100K AIC at 600V from 3000A to 12,000A ratings with suitably rated components
UL 100K AIC ratings for commercial metering with suitably rated MCCB
Seismic testing completed – fully qualified to worst case response spectrum
Technical SpecificationsIEM Switchboards meet or exceed applicable industry standards, including UL891, CSA, NEMA standards PB-2, NEMA 1 and NEMA 3R enclosures. Uses UL489 or UL1066 listed breakers.
IEM Distribution Switchboards meet seismic testing, circuit requirements as outlined by IEEE344 and ICC-ES-AC156.
IEM Product: Low Voltage Switchboards
Features/Benefits (cont’d)
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. 2.Switchboards_DS.v4
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.comCorporate Office Jacksonville OfficeVancouver OfficeIndustrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Industrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
IEM’s unique approach to engineering and manufacturing allows us to assemble products that meet specialized dimensional and electrical requirements.
Our flexible capabilities allow for the selection of industry leading components including control and measuring devices, allowing for a superior, fully customizable control and monitoring electrical assembly. This is just one element of IEM’s superior control solutions to provide protection and operational reliability for any quality power distribution assembly.
Depending on the users’ technical and physical requirements, UL 1066 power circuit breakers can be mounted in a fixed or drawout configuration. Indoor, outdoor non walk-in enclosures are available in an extensive selection of durable color finishes.
Features/Benefits•Voltage: up to 600V; Ampacity: up to 5000A
•UL 1066 Circuit Breaker; or CSA
•Through the door breaker operation
•Front accessibility to control and communication wiring
• Isolated access to all wiring
•All breakers have unique drawout design allowing for through-the-door racking
•Short-circuit rating 125kA / 100kA (600V)
•Short-time withstand rating up to 100kA / 85kA (600V)
•Bolted copper bus provided as standard
•Large rear cable compartment pull area allowing maximum room for power cables
•Bus provision for future equipment expansion
IEM Low Voltage Power Circuit Breaker Switchgear
Full Customization and Design Flexibility
Component and Metering Selection Flexibility
Bus Based on Density Ratings
Seismic Tested to Worst Case Response Spectrum
Indoor and Outdoor Applications
UL or CSA Listed; Meets ANSI, IEEE, and NEMA Standards
IEM ProductIEM Product
Features/Benefits (cont’d) •System designed for maximum uptime with low maintenance
•Modular circuit breaker designed for easy addition of control accessories
•Circuit breakers are available in various levels of interrupting ratings from 42–200kA at 480V and 130kA at 600V
•Circuit breaker is available in an 800A frame size and 42kA at 480V interrupting rating
•Up to 4 circuit breakers can be mounted in a 30-inch wide section (up to 1200A)
•Circuit breakers of like frame sizes and interrupting ratings are interchangeable
•Available in NEMA 3R outdoor enclosures
IEM DifferenceAll enclosures are designed for specific application with improved dimensional flexibility and finished using state of the art powder coating system providing an indoor finish that exceeds the 1500 hour salt spray testing requirement for outdoor equipment to 3000 hours.
Component and metering selections are based on value engineering for the application and optimized to meet specifications.
Recent DevelopmentsSeismic testing completed – fully qualified to worst-case response spectrum.
Technical SpecificationsIEM Low Voltage Switchgear meets or exceeds applicable standards including ANSI C37.20.1.
IEM Low Voltage Switchgear meets seismic testing, circuit requirements as outlined by IEEE344 and ICC-ES-AC156.
IEM Product: Low Voltage Switchgear
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. LVSwtchgr_DS.v5.1
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.comCorporate OfficeIndustrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Vancouver Office Jacksonville OfficeIndustrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
Vacuum Circuit Breakers
IEM’s vacuum circuit breaker product line is available in the 5kV, 15kV, and 27kV classes in outdoor non-walk-in, outdoor walk-in and indoor enclosures. Optional component selection including different choices for protective relays, metering devices and circuit breakers for specific applications. This customizable feature makes IEM an ideal choice for unique projects and for matching or upgrading existing installations.
