Vanguard Instruments Company, Inc....Transformer Diagnostic Testing Performing Winding Resistance...
Transcript of Vanguard Instruments Company, Inc....Transformer Diagnostic Testing Performing Winding Resistance...
Transformer Diagnostic Testing
Performing Winding Resistance and Turns Ratio Tests
Vanguard Instruments Company, Inc.
1520 S. Hellman Ave. Ontario, California 91761, USA
TEL: (909) 923-9390 FAX: (909) 923-9391
June 2016 Revision 1
REV 1 TRANSFORMER DIAGNOSTIC TESTING
1
Power transformers play a vital role in power transmission. They are used to raise or lower the voltages in the power delivery system. High voltage (HV) power transformers are very expensive to manufacture and require long lead times since they are very labor intensive. A failed transformer is not only costly to replace but also causes loss of revenue to the utilities. Due to this reason, proper maintenance to ensure reliable performance and longevity is of utmost importance.
In operation, all transformers are subjected to internal as well as external fault current. Transformers will see more external than internal fault. Fault current imposes high mechanical stresses on the transformer's windings and its mechanical structure. These high stresses weaken and alter the mechanical structure of the transformer. Hoop buckling of windings and winding deformations are typical effects of high stresses caused by a short circuit in the system. Also the heat generated during normal operation and during a fault, oxidizes the transformer oil. Over time, the interaction of the insulation paper (used for conductor wrapping) with the hot transformer oil weakens the dielectric strength of the transformer.
In current operational environments, getting the required long outage to test transformers is not that common. So when the outage is planned, all the required tests need to be performed quickly. Although all tests need to be performed during the short outage time, personnel safety should never be overlooked or compromised. For transformer maintenance, personnel safety and speedy testing are the two most important factors. Several different tests can be performed on a transformer to analyze its condition. The transformer winding integrity can be verified by using the Sweep Frequency Response Analyzer test. The transformer bushing and overall insulation integrity can be analyzed using the Tan-delta (or Power Factor) test. Chemical analysis of the transformer oil should be conducted to detect moisture and determine the dielectric strength of the oil. Additionally, transformer turns ratio and winding resistance tests are used to detect shorted windings and possible connection issues. The focus of this application note is on winding resistance and turns ratio tests.
Winding resistance tests can verify the winding connections to the transformer bushings, or the winding contact resistance (as in the case of the load tap changer and voltage regulator). A properly-designed winding resistance meter can obtain fast and accurate resistance readings when performing an HV transformer winding resistance test.
A typical transformer winding resistance meter employs a high DC power supply (20Vdc to 60Vdc) to drive the winding into saturation. The use of a high DC voltage will quickly drive the winding into saturation and reduce the waiting time for stable readings. A high test current also delivers more accurate readings in noisy environments.
Since the transformer winding is highly inductive, it will store the energy injected into it during testing. This energy must be safely discharged in a controlled way to avoid the risk of injury to test technician as well as damage to the test instrument. For operator safety, this discharge circuit should be built into a transformer winding resistance meter. The test equipment should also provide clear audio and visual warnings to the user.
Vanguardthat featresistanc(20A) andvery largchannelsfurther re
Vanguard(40A). Thbushingsresistanctransform
d Instrumentures dual rece of transfod TRM-40 (4
ge HV transfs can simulteduces the m
d also offershe test terms. The devicece value. Thismer only onc
nts offers thesistance rermers up to
40A). Both dformer windaneously remeasuremen
F
s three-phasminals from t
e will then ins feature redce (Figure 2)
e economicaading chann 200MVA. Fevices empl
dings, providad the HV ant time by a
igure 1. Dua
e winding rehese devicenject the DCduces the te).
