VAE-1-MC1 & VAE-1-MC2 - Midian Electronics & VAE-1-MC2 Voice Alarm Encoder with Lone Worker &...
Transcript of VAE-1-MC1 & VAE-1-MC2 - Midian Electronics & VAE-1-MC2 Voice Alarm Encoder with Lone Worker &...
1
VAE-1-MC1 & VAE-1-MC2
Voice Alarm Encoder with Lone Worker & Man-Down
Manual Revision: 2014-04-10 Covers Software Revisions: VS-1XXX: 01.70.1 or higher Covers MPS Version 4.80 & Higher This manual supports the following radios: VAE-1-MC1 North America: CM-300, PM-400 (4-key version), PR-400 (non-keypad version) EMEA Region: CM-160, CM-360, CP-140 Asia: GM-3688, GP-3688 (non-keypad version) Latin America: EM-400, EP-450 (non-keypad version) VAE-1-MC2
North America: PR-400 (full & limited keypad versions) EMEA Region: CP-160, CP-180 Asia: GP-3688 (full & limited keypad versions) Latin America: EP-450 (full & limited keypad versions)
2
HARDWARE SPECIFICATIONS Operating Voltage 4.75-8.2 VDC Operating Current Power Save Mode (COR Operation) 2.5 mA typical Power Save Mode (VOX Operation) 10 mA typical Normal Operation 17.5 mA typical Average w/COR Power Save (80-10-10 cycle) <5 mA Average w/COR Power Save (90-5-5 cycle) <4 mA Operating Temperature -30 - +60 C Frequency Response 300-3000 Hz Input Impedance >45 k Input Level (TX) 0.05-2.5 VPP Input Level (RX) 0.05-2.5 VPP Audio Output Impedance < 1200 Ohm
INSTALLATION OVERVIEW
1. Test the radio for functionality. 2. Program the radio per the Radio Programming Section of this manual. 3. Install the unit into the radio per the Hardware Installation Section of this manual. 4. Program the unit per the Product Programming Section of this manual. Note: Midian is not responsible for any damage/loss resulting from the use of Midian’s products.
3
GENERAL INFORMATION Midian’s VAE-1 is a voice alarm encoder that can have a voice message stored in it and when the emergency input is activated the VAE-1 will transmit an emergency ANI and/or the prerecorded voice message. The following are some common applications: Emergency Location and Lone Worker: The VAE-1 is ideal for providing voice location messages for Public Safety (firefighters and police) or for lone workers in areas where GPS location is not available. For example, firefighters can store a custom voice message into the VAE-1 as their location changes while fighting a fire in a building. If there is a fire in a ten story apartment building and the firefighter is working on the second floor in apartment 215, the firefighter can record “Second floor apartment 215”. If the firefighter moves to the third floor in apartment 306 the firefighter can rerecord the message to say “Third floor apartment 306”. If the emergency input is activated (by a button press, the lone-worker feature or Man-Down feature) then the VAE-1 will send an emergency ANI to identify to the dispatcher who is in trouble and then the voice message will follow to inform the dispatcher the distressed firefighter last recorded location. This enables the rescuers to concentrate their search efforts in one area of the apartment building rather than splitting their search efforts between ten stories. Locator tones can also be generated to provide an audible alert to the searchers. Emergency Alert: Public safety dispatchers do not want field radio users to talk on the channel without need when an emergency is occurring. The dispatcher can have the VAE-1 send a voice message such as “Emergency alert keep channel clear”. This message can be sent periodically until reset.
4
RADIO PROGRAMMING The following information is for programming the following Motorola radios: CP-140, EP-450, GP-3688, PR-400 It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using a RIB box and to hear confirmation beeps from the radio after programming the unit. 1. Upon starting the CPS programmer, click on View->Expert. 2. In the Option Board Window select “Advanced Option Interface” as the “Option Board Type”.
3. For each personality where option board functionality is desired, the Option Board box must be checked.
You may wish to enable the option board on some or all personalities. This depends on how the option board features will be controlled. This is explained in more detail in the Operation section.
5
CM-160, CM-300, EM-400, GM-3688, PM-400 It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using a RIB box and to hear confirmation beeps from the radio after programming the unit. 4. Upon starting the CPS programmer, click on View->Expert. 5. In the Option Board Window select “Advanced Option Interface” as the “Option Board Type”.
6. For each personality where option board functionality is desired, the Option Board box must be checked.
You may wish to enable the option board on some or all personalities. This depends on how the option board features will be controlled. This is explained in more detail in the next section.
6
The following step applies to the accessory connector and may be skipped by most users. 7. An accessory pin may be used to initiate an emergency ANI. This allows for an external emergency foot
switch or button, and frees-up one of the radio front buttons. To enable this feature, one of the radio accessory pins must be assigned to Option Board 2 (Input) via the CPS programmer. The switch must be held in the active state for about 2 seconds before an emergency ANI will be sent.
Note: Accessory pin features do not require any special module programming.
7
CM-360 Programming Instructions It is necessary to program the radio before installing the unit. This is because the Option Board Feature of the radio must be enabled in order to program the unit using a RIB box and to hear confirmation beeps from the radio after programming the unit. 1. Upon starting the CPS programmer, click on View->Expert. 2. In the Option Board Window select “Advanced” as the “Option Board Type”.
3. For each personality where option board functionality is desired, the Option Board box must be checked.
You may wish to enable the option board on some or all personalities. This will depend on how the option board features will be controlled. This is explained in more detail in the next section.
8
MC-1 PORTABLE HARDWARE INSTALLATION Be certain to follow standard anti-static procedures when handling any of Midian’s products. Radio Firmware: Before installing the unit, check the radio firmware version. This is determined by reading the radio using the CPS. The unit has been tested with radio firmware versions R02.00.01 and R03.00.01B. If the radio has an older version, it may need to be upgraded to ensure proper operation with the unit. Disassembling the Radio: Please consult Motorola’s Basic Service Manual for this radio for more detailed installation instructions.
1. Remove battery, knobs, and antenna.
2. Use chassis opener tool (Motorola P/N 6686533Z01) to open the radio. Insert the tool into the space between the case and the radio chassis at the bottom of the radio. Pull the tool downwards, separating the bottom of the chassis from the case. Make certain the rubber seal does not get damaged.
3. Unplug the speaker and microphone leads from the chassis as it is being removed from the front cover.
Installing the Option Board:
1. Motorola used to have the RLN5646A option board kit for installation into the non-keypad versions of this radio, but has discontinued this part. The option board kit consisted of the 28-pin flex cable and a metal shield. The 28-pin flex cable can be ordered from Midian as the COM Cable A or from Motorola as the 8415764H02. The shield from the keypad version of the radio can be used, but it must be modified per step 3. The shield is ordered as 4286648Z01 from Motorola. If using the 4286648Z01 it will be necessary to remove the 4 tabs that are circled in red in the picture below.
2. Connect the flex cable to the module and the main board of the radio.
9
3. Place the module into the front cover.
4. Install the shield by pressing down on the 4 side tabs. To have the shield fit into the front cover it is necessary to cut the shield at the red lines shown in the picture below.
If the RF shield is not available from Motorola then it will be necessary to shield the board using Kapton tape and copper tape. First insulate the component side of the board using the Kapton tape and then shield the component side of the baord using the copper tape. This will create a shield to keep RFI from getting into the board. Reassembling the Radio:
1. Reconnect the speaker and microphone. 2. Push the chassis up into the front cover and then push the bottom down until it snaps. Be careful not to
damage the rubber seal.
3. Replace the knobs, antenna and battery.
Option Board Side
Radio Side
10
MC-1 MOBILE HARDWARE INSTALLATION Be certain to follow standard anti-static procedures when handling any of Midian’s products. Radio Firmware: Before installing the option board, check the radio firmware version. This is determined by reading the radio using the CPS. The option board has been tested with radio firmware versions R03.00.03 and R03.00.04. If the radio has an older version, it may need to be upgraded to ensure proper operation with the option board. Disassembling the Radio: Please consult the booklet included with the option board installation kit COM Option B (Motorola P/N PMLN4623A) for illustrations and more detailed installation instructions. Equipment required: Small flat blade screwdriver (4 mm maximum). Torx style screwdriver, size T-10. Small Phillips screwdriver. 1. Disconnect power. 2. Use a flat blade screwdriver to pry the volume control knob away from the front cover. This is best done from
the bottom of the knob. Pull off the volume control knob. 3. Locate the two notches on the bottom which keep the control head in place. Use a flat blade screwdriver to
pry the control head away from the chassis. 4. Carefully separate the control head from the chassis and remove the flat cable connecting the two from the
chassis. 5. Use a flat blade screwdriver to pry the sides of the plastic cover away from the T-shaped mounting bosses on
the sides of the radio. 6. Use a flat blade screwdriver to pry the plastic cover away from the tab on the back of the radio. 7. Remove the plastic cover. 8. Insert a flat blade screwdriver into the gap between the main shield and chassis near the speaker cutout area
to lift the main shield from the chassis. Installing the Option Board:
1. The option board is installed in the radio using the COM Option B (Motorola P/N PMLN4623A). The COM Option B includes 4 metal stand-offs, 4 screws and a 28-pin flex cable.
