v.1.0 - Tam Hop - Workmate claris (E).pdfThe Corporate Village Da Vincilaan 11 Box F1 1935 Zaventem...

1

WorkMate™ Claris™ System INSTRUCTIONS FOR USE

INTERNATIONAL EDITION

ARTEN100108827 C (2015-07)

Copyright 2015t. Jude Medicalll rights reserved.

nless otherwise noted, ™ indicates that the name is a ademark of, or licensed to, St. Jude Medical or one of its bsidiaries. ST. JUDE MEDICAL and the nine-squares mbol are trademarks and services marks of St. Jude Medical, c. and its related companies.

v.1.0.1

©SA

UtrsusyIn

St. Jude MedicalOne St. Jude Medical DriveSt. Paul, MN 55117-9913USA+1 855 478 5833+1 651 756 5833sjm.com

St. Jude MedicalCoordination Center BVBAThe Corporate VillageDa Vincilaan 11 Box F11935 Zaventem Belgium+32 2 774 68 11sjm.com

Australian Sponsor:St. Jude Medical Australia Pty Limited17 Orion RdLane Cove N SW 2066AUSTRALIA+61 (02) 9936 1200

EC REP

2 WorkMate™ Claris™ System Rev C 100058538-en

General

Symbol Description

Type CF applied part

Defibrillation-proof type CF applied part

Defibrillator-proof type BF applied part

US Federal law restricts this device to sale by or on the order of a physician.

Do not reuse

Fragile

Keep dry

Date of Manufacture

Manufacturer

Use by date

Lot number

Catalog number

Serial number

Separate collection of waste at end of life as required by European Directives. Dispose of in accordance with the applicable country regulation.

Caution

Warning

Notified body CE Mark

Authorized representative in the European community

Consult Instructions for Use

On (power: connection from the mains)

Off (power: disconnection from the mains)

Alternating Current

Fuse

Phone

Facsimile

Do Not Use If Package Is Damaged

Finish Goods Number

Temperature Limitation

Relative Humidity

General

Symbol Description

EC REP

3WorkMate™ Claris™ S ystem Rev C 100058538-en

Do not connect to the Patient

Package Contains 1 Items

Non Sterile

This Way Up

Potential Equalization Conductor (symbol is located on the terminal itself

Review Software

Includes:

Ready for Transport

Software Version

Integration Engine

Software Upgrade Kit

Follow instructions for use

RecordConnect

Invasive Blood Pressure (IBP) Cable

SDU Cable

GSU Cable

General

Symbol Description

Electrocardiogram Cable

System

Intertek Safety Agency Certification Mark

Compatible with St. Jude Medical™ Electrophysiology Products

TUV Safety Agency CertificationMark

2 Port KVM Switch

Amplifier

Bed Bracket Assembly

2 Port DVI Monitor Splitter

Bed Rail Kit

Cable Kit. 10 m

Cable Kit, 15 m

Cable Kit, 30 m

Cable, Coax, 1 ft

Cable, Fiber Crossover 10m

Cable, Fiber, 10m

Cable, Fiber, 30m

Cable, Serial, 3 ft

Cardiac Stimulator

General

Symbol Description


Cardiac Stimulator Cable

Display Plus Amplifier

DisplayPort Adapter

DMS59 to Dual DVI

ECG Cable Set, Radiolucent

ECG Cable Set, Radiopaque

ECG International Cable Assy

ECG Leadset

ECG Radiotranslucent Leadset

Equipotential Cable

Ferrite, 18mm

Ferrite, 9.85mm

For Use With

Generic Stimulator Cable

HDMI Adapter

IFU, Software v.1.0

Mouse

Keyboard

Media Conv, DB9 Female

Media Conv, DB9 Male

Monitor 23”

Monitor Cable Kit

General

Symbol Description

Monitor Mount Rotational Stop

Monitor Stand Kit

Monitor

Power Conditioner 1440 VA




Power Cord

Power Kit, 110

Power Kit, 220

Power Strip 4

Power Strip 6

Power Strip 8

Power Supply Adapter

Power Supply

Power Supply, 12V

Printer

Review Module - 10 License

Stimulator, 4 Channel

System - Display Plus

Touch Screen Stand

USB2DVI USB Framegrabber

General

Symbol Description


DVI Cable

S-Video to VGA Signal Converter Unit

Software Upgrade

Software Installation

Refer to instruction manual/booklet

WorkMate™ Claris™ System Display Workstation

Symbol Description

RF Generator connection

Stimulator connection

Software Version

Amplifier Network Connection

DATA Network Connection

Display Workstation

Hospital Network Connection

RF Filter

Indicates connector location

General

Symbol Description

Amplifier

Symbol Description

Right Leg Connection

Stimulator connection

Catheter Interface Module cable connection for catheter inputs 1-56; RecordConnect Catheter Inputs 1-56

