User Manual - makewebeasy...PROFILER REVOLUTION (REF. 6700) 7 There are 2 modes to add channels to...

User Manual

Profiler Revolution

Ref. 6700

PATENT PENDING

SW Version 1.3.0

PROFILER REVOLUTION (REF. 6700)

2

CONTENTS

1. INTRODUCTION ............................................................................... 3

1.1. Product description ................................................................................... 3

1.2. Typical installation .................................................................................... 3

1.3. Package contents ..................................................................................... 3

1.4. Hardware installation ................................................................................ 4

1.5. Mounting the Profiler Revolution ................................................................. 4

1.6. Configuring the Profiler Revolution .............................................................. 5

2. TECHNICAL SPECIFICATIONS ............................................................ 11

3. BLOCK DIAGRAM ............................................................................ 12

4. SAFETY INSTRUCTIONS ................................................................... 13

5. CONDITIONS OF WARRANTY ............................................................. 14

No part of this manual may be copied, reproduced, transmitted, transcribed or translated into any language without permission.

Unitron reserves the right to change the specifications of the hardware and software described in these manuals at any time.

Unitron cannot be held liable for any damages resulting from the use of this product. Specifications are subject to change without notice. 05/18

© Unitron - Frankrijklaan 27 - B-8970 Poperinge - Belgium

T +32 57 33 33 63 F +32 57 33 45 24

[email protected]

www.unitrongroup.com

mailto:[email protected]

http://www.unitrongroup.com/


3

1. INTRODUCTION

1.1. Product description

The Johansson Profiler Revolution is an easy to use programmable filter amplifier and convertor

for terrestrial signals. The module optimizes terrestrial VHF/UHF and FM signals from multiple

inputs with the goal to provide high quality images on your TV screen. The state-of-the-art

programmable filter amplifier has no equivalent on the market due to its revolutionary

technology:

• Can process more than 50 channels

• Can convert a wide selection of channels

• Sharpest filters on the market (50 dB on adjacent channels)

• Real-time AGC on all individual multiplexes

• Complete flexibility in assigning filters from any input. Each channel can be frequency

shifted to any other channel in the VHF or UHF band (Flex Matrix)

• To avoid unauthorized persons changing the settings, all Profiler products can be locked

with a security code

• Made in Europe, for worldwide application

• 5 inputs: FM / 4 x VHF-UHF / > 50 channels / AGC / 12-24 V remote power

• Product dimensions (H X W X D): 165mm x 217mm x 59mm

1.2. Typical installation

The Profiler Revolution can be used to provide high quality television images and FM signals in a wide range of projects, both in the hospitality as in the residential market.

Typical buildings or infrastructures where the Profiler Revolution can be used include, but are not limited to:

• Large and small hotels, hostels, bed and breakfasts, holiday parks

• Hospitals, rest homes, prisons, settlements

• Large and small multi-dwelling units

1.3. Package contents

• 1 Profiler Revolution (ref. 6700)

• 1 Power Adapter Cord (180cm)


4

1.4. Hardware installation

FIGURE 1: TOP VIEW OF PRODUCT

1.5. Mounting the Profiler Revolution

• Important: Mount the module vertically to a wall

in a well-ventilated room and leave a minimum

space of 15 cm around the product to guarantee a

maximum ventilation of the product

• Connect an earth wire to the grounding clamp

• Connect the power adapter cord to the power

supply socket. Check the status LED for the

indication of DC power presence

• Connect the VHF/UHF and/or FM inputs to the

Profiler Revolution

• Connect a coaxial cable to the output connector for distribution of the signal

• Connect a network analyser to the test port to control the signal quality

• Configure the Profiler Revolution using the rotary button, see below

• Optionally: insert an SD card in the SD card slot to upload the configurations of a

previous module or to copy the configuration to another module

• The power adapter can easily be replaced without disconnecting the product. To do so,

open the top left plastic cover by pushing the click at the opposite side of the mains

connector


5

1.6. Configuring the Profiler Revolution

NAVIGATING THROUGH THE MENU

Use the Johansson rotary/push button to navigate through the menu. This is very

straightforward and simple. The table below shows how the rotary/push should be used:

Push the button 2s to enter the basic

configuration.

Push the button to confirm your

selections.

When rotating the button, you scroll

through the different screens.