2. Remove the 3 screws located in the option board area and replace the 3 screws with the 3 of the stand-
offs provided with the option board installation kit.
11
3. Connect the curved end of the flex cable to the option board making sure the silver contact pads face the option board.
4. Connect the other end of the flex cable to the option board connector in the radio, making sure the silver contact pads face the circuit board.
5. Place the option board on top of the spacers with the component side facing down.
6. Secure the board using the 3 screws provided in the installation kit.
Option Board Side
Radio Side
12
Reassembling the Radio:
1. Replace the main shield.
2. Replace the plastic cover.
3. Re-connect the control head cable to the chassis.
4. Replace the control head.
5. Replace the volume control knob.
13
MC-2 Hardware Installation Be certain to follow standard anti-static procedures when handling any of Midian’s products. Radio Firmware: Midian recommends installing the module into the radio with the existing firmware of the radio provided the firmware is at least R03.01.00. If the radio has a firmware version older than R03.01.00, it must be upgraded. If there are any issues with the firmware then the firmware should be upgraded to the latest. Verifying the firmware version can be done several ways. On most radios, this information is on a label on the back of the radio. For keypad & display radios, selecting the SoftwareVer# option from the utility menu will report the version. Consult Motorola if you cannot determine the firmware version. Disassembling the Radio: Additional disassembly instructions are also available in Motorola’s Basic Service Manual.
4. Remove the antenna, knobs, and battery.
5. With a Chassis Opener tool from Motorola or a 3/16” flat blade screwdriver, gently insert the tool into the space between the case and the radio chassis at the bottom of the radio. Gently pull the tool downwards, separating the bottom of the chassis from the case. Make certain the rubber seal does not get damaged.
6. Pull the bottom of the chassis downward until the knob switches are clear from the case. Flip the chassis
open so that the bottom of the case and the bottom of the chassis are end to end. Be careful when opening; as there are flex cables installed.
7. Lift the latches on the main board to release the 40-pin flex cable and the Speaker’s 20-pin flex cable
from their connectors.
8. Remove the RF shield in the front cover. This is done by inserting a flat blade screwdriver or a scribe behind the arm tab, pushing down, and then prying inwards. The tab should pop out. NOTE: Do not pry upwards from underneath the arm as damage could occur to the keypad electronics or the unit if already installed. After releasing all 4 arm tabs, gently lift the bottom of the RF shield and then pull downward to get the 2 top tabs clear of the case.
Installation:
1. For radios without a keypad and display, there may be a plastic piece in the front cover that should be removed, leave the rubber piece (if present) installed. For radios with a keypad and display, unlatch the flex connectors from the keypad electronics, remove the flex cables, and remove the keypad electronics.
2. Insert the 40-pin flex cable into the 40-pin flex connector on the unit, making certain it is seated properly,
then close the latch. Install the unit with the 40-pin connector towards the bottom facing up.
3. Reinstall the display flex and close the latch. Insert the other side of the 40-pin flex cable into the 40-pin flex connector on the radio’s main board. Reinstall the speaker flex and close the latch.
14
Reassembling the Radio: Additional assembly instructions are also available in Motorola’s Basic Service Manual.
1. Reinstall the RF shield over the Midian board, by first inserting the 2 top tabs and then snapping the 4 arm tabs back into place with a small flat blade screwdriver. Be certain the board is squarely aligned and not to damage the flex cables. The RF shield may bulge slightly in the center; this is normal.
2. Place the chassis into the front cover. Be certain the O-ring seal is properly aligned and does not get damaged. Push the chassis up into the case and then push the bottom down until it snaps.
3. Replace the knobs, antenna and battery.
15
PRODUCT PROGRAMMING Install the MPS software if you have not done so already. The modules are programmed through the radio using the radio programming cable and Midian’s MPS software. Start the MPS software. From the product selection screen on the MPS software, locate and select the desired VAE-1 model with the suffix MPP1/MPM1 or MC1 and click OK. Configure the programming software by selecting File->Preferences and make certain there is a check mark next to ‘Rib Box Enable’ by clicking on it. Also select the appropriate COM port. Set the parameters of the software to fit the application. If any clarifications on a feature are required, move the mouse cursor over the feature name until the question mark appears and right click, an on-line help for that feature will be shown. The MPS always defaults to “MDC Portable” as the radio type. On the basic settings tab it is necessary to select the proper radio type. After entering the parameters, save the file by going to File - Save As. Enter the file name in the File Name block and click Save. Saving the file will allow for quick and easy reprogramming of units. Turn power on to the radio and then the RIB. Click ProgramUnit! in the MPS software. You will hear 1-3 beeps from the radio if programmed successfully. To read the parameters from the option board, Click on ReadUnit!. The radio and RIB should be powered down for 3 seconds after reading or programming. Gerneral Info
Unit Information: Provides general information regarding the currently connected unit
16
General Settings
Beep Options > Power Up: Enables a short beep sequence that takes place immediately after power-up. Beep Options > Error: This beep may be triggered by any input event if programmed to do so. For example, if a long press on the Mode Input is not assigned to a function, it may be configured to generate the error beep. Beep Options > Mode: This is used to indicate to the user when the mode has been enabled/disabled (i.e.. Beep Options > Go Ahead: This is a local beep out the speaker to indicate to the user that ANI has been sent and it is okay to talk. Beep Options > Wake Up Beep: Enables a short beep to be sent over the air immediately after PTT is pressed. Enabling this beep is recommended when the 'Wake on VOX' feature is used. Beep Options > Courtesy Beep: If selected, once the unit is done retransmitting the recorded audio it will generate a courtesy tone to let others know it is done retransmitting. Voice Compression: If left unchecked the VAE-1 can store up to a 2.25-minute voice message. If checked the VAE-1 can store up to a 3-minute voice message, but with a diminished level of audio quality.
17
Signaling > Settings
Common PTT: If PTT in and out are connected to the same point, check this box. Trunking Delay Enable: Check this box if using a trunking system. This will cause the unit to hold off transmitting the ANI until it has received a channel acquisition acknowledgement from the radio. Key-Up Delay: This sets the amount of time the unit waits after keying the radio before it transmitting the ANI. CAD Settings > System ID: Feature not used in this product. Warning: When reading the information programmed into a unit, the System ID digits will display as all 0's so that the System ID is not compromised if a unit is stolen. For this reason, units cannot be 'cloned'. CAD Settings > Group ID: This is the 3-digit group ID of the unit. This is the number used by the dispatcher when placing a group call. Valid digits are 0-9 and A-F CAD Settings > Individial ID: This is the 5-digit individual ID of the unit. This is the number, along with the Group ID is used by the dispatcher when placing an individual call. Valid digits are 0-9 and A-F. CAD Settings > Enable FMP Decode: This box must be checked to enable the decode functions. CAD Settings > Polite Transpond: Normally, if the unit is required to transpond in response to a command from the dispatcher, it will do so immediately after receiving the command. Checking this box will cause the unit to check for a channel busy indication (using COR or VOX) before transponding. If the channel is busy, the transpond will be postponed until the channel is no longer busy. CAD Settings > Spy Duration: The Spy function allows to dispatcher to remotely key a unit and listen to microphone audio. This setting specifies the amount of time the unit will stay keyed after receipt of the Spy command. The options are 15, 30, 45 and 60 seconds. CAD Settings > Number of Rings: The dispatcher may selectively call an individual unit, a group of units, or all units. When called, the unit will ring the number of times specified by this setting. The options are 1, 3, 5, or 7 rings.
18
Signaling > ANI
Enable ANI: Checking this box will enable the ANI feature of the unit. Signal Position Settings: This can be set for the beginning of transmission (leading), end of transmission (trailing) or both. Protocol Format: Select the desired signaling format in which the ANI and ENI will be transmitted. Unit ID: This sets ANI of the unit. Note: See Unit ID based on Protocal format Chart in the Technical Notes section at the end of this manual. Tone Duration: This field only applies to DTMF and 5-Tone formats and sets the length of each tone. Tone Gap Duration: This field only applies to DTMF and sets the length of the gap between tones. Repeat Delay: This sets the time after sending an ANI that the unit will wait before sending another ANI.
19
Signaling > ENI
Enable ENI: Checking this box will enable the ENI feature of the unit. Note: The ENI feature of the unit must be enabled in order to transmit voice alarms FMP Signaling Options > FMP: By checking this box, a FMP packet will be generated. If the this checkbox is under Leading or Trailing, it will be sent at that part of that transmission event. If the checkbox is located under an Emergency section, it will be sent during an Emergency transmission event Protocol Format: This displays the format selected on the ANI tab. Unit ID: This sets the Emergency ANI of the unit. Transmit Forever: If selected the ENI will transmit continuously at the repeat interval until canceled. Busy Lockout: When it is time to transmit an ENI sequence, if this box is not checked the transmission will take place regardless of whether or not the channel is busy. If this box is checked and the channel is busy (as indicated by COR or VOX), the ENI will not be transmitted. Instead, the unit will wait 2.5 seconds and then check again to see if the channel is busy. If the channel is not busy at that time, the ENI sequence will be transmitted. If not, the process will repeat indefinitely. Transmit Count: This sets the number of times the ENI will be sent. Repeat Interval: This sets the time between ENI transmissions. Options > PTT Resets/Cancels ENI: If selected, pressing the PTT button will either reset the Lone Worker’s Transmit Delay time or cancel the transmission of the ENI. Options > Live Mic Enable: If selected the unit will enable the mic of the radio to transmit mic audio to the dispatcher. Options > Revert to Clear: Currently not used. Options > Locator Tone Enable: If selected the unit will emit tones out of the radio’s speaker. Note: The locator tones do not begin emitting until the unit has sent the pre-programmed amount of ENI transmissions. No tones will be emitted if the ENI has been programmed to repeat forever or if the ENI transmission is canceled.