Catheter Interface Module cable connection for catheter inputs 57-120; RecordConnect Catheter Inputs 57-120

Analog cable input connection

Analog cable output connection

Pace Detection cable connection

Synchronization Output cable connection

ECG or Record Connect ECG Cable Connector

Fiber Optic Cable

Internal Blood Pressure


Catheter Interface Modules (CI Module)

Symbol Description

56 Pin Catheter Interface Module

64 Pin Catheter Interface Module

Reference socket connector

Amplifier

WorkMate™ Claris™ RecordConnect

Symbol Description

RecordConnect

ECG cable connector

WorkMate™ Scribe™ Module

Symbol Description

Display Workstation

Module

Amplifier Network Connection

DATA Network Connection

PHYSIO Connection

Dual Monitor Mount


WorkMate™ ImageSync™ Module

Symbol Description

Module

WorkMate™ Unity™ Review Module

Symbol Description

HL7 Module

Review Module - Single License

Review Module - Site License

Review Module

DICOM Module


Table 1.Definitions, Acronyms, and Abbreviations

ATM Activation Timing Map

DPST Double Pole Single Throw

EP Electrophysiology

DWS Display Workstation

OS Operating System

CI Module Catheter Input Module

TSM Philips Touch Screen Module

A/D Analog to Digital Converter

D/A Digital to Analog Converter

Select To click the left mouse button once while the mouse pointer is pointing to a selectable item.

FFT Fast Fourier Transform

RF Radiofrequency

CMRR Common Mode Rejection Ratio

CathMap Catheter map

LAT Local Activation Time

9WorkMate™ Claris™ System Rev C 100058538-en

Introduction

The WorkMate™ Claris™ System is a fully computerized system for capturing and measuring physiological data in the clinical electrophysiology (EP) laboratory. It provides digital signal acquisition and display of those electrical signals on high resolution monitors.

An EP system is used to monitor and analyze surface ECGs and intracardiac signals. Catheters are guided into the heart and intracardiac electrical signals are acquired from the electrodes on the indwelling catheters from various heart locations. These signals are then used to measure cardiac electrical activity via a catheter to the heart. A cardiac stimulator is used to send an electrical pulse via a catheter to the heart. These electrical pulses are called pacing protocols. Pacing protocols, for example, may be performed in order to reproduce any life threatening arrhythmias under the safest possible conditions for the patient. Treatment of an arrhythmia may then be initiated with ablation therapy, drug therapy, or placement of cardiac devices that will control the heart's rhythm.

The system is also intended for recording electrocardiograms from multiple sites during clinical assessment of electrophysiological interventions. The WorkMate™ Claris™ System provides online measurements of intra-channel intervals, and presents these measurements on the display monitor. Retrieval and display are provided without interruption of the multi-channel acquisition process. A DVD disk drive is available for archival storage of digitized data.

Menu-driven software is incorporated for patient signal analysis and data. The WorkMate™ Claris™ System has an integrated patient database system for rapid access to all patient records. Unique features of the system include:

■ Online interval measurement

■ Four-channel integrated stimulator

■ A choice of scrolling or wiper-mode display during Real Time signal acquisition

■ A comprehensive database with a query function

■ User configurable report template

Indications for Use

The WorkMate™ Claris™ System is indicated for use during clinical electrophysiology procedures.

Contraindications

There are no known contraindications to the use of the WorkMate™ Claris™ System.


System Description

The WorkMate™ Claris™ System is a computer-based electrocardiographic recording and monitoring system designed for efficient capture, display, and retrieval of surface and intracardiac signals during cardiac EP studies. The system contains a fully automated software waveform detector (trigger), which performs on-line recognition of cardiac activation on pre-selected leads. Temporal interval measurements are computed on a beat-by-beat basis on multiple channels and dynamically posted on the Real Time display. Intervals are calculated between waveforms from the same source on a specific channel (intra-channel measurements) and from multi-source signals across two or more channels (inter-channel measurements).