MENU OVERVIEW

INPUT FM INPUT V/U 1 - 4 OUTPUT ADVANCED LOAD SD PRESET SAVE SD PRESET EXIT

GAIN PRE-AMPLIFIER LEVEL LANGUAGE PRESET X CREATE PRESET LOCK

DC SLOPE REGION DELETE ALL NO LOCK

ADD 1 CHANNEL DC VOLTAGE

ADD 2 CHANNELS FILTER

FW VERSION

SERIAL NUMBER

FORMAT CARD

UPGRADE FW

REGION/COUNTRY SETTINGS

IMPORTANT! Before starting the configuration, it is advised

to set the correct region or country. Unpower the unit, push the button and keep pushing the button while you repower the unit. Release the button when the display shows “RESET FINISHED”. Now the product

is reset and will ask you to enter country or region. This will amongst others determine the

channel plan for VHF and UHF and the DC voltage for the inputs (12 or 24V).


6

DISPLAY READOUT EXPLANATION

To activate the correct channel frequency plan, select

the country or region where the Profiler Revolution is

situated. Rotate to select and confirm by tapping the

rotary button.

The default setting is Europe. The Profiler Revolution is

also operational in the following countries/regions:

Australia, Brazil, China, Hongkong, Italia, New-

Zealand, Russia, South Africa, UK and USA.

All the following menu items can be accessed without the reset procedure.

Push the rotary button for 2 seconds to access the menu

INPUT SETTINGS


Tap the rotary button to enter the INPUT FM menu.

Rotate the button to navigate through the submenu.

To filter and amplify an FM signal, tap GAIN, select the

gain of the input FM signal (15 to 35 dB) and tap to

confirm.

Remark: DAB should be added via V/U input 1-4.

After INPUT FM is configured, scroll up to the top of the

menu (INPUT FM), tap the rotary button and scroll

right to INPUT V/U 1. Tap INPUT V/U 1 to enter the

menu to configure input 1.

Rotate the rotary button to scroll down in the submenu

of INPUT V/U 1.

PRE-AMPLI: The internal amplifier is by default ON,

only in case of very strong incoming signals (if the

strongest channel on that input is higher than

80dBµV), it can be advised to switch this OFF.

DC: Decide whether the input should provide power to

an external amplifier. Choose between OFF or 12 V.

Remark: If the external amplifier needs 24 V, you can

change this in advanced settings (see further).


7

There are 2 modes to add channels to each input:

• ADD 1 CHANNEL: This is the standard mode where you add channels one by one to

an input. This implies that channels are filtered and levelled individually.

• ADD 2 CHANNELS: In this mode you add 2 adjacent channels to an input. This

enables you to process more than 50 channels. The 2 channels are processed

together as 1 cluster. This means that the input level, shown on the display, and the

output level are both the sum of signal strength of the 2 channels.

For optimal performance we recommend to only add single channels, unless you need to

process a lot of channels.


ADD 1 CHANNEL:

Tap ADD 1 CHANNEL and choose the channel you want

to receive. Tap to confirm.

By changing the second value, you can decide where to

place the channel at the output. Tap to confirm.

1 CHANNEL mode is indicated by a ‘>’

CONVERSION OF A CHANNEL: If the 2 channel

numbers indicate the same value, there is

no conversion. If the 2 channel numbers indicate a

different value, there is conversion. In this example, if

the display is set to show 21> 5, the received channel

21 is converted or frequency shifted to the output

channel 5.

ADD 2 CHANNELS:

Tap ADD 2 CHANNELS and choose the adjacent pair of

channels you want to receive.

Tap to confirm.

2 CHANNELS mode is indicated by a ‘+’

When adding 2 channels, conversion is not

possible.

Remark1: The first channel will determine if your input

becomes a VHF only or UHF only input. This means that

VHF and UHF cannot be combined in one input.

Remark 2: The value 60dBµV (in the bottom right

corner) indicates the incoming level of the channel.

Remark 3: For EU, Italy and New-Zealand region,

Channel 13 (230-240MHz) and “VHF” can be used.

“VHF” means the whole band is treated in 1 bandpass

filter from 174 to 240MHz. Channels “VHF” and CH13

cannot be converted and are not part of the 2-channel

mode, as they have different bandwidths.

