Vessel Head Ends

(08) 9267 5500

[email protected]

HomeAbout

HSEOrganisational ChartClient Feedback

ServicesHeavy EngineeringOnshore / Offshore ServicesHeads, Ends, Knuckles & DishesRolling & PressingStructural Section RollingHeat TreatmentMaintenance & RefurbishmentEquipment HireSteel Art / Architectural

Heavy Engineering ProjectsOnshore / Offshore ProjectsContact Us

ServicesHeavy Engineering

Pressure VesselsHeavy Fabrication

Onshore / Offshore ServicesComposite Piping Systems (Fibreglass)High Density Polyethylene (HDPE) Piping SystemsMetallic Piping SystemsHydro TestingTrainingSafety Data SheetsPiping Stress Analysis

Heads, Ends, Knuckles & DishesTorispherical, Semi Ellipsoidal & Hemispherical Heads/EndsTank Ends & Flat EndsKnuckles - Pressed & RolledSelf-Supporting Domed RoofsConvex Weld BandsConvolution Bellows & Expansion JointsTori / Knuckle Cones for Pressure VesselsDishes & Spherical Covers

Rolling & PressingPlate RollingHydraulic Brake Press Machines - Plate Forming & StraighteningPress Equipment for Load Testing

Structural Section RollingHeat TreatmentMaintenance & RefurbishmentEquipment HireSteel Art / Architectural

Wenco | Torispherical, Semi Ellipsoidal & Hemispherical Heads/Ends http://www.wenco.com.au/services/heads-ends-knuckles-dishes/torispher...

1 de 4 01/09/2014 09:41 a.m.

Make an Enquiry

Full Name *

Email Address *

Phone Number

Comments *

Security Code

Click the letters above for another code

HomeServices

Heads, Ends, Knuckles & DishesTorispherical, Semi Ellipsoidal & Hemispherical Heads/Ends

Torispherical, Semi Ellipsoidal & Hemispherical Heads / EndsTorispherical Heads / Ends

Note: The ICR is equal to the I.D. of the head/end or less. The IKR is 10% of the I.D. The SF is normally between 30mm to 50mm. We can offervarious SF as required. The ITH is 20% of the I.D. excluding SF.

2:1 Semi Ellipsoidal Heads / Ends


2 de 4 01/09/2014 09:41 a.m.

Note: The ICR is 0.8 of the O.D of the head/end. The IKR is 0.154 of the O.D of the head. The SF is normally between 30mm - 75mm. The ITH is25% of the I.D. excluding SF.

Hemispherical Heads / EndsHemispherical heads / ends allow more pressure than any other formed head / end.

Note: Hemispherical heads / ends are formed with petals and a crown. The number of petals depends on the size of the head and the thickness of theplate to be used. The depth of the head is half of the diameter.

Kettles / Pans for Lead & Zinc Smelting


3 de 4 01/09/2014 09:41 a.m.

Contact us today on 08 9267 5500 to discuss your requirements,or alternatively email us on [email protected]

Phone:

(08) 9267 5500

Email:

[email protected]

Address:

1 Ladner Street, O'Connor,Western Australia, 6163

Sitemap

HomeAboutServicesHeavy Engineering ProjectsOnshore / Offshore ProjectsContact Us

Services

Heavy EngineeringOnshore / Offshore ServicesHeads, Ends, Knuckles & DishesRolling & PressingStructural Section RollingHeat TreatmentMaintenance & RefurbishmentEquipment HireSteel Art / Architectural

Wenco Engineering 2014 | Powered by Two Moons Consulting, Perth, WA | log in


4 de 4 01/09/2014 09:41 a.m.

Vessel Head Ends

Documents

Transcript of Vessel Head Ends