1

1080P AHD HDD MDVRUSER MANUALFTH-DVR-B7

Further Technology（Dongguan） Co., Limited

MDVR-4F1AHD professional car video recorder

----------------------------------------------------------------------------------------------------------------------------------- 2

Contents1. System Introduction........................................................................................................................ 32. Specification....................................................................................................................................43. Considerations................................................................................................................................. 74. Interface Description....................................................................................................................... 9

4.1 Front Panel Description.........................................................................................................94.1.1 Indicator Function Description.................................................................................. 94.1.2 Other definitions.........................................................................................................9

4.2 Rear View............................................................................................................................ 104.2.1 The rear panel definition.......................................................................................... 104.2.2 Power cord special instructions............................................................................... 104.2.3 Audio/video input/output Description......................................................................114.2.4 GPS、3G/4GAntenna、Wi-Fi Antenna................................................................. 13

4.3 Host installation Instruction................................................................................................ 134.3.1 Wiring diagram.........................................................................................................134.3.2 HDD Installation...................................................................................................... 154.3.3 SD card, SIM card installation.................................................................................17

5. DVR Menu Operation................................................................................................................... 175.1 Menu Structure....................................................................................................................175.2 Remote Control................................................................................................................... 19

5.2.1 System Key.............................................................................................................. 195.2.2 Menu-key Function Description.............................................................................. 205.2.3 Play Keys................................................................................................................. 20

5.3 Software operation.............................................................................................................. 205.3.1 Login........................................................................................................................ 205.3.2 Main Menu............................................................................................................... 21

6. Troubleshooting Guide..................................................................................................................39

----------------------------------------------------------------------------------------------------------------------------------- 3

H.264 Compression Mode, Support 4CH real-time 720P AHD/1080P AHD HighDefinition camera input; Exclusive pre-allocate DVR Special File SystemTechnology,Solving repeatedly wipe cause file fragmentation, solving SD card filesystem collapse, data loss and cannot find SD card and file garbled, ensure theintegrity of the data. 8-36V Adaptive Wide Voltage input, Super Low PowerConsumption Design;HDD+SD card storage (maximum support 2TB 2.5’’ hard diskand 128GB SD card. ) It can be completely resist car Vibration,Dust and others causedata corruption; Support GPS/BD/G-SENSOR ; High Reliability AviationConnectors,High Cost Performance with reliable stability,simple and clearoperation menu .

1. System Introduction

Product features

Features Details:

HIS Solution,H.264 Compression Mode, Many stream recording, 8CH Real-time720P and 8CH real-time 1080P High Definition mega pixels Camera input.

Real-time HD Video Recording, 1080P/720P/D1/HD1/CIF optional, AdjustableFrame Rate Quality.

Professional Power Design for all kinds of Vehicles, 8-36V DC Wide Voltage,Over-load, Over-voltage, Short Circuit, Reverse Protection, Suitable for all kindsof vehicles.

Support DC12V output power for camera,mini monitor and some peripheral device.HDD + SD card Data record storage (maximum 2TB 2.5’’ hard disk and 128GB SD

card. ),which can resist car vibration, dust and others cause data corruption;Watchdog Abnormal will trigger Restart Protection Function. It can better protect

Device and Video. Exclusive pre-allocate DVR Special File System Technology, Solving repeatedly

wipe cause file fragmentation, and ensure the integrity of the data. By accidents power-off protection function. Unique UPS Technology ensures the

integrality of record when power failure occurs, even can for 10-15s. Flame out Time-lapse Video Recording Function ( Maximum delay time 24 hours.) Auto Recording,Time Recording,Alarming Recording Modes for Different Request.Display vehicle traffic status, Vehicle numbers ,Route, Super-low speed vehicle

Information, Convenient management.

----------------------------------------------------------------------------------------------------------------------------------- 4

Support GPS/BD,G-sensor Modules Extension. 3channels RS232 +1channel RS485. Superior network function, support mobile SMS to configure parameters and obtain

device information. Support Video&Audio monitoring,2-way Intercom, PTZ control, manually

