Vertical Alignment
description
Transcript of Vertical Alignment
![Page 1: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/1.jpg)
1
Vertical AlignmentVertical Alignment
CE 453 Lecture 20Sources: A Policy on Geometric Design of Highways and Streets (The Green Book). Washington, DC. American Association of State Highway and Transportation Officials, 2001 4th Edition, and FHWA’s Flexibility in Highway Design
![Page 2: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/2.jpg)
2
Coordination of Vertical and Coordination of Vertical and Horizontal AlignmentHorizontal Alignment
Curvature and grade should be in proper balance– Avoid
Excessive curvature to achieve flat grades
Excessive grades to achieve flat curvature
Vertical curvature should be coordinated with horizontal
Sharp horizontal curvature should not be introduced at or near the top of a pronounced crest vertical curve– Drivers may not perceive change in
horizontal alignment esp. at night
Image source: http://www.webs1.uidaho.edu/niatt_labmanual/Chapters/geometricdesign/theoryandconcepts/DescendingGrades.htm
![Page 3: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/3.jpg)
3
Coordination of Vertical and Coordination of Vertical and Horizontal AlignmentHorizontal Alignment
Sharp horizontal curvature should not be introduced near bottom of steep grade near the low point of a pronounced sag vertical curve– Horizontal curves appear distorted– Vehicle speeds (esp. trucks) are highest
at the bottom of a sag vertical curve– Can result in erratic motion
![Page 4: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/4.jpg)
4
Coordination of Vertical and Coordination of Vertical and Horizontal AlignmentHorizontal Alignment
On two-lane roads when passing is allowed, need to consider provision of passing lanes– Difficult to accommodate with certain
arrangements of horizontal and vertical curvature
– need long tangent sections to assure sufficient passing sight distance
![Page 5: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/5.jpg)
5
Coordination of Vertical and Coordination of Vertical and Horizontal AlignmentHorizontal Alignment
At intersections where sight distance needs to be accommodated, both horizontal and vertical curves should be as flat as practical
In residential areas, alignment should minimize nuisance to neighborhood– Depressed highways are less visible– Depressed highways produce less noise– Horizontal alignments can increase the buffer
zone between roadway and cluster of homes
![Page 6: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/6.jpg)
6
Coordination of Vertical and Coordination of Vertical and Horizontal AlignmentHorizontal Alignment
When possible alignment should enhance scenic views of the natural and manmade environment– Highway should lead into not away
from outstanding views– Fall towards features of interest at low
elevation– Rise towards features best seen from
below or in silhouette against the sky
![Page 7: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/7.jpg)
7
Coordination of Horizontal Coordination of Horizontal and Vertical Alignmentand Vertical Alignment
Coordination of horizontal and vertical alignment should begin with preliminary design
Easier to make adjustments at this stage
Designer should study long, continuous stretches of highway in both plan and profile and visualize the whole in three dimensions
![Page 8: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/8.jpg)
8
Coordination of Horizontal Coordination of Horizontal and Vertical Alignmentand Vertical Alignment
![Page 9: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/9.jpg)
9
Should be consistent with the topography
Preserve developed properties along the road
Incorporate community valuesFollow natural contours of the land
Coordination of Horizontal Coordination of Horizontal and Vertical Alignmentand Vertical Alignment
![Page 10: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/10.jpg)
10
Good Coordination of Good Coordination of Horizontal and Vertical Horizontal and Vertical
AlignmentAlignment Does not affect aesthetic, scenic, historic, and cultural resources along the way
Enhances attractive scenic views– Rivers– Rock formations– Parks– Historic sites– Outstanding buildings
![Page 11: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/11.jpg)
11
![Page 12: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/12.jpg)
12
![Page 13: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/13.jpg)
13
![Page 14: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/14.jpg)
14
![Page 15: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/15.jpg)
15
![Page 16: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/16.jpg)
16
Vertical CurvesVertical CurvesConnect roadway grades
(tangents)Grade (rise over run)
– 10% grade increases 10’ vertically for every 100’ horizontal
![Page 17: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/17.jpg)
17
Vertical CurvesVertical Curves Ascending grade:
– Frequency of collisions increases significantly when vehicles traveling more than 10 mph below the average traffic speed are present in the traffic stream
![Page 18: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/18.jpg)
18
ExampleExample If a highway with
traffic normally running at 65 mph has an inclined section with a 3% grade, what is the maximum length of grade that can be used before the speed of the larger vehicles is reduced to 55 mph?
![Page 19: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/19.jpg)
19
ExampleExample
a 3% grade causes a reduction in speed of 10 mph after 1400 feet
![Page 20: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/20.jpg)
20
Climbing lanesClimbing lanes When flatter grades cannot be accommodated,
consider climbing lane when all 3 of the following criteria are met (AASHTO):– Upgrade traffic flow rate in excess of 200 vehicles per
hour.– Upgrade truck flow rate in excess of 20 vehicles per
hour.– One of the following conditions exists:
A 15 km/h or greater speed reduction is expected for a typical heavy truck.