IEM Metal-Clad Switchgear (Circuit Breaker Assemblies)•Voltage 2400V – 27kV
•Ampacity 600A – 3000A
•Optimal component selection includes any commercially available vacuum circuit breaker from industry leading manufacturers
•Rear access for load and incoming connections
•Compartmentalized construction with breaker compartment for each device
•One-high or two-high construction
•Unit substation primaries
• Indoor or Outdoor applications
Metal-Clad Medium Voltage Switchgear
Full Customization and Design Flexibility
Component and Metering Selection Options
Fully Rated Bus Based on Density Ratings
Standard Mechanical Circuit Breakers
Magnetically Actuated Circuit Breakers
Seismic Tested to Worst Case Response Spectrum
Indoor and Outdoor Applications
UL or CSA Listed; Meets ANSI, IEEE, and NEMA Standards
IEM ProductIEM Product
5kV
Nominal Voltage Nominal 3-phaseclass (MVA)
Continuous Current Short Circuit Current Rating
Power Withstand Frequency
BIL Crest Impulse Voltage (kV)
Momentary Close & Latch
Rated Interrupting Time (cycle/ms)
Maximum Symmetrical Interrupting Capability
Short Time Current 3 Sec Carrying Capability(kA)
4.16 250 1200, 2000, 3000 29 19 60 58 5 / 50 36 36
4.16 350 1200, 2000, 3000 41 19 60 78 5 / 50 49 49
4.16 450 1200, 2000, 3000 63 19 60 101 5 / 50 63 63
15kV
Nominal Voltage Nominal 3-phaseclass (MVA)
Continuous Current Short Circuit Current Rating
Power Withstand Frequency
BIL Crest Impulse Voltage (kV)
Momentary Close & Latch
Rated Interrupting Time (cycle/ms)
Maximum Symmetrical Interrupting Capability
Short Time Current 3 Sec Carrying Capability(kA)
13.8 500 1200, 2000, 3000 18 36 95 37 5 / 50 23 23
13.8 750 1200, 2000, 3000 28 36 95 58 5 / 50 36 36
13.8 1000 1200, 2000, 3000 37 36 95 77 5 / 50 48 48
IEM DifferenceFully rated bus is based on density ratings, not UL heat rise tests, resulting in more bus and lower operating temperatures.
All enclosures are designed for specific application with improved dimensional flexibility and finished using state of the art powder coating system providing an indoor finish that exceeds the 1500 hour salt spray testing requirement for outdoor equipment to 3000 hours.
Component and metering selections are based on value engineering for the application and optimized to meet specifications.
Recent DevelopmentsSeismic testing completed – fully qualified to worst case response spectrum.
Technical SpecificationsIEM Switchgear meets or exceeds all ANSI, IEEE, and NEMA standards applicable to metal clad switchgear including C37.20, C37.20.2, C37.20.3, C37.55, C37.57, and NEMA SG-4.
IEM Switchgear meets seismic testing, circuit requirements as outlined by IEEE344 and ICC-ES-AC156.
NEMA 1 and 3R
IEM Medium Voltage Component Selection Ratings
IEM Product: Metal-Clad Medium Voltage Switchgear
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. 4.1.MVSwtchgr_MetalClad.DS.v8
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.comCorporate Office
Industrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Industrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
Jacksonville OfficeVancouver Office
Fusible Load Interrupters
IEM’s fusible load interrupter product line is available in the 5kV, 15kV, and 27kV classes in outdoor non-walk-in, outdoor walk-in and indoor enclosures. IEM metal enclosed switchgear utilizes a compartmentalized construction isolating the bus, cable, and main switches and allowing for minimal maintenance and use of interior barriers.
Metal-enclosed switchgear can be configured to meet unique physical and electrical requirements.
IEM Metal-Enclosed Switchgear (Fusible Load Interrupters)•Voltage 2400V – 27kV
•Ampacity 600A – 3000A
•Rear access for load and incoming connections
•Front connections when required
•Single phase load protection when required
•Arranged to metal clad configuration if applicable
•Compartmentalized construction including utility metering for most U.S. utilities
•Unit substation primaries
• Indoor or outdoor application
Metal-Enclosed Medium Voltage Switchgear
Full Customization and Design Flexibility
Component & Metering Selection Options
Cost-effective Option Provides Safe, Dependable Switching and Fault Protection
Seismic Tested to Worst Case Response Spectrum
Indoor and Outdoor Applications
UL or CSA Listed; Meets ANSI, IEEE, and NEMA Standards
IEM ProductIEM Product
IEM DifferenceAll enclosures are designed for specific application with improved dimensional flexibility and finished using state of the art powder coating system providing an indoor finish that exceeds the 1500 hour salt spray testing requirement for outdoor equipment to 3000 hours.