20
Signaling > Lone Worker
Enable Lone Worker: Checking this box will enable the Lone Worker feature of the module. Transmit Delay: In Lone Worker mode, if the user does not interact with the radio before this amount of time passes, the ENI sequence will be transmitted. This time is in seconds. Warning Tone Enable: This will generate a tone sequence to alert the user the ENI is about to be transmitted. Warning Tone Delay: In Lone Worker mode, if the user does not interact with the radio before this amount of time passes, the emergency warning tone will be sounded. This amount of time must be less than that of the Transmit Delay for the warning tone to be sounded. Also, the Warning Tone Enable box must be checked for the tone to be sounded. For example, based on the screen shown above after 105 seconds of no activity the unit will generate warning tones. The user then has 15 seconds to interact with the radio to keep the Transmit Delay time of 120 seconds expiring and the ENI being transmitted. Continuous Warning Enable: This will generate a constant tone to alert the user the ENI is about to be transmitted. Power-up with Lone Worker on: If checked the unit will be in Lone Worker mode when the radio is turned on. This eliminates the need for the user to use the mode input to turn the Lone Worker mode on. Motion Resets Delay Timers: The unit can then use the accelerometer to detect motion based on the Motion Sensitivity setting to determine if the user is in distress in addition to requiring interaction with the radio. Motion Sensitivity: This sets a level of motion required to reset the Transmit Delay timer. Some work environments may have an inherent level of motion that would be detected by lower settings of the accelerometer, so a higher level of sensitivity might be needed. Midian recommends experimenting to determine the best sensitivity setting for the work environment.
21
Signaling > Ani Muting
Mute FMP/GPS or MDC-1200 ANI Packets: Checking this box causes the module to mute all incoming data packets preventing all except a short “chirp” from being heard by the user. Mute Duration: If muting of GPS or MDC-1200 Packets is enabled, the receiver will be muted for this amount of time after the premable tone at the beginning of the packet is detected. For Midian GPS packets, this should be set to 280 ms (default). If muting of MDC-1200 packets is desired, this should be set to 170 ms. Packet Detector Sensitivity: This setting controls the sensitivity of the preamble tone detector which triggers the muting of packets. If it is too sensitive (higher number), voice may cause the detector to trigger resulting in voice being muted when it should not be. If it is not sensitive enough (lower number), the detector may not trigger when it is supposed to. Adjust the sensitivity up or down as needed to achieve the desired results.
22
Voice Alarm
Transmit Frequency: When an ENI sequence is triggered the unit sends an Emergency ANI either once or multiple times. This field tells the unit to send the voice alarm with the emergency ANI only on the first Emergency ANI or on all Emergency ANI’s. Require PTT to Record: Most radios will only pass audio to the option board when PTT is pressed. If this is the case this box must be checked. In this mode a button is used to put the unit in record mode and then the PTT is pressed to pass audio to the unit. The unit keeps the audio from being transmitted in record mode, but only if the PTT path is broken. Auto Review: After message recording is completed the unit will replay the message over the speaker to confirm the message. Save Message When Powered Off: This will keep the last recorded message in memory when power is cycled. Auto Record: If checked the unit will start to record immediately upon power up. If the Require PTT to Record box is checked it will wait for the PTT.
23
Audio Levels > Tone
Beep Volume: Adjust the slider for the desired beep volume. This level is expressed as a percentage of max voice audio level. Over-The-Air-Signal Modulation: Adjust the slider for the desired beep volume. This level is expressed as a percentage of max voice audio level. For these radios Midian recommends using 78%. Audio Levels > Playback
Playback Level: This controls the audio level when a stored voice message is played back on the radio speaker. If voice playback is too low or too loud, adjust this level accordingly. Transmit Level: This controls the audio level when a stored voice message is retransmitted over the air. If the transmit level is too low or too loud, adjust this level accordingly.
24
Audio Levels > Voice
Note: See the Audio Levels section of this manual on Page 26 before adjusting these settings Button Assignment
Short Press: This is a press and immediate release press. Long Press: This is a press, hold until beeps are heard and release press. The buttons can be programmed for Emergency ANI, Lone Worker On/Off, etc.
25
Basic Settings
Radio Type: Select from the list the Radio Type that matches your radio. Enable Mode LED: Not used in this product. Enable LCD Messages: Not used in this product. Use Accessory Pin for Mode Input (mobile only): Not used in this product. Use Accessory Pin for Emergency Input (mobile only): On mobile radios, an accessory pin be used to activate the emergency feature of the option board (Note: not all boards have this feature). This is useful, for example, if you want to use a foot switch to send an emergency signal. The emergency feature is activated when the pin is at the active level as programmed via the radio CPS. The way this feature is set up depends on radio type as follows: MDC AND LTR MOBILES In the radio CPS on the ‘Accessory Pins’ screen, program the chosen pin to be ‘Option Board 2 (input). That pin can now be used to control the emergency feature. 5-TONE AND MPT MOBILES In the radio CPS in the ‘Per Radio GP I/O Lines’ screen, program pin 8 to be ‘Inform Option Board Only’. Pin 8 can now be used to control the emergency feature.
26
Advanced Settings
Note: These settings should be left “as is” and only adjusted when advised to do so by a Midian technician. Note: Enable Audio PA control must be checked to review recorded message.
27
AUDIO LEVELS ALIGNMENT
This discussion applies when audio level settings are unknown. We have pre-determined these for the PRO/COM radios and they appear in the chart below. Audio Levels Overview: To ensure the best audio quality, the unit must be configured to match the audio levels used by the radio. The unit uses programmable gain amplifiers to accomplish this. Determining the gain settings for these amplifiers is an involved process, so Midian simplified this process by developing an algorithm that requires the technician to make only four voltage measurements. From these four measurements, all of the many internal settings are determined. Still, getting the best audio quality will likely require a bit of trial and error. The unit only has control of audio voltage levels, not input and output impedances. These impedances can dramatically influence the levels. The Four Voltage Measurements: An oscilloscope and a communications test set/service monitor are required for the measurements. It is recommended that the measurements be recorded in units of mV peak-to-peak. Each measurement must be taken with system modulation at either 60% or 100%, but Midian recommends using 60% A method for controlling transmit modulation is required for accurate measurements in the TX mode. A small speaker held in place near the microphone by a rubber band can serve this purpose in most cases. Use a sine-wave generator to inject a 1000 Hz tone into the speaker. Adjust the output of the sine wave generator so that the transmitter produces 60% of rated modulation while PTT is pressed. Note that if the audio source (such as a speaker) is moved even slightly, the TX modulation may change significantly. Care must be taken to avoid changing the TX modulation while taking the measurements. The first two measurements must be taken using a radio that has not been modified. The 2nd two measurements require that the unit is installed and power is applied to the radio. These measurements must be taken within 15 seconds of powering on the radio/unit. This is because the unit may enter power saving mode after that time. Measurements made while the unit is in power saving mode will not be valid. The unit ships with the power save feature enabled by default. The power save feature can be disabled via the KL-3 programming software so that it will not interfere with taking measurements, if desired. Please note that the levels provided to the option board are different between narrow band and wide band. 1. TX Input: The goal of this procedure is to determine the audio level that the unit will see at the TX audio
pickup point after it is installed. The unit must be installed and powered-on while making this measurement. Use the TX Alignment Set-Up procedure and measure the audio level at TP1 on the unit.
2. RX Input: The goal of this procedure is to determine the audio level that the unit will see at the RX audio
pickup point after it is installed. The unit must be installed and powered-on while making this measurement. Use the TX Alignment Set-Up procedure and measure the audio level at TP2 on the unit.
3. In the programming software under audio levels set the TX In to the same level as measured in step 1 and for
a preliminary adjustment set the TX Out for the same level. Set the RX In to the same level as measured in step 2 and for a preliminary adjustment set the RX Out for the same level. Program the unit.
4. RX Output: The goal of this procedure is to determine the audio level that would normally appear at the RX
audio insertion point in an unmodified radio. Using the same RX Alignment Set-Up procedure verify the audio level at the speaker is still at the same level measured initially in the RX Alignment Set-Up procedure. If not adjust the RX Out level accordingly.
5. TX Output: The goal of this procedure is to determine the audio level that would normally appear at the TX
audio insertion point in an unmodified radio. Using the same TX Alignment Set-Up procedure verify the modulation is still at 60%, if not adjust the TX Out level accordingly.
