Valve_Cast_Steel_Gate_Globe.pdf
Transcript of Valve_Cast_Steel_Gate_Globe.pdf
AUSTRALIAN PIPELINE VALVE
Cast Steel ValvesGate, Globe, Check
Facsimile:
+61-(0)8-8285 0035
Email:
Website:
www.australianpipelinevalve.com.au
™®
© Australian Pipeline Valve 2011
page 2
This page is deliberately left blank.
ContentsFigure Number System
Material Combinations/FeaturesPhysical & Chemical Properties
General Design SpecificationsValve Selection Criteria
Bolted Bonnet Gate Valves OverviewBolted Bonnet Globe Valves OverviewBolted Bonnet Check Valves OverviewPressure Seal Bonnet Valves Overview
Gate Valve - Class 150Gate Valve - Class 300Gate Valve - Class 600Gate Valve - Class 900
Gate Valve - Class 1500Gate Valve (PSB) - Class 900
Gate Valve (PSB) - Class 1500Globe Valve - Class 150Globe Valve - Class 300Globe Valve - Class 600Globe Valve - Class 900
Globe Valve - Class 1500Globe Valve (PSB) - Class 900
Globe Valve (PSB) - Class 1500Swing Check Valve - Class 150Swing Check Valve - Class 300Swing Check Valve - Class 600Swing Check Valve - Class 900
Swing Check Valve - Class 1500Swing Check Valve (PSB) - Class 900
Swing Check Valve (PSB) - Class 1500Stainless Steel Gate Valve - Class 150Stainless Steel Gate Valve - Gate 300
Stainless Steel Globe Valve - Class 150/300Stainless Steel Check Valve - Class 150/300
By-Pass & DrainsSteamco Parallel Slide - Class 150-1500
Steamco Stop Check - Class 150-600Steamco Right Angle Globe - Class 150-600
Steamco Non Return Lift - Class 150-600Flowturn Check Cast Iron - Class 125/250
Flowturn Gate Cast Iron - Class 125/250Flowturn Globe Cast Iron - Class 125/250
Technical Considerations
Page 4-5Page 6-8Page 9Page 10Page 11-12Page 13Page 14Page 15Page 16-19Page 20Page 21Page 22Page 23Page 24Page 25Page 26Page 27Page 28Page 29Page 30Page 31Page 32Page 33Page 34Page 35Page 36Page 37Page 38Page 39Page 40Page 41Page 42Page 43Page 44Page 45Page 46-49Page 50Page 51Page 52Page 53Page 54-55Page 56Page 57
AUSTRALIAN PIPELINE VALVE™®
page 3
Consistent product quality and availability of substantial stocks, makes Australian Pipeline Valve a dependablechoice for cast gate, globe and check valves, where total reliability is the number one concern.
EXAMPLE
Figure Number System
Trim Types
paRt NUmBeR SyStem
AUSTRALIAN PIPELINE VALVE
TRIM CODE
BODY SEAT SURFACE
DISCSURFACE
STEM BACK SEAT(STUFFING BOX)
X F6 F6 F6 F6
U Stellite Stellite F6 F6
XU Stellite F6 F6 F6
P* F304* F304* F304 F304
L* F316* F316* F316 F316
A* Monel* Monel* Monel Monel
N* Alloy 20* Alloy 20* Alloy 20 Alloy 20
H* Hastelloy B* Hastelloy B* Hastelloy B Hastelloy B
Z* Special Special Special Special
B Bronze Bronze Bronze Bronze
* Note if stellite seat then add XU modifier to end, if stellite seat and disc then add U modifier, if PTFE seat add TF modifier.
Suffix denoting operator g = Gear, Blank = Handwheel or N/A
Suffix denoting end connection (Blank is RF, RJ is RTJ, BW is Buttweld, Sp is special drilling, FF = Flat Face)
Suffix denoting bonnet (p is Pressure Seal, W is Welded, Blank is Bolted)
Suffix denoting valve body material (see page 5)
N denotes NACE, Blank is Non NACE
Blank is standard configuration (example solid wedge) F denotes flexible disc Gate p denotes full opening check (API6D) S denotes Parallel Slide D denotes Globe-Stop Check Z denotes C/W Spring R denotes Right Angle
Denotes trim (see below)
Basic model number (As shown in catalogue)
Valve Size (mm)
150 p47 U F N 9 p BW g -
™®
page 4
Figure Number Codes
Comparative Valve Figure Numbers
BODY MATERIAL CODE • BODY/BONNET AND OR CAP MATERIALSSuffix aStm Spec. material
None A216 Gr. WCB Carbon Steel 1 A216 WCC Carbon Steel2 A352 LCC Low Carbon Steel2B A352 LCB Low Carbon Steel 3 A352 LC3 Low Carbon Steel3M A351 CF3M Stainless with Molybdenum (low carbon)4 A217 WC1 Carbon Moly 1/2% Mo4L A352 LC1 Carbon Moly 1/2% Mo5 A217 Gr. C5 5% Cr, 1/2% Mo6 A217 Gr. WC6 1-1/4% Cr, 1/2% Mo8 A351 CF8 Stainless 18% Cr, 8% Ni8C A351 CF8C Stainless 18% Cr, 10% Ni & Cb8M A351 CF8M Stainless with Molybdenum9 A217 Gr. WC9 2-1/4% CR, 1% Mo12 A217 Gr. C12 Chrome Moly 9% Cr, 1% Mo 19 Bronze Bronze B62/LG2/B14820 AL-Bronze Aluminium Bronze0 SPECIAL
VaLVe type CLaSS apV KItZ WaLWORtH CRaNe VeLaN pOWeLL
gate
VaLVeS
150 P47 150SCL 5202F 47 F-0064C 1503
300 P33 300SCL 5206F 33 F-1064C 3003
600 P76 600SCL 5232F 76 F-2064C 6003
900 P83 900SCL 5247F 83 F-7064C 9003
1500 P87 1500SCL 5262F 87 F-3064C 1303
2500 P25 2500SCL 25003
gLOBe
VaLVeS
150 P143 150SCJ 5275F 143 F-0074C 1531
300 P151 300SCJ 5281F 151 F-1074C 3031
600 P171 600SCJ 5295F 171 F-2074C 6031
900 P183 900SCJ 5301F 183 F-7074C 9031
1500 P189 1500SCJ 5308F 189 F-3074C 1311
2500 P25 2500SCJ
SWINg
CHeCK
VaLVeS
150 P147 150SCO 5341F 147 F-0114C 1561
300 P159 300SCO 5344F 159 F-1114C 3061
600 P175 600SCO 5350F 175 F-2114C 6061
900 P187 900SCO 5353F 187 F-7114C 9061
1500 P199 1500SCO 5356F 199 F-3114C 1361
2500 P25 2500SCO
™®
page 5
CAST STEEL GATE VALVES ANSI CLASS 150 ~ 2500
FEATURES
• Bolted bonnet, OS&Y, Flexible wedge.
• On smaller size valves, the yoke is cast integral withbonnet. Larger size valves have two piece yoke, referto individual drawing.
• Stem nut is mounted with ball bearings toreduce operating torque for ease of manualoperation in larger sizes and higher classes.
• Self aligning two piece gland.
AppLICAbLE STANdARdS
• Valves designed to API Std. 600 andBS 1414
• Valves tested to API Std. 598
• Face-to-face to ANSI B16.10
• Flanged ends to ANSI B16.5
• Butt-welding ends to ANSI B16.25
• Trim and seating surface as per API 600 standard.
Material Combinations/Features
MATERIAL LIST
*1 Lantern Ring where applicable
No.part Name
Carbon Steel alloy Steel Stainless Steel
WCB WCC LCB LCC C5 WC6 WC9 CF8 CF8m CF3 CF3m
apV Suffix Code 1 2B 2 5 6 9 8 8m 0 3m
1 Body A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
2 Seat Ring A105 A105 A350 LF2 A350 LF2 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
3 Wedge A216 WCB A216 WCC A352 LCB A217 CF8 A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
4 Stem A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
5 Bonnet Bolt A193 B7 A320 L7 A193 B16 A320 B8 A193 B8M
6 Bonnet Nut A194 2H A194 4 A194 7 A194 8
7 Gasket Solid metal serrated gasket Stainless Steel & Graphite wound Non-metallic gasket Stainless Steel or Soft Iron Ring Gasket
8 Bonnet A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A217 CF8 A351 CF8M A351 CF3 A351 CF3M
9 Back Seat Bushing A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
10 Stem Packing Braided/Flexible Graphite or PTFE
11 Lantern*1 A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 304L A182 F316L
12 Pin Carbon Steel Stainless Steel Alloy Steel
13 Gland A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
14 Gland Flange A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
15 Gland Eyebolt A307 B A307 L7 A193 B7 A193 B8 A193 B8M
16 Gland Nut A194 2H A194 4 A194 8
17 Stem Nut A439D2 (Austenitic DI) ZCuA110Fe3 (AL-Bronze)
18 Retaining Nut Carbon Steel or Alloy Steel
19 Hand Wheel Ductile Iron or Carbon Steel
20 H.W. Lock Nut Carbon Steel Stainless Steel Alloy Steel
21 Yoke A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
22 Nipple Copper Alloy or Carbon Steel or Stainless Steel
23 Seat/Wedge Facing 13Cr or 16Cr-8Ni or HF(Co-CrA) or 316 or 304
™®
page 6
C
B (Open)
A
NPS
CAST STEEL GLObE VALVES ANSI CLASS 150 ~ 2500
FEATURES
• Bolted bonnet, OS&Y, Swivel Disc.
• Plug type disc (Ball type also available).
• On smaller sizes, the yoke is cast integral with bonnet. Larger sizes have two piece yoke, refer to individual drawing.
• Stem nut is mounted with ball bearingsto reduce operating torque for easeof manual operation in larger sizesand higher classes.
AppLICAbLE STANdARdS
• Valves designed to API Std. 600 and BS 1873
• Valves tested to API Std. 598
• Face-to-face to ANSI B16.10
• Flanged ends to ANSI B16.5
• Butt-welding ends to ANSI B16.25
Material Combinations/Features
MATERIAL LIST
*1 Lantern Ring where applicable.
No.part Name
Carbon Steel alloy Steel Stainless Steel
WCB WCC LCB LCC C5 WC6 WC9 CF8 CF8m CF3 CF3m
apV Suffix Code 1 2B 2 5 6 9 8 8m 0 3m
1 Body A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
2 Seat Ring A105 A105 A350 LF2 A350 LF2 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
3 Disc A105 A216 WCC A350 LF2 A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
4 Stem A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
5 Disc Nut A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
6 Gasket Solid metal serrated gasket Stainless Steel & Graphite spiral wound Non-metallic gasket Stainless Steel or Soft Iron Ring Gasket
7 Bonnet A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
8 Bonnet Bolt A193 B7 A320 L7 A193 B16 A320 B8 A193 B8M
9 Bonnet Nut A194 2H A194 4 A194 7 A194 8
10 Back Seat Bushing A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 304L A182 F316L
11 Stem Packing Braided/Flexible Graphite or PTFE
12 Lantern*1 A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
13 Pin Carbon Steel Stainless Steel Alloy Steel
14 Gland Flange A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
15 Gland A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
16 Gland Eyebolt A307 B A307 L7 A193 B7 A193 B8 A193 B8M
17 Gland Nut A194 2H A194 4 A194 8
18 Stem Nut A439D2 (Austentic DI) ZCuA110Fe3 (AL-Bronze)
19 Handwheel Ductile Iron or Steel
20 H.W. Lock Nut Carbon Steel Stainless Steel Alloy Steel
21 Seat/Disc Facing 13Cr or 16Cr-8Ni or HF(Co-CrA) ST#6 or 316 or 304
™®
page 7
B
(Open)
A
NPS
C
CAST STEEL ChECk VALVESANSI CLASS 150 ~ 2500
FEATURES
• Bolted cover
• Swing disc
AppLIC AbLE STANdARdS
• Valves designed to API Std. 600 6D and BS 1868
• Valves tested to API Std. 598
• Face-to-face to ANSI B16.10
• Flanged ends to ANSI B16.5
• Butt-welding ends to ANSI B16.25
• Trim and seating surface as per API 600 standard.
Material Combinations/Features
MATERIAL LIST
The material is according to ASTM standard.* Eye bolt supplied in larger sizes & higher classes.