TRANS
al WRM-10,nels. The Wor higher teloy a 60Vdc ding fast andand LV windt least 50%
al winding Co
esistance mes can conne test current
esting time b
SFORMER DI
a 10A/36VdRM-10 is cast currents, voltage soud stable reading resistan
onnection
eters, the TRct to all the t to each of
by making co
IAGNOSTIC T
dc winding apable of me
Vanguard orce that can
adings. Dualnces (Figure
RM 203 (20Atransformerthe phases a
onnections to
TESTING R
resistance measuring winffers the TR
n quickly sat resistor rea
e 1). This fea
A) and TRM 4r HV or LV and measureo the
REV 1
2
meter nding M-20 urate ading ature
403
e the
REV 1 T
3
Since a Dthe transthe first ttaken to
Both the This feattest.
For high winding changersdevices, than anyis essent
The Vangtesting ca10 and LTshown inoperatedacross thLTCA conresistancdiagnost
TRANSFORM
DC test curresformer coretime, the exeliminate th
TRM-20/40ure minimiz
voltage tranresistance
s (LTC's). Ththey are sus
y other transial.
guard LTCA-apability on TCA-40 are 1
n figure 3. A d through allhe LTC contantact during ce reading/gic tool for an
MER DIAGNO
Figure
ent is passede will be magcessive in-ru
his remnant
0 and TRM-20es the remn
nsformers wmeter also
hese are thesceptible to sformer com
10 and LTCAthe Load ta
10A and 40 ADC test curr
l taps while tct. The LTCAoperation araph transitnalyzing LTC
OSTIC TESTI
e 2. Three-p
through thegnetized. Whush current mmagnetism.
03/403 havenant magnet
with a load taverify the
e only moviwear and te
mponent, so r
A-40 Load Tap changer oA, respectiverent is injectthe VanguarA can produs shown in fioning from and voltage
NG
hase Windin
e transformehen a magnemay trip the
e built-in traism in the tr
ap changer, continuity ang parts of
ear. In fact, Lregular testi
ap Changer An the transfoely. A typicated through rd LTCA recoce a high re
figure 4. Theone position
e regulator c
ng Connectio
er winding detized-core
e protection
nsformer deransformer c
it is a very dand correcta transform
LTC's result ing to ensure
Analyzers offormer. The tal LTCA-10 tethe LTC con
ords the testsolution res
e user can obn to another
contact issue
on
during the DCHV transformrelays. Step
emagnetizatcore after a
desirable fea operation
mer, and likin more failue reliable an
fer dynamic test current est connecti
ntact. The LTt current andistance wave
bserve the LTr. This is a poes.
C resistancemer is energs should be
tion capabilitDC resistanc
ature that thof the load
ke all mechaures and outnd safe oper
resistance used for LTCon diagram
TC is then d voltage droeform of theTCA contactowerful
test, gized
ties. ce
he DC d tap anical tages
ration
CA -is
op e
The IEEE using thewinding tphase exthe correexcitatioturns ratvoltage in
Figu
C57.12.90 se voltage meturns ratio, a
xcitation testesponding phn current is io testers: An the indust
Figure 3
ure 4. Dynam
standard proethod. Turnsand excitatiot voltage on hase is then then display
ATRT-03 S2, Try (250Vac).
3. Dynamic R
mic Resistanc
ovides the gus ratio tests von current. Athe HV side measured o
yed. VanguaTRF-100 and.
TRANS
Resistance Te
ce Waveform
uidelines forverify the traA typical 3-pof the trans
on the seconrd Instrume
d TRF-250. Th
SFORMER DI
est Connect
m of a Voltag
r measuring ansformer w
phase turns rsformer windndary side. Tnts offers thhe TRF-250 p
IAGNOSTIC T
ions
ge Regulator
transformerwinding confratio tester ading. The ind
The turns rathree 3-phaseprovides the
TESTING R
r
r turns ratiosfiguration, applies a sinduced voltagtio reading ae transformee highest tes
REV 1
4
s
gle ge on nd
er st
REV 1 T
5
A built-inVanguardprovided
The ATRTTRF-250AAC suppl
VanguardS3 (AC po
Phase-shturns ratapplicatiothe transrelationsfigure 6.
TRANSFORM
n thermal prd Turns Ratio
d software.