All trigger locations with notes or annotations, as well as interval measurements, are stored concurrently with the digitized signals. The following intervals and measurement are presented on the display monitor as they occur:

■ Atrial-to-atrial (A-A)

■ Ventricular-to-Ventricular (V-V)

■ Surface QRS-to-QRS (R-R)

■ Ventricular-to-Atrial (V-A)

■ Pacing Stimulus (Stim)

■ Pressure (Pres)

Continuous capture of the digitized signals can be invoked for any portion of the study protocol, or for the entire study. Retrieval of earlier passages of the current study, or an earlier study of the same patient, can be enabled on a secondary monitor without interruption of the Real Time display. Review by protocol or by time of event can be performed by use of user interface buttons and hot keys. Editing of computer-generated trigger markers can be done under operator control in the Review mode. Archival storage of edited patient records is provided on various archive media.


Figure 1 is a picture of the WorkMate™ Claris™ System cart and its components.

1. Remote Monitors (Review and Real Time)

2. Amplifier (120 channel pictured)

3. EP-4™ Cardiac Stimulator

4. Printer

5. Isolation Transformer

6. WorkMate™ Claris™ Display Workstation (DWS)

7. Keyboard

8. EP-4™ Touch Screen

9. Real Time Monitors

Figure 1. The WorkMate™ Claris™ Cart and Components

WARNING: The cart pictured in Figure 1 is mounted on wheels and is mobile. During operation it is important to set the front wheel locks to prevent unexpected movement. Failure to do so could result in possible damage to the equipment and/or disruption of desired operation.

NOTE: The cart in Figure 1 is mounted on wheels and is mobile. During transport it is important to retract monitors so they are centered above cart (Figure 2 and Figure 3).

1

2

3

4 5 6

7

8

9

5


Figure 2. Safe transport position

Figure 3. Unsafe—Tip Hazard

Figure 4 is a block diagram of most EP recording systems in use today. The cardiac signals are monitored by viewing a Real Time monitor, and are analyzed by viewing and measuring these signals on the Review monitor. The cardiac signals are captured and conditioned with a Amplifier, and then stored by the computer. The stimulator sends electrical impulses to indwelling catheters through the Amplifier. The computer then sends the signals to the monitors and stores these signals for future retrieval. Significant events and user notes are also stored for each EP procedure. EP summary reports and electrograms can be printed as desired.


Figure 4. Basic EP Lab Connection

WARNING: The components in the WorkMate™ Claris™ System must be supplied power from an isolation transformer for use in the Patient Environment to reduce leakage currents to safe levels.The amplifier and the EP-4™ Cardiac Stimulator may be plugged directly into the mains power.

System Components

The WorkMate™ Claris™ System includes the following features and components:

ClearWave™ Technology

The ClearWave™ Technology's 32-bit processing and increased sample rate allows increased dynamic range of signals. This dynamic range increase allows greater resolution of signals, providing dramatic clarity. It also retains all the flexibility and control offered with the unipolar signal capture.

ClearWave™ Technology provides the highest signal resolution available for an EP Recording System. View complex, smaller, fractioned signals more clearly via the Increased Amplitude Resolution and Sample Rate. The ActiveNotch™ System cleanly filters line noise without compromising critical electrograms.

The time from a pacing pulse to the recovery of the signal is important in pacing/mapping situations. ClearWave™ Technology also dramatically reduces this post pacing interval.


WorkMate™ Scribe™ Module

The WorkMate™ Scribe™ Module product is an optional integrated monitoring and review station for the WorkMate™ Claris™ System that allows a separate user to review and edit current patient study data stored on the WorkMate™ Claris™ System and monitor patient data from the WorkMate™ Claris™ System during the patient study.

Most of this Instructions for Use (IFU) covers functions and features that are common to both the WorkMate™ Claris™ System and WorkMate™ Scribe™ Module.

Refer to Chapter 10 for the instructions for use of the WorkMate™ Scribe™ Module.