No.part Name
Carbon Steel alloy Steel Stainless Steel
WCB WCC LCB LCC C5 WC6 WC9 CF8 CF8m CF3 CF3m
apV Suffix Code 1 2B 2 5 6 9 8 8m 0 3m
1 Body A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
2 Seat Ring A105 A105 A350 LF2 A350 LF2 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
3 Disc A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
4 Disc Nut A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
5 Hinge A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
6 Hinge Pin A182 F6 A182 F6 A182 F6 A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
7 Gasket Solid metal serrated gasket Stainless Steel & Graphite spiral wound Non-metallic gasket Stainless Steel or CAD Plated Soft Iron Ring Gasket
8 Cover A216 WCB A216 WCC A352 LCB A352 LCC A217 C5 A217 WC6 A217 WC9 A351 CF8 A351 CF8M A351 CF3 A351 CF3M
9 Cover Bolt A193 B7 A320 L7 A193 B16 A193 B8 A193 B8M
10 Cover Nut A194 2H A194 4 A194 7 A194 8
11 Washer Carbon Steel or Alloy Steel or Stainless Steel
12 Seat/Disc Facing 13Cr or 16Cr-8Ni or HF(Co-CrA) ST#6 or 316 or 304
13 Eye Bolt* A193 B7 A320 L7
™®
page 8
A
BN
PS
Physical & Chemical Properties
mateRIaLS
FeRRItIC SteeLSCHemICaL ReQUIRemeNtS (%) meCHaNICaL pROpeRtIeS
Carbon manganese phos- Sulphur Silicon Nickel Chromium molyb- tensile yield elongation Reduction
phorous denum Strength Strength 2” (50mm) of area
N/mm2 N/mm2
CaSt CaRBON SteeL aStm a216, grade WCB
Min - - - - - - - - 485 205 22% 35%
Max 0.35 1.00 0.040 0.045 0.60 - - - 655 - - -
FORgeD CaRBON SteeL aStm a105
Min - 0.60 - - - - - - 485 250 22% 30%
Max 0.35 1.05 0.040 0.05 0.35 - - - - - - -
CaSt CaRBON SteeL FOR LOW tempeRatUReS aStm a352, grade LCB*
Min - - - - - - - - 450 240 24% 35%
Max 0.30 1.00 0.040 0.045 0.60 - - - 620 - - -
CaSt CaRBON mOLy SteeL FOR LOW tempeRatUReS aStm a352, grade LC1*
Min - 0.50 - - - - - 0.45 450 240 24% 35%
Max 0.25 0.80 0.040 0.045 0.60 - - 0.65 620 - - -
CaSt 21⁄2% NICKeL SteeL FOR LOW tempeRatUReS aStm a352, grade LC2*
Min - 0.50 - - - 2.0 - - 485 275 24% 35%
Max 0.25 0.80 0.040 0.045 0.60 3.0 - - 655 - - -
CaSt 31⁄2% NICKeL SteeL FOR LOW tempeRatUReS aStm a352, grade LC3*
Min - 0.50 - - - 3.0 - - 485 275 24% 35%
Max 0.15 0.80 0.040 0.045 0.60 4.0 - - 655 - - -
CaSt CaRBON mOLy SteeL aStm a217, grade WCI
Min - - - - - - - 0.45 450 240 24% 35%
Max 0.25 0.80 0.040 0.045 0.60 - - 0.65 620 - - -
CaSt 11⁄4% CR - 1⁄2% mO aLLOy SteeL aStm a217, grade WC6
Min - 0.50 - - - - 1.0 0.45 485 275 20% 35%
Max 0.20 0.80 0.040 0.045 0.60 - 1.50 0.65 655 - - -
CaSt 21⁄4% CR - 1% mO aLLOy SteeL aStm a217, grade WC9
Min - 0.40 - - - - 2.0 0.9 485 275 20% 35%
Max 0.18 0.70 0.040 0.045 0.60 - 2.75 1.20 655 - - -
CaSt 1 - 6% CR aLLOy SteeL aStm a217, grade C5
Min - 0.40 - - - - 4.0 0.45 620 415 18% 35%
Max 0.20 0.70 0.040 0.045 0.75 - 6.50 0.65 795 - - -
CaSt 9% CR - 1% mO aLLOy SteeL aStm a217, grade C12
M in - 0.35 - - - - 8.0 0.9 620 415 18% 35%
M ax 0.20 0.65 0.040 0.045 1.00 - 10.00 1.20 795 - - -
CaSt 12 - 14% CR aLLOy SteeL aStm a217, grade Ca15
Min - - - - - - 11.5 - 620 450 18% 30%
M ax 0.15 1.00 0.040 0.030 1.50 1.0 14.0 0.50 795 - - -
FORgeD/ROLLeD 12 - 14% CR aLLOy SteeL aStm a182, grade F6a
Min - - - - - - 11.5 - 760 585 15% 35%
Max 0.15 1.00 0.040 0.030 1.00 0.50 13.5 - - - - -
*Usual minimum service temperature : LCB at -46°C (-50°F), LCI at -60°C (-75°F), LC2 at -75°C (100°F), LC3 at -100°C (-150°F)
aUSteNtIC SteeLS
CHemICaL ReQUIRemeNtS (%) meCHaNICaL pROpeRtIeS
Carbon manganese phos- Sulphur Silicon Nickel Chromium molyb- tensile yield elongation Reduction
phorous denum Strength Strength 2” (50mm) of area
N/mm2 N/mm2
CaSt StaINLeSS SteeL WItH mOLyBDeNUm (LOW CaRBON) aStm a351, grade CF3m
Min - - - - - 9.0 17.0 2.0 485 205 30% -
Max 0.03 1.50 0.040 0.040 1.50 13.0 21.0 3.0 - - - -
CaSt StaINLeSS SteeL WItH mOLyBDeNUm aStm a351, grade CF8m
Min - - - - - 9.0 18.0 2.0 485 205 30% -
Max 0.08 1.50 0.040 0.040 1.50 12.0 21.0 3.0 - - - -
CaSt StaINLeSS SteeL WItH COLUmBIUm (NIOBIUm) aStm a351, grade CF8C
Min - - - - - 9.0 18.0 - 485 205 30% -
Max 0.08 1.50 0.040 0.040 2.00 12.0 21.0 0.50 - - - -
ASTM A351-CF8C shall have a columbium content of not less than 8 times the carbon content but not over 1.00%
™®
page 9
API 600 Cast Steel Valves
General Design Specifications
Cast steel valves are designed and manufactured to conform with API, ASTM,ANSI and other applicable internationally recognised standards, to possess all the qualities to meet with stringent requirement criteria of petroleum, petro-chemical and general industrial applications.
Valves are tested in accordance with applicable API standards. Full traceability is maintained.
Valves offer the option of hard facing on the wedge (disc) and seating areas.Lantern rings are furnished as a standard on gate valves of class 300 and above inlarger sizes.
Gate Valves are optionally available with lantern rings. Alongside are illustrations of lantern rings as well as disc connection.
ameRICaN StD. BRItISH StD.
BS1414 (Gate Valve) BS1873 (Globe Valve) BS1868 (Check Valve)
Shell wall thickness and general valve design specifications API 600
Pressure-temperature ratings ANSI B16.34 BS1560
Face-to-face dimensions ANSI B16.10 BS2080 End-to-end dimensions
End flange dimensions ANSI B16.5* BS1560 Gasket contact facing
BS1414 (Gate Valve) BS1873 (Globe Valve) BS1868 (Check Valve)
Welding end dimensions ANSI B16.25
*Valves 28” and larger according to MSS SP-44 or API 605 are available.
™®
page 10
Valve Selection Criteria
Gate Valves
Gate valves are used for bi-directional shut off applications where minimum
pressure drop is required. They are not designed for throttling service.
Gear operators, actuators, by-passes, actuators etc, can be fitted on request.
Parallel slide style also available.
Globe Valves
Globe valves are ideal for throttling and shut off. They can be used for shut
off service, but do have a higher pressure drop than gate valves. Globe
valves should not be used for prolonged throttling at less than 10% open.
Gearboxes, actuators, bypasses etc, can be fitted.
Ratings
Valves must only be used in operating conditions within the correct ANSI
pressure-temperature ratings for valve class rating and body/bonnet
material.
Temperature Limitations
Only use valves within the correct temperature limitations of their con-
struction. Temperature limitations of body/bonnet materials, trim, bolting,
packing and gaskets must all be considered.
™®
page 11
Valve Selection Criteria
Stop Check Valves
Stop check valves are combination globe and check valves. In the open
position, they function as a lift check valve valve. In the closed position, they
are seated by manually closing the stem like a globe valve. Stop check
valves must be installed vertically (in a horizontal pipeline). They provide
positive shutoff in either direction when the stem is in the closed position.
Right angle style are also available.
Swing Check Valves
Swing check valves are used to prevent flow reversal. They are suitable for
service in horizontal or upwards vertical. They have low pressure drop and
are best suited for moderate velocity applications. Either too low a line
velocity or too high a velocity can damage valve internals and shorten valve
life hence correct size selection is important. Service in systems involving
rapid and frequent flow reversals, pulsation or turbulent flow should be
avoided. Also API6D full opening (piggable) type available on request.
™®
page 12
Bolted Bonnet Gate Valves
Features
Full body wedge guides allow correct wedge alignment. Yoke sleeve with
bearings reduce torque for easy operation. Seat rings allow easy access for
maintenance and packing replacement is simple.
Soft seated trim option
All gate valves are available with optional PTFE seat rings. The molded PTFE
ring is bonded into a seat ring groove in the face for maximum service life.
This design is excellent for lower temperature service where tight shutoff is
required.
Parallel slide style also available, see page 46 - 49. 1. handw heel
2. Ris ing Stem - provides open-close indication
3. Grease Fitt ing - to minimise wear and operating torque
4. Yoke Sleeve - furnished in ductile Ni-resist or aluminum-bronze for low torque operation
5. Swing bolt - easier maintenance and packing replacement
6. Gland - flange is self-aligning to eliminate stem damage
7. Stuf fing b ox
8. Stem - upset forge T-head stems to eliminate possibility of abent stem jamming the valve
9. backseat - provides back-up stem seal.
10. bonnet Joint
11. body - full ported, heavy wall body API 600 wall thickness
12. Wedge - heavy pattern. Available in solid & flex wedge
13. Seat Ring - full ported rings for easy maintenance.
14. End Connections - flanged or butt weld ends
Grease injector and lantern ring option
Soft seated “ST” trim option
2
1
3
5
7
9
11
13
4
6
8
10
12
14
™®
page 13
Bolted Bonnet Globe Valves
Operation
Seat rings are easily accessible for repair or replacement. Packing bolts on
most valves simplify packing replacement. Australian Pipeline Valve globe
valves are for services requiring frequent operation and throttling where
pressure drop across the valve is about 20%. Closer throttling, can result in
higher pressure drops which may cause excessive velocities or cavitation
and could cause vibration or high noise levels resulting in damage to the
valve or adjacent components/structure.
Life
Heavy construction provides years of reliable service.
design
Available in bolted and pressure seal bonnet, outside screw and yoke, rising
stem with ball or plug type disc, and have flanged or butt weld ends.
Standards
BS 1873 and ANSI B16.34. Dimensions to ANSI B16.10, BS 2080 and ISO
5752. Wall thickness complies with API 600. 1. Yoke Sleeve - furnished in aluminum-bronze to
reduce torque. Larger sizes furnished with bearings.
2. handwheel
3. Swing bolts - easier maintenance
4. Gland - self-aligning to eliminate stem damage
5. Stuf fing box
6. Stem - heavy duty
7. backseat - provides back-up stem seal
8. bonnet Joint - ring joint or spiral according to ANSIclass
9. Seat Rings - separate heavy duty, full ported rings foreasy maintenance.
10. disc - heavy duty disc plug design
11. End Connections - flanged or butt weld ends
12. body - full ported, with API 600 heavy wall thickness
2
1
3
5
7
9
11
4
6
8
10
12
™®
page 14
Bolted Bonnet Check Valves
Australian Pipeline Valve valves are designed to provide fast valve action and
maximum life. All valves are full ported, have full API 600 wall thickness, and
meet the requirements of ANSI B16.34. Full opening API6D (piggable) type
also available on request.
Features
Valves are designed to close quickly in either horizontal or vertical (flow
up) pipe runs. The body seat ring is installed on a 3o angle. This allows our
check valve to close even when installed in horizontal pipe run with no
pressure.
1. disc Stop - provides positive stop in open position
2. bonnet Joint - (ring or spiral according to class)
3. hinge pin - solid pin for maximum strength
4. Securing Lugs - allow disc to seat freely and preventdisc spinning
5. hinge - designed to withstand shock and load of quickclosing
6. disc - disc is bolted and pinned to hinge; ground seat-ing surface is mated to seat ring for positive shutoff.
7. Seat Ring - Full port seal welded or screwed
8. End Connections - flanged or buttweld
2
1
3
5
7
4
6
8
™®
page 15
Pressure Seal Bonnet Valves
Flexible Wedge Gate Valve
The wedge is a one piece, fully guided wedge. Available in flex wedge and
solid wedge. (Flexible wedge allows the seating faces to move to compen-
sate for thermal expansion). Wedging actions allows a tight seal even in low
differential pressure services. Flexible wedge construction resists wedge
sticking in service where the valve may be closed when hot and opened
when cold. Seating surfaces are hardfaced for long life.
Parallel slide also available, see page 17 and 46 - 49.
1. Yoke Sleeve - aluminum-bronze yoke sleeve has thrustbearings to minimise torque.
2. hand Wheel - (or gear in larger sizes)
3. Yoke - offering ease of maintenance
4. Stem - The design allows the wedge to self-align, eliminatingthe possibility of jamming the wedge.
5. Gland - two piece, self-aligning gland eliminates cocking.Swing out bolting facilitates maintenance.
6. back Seat - Integral, hardfaced
7. pressure Seal - retaining ring and mild steel silver platedgasket to aid disassembly and provide maximum seal.
8. Seat Ring - hardfaced seat rings are welded to body.Tapered design provides clear flow path.
9. Wedge - one-piece, fully guided. Parallel seat also available.
10. body - streamlined flow path minimises pressure drop. API 600 wall thickness.
2
1
3
5
7
9
4
6
8
10
11. Segment RIng
12. Thrust RIng
13. Gasket
14. body
15. bonnet
Flexible Wedge
Exploded View
See E xploded v iew
™®
page 16
Pressure Seal Bonnet Valves
parallel Sl ide Gate Valves
Normally utilised for shut off service but are not recommended for
throttling. Gate valves are normally installed in horizontal pipe runs with
the valve stem vertically up. They can be installed in horizontal or vertical
pipe runs. After closing with sufficient force, the stem should be backed off
slightly (1/8 turn) to relieve stem load. Parallel Slide Valves have self aligning
discs with no wedging force and react freely to thermal changes. The design
also ensures uniform seat wear and ease of maintenance. Parallel Slide Gate
Valves are ideal where high differential pressure or thermal expansion may
cause sticking of wedge to gate in traditional gate valves.
2
1
3
5
7
9
4
6
8
10
1. Yoke Sleeve - aluminum-bronze yoke sleeve with thrust bearings for ease of opening.
2. Actuation - Low torque seating design reduces actuationcosts.
3. Yoke - designed to offer ease of maintenance
4. Stem - Threaded into disc housing and also pinned.
5. Gland - two piece, self-aligning gland eliminates cocking. Swingout bolting facilitates maintenance.
6. back Seat - Integral, hardfaced
7. pressure Seal - retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum seal.
8. Seat Ring - hardfaced seat rings are welded to body and aredesigned for ease of maintenance.
9. discs - Spring loaded discs are self-aligning and reduce actuator torque requirements.
10. Integral Stop - Integral stop positions for reliable seating.
™®
page 17
Pressure Seal Bonnet Valves
Globe & SdNR Check Valves
Australian Pipeline Valve Globe valves are installed with pressure and flow
under the disc. Globe valves are suitable for most throttling applications;
they should not be used for throttling at less than 10% open. Stop Check
Valves have a guided loose disc allowing the valve to act as a combination
globe valve and check valve.
