Versalis and the tyre market: a complete portfolio of technologies and products … · 2013. 11....
Transcript of Versalis and the tyre market: a complete portfolio of technologies and products … · 2013. 11....
1
Versalis and the tyre market: a complete portfolio of technologies and products (ESBR, SSBR, HCBR) Gabriele Gatti- versalis Elastomer Process and Technology Manager
Bangkok, November 15th, 2013
2 2
Focus on tyres
Elastomers are basic in most of tyre components. New Green Policies in Europe, NA, Japan, require extensive use of sSBR and BR Nd high cis in tread, and BR Nd high cis in sidewall to reduce CO2 emissions
Typical polymer content
Passenger Car tyre
NR: 1 kg
eSBR: 1,5 kg
sSBR: 1,2 kg
BR: 0,8 kg
Butyl rubber:0,5 kg
Heavy Truck tyre
NR: 15 kg
eSBR: 1.6 kg
sSBR: 1 kg
BR: 5.6 kg
Butyl rubber: 1 kg
3 3
versalis with its proprietary technologies covers most of the synthetic elastomers requirement for the tyres’ manufacturing:
versalis has proven experience of large elastomers complexes in which all these technologies can be applied and mutually optimized
Available technologies for the tyre market:
Typical worldscale plant Size (at product mix)
1 Continuous (cold) emulsion SBR (eSBR) 65 – 130 kta
2 Batch solution SBR (sSBR/LCBR swing plant)
40 – 60 kta
3 Continuous solution SBR (sSBR/LCBR swing Plant)
40 – 60 kta
4 High Cis polybutadiene (NdBR) 45 – 80 kta
4 4
Typical workflow
Kinetics
Structure & Formulation Chemistry
Scale-up Pilot plants
Process engineering Process development
Basic engineering Calculation design
Polymer processing End-uses properties
Industrialization
Chemical & physical characterization
Polymer physiscs
5 5
versalis approach to the elastomers technologies for the tyre market
Technology Every product family requires a specific technology which has been
developed by versalis for years in its own Plants.
R&D Dept
New products are studied at our R&D Dept which is located at Ravenna, Italy, where pilot plants of many sizes allow us to produce from few grams of of rubber using bench-scale reactors up to 20 kg/h 24/7 to sample tons of elastomers to the tyre manufacturers
Process
Every step of production of each process has been deeply studied, applied and proven. This continuous development of technology is mirrored in the production Plants for the internal production, for JV or Licensing.
Application
The application of these technogies can be flexible in order to complain with the specific requirement of the Site or the Partner:
Stand-alone plants, single or multiple production lines, swing;
Integrated plants, with optimized lines configuration;
Multiple plants for different technologies, optimized and integrated in a larger Site.
Policy
Versalis policy is to provide the internal or external Client with a tailored design in order to shorten the normally long time required to make the integration and optimization of the lines before the EPC stage of the Project.
6 6
versalis rubber complex – 3D general model – Project «α»
1 eSBR line
1 sSBR/LCBR swing line
1 HCBR line
1 SBC swing line
7 7
versalis rubber complex – Plot Plan – Project «β»
8 8
versalis sSBR Plant – Project «γ» – 3D general model
9 9
versalis elastomers assets – tyre market
versalis assets – solution SBR (batch and continuous)
Continuous sSBR/LCBR swing versalis Grangemouth, U.K. Operation
Batch sSBR/LCBR swing versalis Grangemouth, U.K. Operation (under debottlenecking)
Batch sSBR versalis Ravenna, Italy Construction
Batch sSBR/LCBR/TPR swing Licensed to Petrochina Dushanzi, PRC
Operation
Continuous sSBR/LCBR/TPR swing
Licensed to Petrochina Dushanzi, PRC
Operation
Batch sSBR/LCBR/TPR swing Licensed, Mid East Construction
Continuous sSBR/LCBR swing Licensed, South East Asia Construction
Continuous sSBR/LCBR swing JV, Far East Engineering
Batch sSBR/LCBR swing JV, Far East Engineering
Continuous sSBR/LCBR swing Licensed, Mediterrean area Engineering
10 10
Versalis assets – emulsion SBR and HCBR
versalis assets – emulsion SBR
eSRB versalis Hythe, U.K. Operation
eSBR versalis Ravenna, Italy Operation
eSBR Licensed, Mid East Construction
eSBR Licensed, South East Asia Construction
eSBR Licensed, India Start-up
versalis assets – HCBR (Nd BR)
HCBR versalis Ravenna, Italy Operation
HCBR Licensed, Far East Construction
HCBR JV, Far East Engineering
HCBR Licensed, South East Asia Construction
11 11
Solution SBR (sSBR)
Polymerization basics
Solution polymerized styrene-butadiene rubber is obtained by anionic copolymerization of styrene and butadiene initiated by lithium alkyls in aliphatic or cycloaliphatic solvent; due to the large difference of reactivity ratios for the two monomers, addition of a living chain-end modifier changing the above-mentioned reactivities is required to obtain a well randomized copolymer.