28
Programming the Audio Levels:
After determining the audio levels at the audio hookup points, it will be necessary to program the unit to match these levels. In the programming software, there is a slider control on the Audio Levels Screen for each of the of four audio hookup points. Locate the column that corresponds to the modulation and units of measurement for each of the audio hookup points. Adjust the slider bar such that the value appearing in the appropriate column matches what was measured as closely as possible. Midian recommends the following values based on 60% modulation in mVpp: Radio Model RX In TX In RX Out TX Out CP-140, EP-450, GP-3688, PR-400 726 144 180 144 CM-160, CM-300, CM-360, EM-400, GM-3688, PM-400 744 156 180 150
29
OPERATION
ANI Encode: Pressing PTT causes ANI to be transmitted. ENI Encode: Activating the emergency input causes the ENI to be transmitted. Lone Worker Enable: The Lone Worker feature can be enabled upon power up or using the Mode Input or Emergency Input. Lone Worker Reset: If the Lone Worker feature is being used, pressing the PTT or pressing the button assigned to Lone Worker Reset will reset the Transmit Delay timer. If the Warning Tone Delay time expires the unit will generate warning tones to indicate to the user that the Lone Worker feature is about to send an ENI if the unit does not see PTT or Lone Worker Reset activity. If the Transmit Delay time then expires the unit will send the ENI. Message Recording on Power Up: If the Auto Record feature is enabled the unit will record a voice message immediately upon power up. If the radio requires PTT to pass voice to the option board and the Require PTT to Record box is checked, the unit will wait to record until the PTT is pressed. Message Recording with Mode Button: Using the button(s) set for controlling record start and stop, press the button in the manner programmed in Mode Input to start recording. If the radio requires PTT to pass voice to the option board and the Require PTT to Record box is checked, the unit will wait to record until the PTT is pressed. When recording is completed, press the button in the manner programmed in Mode Input to stop recording. When the recording is stopped the unit will play back the recorded message if the Auto Review box is checked.
TECHNICAL NOTES
30
Radio Compatibility: Midian has taken the utmost care to ensure the option board integrates into the radio with minimal impact to the features of the radio. However, some features may not be available in the radio when an option board is used. If a feature is not available, please contact Midian to see if the feature can be added. Radio Firmware: Midian recommends having the latest firmware in the radio when installing the option board. However, it should be noted that occasionally firmware updates may cause a conflict with proper option board/radio communications. This may appear that the option board is not working properly, but it is a conflict in the serial communication between the option board and radio. If this happens it will be necessary to go back to the original firmware revision. Please note that firmware versions between the EMEA region and the Asia and America regions might be different. Known Issues: Mobiles: 1. The radio must be off for a full 3 seconds prior to being turned on or the module cannot reset properly
resulting in malfunction. 2. The "Enable LCD Message" option in the MPS software should not be enabled due to problems in the radio. 3. Not all button assignments available via the MPS software work with this radio. When assigning buttons to the
module via the MPS software, the actual assignments vary from what is selected on the screen. Please refer to the following list, which shows the actual assignment that will take place for each possible selection: SELECTED BUTTON ACTUAL BUTTON P1 P2 short press P2 P2 long press P3 P3 short press P4 P3 long press
Note: Depending on the radio firmware version the P2 button may not be available for option board use. 4. Upon power-up, the radio does not always report the state of the accessory pins to the option board. It may
be necessary to toggle the state of these inputs once after power-up to ensure correct operation. Known Issues: Portables: 1. The radio must be off for a full 3 seconds prior to being turned on or the option board cannot reset properly
resulting in malfunction.
2. Side button #3 and top button selections available via the MPS programming are not applicable to this radio. Option Board Feature: Enabling the option board feature tells the radio to report events such as button press, PTT press, carrier detect, etc. to the option board. This feature enables communication between the option board and the radio. When controlling the option board with a radio button, it is absolutely required to enable this feature on all channels. For ANI on a per channel basis only enable the option board on ANI channels. On display models, the following icon appears on the LCD when option board mode is on:
31
Unit ID based on Protocal format: DTMF - Up to 8 digits using 0123456789*#ABCD CCIR - Up to 8 digits using 0123456789ABCDEF EEA - Up to 8 digits using 0123456789ABCDEF EIA - Up to 8 digits using 0123456789ABCDEF ZVEI - Up to 8 digits using 0123456789ABCDEF DZVEI - Up to 8 digits using 0123456789ABCDEF DDZVEI - Up to 8 digits using 0123456789ABCDEF NATEL - Up to 8 digits using 0123456789ABCDEF MODAT - Up to 8 digits using 0123456789E PCCIR - Up to 8 digits using 0123456789ABCDE PZVEI - Up to 8 digits using 0123456789ABCDEF PDZVEI - Up to 8 digits using 0123456789ABCDE MDC-1200 - Up to 4 digits using 0123456789ABCDEF FleetSync - Up to 4 digits using 0123456789 Range: 1000 to 3999 GE-Star - Up to 5 digits using 0123456789 Range: 0 to 16383