2
1
3
5
7
9
4
6
8
10
1. Yoke Sleeve - aluminum-bronze yoke sleeve minimizesoperating torque. Larger sizes have needle bearing typethrust bearings.
2. Actuation - Manual handwheel gear operator or actuated.
3. Yoke - designed to offer ease of maintenance.
4. Stem - precision-ground stem has upset tee-head for reliable stem/wedge connection.
5. Gland - two piece, self-aligning gland eliminates cocking.Swing out bolting facilitates maintenance.
6. back Seat - Integral, hardfaced
7. pressure Seal - uncomplicated design has segmentedretaining ring and mild steel silver plated gasket to aid disas-sembly and provide maximum bonnet seal.
8. hardened Seating Surfaces - both disc and body seatingsurfaces are hard faced for maximum service life.
9. d isc - fully body guided for positive seating.
10. body - Full port ‘s’ pattern design available to minimisepressure drop.
™®
page 18
Pressure Seal Bonnet Valves
Tilt & piston Check Valves
Australian Pipeline Valve Check valves are installed with pressure and flow
under the disc.
2
1
3
4
1. pressure seal design - with retaining ring.
2. Guided disc - for positive seating.
3. Welded in - hardfaced seat ring.
4. Ful l port - S pattern flow path available to minimisepressure drop.
™®
page 19
Gate ValveCat P47Class 150
dIMENSIONS (MM)
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr. 410 or A182 Gr. F6a
Yoke Sleeve Ductile Iron or Bronze A439 Gr. D2C or B62
Sleeve Gland Carbon Steel A216 Gr. WCB
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Wheel Nut Carbon Steel A105
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Bearing - Thrust Ball
Grease Nipple Carbon Steel A307 Gr. B
Set Screw Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Spiral Wound 304/316 Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5/26” & larger MSS SP-44
Basic Design API 600
Testing API 598
Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF 165 178 190 203 229 268 292 330 356 381 406
A. End to End BW 165 216 241 283 305 403 419 457 502 571 610
B. Valve Open 365 390 435 511 610 765 978 1146 1372 1587 1759
C. Hand Wheel Dia 229 229 229 254 305 356 406 457 508 559 559
Weight (Kg) RF * 20 24 28 30 50 85 127 195 283 450 560
For 1⁄2” to 1” dimensions see page 41 and detailed overview brochure.
Size (in) 18” 20” 22” 24” 26” 28” 30” 32” 36” 42” 48”
A. Face to Face RF 432 457 508 508 559 610 610 660 711 787 914
A. End to End BW 660 711 762 813 864 914 914 965 1016 1092 -
B. Valve Open 1930 2156 2346 2515 2721 2896 3130 3264 3588 4610 4842
C. Hand Wheel Dia 559 610 660 660 813 813 813 815 813 813 -
Weight (Kg) RF * 700 900 1050 1350 2000 2400 2800 3400 3820 5900 7300
For 1⁄2” to 1” dimensions see page 41 and detailed overview brochure.For CF8/CF8M 150lb gate see page 41.* For Buttweld weights see detailed overview brochure.
Full Port Design
™®
page 20
A
C
B
Gate ValveCat P33Class 300
dIMENSIONS (MM)
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr. 410 or A182 Gr. F6a
Yoke Sleeve Ductile Iron or Bronze A439 Gr. D2C or B62
Sleeve Gland Carbon Steel A216 Gr. WCB
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Wheel Nut Carbon Steel A105
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Bearing - Thrust Ball
Grease Nipple Carbon Steel A307 Gr. B
Set Screw Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Spiral Wound 304/316 Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600
Testing API 598
Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF 190 216 241 283 305 403 419 457 502 762 838
A. End to End BW 190 216 241 283 305 403 419 457 502 762 838
B. Valve Open 365 429 457 527 619 829 1025 1213 1473 1289 1784
C. Hand Wheel Dia 229 229 229 254 305 406 457 508 559 559 559
Weight (Kg) RF * 20 24 44 50 74 137 217 337 580 715 1050
For 1⁄2” to 1” dimensions see page 42 and detailed overview brochure.
Size (in) 18” 20” 24”
A. Face to Face RF 914 991 1143
A. End to End BW 914 991 1143
B. Valve Open 1965 2194 2578
C. Hand Wheel Dia 610 660 660
Weight (Kg) RF * 1235 1655 2320
For RTJ & 5” dimensions see detailed overview brochure.For CF8/CF8M 300Lb gate see page 42.* For Buttweld weights see detailed overview brochure.
Full Port Design
™®
page 21
A
B
C
Gate ValveCat P76Class 600
dIMENSIONS (MM)
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr. 410 or A182 Gr. F6a
Yoke Sleeve Ductile Iron or Bronze A439 Gr. D2C or B62
Sleeve Gland Carbon Steel A216 Gr. WCB
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Wheel Nut Carbon Steel A105
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Bearing - Thrust Ball
Grease Nipple Carbon Steel A307 Gr. B
Set Screw Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Metal Ring Joint or Spiral Wound SS Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600
Testing API 598
Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF 241 292 330 356 432 559 660 787 838 889 991
A. Face to Face RTJ 241 390 333 359 435 562 664 790 841 892 994
A. End to End BW 241 292 330 356 432 559 660 787 838 889 991
B. Valve Open 362 387 457 514 638 838 1029 1270 1486 1667 1832
C. Hand Wheel Dia 229 229 254 305 406 508 559 559 610 660 660
Weight (Kg) RF 35 48 60 85 135 325 515 840 1100 1360 1910
Weight (Kg) BW 22 38 45 70 105 265 380 700 925 1240 1580
Size (in) 18” 20” 24”
A. Face to Face RF 1092 1194 1397
A. Face to Face RTJ 1095 1197 1400
A. End to End BW 1092 1194 1397
B. Valve Open 2013 2331 2610
C. Hand Wheel Dia 813 813 813
Weight (Kg) RF 2335 2750 4450
Weight (Kg) BW 1900 2150 3660
For 5” and 26” to 36” dimensions see detailed overview brochure.
Full Port Design
™®
page 22
A
B
C
Gate ValveCat P83Class 900
dIMENSIONS (MM)
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Carbon Steel A106 + Stellite/HF
Back Seat Ring Stainless Steel A182 Gr. F6a
Yoke Sleeve Ductile Iron or Bronze A439 Gr. D2C or B62
Sleeve Gland Carbon Steel A216 Gr. WCB
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Wheel Nut Carbon Steel A105
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7/B7M
Gland Nut Carbon Steel A194 Gr. 2H.2HM
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Bearing - Thrust Ball
Grease Nipple Carbon Steel A307 Gr. B
Set Screw Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Metal Ring Joint or Spiral Wound SS, Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600, ANSI B16.34
Testing API 598
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130 1219
A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140 1232
B. Valve Open 660 702 800 902 1121 1470 1571 1715 1880 2067 2267
C. Hand Wheel Dia 356 406 356 559 610 813 610 610 610 760 -
Weight (Kg) RF 100 140 120 190 460 860 1050 1600 2220 3000 3870
Weight (Kg) BW 80 120 110 180 400 710 830 1350 1890 2565 3300
Size (in) 20”
A. Face to Face RF 1321
A. Face to Face RTJ 1333
B. Valve Open 2440
C. Hand Wheel Dia 760
Weight (Kg) RF 4860
Weight (Kg) BW 4050
For 5” and 24” dimensions & weights see detailed overview brochure.
*10” and over sizes are according to ANSI B16.34
Note: 900LB 2” & 21⁄2“ are the same as 1500LB 2” & 21⁄2”
Full Port Design
™®
page 23
A
B
C
Gate ValveCat P87Class 1500
dIMENSIONS (MM)
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Carbon Steel A106 + Stellite/HF
Back Seat Ring Stainless Steel A182 Gr. F6a
Yoke Sleeve Ductile Iron or Bronze A439 Gr. D2C or B62
Sleeve Gland Carbon Steel A216 Gr. WCB
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Wheel Nut Carbon Steel A105 Zn. Plating
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7/B7M
Gland Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Bearing - Thrust Ball
Grease Nipple Carbon Steel A307 Gr. B
Set Screw Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Metal Ring Joint or Sprial Wound SS Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600, ANSI B16.34
Testing API 598
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF/BW 368 419 470 546 705 832 991 1130 1257 1384 1537
A. Face to Face RTJ 371 422 473 549 711 841 1000 1146 1276 1407 1559
B. Valve Open 590 702 781 879 1181 1343 1511 1711 1880 2067 2267
C. Hand Wheel Dia 356 406 406 559 610 813 915 915 915 - -
Weight (Kg) RF 100 140 180 340 700 1211 2092 2951 4382 6950 9000
Weight (Kg) BW 90 130 160 240 590 986 1765 2586 3659 6000 7740
Size (in) 20”
A. Face to Face RF 1664
A. Face to Face RTJ 1686
A. Short Pattern End to End BW 1473
B. Valve Open 2440
C. Hand Wheel Dia -
Weight (Kg) RF 11130
Weight (Kg)Short PatternBW -
Long Pattern BW 9560
For 5” and 24” dimensions & weights see detailed overview brochure.
*10” and over sizes are according to ANSI B16.34
Full Port Design
™®
page 24
A
B
C
Gate Valve (Pressure Seal)Cat P83Class 900
dIMENSIONS (MM)
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Carbon Steel A106 + Stellite/HF
Yoke Sleeve Ductile Iron or Bronze A439 Gr. D2C or B62
Sleeve Gland Carbon Steel A216 Gr. WCB
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Wheel Nut Carbon Steel A105
Bonnet Bolt Carbon Steel A193Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Bearing - Thrust Ball
Grease Nipple Carbon Steel A307 Gr. B
Set Screw Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Soft Metal Ring CAD Plated
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600, ANSI B16.34
Testing API 598
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130 1219
A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140 1232
A. Short Pattern End to End BW 216 254 305 356 508 660 787 914 991 1092 -
B. Valve Open 660 702 690 902 1121 1470 1571 1715 1880 2067 2267
C. Hand Wheel Dia 356 406 356 457 610 610 610 610 610 760 -
Weight (Kg) Short Pattern BW 60 90 80 130 340 590 690 1150 1590 2290 3200
Weight (Kg) Long Pattern BW 66 102 100 150 364 621 739 1295 1790 2465 3200
Weight (Kg) Long Pattern RF 110 140 120 190 460 800 1000 1545 2100 2900 3700
Size (in) 20”
A. Face to Face RF/BW 1321
A. Face to Face RTJ 1333
A. Short Pattern End to End BW -
B. Valve Open 760
C. Hand Wheel Dia -
Weight (Kg)Short PatternBW 3636
Weight (Kg)Long PatternBW 4050
Weight (Kg) RF 4860
For 5” and 24” (Long Pattern) dimensions see detailed overview brochure.
*Note: 10” and over sizes are according to ANSI B16.34
Note: 900LB 2” & 21⁄2“ are the same as 1500LB 2” & 21⁄2”
Full Port Design
™®
page 25
A
C
B
Gate Valve (Pressure Seal)Cat P87Class 1500
dIMENSIONS (MM)
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Carbon Steel A106 + Stellite/HF
Yoke Sleeve Ductile Iron or Bronze A439 Gr. D2C or B62
Sleeve Gland Carbon Steel A216 Gr. WCB
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Wheel Nut Carbon Steel A105 Zn. Plating
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7/B7M
Gland Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Bearing - Thrust Ball
Grease Nipple Carbon Steel A307 Gr. B
Set Screw Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Soft Metal Ring CAD Plated
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600, ANSI B16.34
Testing API 598
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF/BW 368 419 470 546 705 832 991 1130 1257 1384 1537
A. Face to Face RTJ 371 422 473 549 711 841 1000 1146 1276 1407 1559
A. Short Pattern End to End BW 216 254 305 406 559 711 864 991 1167 1194 1346
B. Valve Open 590 702 781 879 1181 1343 1511 1711 1880 2067 2267
C. Hand Wheel Dia 356 406 457 559 610 760 813 813 - - -
Weight (Kg) Short Pattern BW 60 120 99 200 480 870 1490 2128 2800 5200 6400
Weight (Kg) Long Pattern BW 80 130 140 240 560 940 1640 2560 3200 6000 7740
Weight (Kg) Long Pattern RF 110 150 195 340 735 1180 2128 2990 4115 6950 9000
Size (in) 20”
A. Face to Face RF/BW 1664
A. Face to Face RTJ 1680
A. Short Pattern End to End BW 1473
B. Valve Open 2440
C. Hand Wheel Dia -
Weight (Kg)Short PatternBW 7980
Weight (Kg)Long PatternBW 9560
Weight (Kg) RF 11130
For 5” and 24” (Long Pattern) dimensions see detailed overview brochure.
*Note: 10” and over sizes are according to ANSI B16.34
™®
page 26
Full Port Design
A
C
B
Globe ValveCat P143Class 150
Full Port Design
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr.410 or A182 Gr. F6a
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Disc Gland Stainless Steel A217 Gr. CA-15
Yoke Bush Ductile Iron or Bronze A439 Gr. D2C or B62
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr.B7
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Wheel Nut Stainless Steel A192 Gr. 8/A105
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Spiral Wound 304/316 Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600*
Testing API 598
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF 203 216 241 292 406 495 622 698.5 787 914
A. End to End BW 203 216 241 292 406 495 622 698.5 787 914
B. Valve Open 330 365 413 463 536 616 746 832 1375 1569
C. Hand Wheel Dia 203 229 254 305 356 406 559 559 600 600
Weight (Kg) RF 20 26 35 65 113 190 238 410 560 890
Weight (Kg) BW 18 22 28 55 93 170 215 370 500 795
For RTJ dimensions and 5” dimensions, see detailed overview brochure.For 1/2” to 1 1/2” see page 43 and detailed overview brochure.For CF8/CF8M Globe 150Lb see page 43.