EnSite™ Derexi™ Module

The EnSite™ Derexi™ Module product is a software extension to the WorkMate™ Claris™ System Mapping Window and an electronic interconnection between the WorkMate™ Claris™ System computer and the EnSite™ Velocity™ System. EnSite™ Derexi™ Module synchronizes the Mapping Window signals and the procedure log to the EnSite™ Velocity™ stored map points.

NOTE: The WorkMate™ Claris™ System is not compatible with the EnSite™ System prior to the EnSite™ Velocity™ System.

Refer to Chapter 11 in this IFU for information on the functions and features of the Mapping Window.

Refer to Chapter 12 for information on the EnSite™ Derexi™ Module.

WorkMate™ ImageSync™ Module

The WorkMate™ ImageSync™ Module is a supplementary component to the WorkMate™ Claris™ System, which connects to other systems and records images or movies into the WorkMate™ Claris™ System database, case, and patient record. Image systems (video sources) are logged in the procedure log. This module identifies and retrieves images side by side with the signals with this module.

Refer to Chapter 4 on page 72 for information on the functions and features of the Imaging Window.

Patient Connections

The patient is connected to the WorkMate™ Claris™ System through a surface ECG cable, catheters, and pressure transducer(s). These are plugged into the WorkMate™ Claris™ Amplifier and the CI Module. These inputs are electrically isolated from earth ground. The pacing outputs of the stimulator are electrically isolated and are plugged into the Amplifier.

Non-isolated Connections

WARNING: The stimulator back panel connectors and Amplifier back panel BNC connectors are NOT isolated. Never connect them directly to a patient. Always plug external devices into an isolation transformer.

Non-isolated analog signals from other devices may be displayed using the non-isolated channels on the backside of the Amplifier

NOTE: Special attention must be given to proper grounding and electrical safety. Even small chassis leakage currents passing through the heart can induce fibrillation. Never connect non-isolated inputs or outputs directly to a patient. A functioning defibrillator should always be available.

NOTE: Special attention must be given to all equipment connected to the patient. All equipment capable introducing a DC voltage level offset or introducing 50/60 cycle noise should be plugged into and share a common earth ground circuit. These devices include other recording systems, stimulators, defibrillators, and RF generators.


Graphical User Interface

The WorkMate™ Claris™ System consists of two, independent high resolution screens as well as a keyboard and a mouse for control of data acquisition, storage, and retrieval of electrophysiological signals. The main monitor is dedicated to Real Time visualization of signals. Signals that can be accommodated are typically surface ECG, intracardiac signals, stimulation markers, and output of blood pressure transducers. Automated wave form recognition and interval measurement are available for any of the electrocardiographic signals. The page number is also displayed.

The secondary monitor is used as a menu-driven Review console for display and retrieval of data from either the current study or a previous study contained in the patient database.

The presentation of menus provides for selection and control of system features. These features may be either mouse or keyboard activated and include such options as:

■ Catheter or lead identification

■ Choice of location, size, and color of the signal display

■ Selection of signals to be automatically analyzed

■ Entry of customized study protocols

■ Enabling or disabling permanent storage of signals

■ Measurement storage with the case study

The Review monitor serves as the display medium for previously recorded data. In the Review monitor, any portion of the recorded file can be accessed by event marker, time of event, or by scrolling through in a continuous or page-by-page mode. Other options available in the Review monitor are

■ Holter window,

■ Post acquisition filtering,

■ Automatic analysis

Warnings, Cautions, and Disclaimers

The detection algorithms used by the WorkMate™ Claris™ System contain a sophisticated software trigger for electrocardiograms. The accuracy of trigger placement and interval measurement cannot be guaranteed, particularly in the case of poor signal quality. Therefore, verification of trigger locations and associated measurements is required on the part of the user before full confidence can be placed in reports produced by automated analysis.

The equipment is intended for use by qualified medical personnel and only after they have been trained in the proper use of this equipment.

This system should be used by or under the supervision of physicians thoroughly trained in techniques of intracardiac electrophysiology.

The IFU is recyclable. Dispose of all packaging materials as appropriate.

St. Jude Medical, Inc. does NOT assume responsibility for damage to the equipment caused by improper ventilation, improper or faulty power, or improper monitor booms.

For continued safety, it is necessary that the instructions listed in this IFU are followed. It is important that instructions in this IFU in no way supersede established medical procedures concerning patient care.

Federal law restricts this device to sale by or on the order of a physician.