Alarm,Over-speed,Geo Fence etc through remote control platform. 8CH alarm inputs (Doors, lights, steering, braking, reversing and all types can be

configured), Can support kinds of response linkages. 2CH alarm output, Support the linkage acousto-optic alarm, cut off fuel

oil/power,etc . Support Local Auto-photo when alarm input,device pictures preview function; All Aviation connectors, Super stable, High Anti-shock,Easy installation Plug in and

out.Unique WINDOWS 8 interface, Easily Smart GUI Interface, Fluent system interface

is intuitive and perfect. Support SD card Remote Software Upgrade/OTA remote upgrade automatically,

partition backup technology upgrade don't crash. Support mobile phone remote monitoring, and 3G call function Supporting the ministry of communications 808 agreement, extensible PTZ control,

POS, oil flow sensor, LED advertising screen, etcCan be batch functional customization according to customer's requirements;

2. Specification

Item Parameter

OS Linux

Language Chinese/English/Others (can be customized)

Video Compression H.264 Compression Mode

OSD Overlays information such as date time and vehicle ID

GUIGraphical User

InterfaceCan connect to external LED screen. Setup system parameters with theremote control.

VideoRecord

System

Video Input 8CH 720P AHD/8CH 1080P AHD input ,aviation connector.

Video Output 2CH CVBS+ VGA output for optional, 1.0Vp-p, 75Ω,Aviation

PreviewSupport 1 channel and 4 channels preview.,Support Manual/Alarm Trigger fullscreen preview

Resolution Support 1080P/720P/D1/CIF, MAX:4 channels 1080P

Video Quality 0-7 levels, 0 is the highest level, 7 is the lowest level.

----------------------------------------------------------------------------------------------------------------------------------- 5

Video Standard

PAL: 100f/s , CCIR625 line,50field;NTSC: 120f/s, CCIR525 line,60field;CIF: 256Kbps ~ 1.5Mbps, multi levels video quality optional;HD1: 600Kbps ~ 2.5Mbps, multi levels video quality optional;D1: 800Kbps ~ 3Mbps, multi levels video quality optional;720P : 1Mbps~4Mbps, multi levels video quality optional;1080P: multi levels video quality optional;

Record ModeThe default setting is auto recording after power on. Timed recording, alarmtrigger recording and manual recording are supported.

Audio

Audio Input 8CH ,Aviation Plug

Audio Output 2CH,Front port is earphone port ,rear port connects to BNC connector.

Compression G.726 compression, 8KB/s speed

Alarm Input8CH IO Alarm Input, 1CH AD input, pulse speed input; Support alarm linkagefunction

Alarm Output2CH Relay Alarm Output, Support the linkage acousto-optic alarm, cut off fueloil/power,etc

Communication Interface

3CH RS232, support extension device, such as POS machine, Oil Feul sensor,LED advertising screen , etc.

1CH 485 interface, can connect PTZ,etc.

2CH CAN interface.

Wireless transferSupport Built-in 3G network, WCDMA,CDMA2000,TD-SCDMA compatible withGPRS,EDGE; Support Built-in 4G network, TTD-LTE, FDD-LTE

Position Support Built GPS/BD Module,can make playback analysis of vehicle routing

G-Sensor Support G-sensor

VideoStorage

Storage2.5’’ HDD+ SD Card,each max 2TB HDD + 128GB SD Card mirror recording toprotect data from loss

UpgradeSupport USB flash disk updating,SD card upgrade , OTA remote upgradeautomatically

File Format .ASF

File System Special Car system File System

USBFront panel supports USB port, support USB flash disk upgrade to backup;hard disk box USB port, can back up video data

VideoPlayback

Video Search Search video by Record Time/Record Type etc

PlaybackMax support 4CH Replay /Stop/Fast Forward/Fast Reverse at same time

Support x 2,x4,x8,x16. fast forward or fast backward play

Safety Management User/Admin 2 Levels Different Passwords , support screen lock

Voltage &Power

Consumpti

PowerManagement

Adaptive wide power input, support Wide Voltage, Over-load、Over-voltage、Short Circuit、Reverse Protection..Support Time Setting/Delay power off

Voltage Input DC:+8V ~ +36V

----------------------------------------------------------------------------------------------------------------------------------- 6

on Voltage Output +12V@2.5A，+5V@2.5A

Power-offProtection

UPS Technology,All video information can be saved automatically when thepower is cut off, and make sure that all the files can not be damaged.

PowerConsumption

Normal Working ＜10W

WorkingEnvironme

nt

Temperature -20℃ to +70℃

Humidity 20% to 80%

othersSize 200 （D）* 187（W）* 65（H） mm

Net Weight 2.15kg

***** Above parameters any changes,please refer to actual product *****

----------------------------------------------------------------------------------------------------------------------------------- 7

3. ConsiderationsIn order to ensure the safely use of FTH-DVR-B7 Mobile DVR device, please

carefully read and observe the following precautions:

3.1 when installing and operating the equipment, comply with all the norms ofelectronic products, as well as vehicles and other connected equipment.