Level-of-service E or F exists on the grade. A reduction of two or more levels of service is experienced
when moving from the approach segment to the grade.
![Page 21: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/21.jpg)
21
Descending GradesDescending Grades Problem is increased speeds and loss of control
for heavy trucks Runaway vehicle ramps are often designed and
included at critical locations along the grade Ramps placed before each turn that cannot be
negotiated at runaway speeds Ramps should also be placed along straight
stretches of roadway, wherever unreasonable speeds might be obtained
Ramps located on the right side of the road when possible
![Page 22: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/22.jpg)
22
Maximum GradesMaximum GradesPassenger vehicles can easily
negotiate 4 to 5% grade without appreciable loss in speed
Upgrades: trucks average 7% decrease in speed
Downgrades: trucks average speed increase 5%
![Page 23: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/23.jpg)
23
Vertical CurvesVertical Curves Parabolic shape VPI, VPC, VPT, +/- grade, L Types of crest and sag curves
![Page 24: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/24.jpg)
24
Vertical CurvesVertical Curves Crest – stopping, or passing sight
distance controls Sag – headlight/SSD distance, comfort,
drainage and appearance control Green Book vertical curves defined by
K = L/A = length of vertical curve/difference in grades (in percent) = length to change one percent in grade
![Page 25: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/25.jpg)
25
Parabola y = ax2 + bx + cWhere:
y = roadway elevation at distance x x = distance from beginning of vertical
curve a = G2 – G1 L b = G1 c = elevation of PVC
Vertical Curve EquationsVertical Curve Equations
![Page 26: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/26.jpg)
26
Vertical Curve AASHTO Controls Vertical Curve AASHTO Controls (Crest)(Crest)
Minimum length must provide stopping sight distance S
Two situations (both assume h1=3.5’ and h2=2.0’)
Source: Transportation Engineering On-line Lab Manual, http://www.its.uidaho.edu/niatt_labmanual/
![Page 27: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/27.jpg)
27
Assistant with Target Rod (2ft object height)
Observer with Sighting Rod (3.5 ft)
![Page 28: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/28.jpg)
28
Vertical Curve AASHTO Controls Vertical Curve AASHTO Controls (Crest)(Crest)
Note: for passing sight distance, use 2800 instead of 2158
![Page 29: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/29.jpg)
29
Example: Try SSD > L, Design speed is 60 mph G1 = 3% and G2 = -1%, what is L? (Assume grade = 0% for SSD)SSD = 570feet ( see: Table 3.4 of text)
Lmin = 2 (570’) – 2158’ = 600.5’
|(-1-3)|S < L, so it doesn’t match condition
![Page 30: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/30.jpg)
30
Example: Assume SSD < L, Design speed is 60 mph G1 = 3% and G2 = -1%, what is L? Assuming average grade = 0%SSD = 570 feet - ( Table 3.4 of text)Lmin = |(-3 - 1)| (570 ft)2 = 602 ft
2158 SSD < L, equation matches condition
![Page 31: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/31.jpg)
31
Evaluation of example: The AASHTO SSD distance equations
provided the same design length from either equation in this special case. (600 compared to 602 - this is not typical)
Garber and Hoel recommend using the most critical grade of - 1% for SSD computation.– Resulting SSD would be: d = 573 ft– Resulting minimum curve: L = 608 ft
Difference between 602 and 608 is too small to worry about
![Page 32: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/32.jpg)
32
Text example : g1 = + 3% g2 = -3%Design speed of 60 mph If SSD = 570’ (AASHTO – no grade consideration) Resulting minimum curve: L = 903 ft (S < L) Consider grade per Garber and Hoel (p 693-694) SSD, using - 3% grade, 598’ Resulting minimum curve L = 994 ft
![Page 33: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/33.jpg)
33
Assessment of grade Assessment of grade adjustmentadjustment
If sight distance is less than curve length, the driver will be on an upgrade a greater portion of the distance than on a down grade (for eye ht = 3.5’ and object ht = 2.0 ft, 68% of the distance between eye and object will be on + grade.)For crest vertical curve, selecting a curve length based on down grade SSD may produce an overly conservative design length.