The following is a list of warnings and cautions that appear in this IFU or that may appear as labeling on the WorkMate™ Claris™ System or WorkMate™ Scribe™ Module:

WARNING: The WorkMate™ Claris™ System components are not suitable for use within Oxygen Rich Environments or in the presence of flammable gases, including flammable anesthetic mixtures with air or with oxygen or with nitrous oxide.

WARNING: The WorkMate™ Claris™ System should not be used adjacent to or stacked with other equipment.

The Amplifier has been tested in a stacked or adjacent configuration with the EP-4™ Cardiac Stimulator, and this is the only stacked or adjacent use that is permitted.

WARNING: The use of the WorkMate™ Claris™ System accessories, transducers and cables, with any other Medical Electrical equipment or Medical Electrical system, may result in increased emissions or decreased immunity of that equipment or system.

WARNING: Installing un-approved software or operating system on the WorkMate™ Scribe™ Module or WorkMate™ Claris™ hard drive may severely affect system performance and device safety.

WARNING: Service by Qualified Personnel Only.

WARNING: Do not utilize or add any extension cords with the system. The isolation transformer supplied with the system and any multiple socket outlet used on the system must not be positioned on or near the floor. These multiple socket outlets shall not be placed on the floor.

WARNING: Do not handle power line connections while in contact with the patient.

WARNING: The rate, cycle length, ECG, and pressure displays are not to be used as the primary/sole patient monitor during an Electrophysiology study. These subsystems contain no alarms for indicating inoperative conditions.

WARNING: Prior to using the WorkMate™ Claris™ or WorkMate™ Scribe™ Module system, read any and all supplied instructions and Technical Bulletins that describe known system limitations.

WARNING: Consult the IFU for the optional Smiths Medical Advisor™ Vital Signs Monitor for all operating instructions, warnings and cautions specific to that device.

WARNING: Prior to using the WorkMate™ Claris™ System, WorkMate™ Scribe™ Module, or the Derexi™ Module, be sure all system components are safely secured to the cart or other operating surface where the system installed. Falling components can cause injury to the operator or patient.

WARNING: Do not allow liquid to enter the case or submerge any part of the WorkMate™ Claris™ System, WorkMate™ Scribe™ Module, or any accessories used with the system. Fluid spilled in the WorkMate™ Claris™ System, WorkMate™ Scribe™ Module, or accessory electronic components could cause the unit to malfunction or present a hazard that could result in patient or operator injury. Unplug the AC power cord from this equipment before cleaning or disinfecting. If any liquid enters the case of any item while the system is in use, unplug the power cable immediately. Only use dry hands when unplugging the power cable. Remove the unit from service and contact St. Jude Medical, Inc.

CAUTION: DO NOT touch any connector to avoid electric shock.

WARNING: If the connectors are forcefully connected the pins in the connector can be bent or broken. If this happens the cable must be destroyed to prevent its use.

WARNING: The cart is mounted on wheels and is mobile. During operation it is important to set the front wheel locks to prevent unexpected movement. Failure to do so could result in possible damage to the equipment and/or disruption of desired operation.

WARNING: Exit the system via the menu-driven selections for shutdown before turning the power OFF. Simply turning off the system or a power failure while running the system could cause loss of data.

WARNING: This product is not intended as a life sustaining device. Rescue equipment must be available at all times during the EP procedure.


WARNING: The Maximum Total Output Power of the main cart isolation transformer and the multi-socket power strips is limited to 1440 VA. The Maximum Total Output Power of the bedside cart isolation transformer and its multi-socket power strips is limited to 500 VA. Do not connect additional equipment to power strips supplied with the transformer. Failure to do so could result in system failure or damage.

WARNING: Do not modify or make any additional connections to the WorkMate™ Claris™ System, other than those described in this manual.

WARNING: Do not connect items of the WorkMate™ Claris™ System that are required to be plugged into an isolation transformer directly to a wall supply power outlet. Plugging these items directly into the power outlet supply can cause excessive patient leakage currents.

WARNING: The multi-socket power strips supplied with the system should only be connected to the isolation transformer supplied with the system.

WARNING: The system may serve for clinical use only after it has been fully tested and approved according to standard St. Jude Medical procedures.

WARNING: The WorkMate™ Claris™ System and its peripherals/accessories comply with IEC 60601-1-2 for EMI/EMC. However, since it processes and displays low level patient signals, other radiating devices may interfere.

