Utility Knife Wire Stripper Flat Blade · no stray copper strands. STEP 11 13A BS1363 Plug Top Fit...
109
www.AAVPQ.com 13A BS1363 Plug Top TOOLS Cable Cutter Flat Blade Screwdriver Utility Knife Side Cutters Wire Stripper
Transcript of Utility Knife Wire Stripper Flat Blade · no stray copper strands. STEP 11 13A BS1363 Plug Top Fit...
www.AAVPQ.com
13A BS1363 Plug TopTOOLS
Cable CutterFlat BladeScrewdriver
Utility Knife
Side Cutters
Wire Stripper
www.AAVPQ.com
13A BS1363 Plug TopSTEP 1
www.AAVPQ.com
13A BS1363 Plug TopSTEP 2
Measure the Length of Cable Jacket to strip
www.AAVPQ.com
13A BS1363 Plug TopSTEP 3
Strip the Cable Jacket
Do not cut all the way thru the jacket
www.AAVPQ.com
13A BS1363 Plug TopSTEP 4
Bend the Cable Jacket
Ensure the insulation of each wire has not been nicked or cut
www.AAVPQ.com
13A BS1363 Plug TopSTEP 5
Bend the Cable Jacket
Ensure the insulation of each wire has not been nicked or cut
www.AAVPQ.com
13A BS1363 Plug TopSTEP 6
1cm past the terminal
Cut the wires to length.
www.AAVPQ.com
13A BS1363 Plug TopSTEP 7
The Brown Wire should be shorter
Cut the wires to length.
www.AAVPQ.com
13A BS1363 Plug TopSTEP 8
Strip the wires
Strip 1cm of the insulation
www.AAVPQ.com
13A BS1363 Plug TopSTEP 9
Twist the copper conductor
Fold the conductor double
www.AAVPQ.com
13A BS1363 Plug TopSTEP 10
Tighten the screws for each terminal
Ensure that there are no stray copper strands
www.AAVPQ.com
13A BS1363 Plug TopSTEP 11
Fit the Correct Fuse
3A - up to 700 Watts5A - up to 1200 Watts13A - up to 3000 Watts
www.AAVPQ.com
13A BS1363 Plug TopSTEP 12
Fit the Cover
Ensure that wires arenot crushed or trapped by the cover
TOOLS
Cable Cutter
Cable Stripper
Solder Station
Side Cutters
Wire Stripper
XLR 3 Assembly
HeatGun
www.AAVPQ.com
Order of Assembly
XLR 3 Assembly
BOOT CHUCK INSERT HOUSING
www.AAVPQ.com
Slide the Boot onto the cable
XLR 3 AssemblySTEP 1
www.AAVPQ.com
Prepare Cable as shown
XLR 3 AssemblySTEP 2
XLR 3 AssemblySTEP 3
Insert wires into the terminals and solder them
www.AAVPQ.com
XLR 3 AssemblySTEP 3
Pin 1 - Gnd
Pin 2 - + Red
Pin 3 - – Black
www.AAVPQ.com
View – REAR MALE
www.AAVPQ.com
XLR 3 AssemblySTEP 4
Put Chuck onto the cable.Pay Attention to the guiding key
www.AAVPQ.com
XLR 3 AssemblySTEP 5
Slide INSERT & CHUCK together into the HOUSING.
XLR 3 AssemblySTEP 6
Finish installation by turning the BOOTonto the connector
www.AAVPQ.com
TOOLS
Cable Cutter
Cable Stripper
Solder Station
Side Cutters
Wire Stripper
RCA Phono Assembly
HeatGun
www.AAVPQ.com
Slide the Boot onto the cable
RCA Phono AssemblySTEP 1
www.AAVPQ.com
Prepare Cable as shown
STEP 2 RCA Phono Assembly
www.AAVPQ.com
Solder the Wire Ends
STEP 3 RCA Phono Assembly
www.AAVPQ.com
STEP 4 RCA Phono Assembly
❶ Position the CHUCK onto the cable ❷ Align chuck with plugfinger
www.AAVPQ.com
STEP 5 RCA Phono Assembly
Slide the HOUSING onto the
Plugfinger with Chuck
If using a cable with big O.D. break off marked part on the Chuck
www.AAVPQ.com
STEP 6 RCA Phono Assembly
Finish the installation by tightening the bushing onto the connector
Long NosePlier
TOOLS
Cable Cutter
Cable Stripper
Solder Station
Side Cutters
Wire Stripper
HeatGun
6.3mm TRS Phone Jack Assembly
www.AAVPQ.com
Slide the Boot onto the cable
6.3mm TRS Phone Jack AssemblySTEP 1
www.AAVPQ.com
6.3mm TRS Phone Jack AssemblySTEP 2
Prepare Cable as shown
www.AAVPQ.com
6.3mm TRS Phone Jack AssemblySTEP 3
Solder the Wire Ends