*Stem is Based on B.S 1873
™®
page 27
A
B
C
Globe ValveCat P151Class 300
Full Port Design
dIMENSIONS (MM)
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr.410 or A182 Gr. F6a
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Disc Gland Stainless Steel A217 Gr. CA-15
Yoke Bush Ductile Iron or Bronze A439 Gr. D2C or B62
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr.B7/2HM
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Wheel Nut Stainless Steel A194 Gr. 8/A105
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Spiral Wound 304/316 Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600*
Testing API 598
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF 267 292 317 356 444 559 622 711 838 863
A. End to End BW 267 292 317 356 444 559 622 711 838 863
B. Valve Open 356 400 448 537 625 800 990 1170 1380 1480
C. Hand Wheel Dia 205 229 254 305 406 559 559 559 700 -
Weight (Kg) RF 30 37 60 90 176 333 340 550 765 1100
Weight (Kg) BW 25 30 52 75 150 320 280 520 - -
For RTJ dimensions 2” - 16” and 5” RF/RTJ dimensions, see detailed overview brochure.For 1⁄2” to 11⁄2” see page 43 and detailed overview brochure. For CF8/CF8M Globe 300# see page 43.
*Stem is Based on B.S 1873
™®
page 28
A
B
C
Globe ValveCat P171Class 600
Full Port Design
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr.410 or A182 Gr. F6a
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Disc Gland Stainless Steel A217 Gr. CA-15
Yoke Bush Ductile Iron or Bronze A439 Gr. D2C or B62
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Wheel Nut Stainless Steel A194 Gr. 8/A105
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Metal Ring Joint or Spiral Wound SS Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600*
Testing API 598
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF 292 330 356 432 559 660 787 838 889 991
A. Face to Face RTJ 295 333 359 435 562 663 790 841 892 994
A. End to End BW 292 330 356 432 559 660 787 838 892 994
B. Valve Open 425 438 546 663 889 997 865 1101 1426 1431
C. Hand Wheel Dia 254 305 356 457 559 660 610 660 - -
Weight (Kg) RF 39 56 68 121 280 450 720 950 1750 2260
Weight (Kg) BW 35 44 59 97 230 380 580 830 - -
For 1⁄2” to 11⁄2” see detailed overview brochure.
*Stem is Based on B.S 1873
™®
page 29
A
B
C
Globe ValveCat P183Class 900
Full Port Design
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr.410 or A182 Gr. F6a
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Disc Gland Stainless Steel A217 Gr. CA-15
Yoke Bush Ductile Iron or Bronze A439 Gr. D2C or B62
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Wheel Nut Stainless Steel A194 Gr. 8/A105
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Metal Ring Joint or Spiral Wound SS Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600*
Testing API 598
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130
A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140
A. Short Pattern End to End BW 216 254 305 256 508 660
B. Valve Open 597 648 724 832 1019 1181 1540 1840 2135 2380
C. Hand Wheel Dia 406 457 457 559 750 750 750 - - -
Weight (Kg) Short Pattern BW 60 85 80 130 229 1110
Weight (Kg) Long Pattern BW 73 110 95 150 310 1225 1345 1900 2130 2860
Weight (Kg) Long Pattern RF 98 130 110 180 440 1346 1400 2220 2650 3300
Note:- 900LB 2” & 21⁄2” are the same as 1500LB 2” & 21⁄2”Parabolic disc for low torqueFor 1⁄2” to 11⁄2” dimensions see detailed overview brochure.
*Stem is Based on B.S 1873
™®
page 30
A
B
C
Globe Valve Cat P189Class 1500
Full Port Design
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Carbon Steel A276 Gr.410 or A182 Gr. F6a
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Disc Gland Stainless Steel A217 Gr. CA-15
Yoke Bush Ductile Iron or Bronze A439 Gr. D2C or B62
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Carbon Steel A193 Gr. B7
Gland Nut Carbon Steel A194 Gr. 2H
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Wheel Nut Stainless Steel A194 Gr. 8/A105
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Metal Joint or Spiral Wound SS Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600*
Testing API 598
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12”
A. Face to Face RF/BW 368 419 470 546 705 832 991 1130
A. Face to Face RTJ 371 422 473 549 708 835 1000 1146
A. Short Pattern End to End BW 216 254 305 406 559 711
B. Valve Open 597 648 724 816 1019 1181 1610 1950
C. Hand Wheel Dia 406 457 559 610 813 - - -
Weight (Kg) Short Pattern BW 60 85 120 220 490 1150
Weight (Kg) Long Pattern BW 98 130 170 255 590 1290 1700 2600
Weight (Kg) Long Pattern RF 73 110 140 230 540 1190 1480 2300
Parabolic disc for low torqueFor 1⁄2” to 11⁄2” dimensions see detailed overview brochure.
*Stem is based on B.S. 1873
™®
page 31
A
B
C
Globe Valve(Pressure Seal Bonnet)Cat P183Class 900
Full Port Design
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr.410 or A182 Gr. F6a
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Disc Gland Stainless Steel A217 Gr. CA-15
Yoke Bush Ductile Iron or Bronze A439 Gr. D2C or B62
Gland Bolt Carbon Steel A193 Gr. B7/B7M
Gland Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Wheel Nut Stainless Steel A194 Gr. 8/A105
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Soft Metal Ring CAD Plated
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600*
Testing API 598
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130
A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140
A. Short Pattern End to End BW 216 254 305 356 508 660
B. Valve Open 597 648 724 832 1019 1181 1540 1840 2135 2380
C. Hand Wheel Dia 406 457 559 610 813 813 - - - -
Weight (Kg) Short Pattern BW 60 75 80 120 270 1100
Weight (Kg) Long Pattern BW 70 120 90 150 320 1225 1325 1900 2130 2860
Weight (Kg) Long Pattern RF 90 140 100 170 480 1346 1400 2200 2650 3300
Note 900LB 2” & 21⁄2” are the same as 1500LB 2” & 21⁄2”Parabolic disc for low torqueFor 1⁄2” to 11⁄2” dimensions see detailed overview brochure.
*Stem is Based on B.S 1873
™®
page 32
A
B
C
Globe Valve(Pressure Seal Bonnet)Cat P189Class 1500
Full Port Design
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Bonnet Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Stem Stainless Steel A276 Gr.410 or A182 Gr. F6a/CR13
Hand Wheel Ductile Iron A536 Gr. 65-45-12
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Back Seat Ring Stainless Steel A276 Gr.410 or A182 Gr. F6a
Gland Flange Carbon Steel A105
Gland Ring Stainless Steel A182 Gr. F6a
Disc Gland Stainless Steel A217 Gr. CA-15
Yoke Bush Ductile Iron or Bronze A439 Gr. D2C or B62
Gland Bolt Carbon Steel A193 Gr. B7/B7M
Gland Nut Carbon Steel A194 Gr. 2H/2HM
Gland Bolt Pin Carbon Steel A108 Gr. 1020
Wheel Nut Stainless Steel A194 Gr. 8/A105
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Name Plate Stainless Steel 304/AL
Packing Asbestos Free Reinforced Graphite
Gasket Soft Metal Ring CAD Plated
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600*
Testing API 598
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12”
A. Face to Face RF/BW 368 419 470 546 785 832 991 1130
A. Face to Face RTJ 371 422 473 549 708 835 1000 1146
A. Short Pattern End to End BW 216 254 305 406 559 711
B. Valve Open 597 648 724 832 1019 1181 1600 1950
C. Hand Wheel Dia 406 457 559 610 813 813 - -
Weight (Kg) Short Pattern BW 60 64 80 105 229 411
Weight (Kg) Long Pattern BW 73 100 140 220 440 1190 1480 2300
Weight (Kg) Long Pattern RF 98 130 170 255 590 1290 1700 2600
Note 900LB 2” & 21⁄2” are the same as 1500LB 2” & 21⁄2”Parabolic disc for low torqueFor 1⁄2” to 11⁄2” dimensions see detailed overview brochure.
*Stem is Based on B.S 1873
™®
page 33
A
B
C
Swing Check ValveCat P147Class 150
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Cover Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Hinge Carbon Steel A276 Gr. 410 or A182 Gr. F6a/CR13
Hinge Pin Stainless Steel A182 Gr. F6a/CR13
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Plug Carbon Steel A108 Gr. 1045
Cover Bolt Carbon Steel A193 Gr. B7/B7M
Cover Nut Stainless Steel A194 Gr. 2H/2HM
Disc Nut Stainless Steel A563 Gr. B
Washer Stainless Steel A276 Gr. 410
Eye Bolt Carbon Steel A105
Name Plate Stainless Steel 304 AL
Gasket Spiral Wound 304/316 Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600*
Testing API 598
dIMENSIONS (MM)
dIMENSIONS (MM)
Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF 165 203 216 237 292 356 495 622 698 787 864
A. End to End BW 165 203 216 237 292 356 495 622 698 787 864
B. Valve Open 114 140 140 156 184 292 353 371 416 489 521
Weight (Kg) RF 11 15 23 33 44 78 137 207 279 428 555
Weight (Kg) BW 8.5 12 16 24 34 63 122 175 229 368 483
Size (in) 18” 20” 24” 28” 30”
A. Face to Face RF 978 978 1295 1448 1524
A. End to End BW 978 978 1295 1448 1524
B. Valve Open 559 590 702 710 870
Weight (Kg) RF 775 835 1300 1450 1620
Weight (Kg) BW 685 720 1150 1300 1450
For RTJ dimensions see detailed overview brochure.For 5” dimensions see page 44 and detailed overview brochure.For 1⁄2” to 1” dimensions see page 44 and detailed overview brochure..For CF8/CF8M 150Lb see page 44.
*Also meets design requirements for ANSI B16.34
Full Port Design
™®
page 34
A
B
Swing Check ValveCat P159Class 300
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Cover Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Hinge Carbon Steel A216 Gr WCB
Hinge Pin Stainless Steel A182 Gr. F6a/CR13
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Plug Carbon Steel A108 Gr.1045
Cover Bolt Carbon Steel A193 Gr. B7/B7M
Cover Nut Carbon Steel A194 Gr. 2H/2HM
Disc Nut Carbon Steel A563 Gr. B
Washer Stainless Steel A276 Type 410
Eye Bolt Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Gasket Spiral Wound 304/316 Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600
Testing API 598
dIMENSIONS (MM)
dIMENSIONS (MM)
Size (in) 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16”
A. Face to Face RF 241 267 292 317 356 444 533 622 711 838 864
A. End to End BW 241 267 292 317 356 444 533 622 711 838 864
B. Valve Open 140 149 165 184 209 305 368 410 457 514 565
Weight (Kg) RF 12 21 24 39 60 90 175 210 300 700 774
Weight (Kg) BW 10 15 17 30 50 68 145 180 260 490 640
Size (in) 18” 20” 24” 28” 30”
A. Face to Face RF 978 1016 1346 1499 1595
A. End to End BW 978 1016 1346 1499 1595
B. Valve Open 714 746 780 790 820
Weight (Kg) RF 1000 1273 1650 1725 1819
Weight (Kg) BW 850 1100 1400 1570 1700
For RTJ dimensions see detailed overview brochure.For 5” dimensions see page 44 and detailed overview brochure.For 1⁄2” to 1” dimensions see page 44 and detailed overview brochure.For CF8/CF8M 300Lb see page 44.
*Also meets design requirements for ANSI B16.34
Full Port Design
™®
page 35
A
B
Swing Check ValveCat P175Class 600
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Cover Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Hinge Carbon Steel A216 Gr WCB
Hinge Pin Stainless Steel A182 Gr. F6a/CR13
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Plug Carbon Steel A108 Gr.1045
Cover Bolt Carbon Steel A193 Gr. B7/B7M
Cover Nut Carbon Steel A194 Gr. 2H/2HM
Disc Nut Carbon Steel A563 Gr. B
Washer Stainless Steel A276 Type 410
Eye Bolt Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Gasket Metal Ring Joint or Spiral Wound SS Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600
Testing API 598
dIMENSIONS (MM)
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF 292 330 356 432 559 660 787 838 889 991 1092
A. Face to Face RTJ 295 333 359 435 562 664 791 841 8912 994 1095
A. End to End BW 292 330 356 432 559 660 787 838 991 991 1092
B. Valve Open 159 184 197 292 352 397 492 556 737 650 771
Weight (Kg) RF 28 38 55 87 207 354 580 790 892 1200 1600
Weight (Kg) BW 20 30 42 65 155 280 490 670 750 1020 1350
Size (in) 20” 24”
A. Face to Face RF 1194 1397
A. Face to Face RTJ 1200 1407
A. End to End BW 1194 1397
B. Valve Open 800 900
Weight (Kg) RF 2420 3150
Weight (Kg) BW 2050 2720
*Also meets design requirements for ANSI B16.34
Full Port Design
™®
page 36
A
B
Swing Check ValveCat P187Class 900
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Cover Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Hinge Carbon Steel A216 Gr WCB
Hinge Pin Stainless Steel A182 Gr. F6a/CR13
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Plug Carbon Steel A108 Gr.1045
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Disc Nut Carbon Steel A563 Gr. B
Washer Stainless Steel A276 Type 410
Eye Bolt Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Gasket Metal Ring Joint or Spiral Wound SS Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600
Testing API 598
*10” and over sizes are according to ANSI B16.34All sizes meet the design requirements for ANSI B16.34
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130 1219
A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140 1232
A. Face to Face Short Pattern BW 216 254 305 356 508 660 757 914 991 1092
B. Valve Height 340 371 302 333 413 495 571 535 686 757 819
Weight (Kg) Short Pattern BW 50 56 50 100 240 380 6000 840 1040 1410 2050
Weight (Kg) Long Pattern BW 73 100 82 154 290 535 772 1290 1390 1810 2400
Weight (Kg) Long Pattern RF 59 77 80 120 265 404 600 1100 1140 1510 2050
dIMENSIONS (MM)
Size (in) 20”
A. Face to Face RF/BW 1321
A. Face to Face RTJ 1334
B. Valve Height 867
Weight (Kg) Long Pattern BW 3100
Weight (Kg) Long Pattern RF 3500
Full Port Design
™®
page 37
A
B
Swing Check ValveCat P199Class 1500
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Cover Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Hinge Carbon Steel A216 Gr WCB
Hinge Pin Stainless Steel A182 Gr. F6a/CR13
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Plug Carbon Steel A108 Gr.1045
Bonnet Bolt Carbon Steel A193 Gr. B7/B7M
Bonnet Nut Carbon Steel A194 Gr. 2H/2HM
Disc Nut Carbon Steel A563 Gr. B
Washer Stainless Steel A276 Type 304
Eye Bolt Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Gasket Metal Ring Joint or Spiral Wound SS Graphite filled
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600
Testing API 598
*10” and over sizes are according to ANSI B16.34All sizes meet the design requirements for ANSI B16.34
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF/BW 368 419 470 546 705 832 991 1130 1257 1384 1537
A. Face to Face RTJ 371 422 473 549 711 841 1000 1146 1276 1407 1559
A. Short Pattern End to End BW 216 254 305 406 559 711 867 991 1067 1194 -
B. Valve Height 260 271 302 333 413 495 571 635 686 756 819
Weight (Kg) Short Pattern BW 58 78 89 180 400 610 990 1900 2000 3000 4200
Weight (Kg) Long Pattern RF 73 111 127 286 617 953 1460 2390
Weight (Kg) Long Pattern BW 69 87 95 185 490 815 1273 2070
dIMENSIONS (MM)
Size (in) 20”
A. Face to Face RF/BW 1664
A. Face to Face RTJ 1686
A. Short Pattern End to End BW -
B. Valve Height 2600
Weight (Kg) Short Pattern BW 4809
Full Port Design
™®
page 38
A
B
Swing Check Valve(Pressure Seal Bonnet)Cat P187Class 900
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Cover Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Hinge Carbon Steel A216 Gr WCB
Hinge Pin Stainless Steel A182 Gr. F6a/CR13
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Plug Carbon Steel A108 Gr.1045
Cover Bolt Carbon Steel A193 Gr. B7/B7M
Cover Nut Carbon Steel A194 Gr. 2H/2HM
Disc Nut Carbon Steel A563 Gr. B
Washer Stainless Steel A276 Type 304
Eye Bolt Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Gasket Soft Metal Ring CAD Plated
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600
Testing API 598
*10” and over sizes are according to ANSI B16.34All sizes meet the design requirements for ANSI B16.34
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF/BW 368 419 381 457 610 737 838 965 1029 1130 1219
A. Face to Face RTJ 371 422 384 460 613 740 841 968 1038 1140 1232
A. Short Pattern End to End BW 216 254 305 356 508 660 787 914 991 1092 -
B. Valve Height 260 271 302 333 413 495 571 535 686 757 819
Weight (Kg) Short Pattern BW 50 56 50 100 240 380 560 840 1040 1410 2050
Weight (Kg) Long Pattern BW 59 77 80 120 254 404 600 980 1140 1410 1950
Weight (Kg) Long Pattern RF 75 106 82 159 299 550 866 1300 1400 1800 2400
dIMENSIONS (MM)
Size (in) 20”
A. Face to Face RF/BW 1321
A. Short Pattern End to End BW -
B. Valve Height 867
Weight (Kg) BW 3103
Weight (Kg) Long Pattern RF 3500
Full Port Design
™®
page 39
A
B
Swing Check Valve(Pressure Seal Bonnet)Cat P199Class 1500
Description material Specs.