MIDIAN CONTACT INFORMATION
MIDIAN ELECTRONICS, INC. 2302 East 22nd Street Tucson, Arizona 85713 USA Toll-Free: 1-800-MIDIANS Main: 520-884-7981 E-mail: [email protected] Web: HUwww.midians.comU
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
16
15
33
35
36
37
38
3
11
12
20
46
21
2
39
40
41
42
32 31 13 10 45 1743
30
29
26
27
28
5 14 34 44
1
4
67
8
9
18
19
22
23
24
25
47
48
U3
16
13
42
11
9
4
3
37
8
47
28
24
27
20
18
36
43
46
48
45
41
644
1 2 3840 39
34
21
22
7
35
17
19
29
25
2326
12
10
5
15
14
33323031
49
U1
7 482 5
16 3 U4
-
+
13
1214
U7:4
-
+
9
108U7:3
-
+
2
31
114
U7:1
-
+
6
57U7:2
47KR2 +3.3V
*R1
560pC1
+3.3V
560pC2
47KR7
47KR6
IN11
ENA3
GN
D2
RES
4
OUT 5
VR1
IN11
ENA3
GN
D2
RES
4
OUT 5
VR2
IN11
ENA3
GN
D2
RES
4
OUT 5
VR3
560pC4
100KR15
100KR14
+3.3VDD.1uC7
2RR49
2RR50
2RR51
+3.3V
+3.3VA
+3.3VDD
8.2KR16
27KR13
.1uC10
.01uC9
4.7KR8
+3.3V
VAN
.0068uC15
.0068uC16
*C17
56KR18
36KR21
.001uC18
75KR19
VAN
1.2MR20
VAN
VAN
+3.3V
+3.3V
VAN
TP5
TP12
TP3
TP4
TP1
TP2
3.3KR28
.01uC45
2.2uC26
2.2uC27
P4:4
P4:3
P4:2
P4:1
P4:5
P4:6
P3:
1
P3:
2
P3:
3
P3:
4
P3:
5
P3:
6
.1uC28
.1uC29
.1uC30
.1uC31
10uC36
10uC35
10uC32
Y1
+3.3V
+3.3V
+3.3VDD
+3.3VA
+3.3V
2.2uC13
VDDD
.01uC47
PROG_INPROG_INPI
PROG_OUTPROG_OUTPO
4.7KR30
+3.3V
47KR31
+3.3V
VDDD
VDDD
4.7KR55
4.7KR54
100KR34
100KR35
560pC37
.1uC41
10uC40+3.3V
0RL1
SW_B+
SRD_SND
TP17
10KR9.1u
C12
100pC14
10K1%R11
10K1%R12
10KR10
3
1
2
4
5 6
U5
39pC44
.1uC25
.01uC21
2.2uC20
560pC19
3.3KR24
*R17
TP8
TP18
TP7
TP6
SCK_SND
*C48
PTT_OUT
VDDD
0RR32
*C50
*C49
PTT_OUT
*C52
4001Q1
4001Q2
*Q6
0RR52
SB1D1
SB1D2
SB1D4
SB1D3
560pC11
0RR57
0RR58
47KR36 +3.3V
+3.3V
.1uC43
.1uC42
CS1
SO2
SI5
SCK6
VCC 8
HOLD 7
WP 3
GND 4
AT26DF081AU6
.22uC33
22pC24
*C51
CS7
SO12
SI13
SCK14
DVDD 1
INT29 INT18
GND 2MMA7455L
AVDD 6
GND 5
IADDR0 4
N/C 3
GND 10
GND 11
U10
4.7uC5
4.7uC53
47KR3
47KR4 +3.3V
+3.3V
*R26VDDD
SW +BP2:8
GNDP2:11
VDDDP2:12
PTT_INP2:13
RESETP2:14
MISOP2:15
MOSIP2:16
CLKP2:17
OPT_ENA
P2:18
RDYP2:19
GNDP2:20
RX_OUTP2:23
RX_INP2:25
TX_OUTP2:26
DIS_INP2:27
TX_INP2:28
SB1
D6
*R5
*R25
+3.3V
GND
100pC105
100pC106
100pC107
100pC108
100pC109
100pC113
BL_EN
BL_EN
GND
*
R22 *R23
+3.3V
100pC39
12pC38
CP
CJS2012-04-05 DML
2013-08-06
B-2
1 of 1 7726
MIDIAN ELECTRONICS, INC.DATE:
DESIGN:
DWN BY:
REV:
APPR
COPYRIGHT ©
REV
SHEET PROJECT NUMBER
DOCUMENT NAME
SCHEMATIC2013
VAE-1-MC1
NOTES:
* = NOT INSTALLED
PIC101
PIC102COC1
PIC201
PIC202COC2
PIC401
PIC402COC4 PIC501
PIC502COC5
PIC701
PIC702COC7
PIC901 PIC902
COC9
PIC1001
PIC1002COC10
PIC1101 PIC1102
COC11
PIC1201 PIC1202
COC12
PIC1301
PIC1302COC13
PIC1401
PIC1402COC14
PIC1501 PIC1502
COC15
PIC1601 PIC1602
COC16
PIC1701 PIC1702
COC17
PIC1801
PIC1802COC18
PIC1901
PIC1902COC19 PIC2001
PIC2002COC20
PIC2101 PIC2102
COC21
PIC2401
PIC2402COC24
PIC2501 PIC2502
COC25PIC2601
PIC2602COC26PIC2701
PIC2702COC27
PIC2801 PIC2802
COC28
PIC2901 PIC2902
COC29
PIC3001 PIC3002
COC30
PIC3101
PIC3102COC31 PIC3201
PIC3202COC32
PIC3301 PIC3302
COC33
PIC3501 PIC3502
COC35
PIC3601 PIC3602
COC36
PIC3701
PIC3702COC37
PIC3801
PIC3802COC38
PIC3901
PIC3902COC39
PIC4001 PIC4002
COC40
PIC4101 PIC4102
COC41
PIC4201 PIC4202
COC42
PIC4301 PIC4302
COC43
PIC4401
PIC4402COC44
PIC4501
PIC4502COC45
PIC4701 PIC4702
COC47
PIC4801 PIC4802
COC48
PIC4901 PIC4902
COC49
PIC5001 PIC5002
COC50
PIC5101
PIC5102COC51
PIC5201
PIC5202COC52
PIC5301
PIC5302COC53
PIC10501
PIC10502COC105
PIC10601
PIC10602COC106
PIC10701
PIC10702COC107
PIC10801
PIC10802COC108
PIC10901
PIC10902COC109
PIC11301
PIC11302COC113
PID101PID102
COD1
PID201PID202
COD2
PID301PID302
COD3
PID401PID402
COD4
PID601PID602
COD6
PIL101
PIL102
COL1
PIP208COP2:8
PIP2011COP2:11
PIP2012COP2:12
PIP2013COP2:13
PIP2014COP2:14
PIP2015COP2:15
PIP2016COP2:16
PIP2017COP2:17
PIP2018COP2:18
PIP2019COP2:19
PIP2020COP2:20
PIP2023COP2:23
PIP2025COP2:25
PIP2026COP2:26
PIP2027COP2:27
PIP2028COP2:28
PIP301
COP3:1PIP302
COP3:2PIP303
COP3:3PIP304
COP3:4PIP305
COP3:5PIP306
COP3:6
PIP401 COP4:1
PIP402 COP4:2
PIP403 COP4:3
PIP404 COP4:4
PIP405 COP4:5
PIP406 COP4:6
PIPI01
COPI
PIPO01
COPO
PIQ10DPIQ10G
PIQ10S
COQ1
PIQ20DPIQ20G
PIQ20S
COQ2
PIQ60DPIQ60G
PIQ60S
COQ6
PIR101 PIR102
COR1
PIR201 PIR202
COR2
PIR301 PIR302
COR3
PIR401 PIR402
COR4
PIR501 PIR502
COR5
PIR601 PIR602
COR6
PIR701 PIR702
COR7
PIR801 PIR802
COR8
PIR901 PIR902
COR9 PIR1001 PIR1002
COR10
PIR1101 PIR1102
COR11 PIR1201 PIR1202
COR12
PIR1301
PIR1302
COR13
PIR1401
PIR1402
COR14
PIR1501
PIR1502
COR15PIR1601
PIR1602
COR16
PIR1701 PIR1702
COR17
PIR1801 PIR1802
COR18PIR1901 PIR1902
COR19
PIR2001 PIR2002
COR20
PIR2101 PIR2102
COR21
PIR2201
PIR2202COR22
PIR2301 PIR2302
COR23
PIR2401 PIR2402
COR24
PIR2501 PIR2502
COR25
PIR2601 PIR2602
COR26
PIR2801 PIR2802
COR28
PIR3001
PIR3002
COR30
PIR3101
PIR3102
COR31
PIR3201 PIR3202
COR32
PIR3401 PIR3402
COR34
PIR3501 PIR3502
COR35
PIR3601 PIR3602
COR36
PIR4901 PIR4902
COR49
PIR5001 PIR5002
COR50
PIR5101 PIR5102
COR51
PIR5201 PIR5202
COR52
PIR5401 PIR5402
COR54
PIR5501 PIR5502
COR55
PIR5701 PIR5702
COR57
PIR5801 PIR5802
COR58
COtb0sch1
PITP101
COTP1
PITP201
COTP2
PITP301
COTP3
PITP401
COTP4
PITP501
COTP5
PITP601 COTP6
PITP701
COTP7
PITP801
COTP8
PITP1201
COTP12
PITP1701
COTP17
PITP1801
COTP18
PIU101 PIU102
PIU103
PIU104
PIU105
PIU106
PIU107
PIU108
PIU109
PIU1010
PIU1011
PIU1012PIU1013
PIU1014
PIU1015
PIU1016
PIU1017
PIU1018
PIU1019
PIU1020
PIU1021
PIU1022
PIU1023
PIU1024
PIU1025
PIU1026
PIU1027
PIU1028
PIU1029
PIU1030
PIU1031
PIU1032
PIU1033
PIU1034
PIU1035
PIU1036
PIU1037
PIU1038PIU1039PIU1040
PIU1041
PIU1042
PIU1043
PIU1044
PIU1045
PIU1046
PIU1047
PIU1048
PIU1049
COU1
PIU301
PIU302
PIU303 PIU304
PIU305
PIU306
PIU307
PIU308
PIU309
PIU3010
PIU3011
PIU3012
PIU3013
PIU3014
PIU3015
PIU3016
PIU3017PIU3018
PIU3019
PIU3020
PIU3021
PIU3022
PIU3023
PIU3024
PIU3025
PIU3026
PIU3027
PIU3028
PIU3029
PIU3030