3.2 Power and Ground:

i. The Projector range of DC input power directly 6V to 36V, often powered fromthe vehicle battery (or distribution box) To take power, please be careful not toreverse the output can not be short, please note that the power supply load line,the positive and negative power supply line diameter must be used Φ1.5 above.

ii. even when the device is closed, also charged in the machine, to avoid shortcircuits, before connecting other external devices, disconnect the device fromthe power source (such as audio and video yellow and green lines in the powersupply wiring are not red phase touch and wrong).

iii. Equipment native external output voltage of 12V, only for the power supply forthe camera, do not come with any not specified on the device allows the use ofa device.

iv. correct device ground connection to the vehicle's ground wire loop composition.

v. If the machine does not use long, preferably completely disconnect the powersupply to prolong life.

3.3 Humidity::installation of equipment in a dry environment, avoid moisture, drip,sprinkler and other places, do not install the equipment in the recess. It will placewater or liquid dripping wet places.

3.4 Installation position:

vi. To extend the life of the equipment, if possible, the equipment installed in thevehicle vibration weaker parts.

vii. The equipment should be installed in a vehicle ventilated areas: equipmentinstalled on the plane should be kept 6 inches (15 centimeters) away from otherobjects, in order to facilitate the flow of air and heat; can not be installed in aclosed space.External wire have enough space and outer flame tube

viii. protection devices to ensure that the wire is not bent or worn in shock andleakage.

ix. ensure that heat away from the device on the vehicle, the device can not havedebris piled up around the forbidden place anything on the device

3.5 Device Security:

x. ensure that passengers can not interfere with the driver or damage toequipment and parts, cameras, cables and other accessories, do not install near

----------------------------------------------------------------------------------------------------------------------------------- 8

other vehicle components restricted areas.

xi. installation of equipment components, cameras, accessories, and when the wire,launch vehicle may cause damage to the equipment, make sure the vehicle isstationary during installation, to prevent the unit from dropping.

xii. screws fastening the device must be strong, can not loose, to ensure thestability of the device.

----------------------------------------------------------------------------------------------------------------------------------- 9

4. Interface Description

4.1Front Panel Description

4.1.1 Indicator Function Description[PWR] Power Status Indicator: LED lit ─ charging system

[GPS] GPS status light: LED flashes ─GPS loaded successfully

[HOT] heating status lights: Reserve

[HDD] HDD LED: LED lights ─ hard disk loading. LED flashes ─ a description of thisdisc is recording or reading and writing data

[SD] SD indicator: LED lights ─SD Calgary uploaded successfully. LED flashes ─ adescription of this disc is recording or reading and writing data

[REC] Video light: LED lit indicates ─ is recording

[Alarm] machine running warning lights: When the alarm is triggered, Alarm lights lit

[NET] NET indicator: LED lights ─ network load successfully

4.1.2 Other definitions[IR] IR receiver: for receiving remote control signals

[USB] USB interface

[LOCK] HDD Lock: no lock, the host can not start

[V-OUT] composite video signal output port

----------------------------------------------------------------------------------------------------------------------------------- 10

4.2Rear View

4.2.1 The rear panel definition● [DC8-36V] Power Interface: left upper and lower 2PIN is DC +, down the middle 2PIN

is DC-, is on the right side 1PIN ACC, under the right of 1PIN is 12V-OUT.● [NET] network interface.● [I/O] ALM/232/485/CAN interface。● [PANEL] 232 / MIC / SPK expansion interface.● [VIN1-8] audio and video input interfaces.● [VGA] VGA video output interface.● [3G / 4G] 3G / 4G antenna interface.● [WIFI1-M] WIFI antenna interface.● [GPS] GPS antenna interface.

4.2.2 Power cord special instructions

----------------------------------------------------------------------------------------------------------------------------------- 11

4.2.2.1 Power cable pin definitions

Color Line Name Description

Red DC+ Power-Positive

Black DC- GND

Yellow ACC ACC

Red 12V-OUT 12V output

4.2.2.2 Wiring: red and black wire are connected directly to the car battery. Red wire to

positive, black to negative. Yellow line contacts FireWire, ignition switch mode is set to

mode. The DVR device turns on when the vehicle power on,DVR turn off automatically the

vehicle power off. Yellow line connected to the car keys to open the position (that is,

before the automobile starter motor gear) all the dashboard lights.