Body Carbon Steel A216 Gr. WCB
Cover Carbon Steel A216 Gr. WCB
Disc Facing Stainless Steel A182 Gr. F6a/CR13 or Stellite/HF
Hinge Carbon Steel A216 Gr WCB
Hinge Pin Stainless Steel A182 Gr. F6a/CR13
Seat Ring Stainless Steel A182 Gr. F6a/CR13/Stellite/HF
Plug Carbon Steel A108 Gr.1045
Cover Bolt Carbon Steel A193 Gr. B7/B7M
Cover Nut Carbon Steel A194 Gr. 2H/2HM
Disc Nut Carbon Steel A563 Gr. B
Washer Stainless Steel A276 Type 304
Eye Bolt Carbon Steel A307 Gr. B
Name Plate Stainless Steel 304/AL
Gasket Soft Metal Ring CAD Plated
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design* API 600
Testing API 598
*10” and over sizes are according to ANSI B16.34All sizes meet the design requirements for ANSI B16.34
dIMENSIONS (MM)
Size (in) 2” 21⁄2” 3” 4” 6” 8” 10” 12” 14” 16” 18”
A. Face to Face RF/BW 368 419 470 546 705 832 991 1130 1257 1384 1537
A. Face to Face RTJ 371 422 473 549 711 841 1000 1146 1276 1407 1559
A. Short Pattern End to End BW 216 254 305 406 559 711 867 991 1067 1194 -
B. Valve Height 260 271 302 333 413 495 571 635 686 756 819
Weight (Kg) Short Pattern BW 58 76 89 180 400 650 1090 1850 2000 3000 4200
Weight (Kg) Long Pattern BW 69 87 110 185 490 815 1473 2070
Weight (Kg) Long Pattern RF 82 112 140 234 582 915 1683 2390
dIMENSIONS (MM)
Size (in) 20”
A. Face to Face RF/BW 1664
A. Face to Face RTJ 1686
A. Short Pattern End to End BW -
B. Valve Height 2600
Weight (Kg) Short Pattern RF 4809
Full Port Design
™®
page 40
A
B
Stainless Steel Gate ValveCat P47Class 150
Features• Investment cast to 300NB (12”)• Self aligning gland flange• Larger sizes fitted with thrust bearings for ease of operation• Yoke sleeve made from AL-Bronze or Austenitic DI for corrosion & wear resistance.
Description material Specs.
Body Stainless Steel A351 Gr. CF8/CF8M
Bonnet Stainless Steel A351 Gr. CF8/CF8M
Disc Stainless Steel A351 Gr. CF8/CF8M
Stem Stainless Steel A182 Gr. F304/F316
Hand Wheel Malleable Iron A197
Yoke Sleeve Austenitic DI A439 Gr. D2C or NR Bronze
Gland Flange Stainless Steel A351 Gr. CF8/CF8M
Gland Ring Stainless Steel A182 Gr. F304/F316
Wheel Nut Stainless Steel A351 Gr. CF8/CF8M
Bonnet Bolt Stainless Steel A193 Gr. B8
Bonnet Nut Stainless Steel A194 Gr. 8
Gland Bolt Stainless Steel A193 Gr. B8
Gland Nut Stainless Steel A194 Gr. 8
Gland Bolt Pin Stainless Steel A182 Gr. F304
Bearing - Thrust Ball
Grease Nipple Bronze B62 Cr. Plating
Set Screw Stainless Steel A193 Gr. B8
Name Plate Stainless Steel A240 Type 304
Packing Asbestos Free PTFE/Graphite
Bonnet Gasket PTFE or Graphite Sheet or 316 + Graphite SPW
Seat Stainless Steel (Integral) A351 Gr. CF8/CF8M or ST #6
Back Seat Stainless Steel (Integral) A351 Gr. CF8/CF8M
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design ANSI B16.34, API 600/API603
Testing API 598
dIMENSIONS (MM)
Size (in) 1⁄2” 3⁄4” 1” 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10”
Size (mm) 15 20 25 40 50 65 80 100 150 200 250
A. Face to Face RF 108 117.5 127 165 178 190.5 203 229 267 292 330
A. End to End BW 114 117.5 127 165 216 241 282.5 305 403 419 457
B. Valve Open 178 200 210 250 300 356 406 583 660 813 991
C. Hand Wheel Dia 102 102 127 152 178 179 203 229 254 305 356
Weight (Kg) RF * 4.2 5.2 7.1 11.1 16.1 18.2 22.7 39.1 64.1 101.4 150.9
150 CLASS
*Weights are for API603. For API600 weights see Page 20. For Buttweld weights and RTJ dimensons seedetailed overview brochure.
dIMENSIONS (MM)
Size (in) 12” 14” 16” 18” 20” 24”
Size (mm) 300 350 400 450 500 600
A. Face to Face RF 356 381 406 432 457 508
A. End to End BW 502 571.5 609.6 660 711 813
B. Valve Open 1194 1346 1524 1651 1829 2184
C. Hand Wheel Dia 406 508 559 559 609.6 660
Weight (Kg) RF * 218.1 288.6 341 659 841 1105
150 CLASS
Full Port Design
™®
page 41
A
C
B
Stainless Steel Gate ValveCat P33Class 300
Description material Specs.
Body Stainless Steel A351 Gr. CF8/CF8M
Bonnet Stainless Steel A351 Gr. CF8/CF8M
Disc Stainless Steel A351 Gr. CF8/CF8M
Stem Stainless Steel A182 Gr. F304/F316
Hand Wheel Malleable Iron A197
Yoke Sleeve Austenitic DI A439 Gr. D2C or NR Bronze
Gland Flange Stainless Steel A351 Gr. CF8/CF8M
Gland Ring Stainless Steel A182 Gr. F304/F316
Wheel Nut Stainless Steel A351 Gr. CF8/CF8M
Bonnet Bolt Stainless Steel A193 Gr. B8
Bonnet Nut Stainless Steel A194 Gr. 8
Gland Bolt Stainless Steel A193 Gr. B8
Gland Nut Stainless Steel A194 Gr. 8
Gland Bolt Pin Stainless Steel A182 Gr. F304
Bearing - Thrust Ball
Grease Nipple Bronze B62 Cr. Plating
Set Screw Stainless Steel A193 Gr. B8
Name Plate Stainless Steel A240 Type 304
Packing Asbestos Free PTFE/Graphite
Bonnet Gasket PTFE or Graphite Sheet or 316 + Graphite SPW
Seat Stainless Steel (Integral) A351 Gr. CF8/CF8M or ST #6
Back Seat Stainless Steel (Integral) A351 Gr. CF8/CF8M
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design ANSI B16.34, API 600 or API603
Testing API 598
dIMENSIONS (MM)
Size (in) 10” 12” 14” 16” 18” 20” 24”
Size (mm) 250 300 350 400 450 500 600
A. Face to Face RF 457 502 762 838 914 991 1143
A. End to End BW 457 502 762 838 914 991 1143
B. Valve Open 1016 1219 1372 1549 1956 2184 2565
C. Hand Wheel Dia 457 508 559 559 609.6 609.6 762
Weight (Kg) RF * 284 409 614 773 1250 1364 2614
300 CLASS
dIMENSIONS (MM)
Size (in) 1⁄2” 3⁄4” 1” 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10”
Size (mm) 15 20 25 40 50 65 80 100 150 200 250
A. Face to Face RF 140 152 165 190 216 241 282.5 305 403 419 457
A. End to End BW 140 152 165 190 216 241 282.5 305 403 419 457
B. Valve Open 200 200 210 250 300 381 432 508 686 864 1016
C. Hand Wheel Dia 100 100 140 203 203 203 229 254 356 406 457
Weight (Kg) RF * 6.1 7.9 9.7 15 19.5 30 40.9 60 111 184.5 284
300 CLASS
*Weights are for API603. For API600 weights see Page 21. For Buttweld weights and RTJ dimensons seedetailed overview brochure.
Full Port Design
Features• Investment cast to 300NB (12”)• Self aligning gland flange• Larger sizes fitted with thrust bearings for ease of operation• Yoke sleeve made from AL-Bronze or Austenitic DI for corrosion & wear resistance.
™®
page 42
A
C
B
Stainless Steel Globe ValveCat P143/P151Class 150-300
Description material Specs.
Body Stainless Steel A351 Gr. CF8/CF8M
Bonnet Stainless Steel A351 Gr. CF8/CF8M
Disc Stainless Steel A351 Gr. CF8/CF8M
Stem Stainless Steel A182 Gr. F304/F316
Hand Wheel Malleable Iron A197
Gland Flange Stainless Steel A351 Gr. CF8/CF8M
Gland Ring Stainless Steel A182 Gr. F304/F316
Disc Gland Stainless Steel A351 Gr. CF8/CF8M
Yoke Bush Austentic DI A439 Gr. D2C or NR Bronze
Bonnet Bolt Stainless Steel A193 Gr. B8
Bonnet Nut Stainless Steel A194 Gr. 8
Gland Bolt Stainless Steel A193 Gr. B8
Gland Nut Stainless Steel A194 Gr. 8
Gland Bolt Pin Stainless Steel A182 Gr. F304
Wheel Nut Stainless Steel A194 Gr. 8
Name Plate Stainless Steel A240 Type 304
Packing Asbestos Free PTFE or Graphite
Bonnet Gasket PTFE or Graphite Sheet or 316 + Graphite SPW
Seat Stainless Steel (Integral) A351 Gr. CF8/CF8M or ST #6
Back Seat Stainless Steel (Integral) A351 Gr. CF8/CF8M
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design ANSI B16.34/BS1873/API603
Testing API 598
dIMENSIONS (MM)
Size (in) 1⁄2” 3⁄4” 1” 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12”
Size (mm) 15 20 25 40 50 65 80 100 150 200 250 300
A. Face to Face RF 108 117.5 127 165 178 190.5 203 229 267 292 330 356
A. End to End BW 114 117.5 127 165 216 241 282.5 305 403 419 457 502
B. Valve Open 178 200 210 250 300 356 406 583 660 813 991 1194
C. Hand Wheel Dia 102 102 127 152 178 179 203 229 254 305 356 406
Weight (Kg) RF * 4.2 5.2 7.1 11.1 16.1 18.2 22.7 39.1 64.1 101.4 150.9 218.1
dIMENSIONS (MM)
Size (in) 1⁄2” 3⁄4” 1” 11⁄2” 2” 21⁄2” 3” 4” 6” 8” 10” 12”
Size (mm) 15 20 25 40 50 65 80 100 150 200 250 300
A. Face to Face RF 140 152 165 190 216 241 282.5 305 403 419 457 502
A. End to End BW 140 152 165 190 216 241 282.5 305 403 419 457 502
B. Valve Open 200 200 210 250 300 381 432 508 686 864 1016 1219
C. Hand Wheel Dia 100 100 140 203 203 203 229 254 356 406 457 508
Weight (Kg) RF * 6.1 7.9 9.7 15 19.5 30 40.9 60 111 184.5 284 409
300 CLASS
150 CLASS
*Weights are for ANSI B16.34. For API600 weights see Page 27. For 14” to 16” dimensions see detailed overview brochure. For Buttweld weights and RTJ dimensions see detailed overview brochure.
Full Port Design
Features• Investment cast to 300NB (12”)• Self aligning gland flange• Larger sizes fitted with thrust bearings for ease of operation• Yoke sleeve made from AL-Bronze or Austenitic DI for corrosion & wear resistance.