PIU3031PIU3032
PIU3033 PIU3034
PIU3035
PIU3036
PIU3037
PIU3038
PIU3039
PIU3040
PIU3041
PIU3042
PIU3043
PIU3044
PIU3045
PIU3046
PIU3047
PIU3048
COU3
PIU401
PIU402
PIU403
PIU404
PIU405
PIU406
PIU407PIU408
COU4
PIU501
PIU502
PIU503
PIU504
PIU505 PIU506
COU5
PIU601
PIU602
PIU603
PIU604
PIU605
PIU606
PIU607
PIU608
COU6
PIU701
PIU702
PIU703
PIU704
PIU7011
COU7:1
PIU705
PIU706
PIU707COU7:2
PIU708
PIU709
PIU7010
COU7:3
PIU7012
PIU7013
PIU7014
COU7:4
PIU1001
PIU1002
PIU1003
PIU1004
PIU1005
PIU1006
PIU1007
PIU1008
PIU1009
PIU10010
PIU10011
PIU10012
PIU10013
PIU10014
COU10
PIVR101
PIVR102
PIVR103
PIVR104
PIVR105
COVR1
PIVR201
PIVR202
PIVR203
PIVR204
PIVR205
COVR2
PIVR301
PIVR302
PIVR303
PIVR304
PIVR305
COVR3
PIY101
PIY102COY1
PAC102 PAC101COC1
PAC202 PAC201COC2
PAC402 PAC401COC4
PAC502 PAC501COC5
PAC702
PAC701
COC7
PAC902
PAC901COC9 PAC1002
PAC1001COC10
PAC1102 PAC1101COC11
PAC1202
PAC1201COC12
PAC1302 PAC1301COC13
PAC1402
PAC1401COC14
PAC1502
PAC1501COC15PAC1602 PAC1601COC16
PAC1702PAC1701COC17
PAC1802PAC1801COC18
PAC1902
PAC1901COC19PAC2002
PAC2001COC20
PAC2102
PAC2101COC21
PAC2402
PAC2401COC24
PAC2502 PAC2501COC25
PAC2602
PAC2601COC26
PAC2702
PAC2701COC27
PAC2802PAC2801COC28
PAC2902PAC2901COC29
PAC3002PAC3001COC30
PAC3102
PAC3101
COC31
PAC3202
PAC3201COC32
PAC3302
PAC3301COC33PAC3502
PAC3501COC35PAC3602
PAC3601COC36
PAC3702 PAC3701COC37
PAC3802
PAC3801COC38
PAC3902
PAC3901COC39
PAC4002PAC4001COC40
PAC4102PAC4101COC41
PAC4202
PAC4201COC42
PAC4302
PAC4301COC43
PAC4402
PAC4401COC44
PAC4502
PAC4501COC45
PAC4702
PAC4701COC47
PAC4802PAC4801COC48
PAC4902
PAC4901COC49
PAC5002PAC5001COC50
PAC5101
PAC5102
COC51
PAC5202
PAC5201COC52
PAC5302 PAC5301COC53
PAC10102
PAC10101COC101PAC10202
PAC10201COC102PAC10302
PAC10301COC103PAC10402
PAC10401COC104PAC10502
PAC10501COC105PAC10602
PAC10601COC106
PAC10702PAC10701COC107
PAC10802
PAC10801COC108PAC10902
PAC10901COC109PAC11002
PAC11001COC110PAC11102
PAC11101COC111PAC11202
PAC11201COC112PAC11302
PAC11301COC113
PAD101
PAD102
COD1
PAD201PAD202COD2
PAD301 PAD302COD3
PAD401 PAD402COD4
PAD601
PAD602
COD6
PAL102
PAL101COL1
PAP2030PAP2029PAP201PAP202PAP203PAP204 PAP205PAP206 PAP207PAP208PAP209PAP2010PAP2011PAP2012PAP2013PAP2014PAP2015PAP2016 PAP2017PAP2018 PAP2019PAP2020PAP2021PAP2022PAP2023PAP2024PAP2025 PAP2026PAP2027 PAP2028
COP2
PAP304PAP306 PAP303PAP305 PAP302 PAP301COP3
PAP404 PAP406PAP403 PAP405PAP402PAP401 COP4
PAPI01COPI
PAPO01COPO
PAQ10S
PAQ10D
PAQ10GCOQ1
PAQ20SPAQ20D
PAQ20GCOQ2
PAQ60S
PAQ60D
PAQ60GCOQ6
PAR102 PAR101COR1
PAR202PAR201COR2
PAR302 PAR301COR3
PAR402PAR401COR4
PAR502
PAR501COR5
PAR602PAR601COR6
PAR702PAR701COR7
PAR802
PAR801COR8 PAR902PAR901COR9
PAR1002 PAR1001COR10
PAR1102
PAR1101COR11
PAR1202
PAR1201COR12
PAR1302PAR1301COR13 PAR1402
PAR1401COR14
PAR1502
PAR1501COR15
PAR1602
PAR1601COR16
PAR1702
PAR1701COR17
PAR1802PAR1801COR18
PAR1902
PAR1901COR19
PAR2002
PAR2001COR20 PAR2102
PAR2101COR21
PAR2202
PAR2201COR22
PAR2302
PAR2301COR23
PAR2402
PAR2401COR24
PAR2502PAR2501COR25
PAR2602 PAR2601COR26
PAR2802
PAR2801COR28
PAR3002
PAR3001COR30
PAR3102 PAR3101COR31
PAR3202PAR3201COR32
PAR3402PAR3401COR34PAR3502
PAR3501COR35
PAR3602
PAR3601COR36
PAR4902
PAR4901COR49
PAR5002
PAR5001COR50
PAR5102
PAR5101COR51
PAR5202 PAR5201COR52
PAR5402 PAR5401COR54
PAR5502 PAR5501COR55
PAR5702
PAR5701COR57
PAR5802PAR5801COR58
COtb0sch1
PATP101COTP1
PATP201COTP2
PATP301COTP3
PATP401COTP4
PATP501COTP5
PATP601COTP6
PATP701
COTP7
PATP801 COTP8
PATP1201COTP12
PATP1701COTP17
PATP1801COTP18
PAU1049PAU1048PAU1047PAU1046PAU1045PAU1044PAU1043PAU1042PAU1041PAU1040PAU1039PAU1038PAU1037
PAU1036PAU1035PAU1034PAU1033PAU1032PAU1031PAU1030PAU1029PAU1028PAU1027PAU1026PAU1025PAU1024PAU1023PAU1022PAU1021PAU1020PAU1019PAU1018PAU1017PAU1016PAU1015PAU1014PAU1013
PAU1012PAU1011PAU1010PAU109 PAU108PAU107 PAU106PAU105PAU104PAU103PAU102 PAU101
COU1
PAU3048PAU3047PAU3046PAU3045PAU3044PAU3043PAU3042PAU3041PAU3040PAU3039PAU3038PAU3037
PAU3036PAU3035PAU3034PAU3033PAU3032PAU3031PAU3030 PAU3029PAU3028 PAU3027PAU3026PAU3025PAU3024PAU3023PAU3022PAU3021PAU3020PAU3019PAU3018PAU3017PAU3016PAU3015PAU3014PAU3013
PAU3012PAU3011PAU3010PAU309PAU308PAU307PAU306PAU305PAU304PAU303PAU302PAU301
COU3
PAU401PAU402PAU403PAU404PAU405
PAU406PAU407PAU408
COU4
PAU501PAU502PAU503PAU504
PAU505PAU506
COU5
PAU608
PAU607
PAU606
PAU605PAU604
PAU603
PAU602
PAU601
COU6
PAU701PAU702PAU703PAU704PAU705PAU706PAU707 PAU708
PAU709PAU7010PAU7011PAU7012PAU7013PAU7014
COU7
PAU10014PAU10013PAU10012PAU10011PAU10010PAU1009PAU1008 PAU1007 PAU1006
PAU1005PAU1004PAU1003PAU1002PAU1001
COU10
PAvariant101PAvariant102
PAvariant1028PAvariant1027PAvariant1026PAvariant1025PAvariant1024PAvariant1023PAvariant1022PAvariant1021PAvariant1020PAvariant1019PAvariant1018PAvariant1017PAvariant1016PAvariant1015PAvariant1014PAvariant1013PAvariant1012PAvariant1011PAvariant1010PAvariant109PAvariant108PAvariant107PAvariant106PAvariant105PAvariant104PAvariant103
PAvariant1029 PAvariant1030
PAvariant10G
PAvariant10D
PAvariant10S
PAvariant1031 PAvariant1032 PAvariant1033 PAvariant1034 PAvariant1035 PAvariant1036PAvariant1037
PAvariant1038
PAvariant1039
PAvariant1040
PAvariant1041
PAvariant1042
PAvariant1043
PAvariant1044
PAvariant1045
PAvariant1046
PAvariant1047
PAvariant1048
PAvariant1049
PAvariant100 COvariant1COvariant3
PAVR105PAVR102
PAVR104
PAVR101
PAVR103COVR1
PAVR205
PAVR202
PAVR204
PAVR201 PAVR203
COVR2
PAVR305
PAVR302
PAVR304
PAVR301PAVR303COVR3PAY101
PAY102COY1
COtb0sch2
PAvariant201
PAvariant2049
PAvariant200 COvariant2
1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
16
15
33
35
36
37
38
3
11
12
20
46
21
2
39
40
41
42
32 31 13 10 45 1743
30
29
26
27
28
5 14 34 44
1
4
67
8
9
18
19
22
23
24
25
47
48
U3
16
13
42
11
9
4
3
37
8
47
28
24
27
20
18
36
43
46
48
45
41
644
1 2 3840 39
34
21
22
7
35
17
19
29
25
2326
12
10
5
15
14
33323031
49