Note: 1) Before connecting wires,one need to make sure the battery voltage is

between 6V ~ 36VUU, otherwise it will be burned;

2) After connecting the cable, pay attention to insulation of the line between

lines to prevent short circuit and burned out the battery;

3) yellow line must be connected to the firing line, otherwise the device will not

support the ignition switch;

4) Special Note: 12V-OUT line can not be connected to the power input by

mistake, which can not be connected to ground by mistake;

5) Note: DVR installation must be connected to battery positive and negative

directly, can not be done with ground grounding, grounding will produce negative glitch

host running. Positive and negative power supply line diameter must be Φ1.5 above.

4.2.3 Audio/video input/output Description

【VIN1 -VIN4】Video output 1-4

----------------------------------------------------------------------------------------------------------------------------------- 12

Female connector definition：PIN 1 2 3 4 5 6

Function 12V output Audio input1 GNDVideoinput 1

Videoinput2

Audioinput 2

Color Red White Black Blue Yellow Green

Male signal connector definition：PIN 1 2 3 4

Function 12V output GND Audio input Video inputColor Red Black Green/White Yellow/Blue

【AV-OUT】Audio/Video output

PIN 1 2 3 4Function 12V output GND Audio output Video outputColor Red Black Green Yellow

GND (black)

Audio (green)

+12V (red)

Video (yellow)

Female

----------------------------------------------------------------------------------------------------------------------------------- 13

4.2.4 GPS、3G/4G Antenna、Wi-Fi Antenna

GPS Antenna 3G/4G Antenna Wi-Fi Antenna

4.3Host installation Instruction

4.3.1 Wiring diagram

Power Line camera4

WIFI antenna

camera3

camera2 camera1

speaker/232

Alarm lines for people counter/oil

sensor/Tyre sensor etc

3G/4G antennaGPSAntenna

LAN/RJ45

----------------------------------------------------------------------------------------------------------------------------------- 14

ALM/232/485/CAN connection lines

----------------------------------------------------------------------------------------------------------------------------------- 15

ALM/232/MIC/SPK extension lines

Power Cables

Line

colorItem Remark

Red DC+ Power positive

Black DC- GND

yellow ACC ACC line

Red 12V-OUT 12V output

4.3.2 HDD Installation

Hard disk installation steps:

1、Open the hard disk lock and un-screw the 2 fixing screws, pull out the hard disk

box,, as shown in FIG.

----------------------------------------------------------------------------------------------------------------------------------- 16

2、Unscrew 4pcs screw on HDD box，as show below

3.Install shock absorption foam on both sides of the hdd, connect the HDD with

SATA lines,fix the HDD into the dedicated ditch, as shown below

HDD installation diagram

4、Closing lid, playing screws,as shown below

LockHDD box Box Fixing screw1Box Fixing screw2

HDD box screw HDD box screw

HDD box screwHDD box screw

ear

ear

SATA line

----------------------------------------------------------------------------------------------------------------------------------- 17

Note: Be sure to lock the hard disk installed hard disk lock, otherwise the host may

not start.

4.3.3 SD card, SIM card installationWith a key to open the box to pull out the hard disk box, , then you can see SD card

port, as shown below. The SD card with the SD card port is pressed into place (notepositive and negative, insert the top right corner of the SD card with the notched SDcard inserted).

5. DVR Menu Operation

5.1 Menu Structure

SD slotSIMcard slot

HDD box screw HDD box screw

HDD box screwHDD box screw

----------------------------------------------------------------------------------------------------------------------------------- 18

Menu Diagram

Login

Menu

Inquiry

SystemManage

Video

Set

Netw

ork

Alarm

Set

SystemInfor

Inquiryvideo,log,and

pictures

Device

inforset

UserLogin

Set

SystemParam

eter,Time

Video

recordset

Previewand

OSD

StorageParam

eterset

ServerParametersetting

APN

Dial/W

IFIset

I/OAlarm

/SpeedAlarm

Voltage/PTZset

----------------------------------------------------------------------------------------------------------------------------------- 19

5.2 Remote Control

5.2.1 System Key

【 】: Turn on/ off key

【Info】: Info. Key (retain)

【 】:Lock. Press this key to lock remote input after exiting menu.

【 】: Switch 1~4 screens. Number keys 1~4 can do this too.