™®
page 43
A
B
C
Stainless Steel Check ValveCat P147/P159Class 150-300
*For API600 weights see page 34, 35.For Buttweld dimensons and weights see detailed overview brochure. For RTJ dimensions see detailed overview brochure.For 16” to 30” see detailed overview brochure.
parts Name materials
Body ASTM A351 Gr. CF8/CF8M
Bonnet ASTM A351 Gr. CF8/CF8M
Disc ASTM A351 Gr. CF8/CF8M
Arm ASTM A276 Gr. CF8/CF8M
Hinge Pin ASTM A276 Gr. 304/316
Split Pin AISI 304/316
Disc Nut AISI 304/316
Disc Washer AISI 304/316
Bonnet Bolt / Nut ASTM A193 Gr. B7/A194 Gr. 8/B8M
Gasket Teflon or Graphite or 316/GRP SPW
Plug ASTM A276 Gr. 304/316
Plug Gasket Teflon
Eye Bolt* ASTM A193 B8
Seat (Integral) ASTM A351 Gr. CF8/CF8M or ST #6
* Larger sizes only
dIMENSIONS (MM)
Size (in) 10” 12” 14”
Size (mm) 250 300 350
A. Face to Face 622 698 787
B. Centre Top 318 357 420
Weight (Kg) RF* 190 260 400
dIMENSIONS (MM)
Size (in) 1⁄2” 3⁄4” 1” 11⁄4” 11⁄2” 2” 21⁄2” 3” 4” 5” 6” 8”
Size (mm) 15 20 25 32 40 50 65 80 100 125 150 200
A. Face to Face 152 178 203 229 241 267 292 318 356 400 444 533
B. Centre Top 76 78 83 89 16 129 143 164 177 217 249 312
Weight (Kg) RF* 7 8 10 10 11 18 21 35 50 70 80 160
300 CLASS
150 CLASS
dIMENSIONS (MM)
Size (in) 1⁄2” 3⁄4” 1” 11⁄4” 11⁄2” 2” 21⁄2” 3” 4” 5” 6” 8”
Size (mm) 15 20 25 32 40 50 65 80 100 125 150 200
A. Face to Face 108 117 127 140 165 203 216 241 292 330 356 495
B. Centre Top 73 75 80 86 111 123 134 148 158 192 223 283
Weight (Kg) RF* 6 7 8 8 10 13 20 30 40 60 70 120
150 CLASS
dIMENSIONS (MM)
Size (in) 10” 12” 14”
Size (mm) 250 300 350
A. Face to Face 622 711 838
B. Centre Top 359 394 474
Weight (Kg) RF* 200 270 660
300 CLASS
Full Port Design
Features• Investment cast to 300NB (12”)• Larger sizes fitted with thrust bearings• Wall thickness ANSI B16.34
Standards
Face to Face/End to End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design ANSI B16.34/BS186873/API603
Testing API 598
™®
page 44
A
B
By-Pass & Drains
Gate Valve
Globe Valve
Check Valve
ball Valve
Valve Size 2” - 4” 5” - 8” 10”-24”
Drain and By-Pass Size
1⁄2” 3⁄4” 1”
Valve Size 2” - 4” 5” - 8” 10”-24”
Drain and By-Pass Size
11⁄2” 13⁄4” 21⁄8”
™®
page 45
STANDARDS COMPLIANCE:Basic Design: API 600, ANSI B16.34, BS 5157Face to Face Dimension: ANSI B16.10End to End Dimension: ANSI B16.10Flanged Ends: ANSI 16.5B.W. Ends: ANSI B16.25Drilling to ANSI or AS/BS2129 Table D to RPressure/Temperature ratings to ANSI B16.5/BS 1560
For installation in applications such as industrial, mining and mechanicalservices. Suitable for super-heated steam, H.T.H.W steam condensate andwater.
This design consists of two discs, kept in contact with parallel body seats,using the line pressure and seating action to effect tight closure.
Temperature changes in the line are accommodated by the expanding discand do not affect the action of the valve. When being opened or closed,the discs slide across the seat faces, dislodging any foreign matter. Thevalve operating stem is outside screw rising through the handwheel.
These valves are suitable for full bore steam use, where a low pressuredrop across the valve is required. Also suitable for water, oil, gas, etc.
O.S. & Y. Rising Stem Full Port, Expanded ParallelSlide Gate Valve, Double Disc, Pressure Seal orBolted Bonnet, Welded-in or Threaded Seat Rings.Mechanically loaded seating for low and highpressure sealing.
Parallel slide dual loaded discs ensure superiorshut off and allow by-pass/bleed fitment (doubleblock and bleed requires soft seat inserts).
Pressure/temperature charts available on request.
Buttweld ends
(Spring loaded DoubleDisc Style)
™®™®
pReSSURe/ tempeRatURe WCB BODy
For superheated steam etc. consult chart. WC6 chrome-moly available body for high temperature applications.
Parallel Slide Gate ValveCat P316SClass 150-1500 (BS/AS Table D to T)
StaNDaRD mateRIaL SpeCIFICatIONS
Class Cat No.
Test Pressure to API598 (PSIG) Working Pressure
Shell(Hydro)
Seat(Hydro)
Seat(Air)
CWPWOG
Saturated Steam(at 260°C)*
150(BST D to F)
150-P316SXU-S 450 315 80 280 170
300(BST H to J)
300-P316SXU-S 1125 815 80 720 600
600(BST K to R)
600-P316SXU-S 2225 1628 80 1440 1200
900(BST S)
900-P316SXU-S 3350 2442 80 2190 1800
1500(BST T)
1500-P136SXU-S 5626 4078 80 3600 3000
Part Material
1 Body ASTM A216 Gr. WCB
2 Spreader ASTM A182 Gr. F6
3 Seat Ring ASTM A105 + HF
4 Parallel Disc ASTM A216 Gr. WCB + F6/HF
5 Stem ASTM A182 Gr. F6
6 Bolt ASTM A193 Gr. B7
7 Nut ASTM A194 Gr. 2H
8 Gasket Stainless Steel/Graphite
9 Bonnet ASTM A216 Gr. WCB
10 Back Seat ASTM A182 Gr. F6
11 Packing Braided Graphite
12 Packing Flexible Graphite
13 Gland ASTM A182 Gr. F6
14 Gland Flange ASTM A216 Gr. WCB
15 Eye-Bolt ASTM A193 Gr. B7
16 Nut ASTM A194 Gr. 2H
17 Stem Nut ASTM A439 Gr. D2
18 Retaining Nut ASTM A105
19 Handwheel ASTM A395
20 Handwheel Nut Steel
21 Pin ASTM A182 Gr. F6
22 Spring Inconel X750
22
4
™®
page 46
C
B
A
Parallel Slide Gate ValveCat P316SClass 150-1500 (BS/AS Table D to T)
SeatingCode
Body SeatSurface Part
No. 3
Double DiscSurface Part
No. 4
StemPart No. 5
Back Seat(Stuffing Box)Part No. 10
X F6 F6 F6 F6
U Stellite Stellite F6 F6
XU Stellite F6 F6 F6
P* F304 F304 F304 F304
R* F316 F316 F316 F316
M* Monel Monel Monel Monel
N* Alloy 20 Alloy 20 Alloy 20 Alloy 20
H* Hastelloy B Hastelloy B Hastelloy B Hastelloy B
tRIm mateRIaL CODeS (tO apI 600)
Body Material Codes
None A216 WCB
0 Special
5 A217 C5
6 A217 WC6
8 A351 CF8
8M A351 CF8M
9 A217 WC9
VALVE SIZE(NPS)
inch 2 21⁄2 3 4 5 6 8 10 12 14 16 18 20 24
mm 50 65 80 100 125 150 200 250 300 350 400 450 500 600
CLASS150
(BST D to F)
D mm 51 64 76 102 125 152 203 254 305 337 387 438 489 591
A mm 178 190 203 229 254 267 292 330 356 381 406 432 457 508
B (Open) mm 409 472 490 612 720 806 990 1186 1415 1583 1771 1955 2210 2698
C mm 200 200 250 250 350 350 350 450 500 560 640 720 800 900
Weight (kg) RF 20 25 38 55 75 85 134 198 320 400 524 690 900 1350
CLASS300
(BST F to J)
D mm 51 64 76 102 125 152 203 254 305 337 387 438 489 591
A-A1 mm 216 241 283 305 354 403 419 457 502 760 838 914 991 1143
B (Open) mm 428 477 543 650 720 850 1037 1276 1438 1585 1960 2155 2350 2720
C mm 200 250 250 300 300 350 450 500 560 640 720 800 900 1118
Weight (kg) RF 25 44 50 74 124 137 217 337 580 715 1050 1235 1655 2320
CLASS600
(BST J to R)
D mm 51 64 76 102 125 152 203 254 305 337 387 438 489
A-A1 mm 292 330 356 432 508 559 660 787 838 889 991 1092 1192
B (Open) mm 474 553 593 654 857 970 1122 1330 1519 1716 2110 2400 2461
C mm 250 250 300 350 400 500 560 720 720 720 900 1000 1000
Weight (kg) RF 50 60 85 135 260 345 515 845 1120 1360 1910 2335 2700
CLASS900
(BST S to T)
D mm 51 60 76 102 120 152 203 254 305 324 375 438
A-A1 mm 372 419 384 460 559 613 740 841 968 1039 1140 1219
B (Open) mm 590 702 740 870 1051 1078 1318 1581 1867 2004 2178 2526
C mm 250 300 300 350 450 560 640 800 800 900 900 900
Weight (kg) RF 110 140 150 220 355 460 800 1050 1600 2220 3000 3870
OVeRaLL DImeNSIONS (mm) & WeIgHt (kg)
* Add XU modifier to end of model suffix if stellite seat, if stellite seat & disc add Umodifier to end.
Note: 15mm to 40mm NB also available refer to individual drawings.
™®
page 47
pReSSURe/ tempeRatURe WCB BODy
™®™®
Parallel Slide Gate ValveCat P316HClass 150-1500 (BS/AS Table D to T)
The P316H style parallel slide is the same dimensions as the P316S except haspillar type top works. The P316H also has spring energised discs.
For installation in applications such as industrial, mining and mechanical services. Suitable for super-heated steam, H.T.H.W steam condensate andwater.
This design consists of two discs, kept in contact with parallel body seats, usingthe tension spring to effect tight closure.
Temperature changes in the line are accommodated by the energised discs anddo not affect the action of the valve. When being opened or closed, the discsslide across the seat faces, dislodging any foreign matter. The valve operatingstem is outside screw rising through the handwheel (OSY).
These valves are suitable for full bore steam use, where a low pressure dropacross the valve is required. Also suitable for water, oil, gas, etc.
STANDARDS COMPLIANCE:Basic Design: API 600/BS EN 1984/S 5157/ANSI B16.34Face to Face Dimension: ANSI B16.10End to End Dimension: ANSI B16.10Flanged Ends: ANSI 16.5B.W. Ends: ANSI B16.25Drilling to ANSI or BS/AS2129 Table D to RPressure/Temperature Ratings to ANSI B16.34/BS 1560
O.S. & Y. Rising Stem, Full Port, Expanded ParallelSlide Gate Valve, Double Spring energised Discs,Pressure Seal or Bolted Bonnet, Welded-in or ThreadedSeat Rings. Spring energised loaded seating for lowand high pressure sealing.
Parallel slide dual loaded discs ensure superior shut offand allow by pass/bleed fitment (double block andbleed requires soft seat inserts).
Buttweld ends
StaNDaRD mateRIaL SpeCIFICatIONS
3/4
C
B
A
D R P O
For superheated steam etc. consult chart. * WC6 chrome-moly available body for high temperature applications.
Class Cat No.
Test Pressure to API598 (PSIG) Working Pressure
Shell(Hydro)
Seat(Hydro)
Seat(Air)
CWPWOG
Saturated Steam(at 260°C)*
150(BST D to F)
150-P316HXU-S 450 315 80 280 170
300(BST H to J)
300-P316HXU-S 1125 815 80 720 600
600(BST K to R)
600-P316HXU-S 2225 1628 80 1440 1200
900(BST S)
900-P316HXU-S 3350 2442 80 2190 1800
1500(BST T)
1500-P136HXU-S 5626 4078 80 3600 3000
Z-d
C 1.6
™®
page 48
part material
1 Body ASTM A216 Gr. WCB2 Seat Ring ASTM A105 + HF3 Spring Inconel X 7504 Spring Coil AISI 4105 Parallel Disc ASTM A216 Gr. WCB + F6/HF6 Bushing AISI 4107 Pin AISI 4108 Stem ASTM A182 Gr. F69 Gasket Stainless Steel/Graphite10 Bolt ASTM A193 Gr. B711 Nut ASTM A194 Gr. 2H12 Back Seat Ring ASTM A182 Gr. F613 Packing Flexible Graphite14 Packing Braided Graphite15 Gland ASTM A182 Gr. F616 Gland Flange ASTM A216 Gr. WCB17 Bolt ASTM A193 Gr. B718 Nut ASTM A194 Gr. 2H19 Bonnet ASTM A216 Gr. WCB20 Bolt ASTM A194 Gr. 2H21 Supporting Pole 104522 Guide Pole 104523 Yoke Plate 102524 Bolt ASTM A194 Gr. 2H25 Supporting Disc 102526 Stem Nut D-227 Retaining Nut 103528 Handwheel A4729 Handwheel Nut 1035
OVeRaLL DImeNSIONS (mm) & WeIgHt (kg)
Parallel Slide Gate ValveCat P316HClass 150-1500 (BS/AS Table D to T)
Note:- 15NB to 40NB also available. Refer to drawings
SeatingCode
Body SeatSurface Part
No. 2
Double DiscSurface Part
No. 5
StemPart No. 8
Back Seat(Stuffing Box)Part No. 12
X F6 F6 F6 F6
U Stellite Stellite F6 F6
XU Stellite F6 F6 F6
P* F304 F304 F304 F304
R* F316 F316 F316 F316
M* Monel Monel Monel Monel
N* Alloy 20 Alloy 20 Alloy 20 Alloy 20
H* Hastelloy B Hastelloy B Hastelloy B Hastelloy B
tRIm mateRIaL CODeS (tO apI 600)
* Add XU modifier to end of model suffix if stellite seat, if stellite seat & disc add U
modifier to end.