U1
7 482 5
16 3
U4
-
+
13
1214
U7:4
-
+
9
108U7:3
-
+
2
31
114
U7:1
-
+
6
57U7:2
47KR2 +3.3V
*R1
560pC1
+3.3V
560pC2
47KR7
47KR6
IN11
ENA3
GN
D2
RES
4
OUT 5
VR1
*
IN11
ENA3
GN
D2
RES
4
OUT 5
VR2
5206
IN11
ENA3
GN
D2
RES
4
OUT 5
VR3
560pC4
100KR15
100KR14
+3.3VDD.1uC7
2RR49
2RR50
2RR51
+3.3V
+3.3VA
+3.3VDD
8.2KR16
27KR13
.1uC10
.01uC9
4.7KR8
+3.3V
VAN
.0068uC15
.0068uC16
*C17
56KR18
36KR21
.001uC18
75KR19
VAN
1.2MR20
VAN
VAN
+3.3V
+3.3V
VAN
TP5
TP12
TP3
TP4
TP1
TP2
3.3KR28
.01uC45
2.2uC26
2.2uC27
P4:4
P4:3
P4:2
P4:1
P4:5
P4:6
P3:1
P3:2
P3:3
P3:4
P3:5
P3:6
.1uC28
.1uC29
.1uC30
.1uC31
10uC36
10uC35
10uC32
Y1
+3.3V
+3.3V
+3.3VDD
+3.3VA
+3.3V
.1uC13
VDDD
.01uC47
PROG_INPROG_INPI
PROG_OUTPROG_OUTPO
4.7KR30
+3.3V
47KR31
+3.3V
VDDD
VDDD
4.7KR55
4.7KR54
100KR34
100KR35
560pC37
.1uC41
10uC40+3.3V
0RL1
SW_B+
SRD_SND
TP17
10KR9.1u
C12
100pC14
10K1%R11
10K1%R12
10KR10
3
1
2
4
5 6
U5
39pC44
.1uC25
.01uC21
2.2uC20
560pC19
3.3KR24
*R17
TP8
TP18
TP7
TP6
SCK_SND
*C48
PTT_OUT
VDDD
0RR32
*C50
*C49
PTT_OUT
*C52
4001Q1
4001Q2
*Q6
0RR52
SB1D1
SB1D2
SB1D4
SB1D3
560pC11
0RR57
0RR58
47KR36 +3.3V
+3.3V
.1uC43
.1uC42
CS1
SO2
SI5
SCK6
VCC 8
HOLD 7
WP 3
GND 4
AT26DF081AU6
.22uC33
22pC24
*C51
CS7
SO12
SI13
SCK14
DVDD 1
INT29 INT18
GND 2MMA7455L
AVDD 6
GND 5
IADDR0 4
N/C 3
GND 10
GND 11
U10
4.7uC5
4.7uC53
47KR3
47KR4 +3.3V
+3.3V
*R26VDDD
SW +BP2:8
GNDP2:11
VDDDP2:12
PTT_INP2:13
RESETP2:14
MISOP2:15
MOSIP2:16
CLKP2:17
OPT_ENA
P2:18
RDYP2:19
GNDP2:20
RX_OUTP2:23
RX_INP2:25
TX_OUTP2:26
DIS_INP2:27
TX_INP2:28
SB1
D6
*R5
*R25
+3.3V
GND
100pC105
100pC106
100pC107
100pC108
100pC109
100pC113
BL_EN
BL_EN
GND
*
R22 *R23
+3.3V
100pC39
12pC38
CP
CJS2012-05-03 DML
2013-04-04
A-2
1 of 2 7728
MIDIAN ELECTRONICS, INC.DATE:
DESIGN:
DWN BY:
REV:
APPR
COPYRIGHT ©
REV
SHEET PROJECT NUMBER
DOCUMENT NAME
SCHEMATIC2013
VAE-1-MC2
* = NOT INSTALLEDNOTES
PIC101
PIC102COC1
PIC201
PIC202COC2
PIC401
PIC402COC4 PIC501
PIC502COC5
PIC701
PIC702COC7
PIC901 PIC902
COC9
PIC1001
PIC1002COC10
PIC1101 PIC1102
COC11
PIC1201 PIC1202
COC12
PIC1301
PIC1302COC13
PIC1401
PIC1402COC14
PIC1501 PIC1502
COC15
PIC1601 PIC1602
COC16
PIC1701 PIC1702
COC17
PIC1801
PIC1802COC18
PIC1901
PIC1902COC19 PIC2001
PIC2002COC20
PIC2101 PIC2102
COC21
PIC2401
PIC2402COC24
PIC2501 PIC2502
COC25PIC2601
PIC2602COC26PIC2701
PIC2702COC27
PIC2801 PIC2802
COC28
PIC2901 PIC2902
COC29
PIC3001 PIC3002
COC30
PIC3101
PIC3102COC31 PIC3201
PIC3202COC32
PIC3301 PIC3302
COC33
PIC3501 PIC3502
COC35
PIC3601 PIC3602
COC36
PIC3701
PIC3702COC37
PIC3801
PIC3802COC38
PIC3901
PIC3902COC39
PIC4001 PIC4002
COC40
PIC4101 PIC4102
COC41
PIC4201 PIC4202
COC42
PIC4301 PIC4302
COC43
PIC4401
PIC4402COC44
PIC4501
PIC4502COC45
PIC4701 PIC4702
COC47
PIC4801 PIC4802
COC48
PIC4901 PIC4902
COC49
PIC5001 PIC5002
COC50
PIC5101
PIC5102COC51
PIC5201
PIC5202COC52
PIC5301
PIC5302COC53
PIC10501
PIC10502COC105
PIC10601
PIC10602COC106
PIC10701
PIC10702COC107
PIC10801
PIC10802COC108
PIC10901
PIC10902COC109
PIC11301
PIC11302COC113
PID101PID102
COD1
PID201PID202
COD2
PID301PID302
COD3
PID401PID402
COD4
PID601PID602
COD6
PIL101
PIL102
COL1
PIP208COP2:8
PIP2011COP2:11
PIP2012COP2:12
PIP2013COP2:13
PIP2014COP2:14
PIP2015COP2:15
PIP2016COP2:16
PIP2017COP2:17
PIP2018COP2:18
PIP2019COP2:19
PIP2020COP2:20
PIP2023COP2:23
PIP2025COP2:25
PIP2026COP2:26
PIP2027COP2:27
PIP2028COP2:28
PIP301
COP3:1
PIP302
COP3:2
PIP303
COP3:3
PIP304
COP3:4PIP305
COP3:5
PIP306
COP3:6
PIP401 COP4:1
PIP402 COP4:2
PIP403 COP4:3
PIP404 COP4:4
PIP405 COP4:5
PIP406 COP4:6
PIPI01
COPI
PIPO01
COPO
PIQ10DPIQ10G
PIQ10S
COQ1
PIQ20DPIQ20G
PIQ20S
COQ2
PIQ60DPIQ60G
PIQ60S
COQ6
PIR101 PIR102
COR1
PIR201 PIR202
COR2
PIR301 PIR302
COR3
PIR401 PIR402
COR4
PIR501 PIR502
COR5
PIR601 PIR602
COR6
PIR701 PIR702
COR7
PIR801 PIR802
COR8
PIR901 PIR902
COR9 PIR1001 PIR1002
COR10
PIR1101 PIR1102
COR11 PIR1201 PIR1202
COR12
PIR1301
PIR1302
COR13
PIR1401
PIR1402
COR14
PIR1501
PIR1502
COR15PIR1601
PIR1602
COR16
PIR1701 PIR1702
COR17
PIR1801 PIR1802
COR18PIR1901 PIR1902
COR19
PIR2001 PIR2002
COR20
PIR2101 PIR2102
COR21
PIR2201
PIR2202COR22
PIR2301 PIR2302
COR23
PIR2401 PIR2402
COR24
PIR2501 PIR2502
COR25
PIR2601 PIR2602
COR26
PIR2801 PIR2802
COR28
PIR3001
PIR3002
COR30
PIR3101
PIR3102
COR31
PIR3201 PIR3202
COR32
PIR3401 PIR3402
COR34
PIR3501 PIR3502
COR35
PIR3601 PIR3602
COR36
PIR4901 PIR4902
COR49
PIR5001 PIR5002
COR50
PIR5101 PIR5102
COR51
PIR5201 PIR5202
COR52
PIR5401 PIR5402
COR54
PIR5501 PIR5502
COR55
PIR5701 PIR5702
COR57
PIR5801 PIR5802
COR58
COtb0sch1
PITP101
COTP1
PITP201
COTP2
PITP301
COTP3
PITP401
COTP4
PITP501
COTP5
PITP601 COTP6
PITP701
COTP7
PITP801
COTP8
PITP1201
COTP12
PITP1701
COTP17
PITP1801
COTP18
PIU101 PIU102
PIU103
PIU104
PIU105
PIU106
PIU107
PIU108
PIU109
PIU1010
PIU1011
PIU1012PIU1013
PIU1014
PIU1015
PIU1016
PIU1017
PIU1018
PIU1019
PIU1020
PIU1021
PIU1022
PIU1023
PIU1024
PIU1025
PIU1026
PIU1027
PIU1028
PIU1029
PIU1030
PIU1031
PIU1032
PIU1033
PIU1034
PIU1035
PIU1036
PIU1037
PIU1038PIU1039PIU1040
PIU1041
PIU1042
PIU1043
PIU1044
PIU1045
PIU1046
PIU1047
PIU1048
PIU1049
COU1
PIU301
PIU302
PIU303 PIU304
PIU305
PIU306
PIU307
PIU308
PIU309
PIU3010
PIU3011
PIU3012
PIU3013
PIU3014
PIU3015
PIU3016
PIU3017PIU3018
PIU3019
PIU3020
PIU3021
PIU3022
PIU3023
PIU3024
PIU3025
PIU3026
PIU3027
PIU3028
PIU3029
PIU3030
PIU3031PIU3032
PIU3033 PIU3034
PIU3035
PIU3036
PIU3037
PIU3038
PIU3039
PIU3040
PIU3041
PIU3042
PIU3043
PIU3044
PIU3045
PIU3046
PIU3047
PIU3048
COU3
PIU401
PIU402
PIU403
PIU404
PIU405
PIU406
PIU407PIU408
COU4
PIU501
PIU502
PIU503
PIU504
PIU505 PIU506
COU5
PIU601
PIU602
PIU603
PIU604
PIU605
PIU606
PIU607
PIU608
COU6
PIU701
PIU702
PIU703
PIU704
PIU7011
COU7:1
PIU705
PIU706
PIU707COU7:2
PIU708
PIU709
PIU7010
COU7:3
PIU7012
PIU7013
PIU7014
COU7:4
PIU1001
PIU1002
PIU1003
PIU1004
PIU1005
PIU1006
PIU1007
PIU1008
PIU1009
PIU10010
PIU10011
PIU10012