A proper choice of modifier allows to carry out the polymerization reaction without any termination of active chain-ends; which in turn leads to high yields through the coupling or branching reactions taking place at monomers depletion.
The rubber macrostructure can be efficiently managed/driven by a proper selection of polymerization type (batch, continuous), reaction conditions and suitable coupling or branching agents, greatly enhancing the final properties of vulcanized rubber.
12 12
The competitiveness of our proprietary sSBR/LCBR swing technology is based on the following main key-points
1 Relevant savings in term of steam consumption due to aliphatic or cycloaliphatic nature of solvent, which in turn also leads to improvements in environmental impact.
2 Relevant reduction in investment cost due to carrying out the reaction adiabatically or in temperature rise control, which also allows easier reaction control as well as saving in energy consumption.
3 Large production flexibility due to availability of both batch and continuous polymerization technologies, whose selection is driven by the final application of the product.
4 High and medium vinyl grades as well as Dry and Oil Extended polymers are allowed.
5 Special purification section brings raw material impurities to negligible level, avoiding detrimental effects on both the process and structural parameters of the product.
6 Capacity up to 60 kt/y per reaction unit is afforded, with a single finishing line capacity up to 30 kt/y for batch grades and 40 kt/y for continuous grades.
7 Perfect randomization of styrene in polymer chain is allowed by the proper use of substances which modify the leaving chain ends.
8 Production of different grades of sSBR ranging from low styrene-low vinyl to high styrene-high vinyl grades is allowed, based on both batch or continuous processes.
9 Production of polymers with different macrostructure: linear radial or branched.
Highlights
13 13
versalis sSBR swing technology – sSBR Plant block diagram
Polymerization Flash and blending
Stripping
Finishing
Solvent purification
Monomer(s) purification
Chemicals preparation
Chemicals & additives
Monomers
Finished product (25-35 kg bales)
Fresh solvent
Wet solvent
14 14
versalis sSBR/LCBR swing technology – Batch Plant
Batch reactors, boiling type:
The reactor is first supplied with solvent, than monomer(s) are added and the initiator starts the polymerization. Polymerization heat is used to reach the required temperature, that is controlled by means of a vapour condenser. This Reactor is able to produce also LCBR grades. For both families (sSBR/LCBR) dry or oil-extended grades can be produced.
Solvent, monomers, chemicals
Polymer solution (cement)
15 15
versalis sSBR/LCBR swing technology – Continuous Plant
Solvent, monomers, chemicals
SSBR Polymer solution (cement)
Note (*) – Reactors’ alignment changes in case of LCBR production, but no other equipment is required
Continuous reactors:
SSBR: The reactor train requires a first boiling reactor (peak reactor) followed by 3/4 adiabatic reactors to complete the polymerization
LCBR: 1 adiabatic reactor and 1 flash tank (*)
chemicals
16 16
versalis sSBR swing technology – main info
Batch process Continuous process
Reactor type: Batch stirred reactor, boiling type
Continuous stirred tank reactor, first one (peak reactor) boiling type
Reactors Number: 2-4 reactors / polymerization line
1 peak + 3-4 afterpeak reactors/ pol. line
Polymerization Pressure: < 10 bar(g) < 10 bar(g)
Polymerization Temperature:
< 120 °C < 120 °C
Solids concentration: < 25% < 25%
Monomers conversion: complete complete
Solvent: Cyclohexane, cyclopentane, n-Hexane
LCBR production capability
Yes Yes
17 17
versalis sSBR swing technology
Raw materials: solvent choice
According to specific products’ needs and Site climate conditions, several solvents can be used. The following table shows the possible options:
Cyclohexane: Lower volatility, less solvent consumption, better for warm/hot climates;
n-Hexane: Preferred for warm/cold climates for random copolymers, lower energy consumption;
Cyclopentane: Best choice for warm/cold climates, the lowest energy consumption.