![Page 34: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/34.jpg)
34
AASHTO design tablesAASHTO design tables Vertical curve length can also be found in
design tables
L = K *AWhere
K = length of curve per percent algebraic difference in intersecting grade
Charts from Green Book
![Page 35: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/35.jpg)
35From Green book
![Page 36: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/36.jpg)
36From Green book
![Page 37: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/37.jpg)
37
Vertical Curve AASHTO Controls Vertical Curve AASHTO Controls (Crest)(Crest)
Since you do not at first know L, try one of these equations and compare to requirement, or use L = KA (see tables and graphs in Green Book for a given A and design speed)
![Page 38: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/38.jpg)
38
Chart vs computedChart vs computedFrom chart V = 60 mph K = 151 ft / % change
For g1 = 3 g2 = - 1 A = |g2 – g1| = |-1 – 3| = 4
L = ( K * A) = 151 * 4 = 604
![Page 39: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/39.jpg)
39
Sag Vertical CurvesSag Vertical CurvesSight distance is governed by
night- time conditions– Distance on curve illuminated by
headlights need to be consideredDriver comfortDrainageGeneral appearance
![Page 40: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/40.jpg)
40
Vertical Curve AASHTO Controls Vertical Curve AASHTO Controls (Sag)(Sag)
Headlight Illumination sight distance
S < L: L = AS2
400 + (3.5 * S)
S > L: L = 2S – (400 + 3.5S) A
![Page 41: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/41.jpg)
41
Vertical Curve AASHTO Controls Vertical Curve AASHTO Controls (Sag)(Sag)
For driver comfort use: L > AV2
46.5 (limits g force to 1 fps/s)
To consider general appearance use:
L > 100 A
![Page 42: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/42.jpg)
42
Sag Vertical Curve: ExampleA sag vertical curve is to be designed to join a –3% to a +3% grade. Design speed is 40 mph. What is L?Skipping steps: SSD = 313.67 feet S > LDetermine whether S<L or S>L
L = 2(313.67 ft) – (400 + 2.5 x 313.67) = 377.70 ft [3 – (-3)]313.67 < 377.70, so condition does not apply
![Page 43: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/43.jpg)
43
Sag Vertical Curve: ExampleA sag vertical curve is to be designed to join a –3% to a +3% grade. Design speed is 40 mph. What is L?Skipping steps: SSD = 313.67 feet
L = 6 x (313.67)2 = 394.12 ft 400 + 3.5 x 313.67 313.67 < 394.12, so condition applies
![Page 44: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/44.jpg)
44
Sag Vertical Curve: ExampleA sag vertical curve is to be designed to join a –3% to a +3% grade. Design speed is 40 mph. What is L?Skipping steps: SSD = 313.67 feetTesting for comfort:L = AV2 = (6 x [40 mph]2) = 206.5 feet 46.5 46.5Testing for appearance:L = 100A = (100 x 6) = 600 feet
![Page 45: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/45.jpg)
45
Vertical Curve AASHTO Controls Vertical Curve AASHTO Controls (Sag)(Sag)
For curb drainage, want min. of 0.3 percent grade within 50’ of low point = need Kmax = 167 (US units)
For appearance on high-type roads, use min design speed of 50 mph (K = 100)
As in crest, use min L = 3V
![Page 46: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/46.jpg)
46
Other important issues:Other important issues:Use lighting if need to use shorter
L than headlight requirements Sight distance at under crossings
![Page 47: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/47.jpg)
47
![Page 48: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/48.jpg)
48
Example: A crest vertical curve joins a +3% and –4% grade. Design speed is 75 mph. Length = 2184.0 ft. Station at VPI is 345+ 60.00, elevation at VPI = 250 feet. Find elevations and station for VPC (BVC) and VPT (EVC).L/2 = 1092.0 ftStation at VPC = [345 + 60.00] - [10 + 92.00] = 334 + 68.00Vertical Diff VPI to VPC: -0.03 x (2184/2) = - 32.76 feetElevationVPC = 250 – 32.76 = 217.24 feet
Station at VPT = [345 + 60.00] + [10 + 92.00] = 357 + 52.00Vertical Diff VPI to VPT = -0.04 x (2184/2) = - 43.68 feetElevation VPT = 250 – 43.68 = 206.32 feet
![Page 49: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/49.jpg)
49
Example: A crest vertical curve joins a +3% and –4% grade. Design speed is 75 mph. Length = 2184.0 ft. Station at VPI is 345+ 60.00, elevation at VPI = 250 feet. Station at VPC (BVC) is 334 + 60.00, Elevation at VPC: 217.24 feet. Calculate points along the vertical curve.X = distance from VPCY = Ax2
200 LElevationtangent = elevation at VPC + distance x gradeElevationcurve = Elevationtangent - Y
![Page 50: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/50.jpg)
50
Example: A crest vertical curve joins a +3% and –4% grade. Design speed is 75 mph. Length = 2184.0 ft. Station at VPI is 345+ 60.00, elevation at VPI = 250 feet. Find elevation on the curve at a point 400 feet from VPC.
Y = A x 2 = - 7 x (400 ft)2 = - 2.56 feet 200L 200 (2814)Elevation at tangent = 206.32 + (400 x 0.03) = 218.32Elevation on curve = 218.32 – 2.56 feet = 226.68’
![Page 51: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/51.jpg)
51Calculating x from VPC, calculating tangent elevation along +3% tangent
Y
![Page 52: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/52.jpg)
52
![Page 53: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/53.jpg)
53Calculating x from VPT, calculating tangent elevation along +4% tangent
Y
![Page 54: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/54.jpg)
54Source: Iowa DOT Design Manual
![Page 55: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/55.jpg)
55Source: Iowa DOT Design Manual
![Page 56: Vertical Alignment](https://reader033.fdocuments.in/reader033/viewer/2022042616/56813ab2550346895da2b22b/html5/thumbnails/56.jpg)
56Source: Iowa DOT Design Manual
Note: L is measured from here to here
Not here