Component and metering selections are based on value engineering for the application and optimized to meet specifications.
Recent DevelopmentsSeismic testing completed – fully qualified to worst case response spectrum.
Technical Specifications
IEM Switchgear meets or exceeds all ANSI, IEEE, and NEMA standards applicable to metal-enclosed switchgear including C37.20, C37.20.2, C37.20.3, C37.55, C37.57, and NEMA SG-4.
IEM Switchgear meets seismic testing, circuit requirements as outlined by IEEE344 and ICC-ES-AC156.NEMA 1 and 3R enclosures
IEM Product: Metal-Enclosed Medium Voltage Switchgear
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. 4.2MetalEnclSwitchgear_DS.v3
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.comCorporate Office
Industrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Vancouver Office
Industrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
Jacksonville Office
IEM Paralleling Switchgear and Control Systems are designed and manufactured to deliver full control of custom-configured power generation systems. They integrate all facets of metering, protection, communication and controls to deliver peak performance, system reliability and operating economy.
IEM’s experience with generators and voltage regulators from all major North American manufacturers, governor systems for prime movers, and proprietary engine controllers results in efficient and innovative parallel switchgear designs for redundant power applications.
Types of Configured Power Systems•Prime Power – where generators are the only source or main source of power as in island-mode, marine, remote site or military type applications.
•Standby – where the generators serve as back-up to the main (utility) source, commonly installed in hospitals, airport, data centers, waste-water/water treatment facilities, including most life-safety institutional applications.
•Distributed Generation Systems – where generators are applied to supplement the main source (as in peak shave applications) and may also act as the standby system as well.
Paralleling Switchgear And Control Systems
Full Customization and Design Flexibility
Component and Metering Selection Flexibility
Fully Rated Bus Based on Density Ratings
Operator interface touch-screen terminals (OIT)/Human Machine Interface (HMI)
Seismic Tested to Worst Case Response Spectrum
Indoor and Outdoor Applications
UL or CSA Listed; Meets ANSI, IEEE, and NEMA Standards
IEM ProductIEM Product
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. 6.PrllngSwitchgear_DS.v3
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Intrinsic System Features •Load priority control where loads are applied from a pre-determined sequence, highest to lowest priority, based on system capacity and characteristics.
•Generator operational control where only the pre-determined number of generators are asked to start and carry load, either in a scramble or preset start-sequence.
•Operator interface touch-screen terminals (OIT)/Human Machine Interface (HMI) where system controls and interrogation can be accomplished at the switchgear or from a remote network/PC/PLC.
•Remote communications in the most common industry protocols like modbus/canbus and being fully conversant with industry leading Ethernet/interface modules, comm-ports and RS 485 type connections.
•Utility paralleling system designs in passive closed transition (waiting for the sources to become synchronized in voltage, frequency and phase angle), active closed transition (where synchronization is dynamically controlled), soft load or continuous base loading systems.
IEM DifferenceFully rated bus is based on density ratings, not UL heat rise tests, resulting in more bus and lower operating temperatures.
All enclosures are designed for specific application with improved dimensional flexibility and finished using state of the art powder coating system providing an indoor finish that exceeds the 1500 hour salt spray testing requirement for outdoor equipment to 3000 hours.
Wide range of component selection including breakers, meters, relays.
Component and metering selections are based on value engineering for the application and optimized to meet specifications.
Recent DevelopmentsSeismic testing completed – fully qualified to worst case response spectrum.
Technical SpecificationsIEM Switchgear meets seismic testing, circuit requirements as outlined by IEEE344 and ICC-ES-AC156.
IEM Product: Paralleling Switchgear
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.comCorporate Office Vancouver Office
Industrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Industrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
Jacksonville Office
IEM’s medium voltage product line is now available in the 38kV class in indoor, outdoor non-walk-in, and outdoor enclosures.
The 38kV mechanically complete switchgear rated for 40kA is also available with CSA listing when required and applicable, and meets also the seismic requirements of the UBC code.