18 18
versalis sSBR swing technology
Formulation
Raw Materials: Chemicals/Additives:
Butadiene Monomer Initiator
Styrene Monomer Coupling agents, shortstop
Extender oil (DAE, RAE, TDAE, MES) Activator
Solvent Antioxidants
Stripping additives
Finishing additives
Monomer column additive
All the chemicals and additives are easily available on the worldwide market
19 19
Emulsion SBR (eSBR)
Polymerization basics
Emulsion polymerized styrene-butadiene rubber for the tyre market is obtained by free radical emulsion (cold) polymerization. The emulsion system is composed by an aqueous phase in which monomer droplets , initiator, chain transfer agent and surfactant molecules are present.
Polymerization takes place when a radical migrates into a micelle and reacts with monomer. The chain continues to propagate with the available monomer until another radical enters the same micelle. The final product is a dispersion of polymer particles in water (latex) stabilized by an adsorbed layer of soap
A shortstopping chemical is added to stop the reaction before crosslinking occurs.
20 20
The competitiveness of our proprietary eSBR technology is based on the following main key-points
1 High polymerization conversion reduces monomers and utilities consumptions leading to both high productivity and process capability. Lower dimensions of recovery section leads to lower capital investment.
2 Rejected monomer quantity is reduced thanks to a specific section design, integrated with upstream plants, allowing reduction of slop quantity. versalis is able to design this recovery section based on both client needs as well as site conditions.
3 The wide range of products grades coupled with a real process know-how enables meeting the specific needs of the customer. High capacity and flexibility allow production, in the same continuous reactors train, of base Latexes blendable with batch or semibatch latexes to produce a HSR/HSL grades and SBR latexes.
4 All the enviromental issues coming from gaseous effluents, liquid effluents, water consumption and solids effluents have been deeply considered in the design base of each process stage, according to the best available technologies as well as to the IISRP suggestions to the E.U. Authorities.
5 Water recycle: the watery phase recovered after the latex stripping are recycled to reaction, no water streams from reaction or monomer recovery to CWWT.
6 VOC captation: vapour streams from reaction and recovery areas are connected to abatement/flare system also for maintenance operations (low emission factors).
7 High valuable technical assistance is given to the customer by versalis R&D structure
Highlights
21 21
versalis eSBR technology – eSBR Plant block diagram
Finishing
Extender oil storage
Refrigerating unit
Chemicals & additives
Finished product (25-35 kg bales)
Fresh monomers, demi water
Unreacted monomers
Solvent for chemical cleaning and waste
water stripping
Extender oil
Polymerization
Monomers and demi water
storage
Chemicals preparation
Monomers recovery
22 22
versalis eSBR technology
Stirred reactors:
Reactors are full of polymerizing latex. Reaction is isothermal; chilling is provided by boiling ammonia (ammonia is the cheapest coolant). Reactors are chemically cleaned (no need of mechanical cleaning procedures)
Latex in
Liquid NH3
Gaseous NH3
Latex to other reactors
Mid size reactor (15-22 m3 each) to better fit the Smith-Ewart curve, to control the polymerization temperature
23 23
versalis eSBR technology – main info
eSBR process
Reactor type: train of continuous stirred tank reactors in series
Reactors Number: Typically 12-14, 15 to 22 m3 each
Polymerization Pressure: < 10 bar(g)
Polymerization Temperature: 5 - 10 °C
Solids concentration: < 25%
Solids at end of reaction: 20 – 30%
Monomers conversion: 62 – 75%
Emulsifying agent: fatty and/or rosin acid soap
24 24
versalis eSBR technology
Formulation
Raw Materials: Chemicals/Additives:
Butadiene Monomer Redox system (oxydant, reductant) and chelating agent
Styrene Monomer Shortstop
Extender oil (DAE, RAE, TDAE, MES, Naphtenic)
Rosin & fatty acids
Ammonia (refrigeration) Soda, Potash, Solfuric acid
Solvent for chemical cleaning
Single antioxydant, no-staining and no-nitrosamine precursor
Stripping additives
25 25
High-Cis Polybutadiene (NdBR)
Polymerization basics
High Cis Polybutadiene (HCBR) is a solution polymer (solvent: tipically n-hexane) obtained by using a Ziegler–Natta catalyst prepared by the reaction between an organic salt of Neodymium, an Aluminum Alkyl and an organic chlorinated compound. This catalyst is able to coordinate the reaction of butadiene monomer in Cis form producing a high cis polymer (> 97%).