PIU10013
PIU10014
COU10
PIVR101
PIVR102
PIVR103
PIVR104
PIVR105
COVR1
PIVR201
PIVR202
PIVR203
PIVR204
PIVR205
COVR2
PIVR301
PIVR302
PIVR303
PIVR304
PIVR305
COVR3
PIY101
PIY102COY1
PAC101
PAC102COC1
PAC201
PAC202COC2
PAC401
PAC402COC4
PAC501
PAC502COC5
PAC701
PAC702COC7
PAC901
PAC902
COC9
PAC1001PAC1002COC10
PAC1101
PAC1102
COC11
PAC1201PAC1202COC12 PAC1301
PAC1302COC13
PAC1401
PAC1402COC14
PAC1501
PAC1502COC15PAC1601
PAC1602COC16
PAC1701
PAC1702COC17
PAC1801PAC1802COC18
PAC1901 PAC1902COC19
PAC2001 PAC2002COC20
PAC2101
PAC2102COC21
PAC2401
PAC2402COC24
PAC2501
PAC2502COC25
PAC2601
PAC2602COC26
PAC2701
PAC2702COC27
PAC2801PAC2802COC28
PAC2901PAC2902COC29
PAC3001PAC3002COC30
PAC3101PAC3102COC31
PAC3201PAC3202COC32
PAC3301
PAC3302COC33 PAC3501
PAC3502COC35 PAC3601
PAC3602COC36
PAC3701
PAC3702COC37
PAC3801PAC3802COC38 PAC3901PAC3902COC39
PAC4001PAC4002COC40
PAC4101
PAC4102COC41
PAC4201
PAC4202
COC42
PAC4301 PAC4302COC43
PAC4401
PAC4402COC44
PAC4501 PAC4502COC45
PAC4701
PAC4702COC47
PAC4801
PAC4802COC48
PAC4901
PAC4902COC49
PAC5001
PAC5002COC50
PAC5102
PAC5101COC51
PAC5201
PAC5202COC52
PAC5301
PAC5302COC53
PAC10101 PAC10102COC101
PAC10201 PAC10202COC102
PAC10301 PAC10302COC103
PAC10401 PAC10402COC104
PAC10501 PAC10502COC105
PAC10601 PAC10602COC106
PAC10701 PAC10702COC107
PAC10801 PAC10802COC108
PAC10901 PAC10902COC109
PAC11001 PAC11002COC110
PAC11101 PAC11102COC111
PAC11201 PAC11202COC112
PAC11301 PAC11302COC113
PAD101PAD102COD1
PAD201PAD202COD2
PAD301PAD302COD3
PAD401PAD402COD4
PAD601PAD602COD6
PAL101 PAL102COL1
PAP1010 PAP1011PAP109PAP108PAP107 PAP106PAP105PAP104PAP103PAP102PAP101
COP1
PAP2030
PAP2029PAP201PAP202PAP203PAP204PAP205PAP206PAP207PAP208PAP209PAP2010PAP2011PAP2012PAP2013PAP2014PAP2015PAP2016PAP2017PAP2018PAP2019PAP2020PAP2021PAP2022PAP2023PAP2024PAP2025PAP2026PAP2027PAP2028
COP2
PAP301PAP302
PAP305
PAP303
PAP306
PAP304COP3
PAP401
PAP402
PAP405
PAP403
PAP406
PAP404COP4
PAPI01COPI PAPO01COPOPAQ10G
PAQ10DPAQ10S
COQ1
PAQ20GPAQ20D
PAQ20SCOQ2
PAQ60GPAQ60D
PAQ60SCOQ6
PAR101
PAR102COR1
PAR201
PAR202COR2
PAR301PAR302COR3
PAR401PAR402COR4
PAR501
PAR502COR5
PAR601
PAR602
COR6 PAR701
PAR702
COR7
PAR801
PAR802
COR8
PAR901
PAR902
COR9PAR1001
PAR1002COR10
PAR1101
PAR1102COR11
PAR1201PAR1202COR12
PAR1301PAR1302COR13
PAR1401
PAR1402COR14
PAR1501 PAR1502COR15
PAR1601
PAR1602COR16
PAR1701 PAR1702COR17
PAR1801
PAR1802COR18
PAR1901PAR1902COR19
PAR2001 PAR2002COR20
PAR2101
PAR2102COR21
PAR2201
PAR2202COR22
PAR2301
PAR2302COR23
PAR2401 PAR2402COR24
PAR2501
PAR2502COR25
PAR2601
PAR2602COR26
PAR2801 PAR2802COR28
PAR3001PAR3002COR30 PAR3101 PAR3102COR31
PAR3201 PAR3202COR32
PAR3401
PAR3402COR34
PAR3501
PAR3502COR35
PAR3601
PAR3602COR36
PAR4901
PAR4902COR49PAR5001
PAR5002COR50PAR5101
PAR5102COR51
PAR5201 PAR5202COR52
PAR5401
PAR5402COR54
PAR5501 PAR5502COR55
PAR5701
PAR5702COR57
PAR5801
PAR5802COR58
PAR10101
PAR10102COR101PAR10201
PAR10202COR102
PAR10301
PAR10302COR103PAR10401
PAR10402COR104
PAR10501
PAR10502COR105PAR10601
PAR10602COR106
PAR10701
PAR10702COR107 PAR10801
PAR10802COR108
PAR10901
PAR10902COR109 PAR11001
PAR11002COR110
PAR11101PAR11102COR111
PAR11201PAR11202COR112
PAR11301PAR11302COR113
PAR11401PAR11402COR114
PAR11501PAR11502COR115
COtb0sch2
PATP101 COTP1PATP201COTP2
PATP301COTP3
PATP401COTP4
PATP501COTP5PATP601COTP6
PATP701COTP7PATP801COTP8
PATP1201COTP12
PATP1701
COTP17
PATP1801COTP18
PAU1049PAU101PAU102PAU103PAU104PAU105PAU106PAU107PAU108PAU109PAU1010PAU1011PAU1012
PAU1013PAU1014PAU1015PAU1016PAU1017PAU1018PAU1019PAU1020 PAU1021PAU1022PAU1023 PAU1024PAU1025PAU1026PAU1027PAU1028PAU1029PAU1030PAU1031PAU1032PAU1033PAU1034PAU1035PAU1036
PAU1037PAU1038PAU1039PAU1040PAU1041PAU1042PAU1043PAU1044PAU1045PAU1046PAU1047PAU1048
COU1
PAU301PAU302PAU303PAU304PAU305PAU306PAU307PAU308PAU309PAU3010PAU3011PAU3012PAU3013PAU3014PAU3015PAU3016PAU3017PAU3018PAU3019
PAU3020PAU3021PAU3022
PAU3023PAU3024
PAU3025PAU3026PAU3027 PAU3028PAU3029PAU3030 PAU3031PAU3032PAU3033 PAU3034PAU3035PAU3036PAU3037PAU3038PAU3039PAU3040PAU3041PAU3042PAU3043PAU3044PAU3045PAU3046PAU3047PAU3048
COU3
PAU408PAU407PAU406PAU405 PAU404
PAU403PAU402PAU401
COU4
PAU501PAU502PAU503 PAU504
PAU505PAU506
COU5
PAU601PAU602PAU603PAU604
PAU605 PAU606 PAU607 PAU608
COU6
PAU701PAU702PAU703PAU704PAU705PAU706PAU707PAU708
PAU709PAU7010PAU7011PAU7012PAU7013PAU7014
COU7
PAU10014 PAU10013PAU10012
PAU10011PAU10010PAU1009PAU1008PAU1007PAU1006
PAU1005PAU1004PAU1003PAU1002PAU1001
COU10
PAVO1010 PAVO1011PAVO109 PAVO108 PAVO107 PAVO106 PAVO105 PAVO104 PAVO103 PAVO102 PAVO101
PAVO1030
PAVO1029
PAVO1012
PAVO1013
PAVO1014
PAVO1015
PAVO1016
PAVO1017
PAVO1018
PAVO1019
PAVO1020
PAVO1021
PAVO1022
PAVO1023
PAVO1024
PAVO1025
PAVO1026
PAVO1027
PAVO1028
PAVO10GPAVO10D
PAVO10S
PAVO1031
PAVO1032
PAVO1033
PAVO1034
PAVO1035
PAVO1036
PAVO1037PAVO1038PAVO1039PAVO1040PAVO1041PAVO1042PAVO1043PAVO1044PAVO1045PAVO1046PAVO1047PAVO1048
PAVO1049
PAVO100
COVO1
COVO5
PAVR103 PAVR101
PAVR104
PAVR102
PAVR105
COVR1PAVR203 PAVR201
PAVR204
PAVR202
PAVR205
COVR2PAVR303 PAVR301
PAVR304
PAVR302
PAVR305
COVR3
PAY102PAY101COY1
PAD10102
PAD10101COD101
PAD10202
PAD10201 COD102
PAD10302
PAD10301 COD103PAD10402
PAD10401 COD104
PAD10502
PAD10501COD105
PAD10602
PAD10601COD106
PAD10802
PAD10801COD108
PAD10902
PAD10901COD109
PASW003
PASW002
PASW001
COSW0
PASW103
PASW102
PASW101
COSW1
PASW203
PASW202
PASW201
COSW2
PASW303
PASW302
PASW301
COSW3
PASW403
PASW402
PASW401
COSW4
PASW503
PASW502
PASW501
COSW5
PASW603
PASW602
PASW601
COSW6
PASW703PASW702PASW701
COSW7
PASW803
PASW802
PASW801
COSW8
PASW903
PASW902
PASW901
COSW9
PASW#03
PASW#02
PASW#01
COSW#
PASW003
PASW002
PASW001
PASWDN03
PASWDN02
PASWDN01
COSWDN
PASWP103 PASWP102
PASWP101 COSWP1
PASWP203
PASWP202
PASWP201
COSWP2
PASWUP03
PASWUP02
PASWUP01
COSWUP
COtb0sch1
PAVO2049
PAVO201PAVO200
PAVO202
PAVO205
PAVO206
PAVO203
COVO2