Note: it might take up to 20 seconds for the AGC to stabilize the signal levels


8


To add another channel, scroll down to ADD 1

CHANNEL or ADD 2 CHANNELS and tap to confirm.

To prevent bad quality or scrambled images, make

sure that only one input channel is assigned to one

output channel. If 2 channels are assigned to the same

output channel, a star () will appear.

The same applies for adding 2 channels. Make sure

that each output channel is selected only once.

Add all the input channels you want and assign them to

the output channels.

After this, the correct LTE filter will be set for the input (possible filters are 694MHz, 790MHz or

OFF). If the channels are lower than 48, the 694MHz filter is activated. The 790MHz filter is

activated for the channels lower than 60.

To delete a (pair of) channel(s), position the arrow on the channel and press the rotary button 3 seconds.


To delete a (pair of) channel(s), position the arrow on

the channel and press the rotary button 3 seconds.

When you have added all the channels to INPUT V/U 1,

and you want to add channels to the other inputs,

scroll up to the top of the menu (to INPUT V/U 1), tap

the button and scroll to the next input.

Repeat the previous steps for all input channels.


9

OUTPUT SETTINGS


Define the OUTPUT LEVEL of the output signal.

Range between 93 dBµV and 113 dBµV (default output

level is 103 dBµV). Check the output via a network

analyser on the -30dB test port.

Note: The more channels you select, the less input

power you should give (e.g. 106 to 110 dBµV for 10

channels).

A SLOPE of up to -9dB can be set between the

beginning of BIII and the end of UHF to compensate for

cable losses. 0dB means all channels have the same

output level (see previous display readout), -9dB

means the beginning of BIII (174MHz) is 9dB weaker

than the end of UHF.

Note: In the OUTPUT menu, you define the output level in dBµV of the MUX’s. The Profiler

Revolution has enough gain to guarantee this output level under all input conditions. In case a

slope has been set, the output level indicated on the display will be the output level of the

highest frequency MUX.

ADVANCED SETTINGS


The language of the Profiler Revolution can be set to

English, Italian, Spanish or French.

Tap REGION to check to which region/country the

Profiler Revolution is set. To change the

region/country, a hard reset is required (see

instructions above (cfr. REGION/COUNTRY SETTINGS).

Define DC VOLTAGE for the inputs, choose between

12V or 24V. This is a global setting for all inputs, each

input can then be switched between OFF or this value.

(cfr. STEP 2). All countries are set by default on 24V,

except UK which is set by default on 12V.

There are 3 options to select the filter bandwidth:

“Best MER” has the widest filter bandwidth. This will

give the best MER in case where there are no adjacent

Multiplexes. “Sharp” has the narrowest bandwidth and

will work best when there are difficult adjacent

Multiplexes but this could be at the expense of the

overall MER performance. “Optimal” is the compromise

between the other 2 options. This is the best setting in

95% of the cases.


10

Tap FW VERSION to check the firmware version of the

device.

Tap SERIAL NUMBER to check the serial number of the

device.

To format the SD CARD, tap FORMAT CARD.

To upgrade the firmware of the device, tap UPGRADE

FW. Make sure the new firmware file is on the SD Card

before upgrading.

SD CARD SETTINGS


To upload settings from a SD card, tap LOAD SD

PRESET. This will copy the configuration file from the

SD CARD to the device.

To save the device settings on the SD CARD, go to

SAVE SD PRESET and tap on CREATE PRESET.

It is possible to create multiple presets. Therefore, tap

CREATE PRESET after each modification of the settings.

To delete all presets, press DELETE ALL.

EXIT SETTINGS


To avoid unauthorized people changing the settings, all

Profiler products can be locked with a security code.

Select LOCK and SET LOCK CODE.

When the lock code is set, the device will shut down.

When you restart the device, you will now have to

enter the correct lock code.

Remark: If you forgot the lock code, you can always

use the value 50. This master code is fixed and cannot

be changed.

If you do not want to work with a lock code, go to EXIT

and tap NO LOCK.


