Vertical Exhaust Duct (VED) System D C D
2
Vertical Exhaust Duct (VED) System AR7751, AR7751W, AR7752, AR7752W, AR7753, AR7753W, AR7754, AR7754W, AR7755, AR7755W, AR7756, AR7756W Customer support for this or any other Schneider Electric product is available at www.schneider-electric.com. © 2016 Schneider Electric. All Rights Reserved Inventory Assembly ns1804a 02/2018 990-3958C A B C D E E E E A A A A A A B C D M6 (X11) M8 M3.5 (X36) M10 M4 M3.5 (X36) M6 (X11) AR7755 & AR7756 ONLY Vertical Exhaust Duct M6 (X6) M3.5 (X8) AR7755 & AR7756 ONLY A B A B M3.5 (X16) C C D D M3.5 (X16) ns1800a ns2829a C3H3O Thoroughly clean the surface receiving the gasket material with a 50/50 water/alcohol solution on a lint free cloth or a commercially purchased alcohol wipe intended for this use. Allow the surface to dry completely before applying the gasket material. ns2830a 1 2 3 4 5 6 Remove only a few inches of the backing tape protecting the adhesive side of the gasket when preparing for installation. NOTE: Removal of too much of the backing tape at one time risks contamination of the adhesive which can cause adhesion failure. NOTE: Discard any gasket material that is removed even if only to reposition it. Clean the area again with the alcohol wipe and use a new piece of gasket material. NOTE: A gasket installation video is available at https://www.trrimlok.com/rsinstall ns1793a X4 X4 M6 (X6) Installation X2 ns1820a X4 Door Seal ns1819a 30# ns2831a Use a roller to press the gasket into place. Press the roller down firmly using about 30 lb/in of applied pressure. NOTE: Wait 24 hours for adhesive to set before compressing or stressing the gasket.
Transcript of Vertical Exhaust Duct (VED) System D C D
Vertical Exhaust Duct (VED) System
AR7751, AR7751W, AR7752, AR7752W, AR7753, AR7753W, AR7754, AR7754W, AR7755, AR7755W, AR7756, AR7756W
Customer support for this or any other Schneider Electric product is available at www.schneider-electric.com.
© 2016 Schneider Electric. All Rights Reserved
Inventory
Assembly
ns1804a
02/2018990-3958C
A B
C D
EEEEAAAAAA
B C D
M6 (X11)M8
M3.5 (X36)
M10
M4
M3.5 (X36) M6 (X11)
AR7755 & AR7756 ONLY
Vertical Exhaust Duct
M6 (X6)
M3.5 (X8)AR7755 & AR7756 ONLY
A B
AB
M3.5 (X16)
C
C
D
D
M3.5 (X16)
ns1800a
ns2829a
C3H3O
Thoroughly clean the surface receiving the gasket material with a 50/50 water/alcohol solution on a lint free cloth or a commercially purchased alcohol wipe intended for this use. Allow the surface to dry completely before applying the gasket material.
ns2830a
1
23
4
5
6
Remove only a few inches of the backing tape protecting the adhesive side of the gasket when preparing for installation.NOTE: Removal of too much of the backing tape at one time risks contamination of the adhesive which can cause adhesion failure.
NOTE: Discard any gasket material that is removed even if only to reposition it. Clean the area again with the alcohol wipe and use a new piece of gasket material.
NOTE: A gasket installation video is available at https://www.trrimlok.com/rsinstall
ns1793a
X4
X4
M6 (X6)
Installation
X2
ns1820a
X4
Door Seal
ns1819a
30#
ns2831a
Use a roller to press the gasket into place. Press the roller down firmly using about 30 lb/in of applied pressure.
NOTE: Wait 24 hours for adhesive to set before compressing or stressing the gasket.
ns18
23a
SIDE VIEW
TOP VIEW
ns1841a
ns1842a
SIDE VIEW
TOP VIEW
ns1843a
NOTE: Be sure to use the gasket installation instructions from the Assembly section when installing gasket material in the Installation section.
ns1822a
48U
A
A
A
A
B
C
DE
A
Floor Seal
M8 (X2)
ns1835a
ns1836a
Roof
X2ns1806a
ns1809a
M4 (X2)ns1808a
ns1805a
M10 (X2)
M6 (X2)
ns1815a
X4
ns18
40a
M6 (X2)
ns1840a
ns1844a
Accessories (not included)
Duct