WARNING: When connecting the WorkMate™ Claris™ System or components to any other device or system, verify proper operation before clinical use.

WARNING: Accessory equipment connected to the analog and digital interfaces must comply with the respective IEC standards (IEC 60950 for data-processing equipment and IEC 60601-1 for medical equipment). Additional equipment connected to the signal input or output connections comprise a medical system and therefore, must comply with the requirements of IEC 60601-1-1 or Clause 16 of IEC 60601-1 3rd Edition.

WARNING: Interconnecting cables are subject to abuse if laid on the floor. Precautions must be taken to dress cabling to prevent damage.

WARNING: Use only St. Jude Medical approved accessories, cables and peripherals. Use of non-approved accessories can degrade the system performance and compliance to safety, emissions and immunity standards.

CAUTION: This device and accessories should be recycled according to local and national laws after useful life.

WARNING: To avoid electrical safety hazard, check grounding reliability periodically.

WARNING: The WorkMate™ Claris™ System must be installed and set up by authorized St. Jude Medical personnel only.

WARNING: Service must be provided by qualified St. Jude Medical (SJM) Personnel only. SJM shall be released from all obligations under its warranty if repairs or modifications are made to the Product by persons other than SJM's service personnel.

WARNING: Do not connect Multiple Socket-Outlets (MSO’s) or extension cords to the system.

WARNING: To avoid the risk of electric shock, this equipment must only be connected to a supply mains with protective earth.

WARNING: The potential equalization conductor can be connected to that of other equipment when necessary, to make sure that all these devices are connected to the potential equalization bus bar of the electrical installation.

WARNING: The Stimulus Accessory cable connectors numbered 1 through 4 (including 4-dot symbols) must be connected to the EP-4™ Cardiac Stimulator connectors labeled with the same 4-dot symbols, to prevent incorrect output of the stimulus signals.

WARNING: Only defibrillation-proof stimulators shall be connected to the amplifier when using the generic stimulator cable.

WARNING: The stimulator back panel connectors and Amplifier back panel BNC connectors are NOT isolated. Never connect them directly to a patient. Always plug external devices into an isolation transformer.


CAUTION: The power cord for each isolation transformer in the WorkMate™ Claris™ System is the main disconnect for the patient environment area equipment and the non-patient environment equipment. To disconnect the mains power, unplug the power cord to each isolation transformer. The system components should be positioned such that access to the power cord connection is unobstructed.

Power Off the WorkMate™ Claris™ System

Exit the software to the main menu using the user interface navigation techniques presented in the following steps.

1. Power off all EP-4™ Cardiac Stimulator stim channels and the power switch on the front of the unit.

2. Power off the Amplifier, using the rocker switch on the front of the unit

3. On the WorkMate™ Claris™ System click [Exit].

4. Answer prompt.

5. If studies are available for archive, initiate the archive sequence (optional). If the system is configured to prompt archiving upon case exit, a DVD must be inserted into the DVD drive prior to exiting. If not, the system will not recognize the DVD.

6. Select [Shutdown] on the WorkMate™ Claris™ System. If prompted to shutdown the EP-4™ Touch Screen, click [Yes]. TheWorkMate™ Claris™ System DWS and the EP-4™ Touch Screen will power off automatically.

If you are not prompted to shut down the EP-4™ Touch Screen, select [Shutdown] on the EP-4™ Touch Screen and it will power down automatically.

WARNING: Exit the system via the menu-driven selections for shutdown before turning the power OFF. Advanced buffering techniques are used for both the database and Real Time acquisition. Simply turning off the system or a power failure while running the system could cause loss of data.

IEC 60601-1 Classifications

Amplifier Classifications:

■ Protection against electric shock: Class I

■ Applied Parts Classification: CF

■ Ingress Classification: IPX1

■ Method of Sterilization: Non-sterile

■ Not classified for use in an Oxygen Rich Environment

■ Mode of Operation: Continuous Operation

v.1.0 - Tam Hop - Workmate claris (E).pdfThe Corporate Village Da Vincilaan 11 Box F1 1935 Zaventem...

Documents

Transcript of v.1.0 - Tam Hop - Workmate claris (E).pdfThe Corporate Village Da Vincilaan 11 Box F1 1935 Zaventem...