VALVE SIZE(NPS)
inch 2 21⁄2 3 4 5 6 8 10 12 14 16 18 20 24
mm 50 65 80 100 125 150 200 250 300 350 400 450 500 600
CLASS150
(BST D to F)
D mm 51 64 76 102 125 152 203 254 305 337 387 438 489 591
A mm 178 190 203 229 254 267 292 330 356 381 406 432 457 508
B (Open) mm 409 472 490 612 720 806 990 1186 1415 1583 1771 1955 2210 2698
C mm 200 200 250 250 350 350 350 450 500 560 640 720 800 900
Weight (kg) RF 20 25 38 55 75 85 134 198 320 400 524 690 900 1350
CLASS300
(BST F to J)
D mm 51 64 76 102 125 152 203 254 305 337 387 438 489 591
A-A1 mm 216 241 283 305 381 403 419 457 502 760 838 914 991 1143
B (Open) mm 428 477 543 650 720 850 1037 1276 1438 1585 1960 2155 2350 2720
C mm 200 250 250 300 300 350 450 500 560 640 720 800 900 1118
Weight (kg) RF 25 44 50 74 124 137 217 337 580 715 1050 1235 1655 2320
CLASS600
(BST J to R)
D mm 51 64 76 102 125 152 203 254 305 337 387 438 489
A-A1 mm 292 330 356 432 508 559 660 787 838 889 991 1092 1192
B (Open) mm 474 553 593 654 857 970 1122 1330 1519 1716 2110 2400 2461
C mm 250 250 300 350 400 500 560 720 720 720 900 1000 1000
Weight (kg) RF 50 60 85 135 260 345 515 845 1120 1360 1910 2335 2700
CLASS900
(BST S to T)
D mm 51 60 76 102 120 152 203 254 305 324 375 438
A-A1 mm 372 419 384 460 559 613 740 841 968 1039 1140 1219
B (Open) mm 590 702 740 870 1051 1078 1318 1581 1867 2004 2178 2526
C mm 250 300 300 350 450 560 640 800 800 900 900 900
Weight (kg) RF 110 140 150 220 355 460 800 1050 1600 2220 3000 3870
™®
page 49
Body Material Codes
None A216 WCB
0 Special
5 A217 C5
6 A217 WC6
8 A351 CF8
8M A351 CF8M
9 A217 WC9
p143XU-D 150 CLaSS (to BSt-F)280 PSI CWP (WOG)170 PSI Saturated Steam (at 260ºC)
p151XU-D 300 CLaSS (to BSt-J)
720 PSI CWP (WOG)600 PSI Saturated Steam (at 260ºC)For superheated steam consult pressure/temp chart
p171XU-D 600 CLaSS (to BSt-R)1440 PSI CWP (WOG) 1100 psi at 260°C, 825 psi at 400°C. For other temperatures consult chart.
Screw Down Non Return“Stop Check” Globe ValveCat P143-D/P151-D/P171-DClass 150-600 (BS/AS Table D to R)
For horizontal installations in applications such as industrial, miningand mechanical services. Suitable for super-heated steam, H.T.H.W.,steam, condensate and water.
FEATURES:Screw-Down Non-Return Globe ValveGuided loose disc for combination checkand stop.Bolted Bonnet, O.S. & Y., Swivel Disc .25% maximum carbon content on WCB.
STANDARDS COMPLIANCE:Basic Design: API 600/AS1873 and ANSIB16.34Face to Face Dimension: ANSI B16.10End to End Dimension: ANSI B16.10Flanged Ends: ANSI 16.5B.W. Ends: ANSI B16.25Drilling to ANSI or BS/AS2129 Table D to RPressure/Temperature Ratings to ANSIB16.34.
* Fitted on larger sizes & higher classes. Other Body and Trim materials available such as WC6, bronze, etc. See detailed overview brochure.
Buttweld ends
WORKINg pReSSURe
Overall Dimensions (mm & in) & Weight (kg)
StaNDaRD mateRIaL SpeCIFICatIONS
™®™®
*Available in undrilled to accommodate BS table drilling. ANSI flanges can also be machined to BStable thickness to allow face to face dimension alteration. 1⁄2” to 11⁄2” see page 48.
Part Name Materials
1 Body ASTM A216 Gr. WCB*
2 Seat Ring ASTM A105 with HF overlay
3 Disc ASTM A105 with F6 overlay
4 Stem ASTM A182 Gr. F6
5 Gasket Spiral Wound 316/GRP
6 Gasket Ring Joint CAD Plated
7 Bonnet ASTM A216 Gr. WCB (or WC6)
8 Bonnet Bolt ASTM A193 Gr. B7
9 Bonnet Nut ASTM A194 Gr. 2H
10 Back Seat Bushing ASTM A182 Gr. F6
11 Stem Packing Braided graphite (top & Bottom)
12 Stem Packing Flexible graphite
13 Lantern Ring*1 ASTM A182 Gr. F6
14 Pin ASTM A182 Gr. F6
15 Gland ASTM A182 Gr. F6
16 Gland Flange ASTM A216 Gr. WCB
17 Gland Bolt ASTM A193 Gr. B7
18 Gland Nut ASTM A194 Gr. 2H
19 Yoke Bush Gr. D2C or Bronze B62
20 Handwheel A536/A197
21 Wheelnut ASTM A105
VALVE SIZE (NPS)
inch 2 21⁄2 3 4 5 6 8 10 12mm 50 65 80 100 125 150 200 250 300
CLASS 150*(BST D TO F)
A-A1
(RF-BW)inch 8 81⁄2 91⁄2 111⁄2 14 16 191⁄2 241⁄2 271⁄2mm 203 216 241 292 356 406 495 622 698.5
B (Open)inch 133⁄4 147⁄8 16 177⁄8 223⁄8 221⁄2 247⁄8 291⁄8 393⁄8mm 349 378 407 454 569 573 632 740 1000
Cinch 8 10 10 12 15 16 18 20 20mm 200 250 250 300 390 400 450 500 500
Weight(kg)
inch 22 31 37 58 103 111 179 240 410mm 19 25 26 50 95 101 159 215 370
CLASS 300*(BST F TO J)
A-A1
(RF-BW)inch 101⁄2 111⁄2 121⁄2 14 153⁄4 171⁄2 22 241⁄2 28mm 267 292 318 356 400 444.5 559 622 711
B (Open)inch 141⁄4 151⁄2 167⁄8 19 263⁄8 265⁄8 301⁄2 407⁄8 541⁄8mm 362 394 429 482 669 676 774 1040 1375
Cinch 8 10 12 14 16.9 18 20 20 20mm 200 250 300 350 430 450 500 500 500
Weight(kg)
inch 28 47 54 76 150 162 270 340 550mm 22 40 43 61 130 136 232 280 520
CLASS 600*(BST J TO R)
A-A1
(RF-BW)inch 111⁄2 13 14 17 22 26 31 33mm 292 330 356 432 559 660 787 838
A (RTJ)inch 115⁄8 131⁄8 141⁄8 171⁄8 221⁄8 261⁄8 311⁄8 331⁄8mm 295 333 359 435 562 664 791 841
B (Open)inch 191⁄2 211⁄8 231⁄4 281⁄8 385⁄8 443⁄4 503⁄32 582⁄3mm 495 537 590 714 981 1136 1276 1490
Cinch 10 12 14 16 22 24 24 267⁄8mm 250 300 350 400 550 600 600 680
Weight(kg)
inch 51 62 85 143 340 520 720 950mm 42 51 72 120 284 465 580 830
™®
page 50
C
B
A
Screw-Down Non-Return Globe Valve (combination globeand check valve), Bolted Bonnet, O.S. & Y., Swivel Disc(guided loose disc for combination check and stop). Orcan be supplied as standard globe stop valve. Drilling toANSI and table D to R AS/BS2129.
WORKING PRESSUREp143R 150 CLaSS (to BSt-F)
280 PSI CWP (WOG)170 PSI Saturated Steam (at 260ºC)p151R 300 CLaSS (to BSt-J)
720 PSI CWP (WOG)600 PSI Saturated Steam (at 260ºC)For superheated steam consult pressure/temp chartp171R 600 CLaSS (to BSt-R)
1440 PSI CWP (WOG) for high temperature, consult chart
WC6 body is available for high temperature applications.
Buttweld ends
™®™®
*On larger sizes and higher classes.Note: Other trim materials are available upon request, such as bronze.
For installations in application such as industrial, mining and mechanical services. Suitable for super-heated steam, H.T.H.W, steam, condensate and water.Stem is guided for smooth operation.Also available in Bronze, Iron, chrome-moly etc.
“Right Angle StyleScrew Down Non ReturnStop Check” Globe Valve
Cat P143-R/P151-R/P171-RClass 150-600 (BS/AS Table D to R)
No Part Material
1 Body ASTM A216 Gr. WCB or WC6
2 Seat Ring ASTM A105 with HF overlay
3 Disc ASTM A105 with F6 overlay
4 Stem ASTM A182 Gr. F6
5 Gasket S/S Spiral Wound Graphite filled
6 Bonnet ASTM A216 Gr. WCB or WC6
7 Bonnet Bolt ASTM A193 Gr. B7
8 Bonnet Nut ASTM A194 Gr. 2H
9 Back Seat Bushing ASTM A182 Gr. F6
10 Stem Packing Braided graphite (top & bottom)
11 Stem Packing Flexible graphite
12 Lantern Ring* ASTM A182 Gr. F6
13 Pin ASTM A182 Gr. F6
14 Gland ASTM A182 Gr. F6
15 Gland Flange ASTM A216 Gr. WCB or WC6
16 Gland Eyebolt ASTM A193 Gr. B7
17 Gland Nut ASTM A194 Gr. 2H
18 Stem Nut ASTM A439 Gr. D2
19 Handwheel ASTM A395
20 H.W. Lock Nut Steel
OVeRaLL DImeNSIONS (mm) & WeIgHt (kg)
VALVE SIZE(NPS)
inch 2 21⁄2 3 4 5 6 8 10 12
mm 50 65 80 100 125 150 200 250 300
CLASS 150
(BST D TO F)
L* (RF-BW) mm 102 ⁄114 146 ⁄108 121 ⁄159 152 ⁄165 178 203 ⁄216 241 ⁄248 305 ⁄311 305 ⁄349
B (Open) mm 373 390 420 500 550 565 670 770 880
C mm 200 250 250 300 390 390 450 550 600
O mm 152 178 191 229 254 279 343 406 483
Weight (kg)RF 22 31 377 58 103 111 179 240
BW 19 25 26 50 95 101 159 215 35
CLASS300
(BST F TO J)
L* (RF-BW) mm 133 117 ⁄127 140 ⁄159 146 ⁄178 178 ⁄191 222 279 311 349 ⁄355
B (Open) mm 390 425 485 580 700 770 900 1020 700
C mm 200 250 300 350 430 450 500 600 600
O mm 165 191 210 254 279 318 381 445 520
Weight (kg)RF 28 47 54 76 150 162 270
BW 22 40 43 61 130 136 232 394
CLASS600
(BST J TO R)
L* (RF-BW) mm 146 165 178 216 279 330 1450 419
B (Open) mm 423 498 575 750 1030 1290 1300 1504
C mm 250 300 350 450 600 650 650 650
O mm 165 191 210 273 356 419 510 560
Weight (kg)RF 51 62 85 143 340 520
BW 42 51 72 120 284 465
StaNDaRD mateRIaL SpeCIFICatIONS
* Two patterns are available hence 2 dimensions have been shown.Up to 400NB also available.
STANDARDS COMPLIANCE:Basic Design: BS1873/ANSI B16.34Test: API Standard 598 Flanged Ends: ANSI B16.5B.W. Ends: ANSI B16.25Face to Face Dimension: BS2820 or ANSI B16.10Pressure/Temperature Ratings to ANSI B16.34.
™®
page 51
C
B
O
Od
L*
L*
Non Return - Lift TypeCat SLCLClass 150-600 (BS/AS Table D to R)
Non return valve, lift type, bolted bonnet, guided disc. Flangedrilling ANSI 150 to 600 and AS2129 table D to R.For horizontal installations in applications such as industrial,mining and mechanical services. Suitable for super-heatedsteam, H.T.H.W., steam, condensate and water.Guiding of stem assures smooth operation.Other body materials like Bronze and WC6 also available.
SLCL-SSpring Activated
SLCLXU-Z 150 CLaSS (to BSt-F)
280 PSI CWP (WOG)170 PSI Saturated Steam (at 260°C)SLCLXU-Z 300 CLaSS (to BSt-J)
720 PSI CWP (WOG)600 PSI Saturated Steam (at 260°C)For superheated steam consult pressure/temp chartSLCLXU-Z 600 CLaSS (to BSt-R)
1440 PSI CWP (WOG)1100 PSI at 260°C, 825 psi at 400°C. Consult chart for other temperaturesWC6 body is available for high temperature applications
*1 Spring Optional.*2 Drain Optional.