T-03 S2 and A, respectivey is not avai
d Instrumenower) and A
hifting transfio test. Vangon. The Tri-Psformers. Thhip between
Figur
MER DIAGNO
inter conveno Testers ca
Figure
TRF-250 areely). This allolable.
ts also offerATRT-01B S3
formers are guard InstruPhase generhis device acn the HV and
re 6. Typical
OSTIC TESTI
niently printn be used in
e 5. Thermal
e also availabows users to
rs single pha(AC/Battery
special transments offerates its own
ccurately med LV of the t
Tri-Phase re
NG
s the test ren stand-alone
Printout fro
ble as battero test transfo
se transformy powered).
sformers thas the Tri-Pha
n 3-phase teseasures the transformer.
eport showin
eports on sitee mode or c
om ATRT-03
ry-operated ormers at a c
mer turns rat
at require a ase turns ratst voltage (8turns ratio a Sample test
ng the phase
e for instantan be PC-co
S2
models (ATRconstruction
tio tester mo
3-phase testtio tester for
8Vac, 40Vac, nd the phast results are
e relationshi
t analysis. Alntrolled wit
RT-03A S2 an site when a
odels ATRT-0
t voltage forr this 100Vac) to
se shift shown belo
p
l h the
nd an
01
r the
test
ow in
To get thperformsway to peliminateconductofigure 7.
he most out os as many teerform windes the need ors to carry cThe TSB allo
Fig
of the limiteests as possibding resistanto change tecurrent) andows the sam
ure 7. Trip S
ed time availble. The Vannce tests as west cables bed the lighter e TRM cable
Saver Conne
TRANS
lable during nguard Trip Swell as turnsetween the wgauge cable
es to be used
ctions to TR
SFORMER DI
a transformSaver Box (TSs ratio tests iwinding resi
es of the Turd with the tu
M-403 and A
IAGNOSTIC T
mer outage, aSB) providesin one go. Thstance metens Ratio testurns ratio te
ATRT-03 S2
TESTING R
a user typicas a conveniehe TSB er (heavy gater as shownster.
REV 1
6
ally ent
uge n in
REV 1 TRANSFORMER DIAGNOSTIC TESTING
7
The table below shows the Vanguard offerings for DC winding resistance measurement
Model DC Test Current # Windings Tested Demag Routine
TRM-20 Up to 20A Test two windings Yes
TRM-40 Up to 40A Test two windings Yes
TRM-203 Up to 20A Test three phases Yes
TRM-403 Up to 40A Test three phases Yes
WRM-10 Up to 10A Test two windings No
LTCA-10 Up to 10A Test three phases + LTC diagnostics No
LTCA-40 Up to 40A Test three phases + LTC diagnostics No
The table below shows the Vanguard offerings for turns ratio testing
Model Description Test Voltages Turns Ratio Range
ATRT-01 S3 Single phase 4, 40V 0.8 – 15,000 to 1
ATRT-01B S3 Single phase, Battery Powered 4, 40V 0.8 – 15,000 to 1
ATRT-03 S2 3-phase 8, 40, 100V 0.8 – 15,000 to 1
ATRT-03A S2 3-phase, Battery Power 8, 40, 100V 0.8 – 15,000 to 1
TRF-100 3-phase 4, 40, 100V 0.8 – 50,000 to 1
TRF-250 3-phase 4, 40, 100, 250V 0.8 – 50,000 to 1
Tri-Phase True 3-phase 8, 40, 100V 0.8 – 15,000 to 1
Vanguard Instruments Winding Resistance Meters and Transformer Turns Ratio Testers are housed in field-rugged enclosures and feature rugged membrane keypads for convenient data entry and control. Optional built-in thermal printers are available for field use. All devices can be used in stand-alone mode or can be computer-controlled with the included software.
For further information on Vanguard Instruments' offerings for current transformer testing, please contact our local channel partner or visit our web site at www.vanguard-instuments.com.
1520 S. Hellman Ave • Ontario, CA 91761 • USA
Phone: 909-923-9390 • Fax: 909-923-9391 www.vanguard-instruments.com
Copyright 2016 by Vanguard Instruments Company, Inc.
Transformer Diagnostic Testing • Revision A • June 23, 2016 • JG, HN, TA