Catalyst is preparation is based on two subsequent reactions:
Neodymium salt (Pre-catalyst) is prepared mixing Nd with organic and inorganic acids;
Catalyst is obtained by a second reaction which involves Pre-catalyst, an organometallic alkyl compound (aluminium based) and an organic chloride.
The preparation reactions are exothermic.
CIS 1,4 H H CIS UNIT H H \ / \ / C == C C == C / \ / \
-- CH2 CH2 -- CH2 CH2 -- CH2 CH2 --
\ / C == C / \ H H
TRANS 1,4 TRANS UNIT
H CH2 -- CH2 H H CH2 --
\ / \ \ \ / C == C C == C C == C / \ \ \ / \
-- CH2 H H CH2 -- CH2 H
VINYL 1,2
CH2 CH2 CH2
\\ \\ \\ CH H CH H CH H \ / \ / \ / C C C
\ / \ / \ / \ C C C
H2 H2 H2
26 26
The competitiveness of our proprietary HCBR technology is based on the following main key-points
1
Very high Cis content, low vinyl and high chain linerity which enhances the products’ mechanical properties:
high 1,4 cis content: Better tack and green strength
low vinyl content: Better crack growth and fatigue resistance
high chain linearity: Better wear resistance
Lower Hysteresis (lower RR)
Higher elasticity
2 Relevant savings in term of steam consumption due to aliphatic nature of solvent (typically industrial n-hexane), which in turn also leads to improvements in environmental health
3 Very good control of impurities level through a special design in purification section that leads to market required product quality
4 Special design of continuous and adiabatic section in order to minimize reactors fouling, to lower investment costs and to save energy
5 Recovery and recycle of non-reacted monomers which enhance the raw material consumption figures.
6 Normal antioxidants easily protect HCBR from oxidation during processing and storage because Nd does not catalyze the action of oxygen on HCBR, which is possible with the other metals (Ni, Co)
Highlights
27 27
versalis HCBR technology – HCBR Plant block diagram
Polymerization Flash and Blending
Stripping
Solvent purification
Chemicals & additives
Finished product (25-35 kg bales)
Fresh solvent
Chemicals preparation
Finishing
Recycle solvent + unreact. monomers purification
Wet solvent
Precatalyst and Catalist
preparation
Monomer purification
1,3 butadiene
28 28
versalis HCBR technology
Train of two continuous stirred reactors
Polymerization reaction is performed through two completely filled continuous reactors in series.
Solvent, monomer and catalyst are fed to first reactor where the monomer is partially converted. Then the cement is moved into the second reactor where the reaction is completed (98-99%). Solvent,
monomer and catalyst
Polymer solution
29 29
versalis HCBR technology – main info
HCBR process
Reactor type: train of 2 continuous stirred tank reactors in series + 1 spare, adiabatic
Temperature control: Monomer dilution Solvent feed temperature
Reactors Size: 50 m3 each
Polymerisation Pressure: < 10 bar(g)
Polymerisation Temperature: < 120 °C
Solids concentration: 12,5 – 14,5%
Monomers conversion: Min. 98%
30 30
versalis HCBR technology
Formulation
Raw Materials: Chemicals/Additives:
Butadiene Monomer Components of the catalytic system
Solvent Antioxidants
Stripping additives
Finishing additives
Monomer column additive
All the chemicals and additives are easily available on the worldwide market
31
Thank you!