----------------------------------------------------------------------------------------------------------------------------------- 20

【Del】:Delete key.

【Number/Letter】 Input key, you can input the number value to select a single

channel preview.

5.2.2 Menu-key Function Description

【MENU】Start/Login/Exit menu

【EXIT】Back to the previous menu

【 】 Last program

【 】Next program

【 】Modify the current item/last subproject

【 】Modify the current item/next subproject

【OK】Confirm

5.2.3 Play Keys

【 】:Play/Pause

【 】: Stop

【 】:Fast forward. 1/2/4/8/60

【 】: Rewind. 1/2/4/8/60

【 】：Frame forward

5.3 Software operation

5.3.1 LoginPress the remote control [MENU] key to enter the login screen:

----------------------------------------------------------------------------------------------------------------------------------- 21

Press【OK】to enter the edit mode, input password , press【EXIT】to exit the edit,Press【OK】 to enter the Main Menu.

Original Password: 111111

5.3.2 Main Menu

【EXIT】Exit Menu

----------------------------------------------------------------------------------------------------------------------------------- 22

5.3.2.1 InquiryFunction: Query the recording information.

Operation: In the main menu, press the remote control 【 】【 】【 】【 】 key, selectand operate.

[Image Search] Function: Search preferred video information.Operation：In query interface, press remote control key【 】【 】【 】【 】,select

[RECORD],press [ENTER] and go to video search Menu as below

Select the right time and search the video

----------------------------------------------------------------------------------------------------------------------------------- 23

[Log Search]: query log information.Operation：In query interface, press remote control key【 】【 】【 】【 】,select

[Log Search],press [ENTER] and go to video search Menu as below

[Image Query]: query image information.Operation：In query interface, press remote control key【 】【 】【 】【 】,select

[Image Search],press [ENTER] and go to log search Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 24

5.3.2.2 System ManagementFunction: Set each property of the Device.Operation：In query interface, press remote control key 【 】【 】【 】【 】,select[System Management],press [ENTER] and go to video search Menu as below

In the System settings interface, press on the remote control 【 】【 】【 】

【 】 Keys, select the right item to set up

[Terminal Setup] Function: Change the terminal device parameters.Operation：In query interface, press remote control key【 】【 】【 】【 】,select

[Terminal Setup],press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 25

[User Management] Function: Manage the user information.Operation：In user manage interface, press remote control key 【 】【 】【 】

【 】,select [User Management],press [ENTER] and go to the Menu as below

[System time] Function: set up the system time.Operation：In system time interface, press remote control key 【 】【 】【 】

【 】,select [system time],press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 26

[Power manage] Function: set up the DVR power on/off parameters.Operation：In power manage interface, press remote control key 【 】【 】【 】

【 】,select [power manage],press [ENTER] and go to the Menu as below

[Parameter Set] Function: set up/Import/Export/Recover the DVR Parameters..Operation：In system set up interface, press remote control key 【 】【 】【 】

【 】,select [parameter manage],press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 27

[Format] Function: Format DVR storage medias(USB1--HDD)..Operation：In system set up interface, press remote control key 【 】【 】【 】

【 】,select [format],press [ENTER] and go to the Menu as below

5.3.2.3 Record SettingIn Main Menu interface, press remote control key 【 】【 】【 】【 】,select

[video set],press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 28

[Basic set] Function: Set up video record and display basic parametersOperation：In the video set up interface, press remote control key 【 】【 】

【 】【 】,select [Basic set],press [ENTER] and go to the Menu as below

[Main video stream] Function: Modify the main video stream parametersOperation：In the video set up interface, press remote control key 【 】【 】

【 】【 】,select [Main video stream],press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 29

[Sub-stream] Function: Modify video sub-stream parametersOperation：In the video set up interface, press remote control key 【 】【 】

【 】【 】,select [Sub-stream],press [ENTER] and go to the Menu as below

[Timer recording] Function: Set up Timer recording.Operation：In the video set up interface, press remote control key 【 】【 】

【 】【 】,select [Timer recording],press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 30

[Storage Set] Function: Set up Storage items.Operation：In the video set up interface, press remote control key 【 】【 】

【 】【 】,select [Storage Set],press [ENTER] and go to the Menu as below

[OSD] Function: Modify video display overlay informationOperation：In the video set up interface, press remote control key 【 】【 】

【 】【 】,select [OSD],press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 31