www.AAVPQ.com
6.3mm TRS Phone Jack AssemblySTEP 4
❶ Position the CHUCK onto the cable ❷ Align chuck with Plugfinger
www.AAVPQ.com
6.3mm TRS Phone Jack AssemblySTEP 5
Slide the HOUSING onto the
Plugfinger with Chuck
If using a cable with O.D. >= 5.5mm break off marked part on the Chuck
www.AAVPQ.com
6.3mm TRS Phone Jack AssemblySTEP 6
Finish the installation by tightening the bushing onto the connector
TOOLS
Cable Cutter
Cable Stripper Side
Cutters
Wire Stripper
HeatGun
Speakon – Speaker Twist Connector
PoziDriv #1 Screwdriver
www.AAVPQ.com
STEP 1 Speakon – Speaker Twist Connector
❶ Place BUSHING onto cable
❷ Place CHUCK over cable
www.AAVPQ.com
STEP 3 Speakon – Speaker Twist Connector
Prepare Cable as shown IMPORTANT
www.AAVPQ.com
STEP 3 Speakon – Speaker Twist Connector
Insert Wires into terminals
Secure Clamp terminals with screwdriver –Posidriv #1
Max torque 0.8Nm
+-
www.AAVPQ.com
STEP 3 Speakon – Speaker Twist Connector
www.AAVPQ.com
STEP 4 Speakon – Speaker Twist Connector
Push CHUCKupto Housing
Important: Align the Chuck by positioning the nose into the recess
www.AAVPQ.com
STEP 5 Speakon – Speaker Twist Connector
Push Boot uptoHousing
www.AAVPQ.com
STEP 6 Speakon – Speaker Twist Connector
Finish the installation by tightening the bushing onto the connector
TOOLS
Cable Cutter
Coax Cable Stripper
Side Cutters
Wire Stripper
BNC
Crimp Tool
www.AAVPQ.com
Slide the Bootonto the cable
BNC AssemblySTEP 1
www.AAVPQ.com
Slide the CRIMP FERRULE onto the cable
BNC AssemblySTEP 2
Position the labelling to the cable end
www.AAVPQ.com
BNC AssemblySTEP 3
Use an adjustable coaxial cable stripper
Prepare Cable as shown
4mm5mm12mm
www.AAVPQ.com
BNC AssemblySTEP 4
Don’t damage the foil (if existimg)
Spread the Braided Shield
www.AAVPQ.com
BNC AssemblySTEP 5
Position the PIN on the centre conductor
www.AAVPQ.com
BNC AssemblySTEP 6
Pin can also be soldered (optional)
Crimp the PIN with tool
www.AAVPQ.com
BNC AssemblySTEP 7
Crimp the PIN with tool
www.AAVPQ.com
BNC AssemblySTEP 8
Insert the Cable into the Connector Body
www.AAVPQ.com
BNC AssemblySTEP 9
Slide the CRIMP FERRULE over the shield to the front and push the cable to its end position until you hear a snap noiseConnector Body
www.AAVPQ.com
BNC AssemblySTEP 10
Crimp the FERRULEwith the tool
www.AAVPQ.com
BNC AssemblySTEP 11
Snap the BOOTonto the Connector Body
TOOLS
Cable Cutter
Coax Cable Stripper
Side Cutters
Wire Stripper
F- Connector
Crimp Tool
www.AAVPQ.com
F-Connector AssemblySTEP 1
Use an adjustable coaxial cable stripper
Prepare Cable as shown
www.AAVPQ.com
F-Connector AssemblySTEP 2
Fold the cable shield back onto the jacket
www.AAVPQ.com
F-Connector AssemblySTEP 3
Insert Cable into the Connector
Ensure dielectric is flush with the connector
X
www.AAVPQ.com
F-Connector AssemblySTEP 4
Dielectric flush with connector
www.AAVPQ.com
F-Connector AssemblySTEP 5
Crimp Ferrule onto Connector
www.AAVPQ.com
F-Connector AssemblySTEP 6
Dielectric flush with connector
www.AAVPQ.com
F-Connector AssemblySTEP 7
Centre conductor flush with connector body
TOOLS
Cable Cutter
etherCON 8P8C
Modular Crimp Tool
Pick
www.AAVPQ.com
Slide the Boot over the cable
STEP 1 etherCON 8P8C Assembly
www.AAVPQ.com
Assemble the RJ45 plug on the cable
STEP 2 etherCON 8P8C Assembly
www.AAVPQ.com
T568B
STEP 3 etherCON 8P8C Assembly
www.AAVPQ.com
Strip the cable Jacket
STEP 4 etherCON 8P8C Assembly
www.AAVPQ.com
Arrange the Wires in T568B order