Buttweld ends
WORKING PRESSURE
OVeRaLL DImeNSIONS (mm & inches) & WeIgHt (kg)
StaNDaRD mateRIaL SpeCIFICatIONS
™®™®
VALVE SIZE (NPS)inch 2 21⁄2 3 4 5 6 8 10 12
mm 50 65 80 100 125 150 200 250 300
CLASS 150(BST D to F)
A-A1
(RF-BW)
inch 8 81⁄2 91⁄2 111⁄2 14 16 191⁄2 241⁄2 271⁄2
mm 203 216 241 292 356 406 495 622 698.5
Binch 67⁄8 7 71⁄2 85⁄8 91⁄4 123⁄4 151⁄8 175⁄8 211⁄4
mm 175 178 191 219 235 324 384 448 540
Weight(kg)
inch 20 24 35 55 84 96 160 245 345
mm 14 17 26 37 52 80 133 213 294
CLASS 300(BST F to J)
A-A1
(RF-BW)
inch 101⁄2 111⁄2 121⁄2 14 153⁄4 171⁄2 21 241⁄2 28
mm 267 292 318 356 400 444 533 622 711
Binch 73⁄4 8 83⁄4 107⁄8 115⁄8 131⁄4 161⁄4 181⁄4 221⁄8
mm 197 203 222 276 295 337 413 464 562
Weight(kg)
inch 35 37 60 82 110 155 268 380 495
mm 32 35 50 65 70 128 230 270 460
CLASS 600(BST J to R)
A-A1
(RF-BW)
inch 111⁄2 13 14 17 20 22 26 31 33
mm 292 330 356 432 508 559 660 787 838
Binch 81⁄4 85⁄8 101⁄2 113⁄4 131⁄4 15 183⁄4 215⁄8 225⁄8
mm 210 219 267 299 337 381 476 549 670
Weight(kg)
inch 40 55 72 120 175 270 420 620 810
mm 31 45 60 85 125 225 365 500 715
Part Name Materials
1 Body ASTM A216 Gr. WCB
2 Seat Ring ASTM A105 with HF overlay
3/4 Disc/Stem ASTM A105 with F6 overlay
5 Gasket Stainless Steel/Graphite
6 Bonnet ASTM A216 Gr. WCB
7 Bonnet Nut ASTM A194 Gr. 2H
8 Bonnet Bolt ASTM A193 Gr. B7
9*1 Spring Inconel X750
10 Gasket Graphite
11*2 Drain Plug A105N
STANDARDS COMPLIANCE:Basic Design: API 600/BS1873 and ANSI B16.34Face to Face Dimension: ANSI B16.10End to End Dimension: ANSI B16.10Flanged Ends: ANSI 16.5B.W. Ends: ANSI B16.25Drilling to ANSI or BS/AS2129 Table D to R
™®
page 52
A
B
Check Cast Iron BodyANSI Class 125-250 • SL404-SL404F
MATERIAL LIST
* Ductile Iron Body for 250 Class/and PN16 in larger sizes.*2 Bronze or stainless trim
dIMENSIONS & WEIGhTS
ASA125 cold working pressure:-200 PSI to 300NB, 150 PSI 350NB to 600NB.PN16 also available 1600 kpa C.W.P (232 PSI)ANSI 250 Class available to 12 inch (whichcan be drilled BS Table F)(Ductile Iron Body)
Swing checkConforming to MSS SP-71End Flange Dimensions: ANSI B16.5 or PN16/BS/ASFace to Face Dimensions: ANSI B16.10, BS5153, MSS-SP71Maximum temperature 210 ºCDrilled to suit ANSI Class 125 or PN10, PN16, JIS and AS/BS2129Table D to F. ANSI 250 Class and PN16 also available up to 300NB
™®
Part Name Material
1 Cover Bolt & Nut Steel
2 Cover* ASTM A126 Class B
3 Gasket Graphite
4 Hanger Pin Stainless Steel or F6
5 Hanger ASTM A126 Class B
6 Disc Ring ASTM B62 or F6
7 Disc ASTM A126 Class B
8 Disc Washer Steel
9 Disc Bolt Steel
10 Seat Ring*2 ASTM B62 or F6
11 Body* ASTM A126 Class B
Class Size (in) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24”
125
A 203 216 241 292 330 356 495 622 699 787 864 978 978 1295
A1 508
B 131 146 157 182 330 237 278 313 353 434 470 535 570 679
Weight 11 15 20 34 47 58 104 252 313 396 560 725 881 1276
250
A 267 292 318 356 445 533
A1 133 152 159 184 229 279
Weight 21 29 41 60 114 186
MM & kG
1
2
3
4
5
6
7
8
9
10
11 A/A1
B
™®
page 53
Gate Cast Iron BodyANSI Class 125/250/PN16 • SL600 - SL600F
™®1000 Kpa rated SL600-10
1600 Kpa rated SL600-16
Drilled to suit class 125 or AS/BS2129 Table C to F, PN10, PN16, JIS.Inside screw & yoke, solid wedge disc, bolted bonnet, non rising stemConforming to MSS SP-70/BS5150/5163End Flange Dimensions: ANSI B16.5/PN16/BS/ASFace to Face: ANSI B16.10, BS5150/BS5163/MSS-SP70 (PN16)Ductile Iron Body for ANSI 150 Class and PN16 in larger sizes.
MATERIAL LIST
NOTE: *Bronze B16 or stainless steel CR13/304/316 on request.Maximum temperature 210°C
NOTE: NPS above 600NB (24") can be furnished on request
dIMENSIONS & WEIGhTS MM & kG
Part Name Material
1 Body ASTM A126 Class B
2 Seat Ring ASTM B62 (bronze*)
3 Wedge Face Ring ASTM B62 (bronze*)
4 Wedge ASTM A126 Class B
5 Stem* Bronze/Brass/F6
6 Body Gasket Graphite
7 Bolt Steel B7
8 Nut Steel 2H
9 Bonnet ASTM A126 Class B
10 Back Seat Bushing Cast Brass
11 Packing Graphite
12 Packing Gland Cast Brass/410SS
13 Packing Gland Bolt Alloy Steel B7
14 Gland Flange Nut Alloy Steel 2H
15 Gland Flange Cast Brass/410SS
16 Yoke Bushing Nut ASTM A126 Class B
17 Handwheel ASTM A126 Class B
18 Identification Plate Aluminium
19 Handwheel Nut Ductile Iron
Class Size(mm) 50 65 80 100 125 150 200 250 300 350 375 400 450 500 600 700 750
(in) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 15” 16” 18” 20” 24” 28” 30”
125
A (mm) 178 191 203 229 254 267 292 330 356 381/441 406/476 406/476 432/505 457/510 508/575 610
B (mm) 313 334 370 430 454 550 678 750 880 940 950 1080 1180 1380 1480 1670
C (mm) 203 203 203 254 254 305 356 406 457 508 560 559 610 610 762 910
Weight 15 21 26 44 61 74 127 216 283 375 638 550 600 840 1170
250
A (mm) 216 241 282 305 403 419 457 502
B (mm) 315 340 390 440 460 560 678 798 895
C (mm) 203 229 254 305 406 508 559 610
Weight 23 41 54 84 166 272 418 636
Z-ød
ASA125: 200 PSI max cold working pressure 50NB to 300NB, 150 PSI350NB to 600NB, PN16 (232 PSI) also available.ANSI 150 rating also available in ductile iron body
C
B
A
™®
page 54
Gate Cast Iron BodyANSI Class 125-250 • SL601 - SL601F
NOTE: Special face to face dimensions also available.
dIMENSION & WEIGhTS MM & kG
MATERIAL LIST
™®
Part Name Material
1 Body ASTM A126 Class B*1
2 Seat Ring ASTM B62 or F6*2
3 Wedge Face Ring ASTM B62 or F6*2
4 Wedge ASTM A126 Class B
5 Stem Bronze/410SS
6 Body Gasket Graphite
7 Bolt Steel
8 Nut Steel
9 Bonnet ASTM A126 Class B
10 Back Seat Bushing Cast Brass/410SS
11 Packing Graphite
12 Packing Gland Cast Brass/410SS
13 Packing Gland Bolt Steel
14 Gland Flange Nut Steel
15 Yoke Bushing Ductile Iron
16 Gland Flange Cast Brass/410SS
17 Yoke Bushing Nut ASTM A126 Class B
18 Screw Steel
19 Handwheel*3 ASTM A126 Class B
20 Identification Plate Aluminium
21 Handwheel Nut Ductile Iron or B62
Class Size (in) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24”
125
A 178 191 203 229 254 267 292 330 356 381 406 432 457 508
B 375 408 441 545 656 770 959 1260 1486 1689 1860 2106 2295 2768
C 203 203 203 254 254 305 356 406 457 508 559 610 610 762
Weight 15 21 26 44 61 74 127 216 315 409 640 726 782 1353
250
A 216 241 282 205 403 419 457 502
B 368 445 521 629 876 1092 1340 1524
C 203 229 254 305 406 508 559 610
Weight 23 41 54 84 166 272 418 636
ANSI Class 125 or AS/BS2129 Table C to F as well as PN10,PN16, JIS etc. Also 250 Class & PN16 available up to 300NBOutside screw & Yoke, solid wedge disc, bolted bonnet.Conforming to MSS SP-70/BS5163/MSS-SP70End Flange Dimensions: ANSI B16.5/PN16/AS/BSFace to Face: ANSI B16.10/BS5150/BS5163/MSS-SP70210°C Maximum TemperatureANSI 150 & PN16 rating also available in Ductile Iron Body
*1 250 Class is Ductile Iron Body.
*2 Available in 304, 316, 410, Bronze or Brass trim
*3 For Gear Operated version refer to drawing.
ASA 125: 200 PSI max cold working pressure 50NB to 300NB, 150 PSI 350Nbto 600Nb, PN16 (232 PSI) also available.150 and 250 Class also available to 300NB (12 inch) Ductile Iron Body.
C
B
A
™®
page 55
Globe Cast Iron BodyANSI Class 125-250 • SL201 - SL201F
MATERIAL LIST
* 150 & 250 Class in Ductile Iron Body.Bronze or stainless steel stem on request.Maximum temperature 210oC
ASA 125: 150 PSI max cold working pressure 350NB to 600NB, 200 PSI 50NB to 300NB. PN16 (232PSI) also available.150 Class also available to 12 inch.
™®
dIMENSION & WEIGhTS MM & kG
Class Size (in) 2” 2.5” 3” 4” 5” 6” 8” 10” 12” 14” 16” 18” 20” 24”
125
A 203 216 241 292 330 356 495 622 699 787 864 978 978 1295
B 335 356 392 446 489 516 663 832 1270 1430 1430
C 203 203 229 254 305 305 406 508 600 600 600
Weight 23 27 34 54 71 95 180 325 340 396 560 725 881 1276
250
A 267 292 318 356 445 533
B 349 375 419 470 591 724
C 229 254 254 305 406 508
Weight 28 37 54 73 145 259
Part Name Material
1 Body ASTM A126 Class B
2 Seat Ring ASTM B62 or F6
3 Disc ASTM A126 Class B
4 Disc Stem Ring ASTM B62 or F6
5 Back Seat Bushing Cast Brass or F6
6 Body Gasket Graphite
7 Nut Steel
8 Bolt Steel
9 Packing Graphite
10 Packing Gland Cast Brass or F6
11 Gland Flange Ductile Iron
12 Bonnet ASTM A126 Class B
13 Yoke Bushing Cast Brass or F6
14 Stem ASTM B16 or F6A
15 Handwheel ASTM B126 Class B
16 Handwheel Nut Ductile Iron
Class 125 cold working pressure:- 200 PSI to 200NB, 150 PSI200NB to 400NB (PN16-232 PSI also available). ANSI 150 and250 Class also available to 300NB in Ductile Iron Body
Conforming to MSS SP-85/BS5152End Flange Dimensions: ANSI B16.1/PN16Face to Face: ANSI B16.10/MSS-SP85/BS5152Drilled to suit ANSI 125 (ASA150) and BS table D to F, PN10,PN16 etc
C
B
A
™®
page 56
Australian Pipeline Valve don’t consider in our design the following factors of risk:
1. Australian Pipeline Valve “Standard” valves can be used in a temperature range between -29/+490°C. (Note, pressure limitations apply above 38°C refer to Pressure/Temperature charts.) For service temperatures below -29°C valves construction materials shall be submitted to an impact test at the minimum servicetemperature. For temperatures above and below the standard range, special seals need to be specified bythe client.
2. The onus is on the customer to specify all materials of construction and service conditions. Australian Pipeline Valve shall assume standard materials and conditions if not otherwise specified.
3. Australian Pipeline Valve “Standard” valves are not equipped with devices suitable to avoid internal over-pressures caused by incorrect operations of process or by fluids & liquids subjected to an increase of volume and/or pressure (these devices, such as the over pressure hole into the gate or safety seats are available upon request).
4. Australian Pipeline Valve “Standard” valves are not designed with special devices to withstand a sudden thermal jump (thermal shock).
5. In general Australian Pipeline Valve “Standard” valves are not mechanically designed to bear overloads due to exceptional atmospheric or natural phenomenon’s (such as earthquakes).
6. In general Australian Pipeline Valve “Standard” valves are not designed to bear loads on flanges, on pipe connections or pipe-line.
7. In general Australian Pipeline Valve “Standard” valves can’t withstand ice inside their bodies (in this case user has to consider the optional stem extension for insulating, avoiding the presence of residual product inside the valve).
8. Australian Pipeline Valve “Standard” valves are not suitable for low temperature service below - 46°C (-51°F) unless supplied (in suitable body material) with cryogenic stem extension and other modifications, (available on request).
9. Australian Pipeline Valve “Standard” valves are suitable for “industrial” oxygen (not medical) service when supplied degreased and packed in polyethylene bags only.
10. The compatibility between the valves construction materials and medium is selected by the user. The user is ultimately responsible for verifying the compatibility between medium and materials.
11. Abrasive or dirty service applications need to be considered and stated at time of order.
VALVE START-UP
Before installing the valve onto the pipe-line it is mandatory, for the user, to verify the compatibility of the valve with serv-ice conditions (medium, temperature and pressure). With reference to standard valves held in stock, the reseller and enduser will have to assure themselves of the compatibility between the valve and the conditions required by the customer.Australian Pipeline Valve gate valves must be only used for on-off (fully open/fully closed) service.
Before using the valve in a potential explosive atmosphere it’s necessary for the customer to: -
• To verify the correct type of valve and operator is specified.• To verify the compatibility between the valve and the zone in which the valve should be installed• To foresee the pipe-line ground condition on which the valve should be installed• To check that the temperature if the valve surface is not higher than the flammable point of the atmosphere
in which the valve is installed (in this case specify an insulating cover device for the valve and an extensionfor the operator)
• To avoid mechanical knocks during the installation that may cause sparks.
Australian Pipeline Valve cannot be held responsible for damage caused by use of the product for any reason, especiallyif it is improper use or modified.
CONSIDERATIONS OF TECHNICAL RISK / LIMIT OFLIABILITY FOR APV GATE, GLOBE, CHECK VALVES
™®
page 57
Local distributor
QUALITY
ASSURANCE
We are continually improving all facets of quality assurance. Full metalurgical and test certificates are always supplied for all pressure retaining parts, we also provide it on all majortrim components.
We have endeavoured to provide a broad outline of our range and capabilities. Because weare continually developing new products for our customers the brochure will, to some extent beincomplete. This catalogue is a general overview only, individual drawings and data sheets relevant to valve supplies can be furnished on request. Therefore if you have any requirementsin the field of valves please contact us for a prompt response. Continuous development ofAustralian Pipeline Valve products may necessitate changes in the design or manufacturingprocesses. Australian Pipeline Valve reserves the right to affect any such changes withoutprior notice.
CERTIFICATIONCERTIFICATION
™®