5.3.2.4 Network Setting[Network] Function: Set up network parametersOperation：In the Main Menu interface, press remote control key 【 】【 】【 】

【 】,select [Network],press [ENTER] and go to the Menu as below

[Center Set] Function: Set up network center parametersOperation：In the Network Menu interface, press remote control key 【 】【 】

【 】【 】,select [Center set],press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 32

[Local Set] Function: Set up local network parametersOperation：In the Network Menu interface, press remote control key 【 】【 】

【 】【 】,select [Local set],press [ENTER] and go to the Menu as below

[Dial-up settings] Function: Set up Dial-up settings parametersOperation：In the Network Menu interface, press remote control key 【 】【 】

【 】【 】,select [Dial-up settings], press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 33

[WIFI settings] Function: Set up WIFI parametersOperation：In the Network Menu interface, press remote control key 【 】【 】

【 】【 】,select [WIFI settings], press [ENTER] and go to the Menu as below

5.3.2.5 Alarms and PeripheralsIn the Main Menu interface, press remote control key【 】【 】【 】【 】,select

[Alarms and Peripherals], press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 34

[IO Alarm] Function: Set up IO alarm parametersOperation：In the Alarm Menu interface, press remote control key 【 】【 】

【 】【 】,select [IO Alarm], press [ENTER] and go to the Menu as below

[Speed Alarm] Function: Set up IO alarm parametersOperation：In the Alarm Menu interface, press remote control key 【 】【 】

【 】【 】,select [Speed Alarm], press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 35

[Acceleration] Function: Set up Acceleration parameters, so convenient forrecording video collection

Operation：In the Alarm Menu interface, press remote control key 【 】【 】

【 】【 】,select [Acceleration], press [ENTER] and go to the Menu as below

[Motion Detection] Function: Set up Motion Detection parameters, so convenientfor recording video collection

Operation：In the Alarm Menu interface, press remote control key 【 】【 】

【 】【 】,select [Motion Detection], press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 36

[Voltage alarm] Function: Set up voltage alarm parametersOperation：In the Alarm Menu interface, press remote control key 【 】【 】

【 】【 】,select [Voltage alarm], press [ENTER] and go to the Menu as below

[Serial Management] Function: Set up Serial Management parametersOperation：In the Alarm Menu interface, press remote control key 【 】【 】

【 】【 】,select [Serial Management], press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 37

[PTZ control] Function: Set up PTZ control parametersOperation：In the Alarm Menu interface, press remote control key 【 】【 】

【 】【 】,select [PTZ control], press [ENTER] and go to the Menu as below

5.3.2.4 System information[System Information] Function: Check syetem key parametersIn the Main Menu interface, press remote control key【 】【 】【 】【 】,select

[System Information], press [ENTER] and go to the Menu as below

----------------------------------------------------------------------------------------------------------------------------------- 38

Click【ENTER】，go to next page：

----------------------------------------------------------------------------------------------------------------------------------- 39

6. Troubleshooting Guide

Question Possible reasons SolutionsDevice does not workandthere is no indicator lightworking.

a. Wrong wiring connectionb. Not install power inputfusec. Input fuse is burned off

a. Right wiring connectionb. Install fusec. Replace fuse

There is no video output,but power indicator islight.

a. Wrong wiring connectionb. Monitor is off.c. DVR lock is Offd. ACC is not connected withignition wire.e. Device is set as timerrecording

a. Right wiring connectionb. Start monitorc. DVR lock is Ond. ACC is connected withignition wire.e. Turn on device withremote control.

There is video output,butcannot be query video

file.

a. SD Card is damaged.b. No SD card in devicec. SD Card not formatd. Device does not record

a. Replace SD cardb. Insert SD cardc. Format SD card andrestart deviced. Check whether the video

mode of the device is onthe boot recording

Device is Off afterworking 30 minutes.

a.ACC is not connected withignition wire

a.ACC is connected withignition wire

Some channels imagesare black screen.

a. This channel is not connected tothe videob. Camera damage or workexception to this channelc. Connection to this channel cable isnot good or damage

a. Connection videob. Check the camera is normal ornot.c. Check channel cable

3G is not on line (limited to3G network)

a. 3G card is not insertedb. 3G card is not open or no moneyc. 3G network setup errord. Server IP, port, device number

setting error

a. Check whether the 3G card isinserted.

b. Check whether the 3G card isopen and whether there is afee

c. Check whether 3G networksettings are correct

d. Check whether Server IP, port,equipment number is correct