11

2. TECHNICAL SPECIFICATIONS

Profiler Revolution 6700 Inputs - 4 VHF/UHF + 1FM

Outputs - 1 main (FM-VHF-UHF) + 1 test port (-30dB)

Frequency range MHz MHz MHz

FM: 88 - 108 VHF:174 - 240 UHF: 470 - 862

LTE protection MHz Automatic selection: 694, 790 or OFF

Input level dBµV dBµV dBµV

FM: 37 - 77 VHF: 40* - 109 UHF: 40* - 109

FM Output power (60dB/IM3) VHF/UHF Output power (60dB/IM3) VHF/UHF Output power with 1 MUX VHF/UHF Output power with 6 MUX

dBµV dBµV dBµV dBµV

113 120 113 110

Conversion - Yes (from any VHF-UHF channel to any VHF-UHF channel)

Gain dB dB dB

FM: 35 VHF: >45 UHF: >55

Gain adjustment : FM VHF/UHF

dB -

20 Channel AGC

General attenuator dB 20

Slope adjustment dB 9

Selectivity dB/1MHz 35

Output MER dB dB

VHF: 35 UHF: 35

ESD protection - All inputs

Remote voltage for preamp

Remote current

V

mA

12 or 24

100 (total for the 4 inputs)

SD port - Yes (for copy configuration and upgrade features)

Operating temperature °C -5 to +50

Power Supply Vac 100 - 240

Power consumption W 16

Dimensions mm 217 x 165 x 59

Weight kg 0,8

* For 64QAM with code rate 3/4


12

3. BLOCK DIAGRAM


13

4. SAFETY INSTRUCTIONS

Read these instructions carefully before connecting the unit

To prevent fire, short circuit or shock hazard:

• Do not expose the unit to rain or moisture.

• Install the unit in a dry location without infiltration or condensation of water.

• Do not expose it to dripping or splashing.

• Do not place objects filled with liquids, such as vases, on the apparatus.

• If any liquid should accidentally fall into the cabinet, disconnect the power plug.

To avoid any risk of overheating:

• Install the unit in a well aired location and keep a minimum distance of 15 cm around the

apparatus for sufficient ventilation

• Do not place any items such as newspapers, tablecloths, curtains,

on the unit that might cover the ventilation holes.

• Do not place any naked flame sources, such as lighted candles, on the apparatus

• Do not install the product in a dusty place

• Use the apparatus only in moderate climates (not in tropical climates)

• Respect the minimum and maximum temperature specifications

To avoid any risk of electrical shocks:

• Connect apparatus only to socket with protective earth connection.

• The mains plug shall remain readily operable

• Pull out power plug to make the different connections of cables

• To avoid electrical shock, do not open the housing of adapter.

Maintenance

Only use a dry soft cloth to clean the cabinet.

Do not use solvent

For repairing and servicing refer to qualified personnel.

Dispose according your local authority’s recycling processes


14

5. CONDITIONS OF WARRANTY

Unitron N.V. warrants the product as being free from defects in material and

workmanship for a period of 24 months starting from the date of production indicated on

it. See note below.

If during this period of warranty the product proves defective, under normal use, due to

defective materials or workmanship, Unitron N.V, at its sole option, will repair or replace

the product. Return the product to your local dealer for reparation.

THE WARRANTY IS APPLIED ONLY FOR DEFECTS IN MATERIAL AND

WORKMANSHIP AND DOES NOT COVER DAMAGE RESULTING FROM:

• Misuse or use of the product out of its specifications,

• Installation or use in a manner inconsistent with the technical or safety standards in

force in the country where the product is used,

• Use of non-suitable accessories (power supply, adapters...),

• Installation in a defect system,

• External cause beyond the control of Unitron N.V. such as drop, accidents,

lightning, water, fire, improper ventilation…

THE WARRANTY IS NOT APPLIED IF

• Production date or serial number on the product is illegible, altered, deleted or removed.

• The product has been opened or repaired by a non-authorized person.

NOTE

Date of production can be found in the product’s serial number code. The format will either

be “YEAR W WEEK” (e.g., 2017W32 = year 2017 week 32) or “YYWW” (e.g., 1732 = year

2017 week 32).

UNITRON NV

Frankrijklaan 27

B-8970 Poperinge

Belgium

T +32 57 33 33 63

F +32 57 33 45 24

[email protected]

www.unitrongroup.com

mailto:[email protected]

User Manual - makewebeasy...PROFILER REVOLUTION (REF. 6700) 7 There are 2 modes to add channels to...

Documents

Transcript of User Manual - makewebeasy...PROFILER REVOLUTION (REF. 6700) 7 There are 2 modes to add channels to...