VCR and Micro-Fit Fittings - Kylos...
Transcript of VCR and Micro-Fit Fittings - Kylos...
VCR Nuts, Caps, and Plugs
Product Binder
VCR® and Micro-Fit® Fittings
Swagelok, VCR, Split-Nut, Micro-Fit- TM Swagelok Company, © 2002 Swagelok Company, Printed in U.S.A., June 2002 MI MS-10-06 R0
The product binder contains full technical data on allSwagelok VCR and Micro-Fit fittings as well as othercomplete lines of valves and fittings.
For further information, visit us at:www.swagelok.com.
Male NPT
Male NPT bulkhead
Male weld
Straight thread o-ring seal male
Tube adapter
Swagelok tube fitting bulkhead
Swagelok tube fitting
Female NPT
Bulkhead
Double male
Double male reducing
Short tube butt weld Long tube butt weld
Short automatic tube butt weld
Blind (undrilled) gland
Reducing socket weld
Socket weld
Short socket weld
Long automatic tube butt weld
1/8 to 1 in. and 6 to 18 mm sizesHigh-purity stainless steels
Available surface finishes on glands andbodies are a roughness average of 10 µin.(0.25 µm) and 5 µin. (0.13 µm) Ra.
Material heat code is stamped onglands and all shapes to ensure raw material traceability.
Markings identify manufacturer, material, and whenapplicable, the appropriate process designatoraccording to Swagelok® Ultrahigh-Purity ProcessSpecification (SC-01).
Test port at two locationsfor easy leak testing
Female threads are silver-plated to ensureeasy and consistent assembly
Precision manufactured gasketfor maximum performance
No “virtual leak” zones
Side-load retainer gasket for easy installation,minimal clearance for removal
Double female reducing
Reducing
Reducing
FemaleUnion
Union Union
Tube butt weld bulkhead
VCR to male NPT
Female nut Female Split-NutTM assembly
Cap
Short male nut(for use with short gland)
Male nut
Male Split-Nut assembly
Plug with lanyardCap with lanyard
Plug
Female UnionMale NPT
Female NPT
Swagelok tube fitting
Rotating female
Female Union
Side-load retainer styleGasket retainer assembly Non-retained style Union
Bulkhead connector
Automatic tube weld
Tube butt weld
Tube butt weld
BODIES
GLAND
MaleFemale
NUTS
UnionELBOW
VCR Metal Gasket Face Seal Fitting
CONNECTORS UNIONS ELBOWS
UNION
Tube Facing Tool and Welding SystemMicro-Fit Weld FittingsTEES
ELBOWS
CROSS TRIBOW
Union
Extended Leg
Reducing
45° UnionTribowUnion
Extended Leg Union
Extended Leg
TEE
Reducing The tube facing toolcleanly and consistentlysquares tube ends inpreparation for orbitalwelding. The weldingsystem is designed tostreamline weldingoperations and managethe total weldingprocess.
TEE CROSS
CONNECTORS ELBOW
TEE
UNION
COUPLING
ADAPTER
BUSHING
VCR Bodies
VCR Welded Assemblies VCR Gaskets VCR High-Flow Connections “H” Type
VCR Glands
Ultrahigh-PurityA variety of Micro-Fit weld fittings areavailable with controlled surface finishes,electropolished and specially cleaned tomeet Ultrahigh-Purity system require-ments. For more information, refer toSwagelok Ultrahigh-Purity ProcessSpecification (SC-01).
Rounded body block preventsinjury or damage to other components during systemfabrication or maintenance.
Laser etch markingidentifies manufacturer, material, and when applicable, the appropri-ate process designatoraccording to SwagelokUltrahigh-Purity ProcessSpecification (SC-01).
Radius junctionallows for a smooth flowtransition and is designedto eliminate pockets andentrapment zones.
Material heat code is rollstamped during firstmanufacturing operationto ensure raw materialtraceability.
Square, sharp, burr-free tube weld ends enhance alignment,maintain tube wall uniformity,and promote weld repeatability.
FeaturesCompact design
accommodates tubing systemsrequiring miniaturization.allows close component spacing.provides flow and service ratings
equal to larger weld fittingsdesigned for the same size tubing.
Dimensional consistency
Material316L VIM VAR or 316L VAR
stainless steel
MICRO-FIT316 LV
P
L-15
MICRO-FIT316 LV
P
L-15
MICRO-FIT
316 LVP
L-15
MICRO-FIT316 LV
P
L-15
MICRO-FIT316 LV
P
L-15
MICRO-FIT
316 LVP
L-15
MICRO-FIT316 LV
P
L-15
MICRO-FIT316 LV
P
L-15
MICRO-FIT316 LV
P
L-15
Reducing
MICRO-FIT316 LV
P
L-15
Available surface finishesare a roughness averageof 10 µin. (0.25 µm) and5 µin. (0.13 µm) Ra