STEP 5 etherCON 8P8C Assembly
www.AAVPQ.com
Flatten the wires
STEP 6 etherCON 8P8C Assembly
www.AAVPQ.com
Cut the Wires to 25mm
STEP 7 etherCON 8P8C Assembly
www.AAVPQ.com
Keep wire order and insert into connector
STEP 8 etherCON 8P8C Assembly
www.AAVPQ.com
Push Jacket into connector
STEP 9 etherCON 8P8C Assembly
www.AAVPQ.com
Check the Wires are in the correct order
STEP 10 etherCON 8P8C Assembly
www.AAVPQ.com
Crimp the connector
STEP 11 etherCON 8P8C Assembly
www.AAVPQ.com
Check connector is firmly crimped
STEP 11 etherCON 8P8C Assembly
www.AAVPQ.com
Cut off the Release tab of the RJ45 plug
STEP 12 etherCON 8P8C Assembly
www.AAVPQ.com
Put the CHUCK onto the cable
STEP 13 etherCON 8P8C Assembly
www.AAVPQ.com
Position the Black & Grey adapter onto
STEP 14
the connector
etherCON 8P8C Assembly
www.AAVPQ.com
STEP 15
Attention:The Connector Latch has to point downwards (opposite direction of RJ45 lettering)
Hold the assembly (RJ45 + adapters) in place with the Chuck and slide it into the housing
etherCON 8P8C Assembly
www.AAVPQ.com
STEP 16
Pay attention to the guiding key
Slide the Chuck in the Housing
etherCON 8P8C Assembly
www.AAVPQ.com
etherCON 8P8C AssemblySTEP 17
CAUTION: Max. 0.25 mm
Slide the Chuck in the Housing
www.AAVPQ.com
etherCON 8P8C AssemblySTEP 18
Slide the BOOT to the Housing and tighten the bushing
TOOLS
Cable Cutter
Cable Stripper
Solder Station
Side Cutters
Wire Stripper
XLR 5 Assembly
HeatGun
XLR 5 AssemblySTEP 3
Pin 1 - Gnd
Pin 2 - Data –
Pin 3 - Data +
www.AAVPQ.com
View – REAR FEMALE
Screwdriver
TOOLS
Cable Cutter
Cable Stripper
Solder Station
Side Cutters
Wire Stripper
HeatGun
DB9 Assembly
www.AAVPQ.com
DB9 Connector AssemblySTEP 1
Pins2 - Transmit3 - Receive5 - Shield
www.AAVPQ.com
DB9 Connector AssemblySTEP 2
Prepare STP Cable
www.AAVPQ.com
DB9 Connector AssemblySTEP 3
Strip Wires
www.AAVPQ.com
DB9 Connector AssemblySTEP 4
Tin the Conductors
www.AAVPQ.com
DB9 Connector AssemblySTEP 5
Add Solder to the Cups
www.AAVPQ.com
DB9 Connector AssemblySTEP 6
Solder Wire to Pin 2
www.AAVPQ.com
DB9 Connector AssemblySTEP 7
Solder Wire to Pin 3
www.AAVPQ.com
DB9 Connector AssemblySTEP 8
Add Heat Shrink to Shield
www.AAVPQ.com
DB9 Connector AssemblySTEP 9
Solder Shield to Pin 5
www.AAVPQ.com
DB9 Connector AssemblySTEP 10
Heat Shrink on Shield & cover transition point with larger piece
www.AAVPQ.com
DB9 Connector AssemblySTEP 11
Assemble the Cover
TOOLS
Cable Cutter
Side Cutters
Wire Stripper
powerCON
Torx #8Screwdriver
Utility Knife
www.AAVPQ.com
Insert cable into the BUSHING & HOUSING
STEP 1 powerCON Assembly
www.AAVPQ.com
Separate the HOUSING from the BUSHING
STEP 2 powerCON Assembly
Cable remains in the Bushing
www.AAVPQ.com
Place the CHUCK over the cable
STEP 3 powerCON Assembly
www.AAVPQ.com
Prepare the cable
STEP 4 powerCON Assembly
PE 23 mm
20 mm
8 mm
www.AAVPQ.com
Insert the Wires into the Terminals
STEP 5 powerCON Assembly
www.AAVPQ.com
Tighten the screw with Torx size T8
STEP 6 powerCON Assembly
www.AAVPQ.com
STEP 7 powerCON Assembly
❶ Slide the CHUCK onto the Insert
STEP 8 powerCON Assembly
❷ Slide Both CHUCK & INSERT into the HOUSING
Important: Align the Chuck & Insert by positioning the nose into the keyway
STEP 9 powerCON Assembly
Push & Turn simultaneously to slide the BUSHING up the cable
STEP 10 powerCON Assembly
Tighten the BUSHING with the tool
Important: Black O-Ring to be hidden to achieve IP Protection