Features/Benefits•Voltage: 38kV
•Ampacity: 1200A, 2000A
•Basic Insulation Level (BIL): 150kV
•Breaker interrupter ratings: Up to 40kV
•NEMA 1: 42” W x 123” D x 95” H
•NEMA 3R: 42” W x 132” D x 107” H
•Advanced vacuum circuit breaker
•Compartmentalized construction with breaker compartment for each device
•Breaker & PT can be constructed into one section (feeder only)
•Main-tie-main automatic transfer scheme
•Rear access for load and incoming connections
• Indoor or outdoor applications
38kV Metal-CladMedium Voltage Switchgear
ANSI/IEEE C37.20.2 Metal-Clad Switchgear
ANSI/IEEE C37.04 Rating Structure for High Voltage Circuit Breakers
ANSI/IEEE C37.54 Indoor HV Breakers in Metal Enclosure Conformance Test
ANSI/IEEE C37.55 Medium Voltage Metal-Clad Assemblies
ANSI/IEEE C37.09 Test Procedure for AC HV Breakers on Sym Current basis
CSA Listed
IEM IEM
IEM Product: 38kV Metal-Clad Medium Voltage Switchgear
• FullRollonthefloor–Noaccessoriesrequired(Lifttruck,ramp,etc.)
• Manualandelectrical(motor)springcharging
• FrontOperationandfrontaccesstooperatingmechanism
• ACorDCauxiliaryvoltage
• Undervoltagereleaseandsecondshunttripoptional
• Capacitortripdevice–externalwhenACrequired
• Standardfastinterruption:3Cycles
• SIS–600Vsecondarywiring
• 4NO+4NCauxiliarycontacts
• Operationcounterandcharge/dischargespringindicator
• Frontaccesstopositionindicator.
• Safeandreliableflexiblesecondarydisconnectsignals
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved.
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd FremontCA94539dir510.656.1600
www.iemfg.comIndustrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir866.302.9836
Vancouver OfficeCorporate OfficeIndustrial Electric Mfg™ 11902 Central Parkway JacksonvilleFL32224dir904.365.4444
Jacksonville Office
Breaker Ratings:
Vacuum Circuit Breaker
Astate-of-the-artANSI/IEEEvacuumcircuitbreakerwithfullinterchangeable capabilties allows for a 2000A unit that can be applied intoacubicleratedfor1200A,thusprovidingflexibilityforoperationandmaintenance requirements.
Circ
uit B
reak
er T
ype
Rat
ed M
axim
um V
olta
ge (k
V)
Nom
inal
Vol
tage
Cla
ss (k
V)
Freq
uenc
y (H
z)
Rat
ed V
olta
ge R
ange
Fac
tor (
K)
Pow
er F
requ
ency
1 m
in (k
vrm
s)
Ligh
ting
Impu
lse
1.2X
50 μ
S (k
V)
Rat
ed C
urre
nt (A
)
Rat
ed B
reak
ing
Cur
rent
(kA
)
Rat
ed M
akin
g C
urre
nt (k
Ap)
Rat
ed S
hort
Circ
uit T
ime
With
tnad
-3 s
ec (k
A)
Rat
ed C
rest
Vol
tage
(kVC
rest
)
Rat
ed T
ime
to C
rest
(T2
μS)
Rat
ed R
ise
of R
ecov
ery
Volt
Rat
ed P
erm
isib
le T
rippi
ng D
elay
(YSe
c)
Ope
ning
Tim
e (S
ec)
Bre
akin
g Ti
me
(Cyc
les)
Rat
ed O
pera
ting
Sequ
ence
Aux
iliar
y C
onta
cts
Insulation /Withstand
Class
Operation TimeCurrent
VIDER VVA
38 34.5 60 1.0 80 170 1200A 2000A
40 104 40 65.2 109 0.6 2 0.05 3 0-C-O 4 A/B
Rated Transient Recovery Voltage
(TRV)
IEM’s Unit Substations can utilize any configuration up to 27kV. They are designed and assembled to accommodate any commercially available transformer for either indoor or outdoor applications.
IEM Unit Substation•Primary – Air terminal chamber, vacuum circuit breaker or load interrupter switch to 27kV
•Transformer – Any commercially available transformer
•Secondary – Circuit breaker or fusible switches, UL 891, UL 1558, or CSA switchgear
•Maximum flexibility with wide range of components and ratings to meet application specifics
• Indoor or Outdoor assemblies/construction
•Configures to any transformer manufacturer available
•Comprehensive substation composite layout drawings.
•Superior flexibility options including increased utilization of space
• Improved voltage regulation and lowered power losses
•Complete coordination of substation components ensures precise fit
•Minimizes the use of secondary distribution cables and busway
IEM DifferenceFully rated bus is based on density ratings, not UL heat rise tests, resulting in more bus and lower operating temperatures.
All enclosures are designed for specific application with improved dimensional flexibility and finished using state of the art powder coating system providing an indoor finish that exceeds the 1500 hour salt spray testing requirement for outdoor equipment to 3000 hours.
Component and metering selections are based on value engineering for the application and optimized to meet specifications.
Technical SpecificationsIEM Switchgear meets seismic testing, circuit requirements as outlined by IEEE344 and ICC-ES-AC156.
IEM Unit Substation
Conforms to any commercially available transformer
Full Customization and Design Flexibility
Component & Metering Selection Options
Seismic Tested to Worst Case Response Spectrum
Indoor and Outdoor Applications
UL or CSA Listed; Meets ANSI, IEEE, and NEMA Standards
IEM ProductIEM Product
IEM Product: Unit Substation
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. 5.UnitSubstation_DS.v3
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.comCorporate Office Vancouver OfficeIndustrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Jacksonville OfficeIndustrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
IEM Custom Assemblies
IEM ProductIEM Product
IEM’s unique design and manufacturing capabilities provide for the integration of various components or products into a single assembly specifically suited to a defined purpose. The Custom Assembly process eliminates the need to compromise or combine several products from various manufacturers into a less than ideal solution.
Marina SubstationsIEM’s flexible approach to design and manufacturing is ideal for inland and coastal environment applications.•NEMA 3R Standard
•Temperature Fans for cooling
•Single and three phase models
•Double wall construction
•Ground fault monitoring system
•Up to 1200 Amp Main Circuit Breaker with 16 Single-Phase Branch Circuit Breakers or 10 Three-Phase Branch Circuit Breakers
•Marine grade aluminum enclosure
Emergency Fused Coordination Panels•Voltage: 120V – 600V; Ampacity: 250A and 400A
•65kA at 480V
•UL or CSA Listed
•Coordinated for emergency Loads
•Main breaker, main lugs, subfed breaker – optional
Walk-in EnclosuresCustom designed walk-in enclosures are designed to protect power distribution equipment in outdoor applications.•Allows any size layout or configuration
•Built and shipped in one unit, no assembly on-site required
• Installed and wired equipment to customer specific application
•Custom paint and sheet metal fabrication per application
Generator Cable Tap BoxesIEM’s customizable generator cable tap boxes are
pass-through devices that can safely connect a stand-by
power circuit breaker with a portable generator.•Rated for 600A applications at 240V or 480V
•Wall mounted/pad mounted
•Free standing
•Lug and cam lock connections available
•Power meters
IEM DifferenceFully rated bus is based on density ratings, not UL heat rise tests, resulting in more bus and lower operating temperatures.
All enclosures are designed for specific application with improved dimensional flexibility and finished using state of the art powder coating system providing an indoor finish that exceeds the 1500 hour salt spray testing requirement for outdoor equipment to 3000 hours.
Component and metering selections are based on value engineering for the application and optimized to meet specifications.
IEM Product: Custom Assemblies
©2013 IEM. Industrial Electric Mfg™ and the IEM logo design are trademarks of Industrial Electric Mfg. in the U.S. and other countries. All rights reserved. 7.CustomAssy_DS.v3
Industrial Electric Mfg.™ (IEM)
Headquartered in Fremont, CA, IEM is the largest independent full-line manufacturer of electrical distribution and power quality equipment in the U.S. For over half a century, IEM has delivered customer-specific solutions to meet the ever changing power requirements of growth industries in North America. At IEM, tradition and technology still drive innovation. An experienced engineering staff and one of the most flexible design and manufacturing systems in the industry set IEM apart from standard product manufacturers.
Tradition. Technology. Innovation.
Industrial Electric Mfg™ 48205 Warm Springs Blvd Fremont CA 94539dir 510.656.1600
www.iemfg.comCorporate Office
Industrial Electric Mfg™ Unit 201 - 27353 58th Crescent Langley BC V4W 3W7dir 866.302.9836
Vancouver Office
Industrial Electric Mfg™ 11902 Central Parkway Jacksonville FL 32224dir 904.365.4444
Jacksonville Office