User Manual for GSM900 Band Selective Pico Repeater.pdf
Transcript of User Manual for GSM900 Band Selective Pico Repeater.pdf
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
1/31
USER MANUAL FOR GSM900 BAND
SELECTIVE PICO REPEATER
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
2/31
CONTENT
1. Product Introduction ............................................................................................................... 3
2. Usage scope .......................................................................................................... ................... 3
3. Characteristics.......................................................................................................................... 4
4. Specifications ........................................................................................................ ................... 5
5. Product Description ................................................................................................................. 8
6. Installation instructions ........................................................................................................... 9
7. Indicator Instruction Table ................................................................. .................................... 10
8. Local Setup steps ................................................................................................................... 12
9. NMS Setup steps ................................................................................................... ................. 21
10. Service after Sale ............................................................................................................... 30
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
3/31
1. PRODUCT INTRODUCTION
The GSM900 BAND SELECTIVE Pico Repeater provides an affordable solution to solve the indoor signal
coverage problems in GSM900 system due to signal fading and attenuation caused by architectureobstacles. And its easy installation and maintenance can help carrier get fast return.
The Pico-repeater is working as a relay between the BTS and mobiles. Pico Repeater is applied
specially in small area indoor DAS system. The base station signal is coupled and amplified by Pico
Repeater into in-building system. The amplified signals are transmitted by indoor antenna. Meanwhile
the indoor antenna receives the cell phone signal, and sends the signal to the base station as uplink.
This method can eliminate the signal dead spot, reject the interference, and provide the stable signal
communication for cell phone users. This Pico Repeater mainly solves the problem spot problem in
building.
Pico Repeater is a bi-directional amplifier that allows for the reception of signals, amplifies the signal
and re-transmits into areas where there is no or very low signal level coverage enabling mobile userto establish a call connection.
Pico Repeater can be deployed in indoor coverage. It is especially advantageous to use in 100-1000
sq.m, which is a very economical solution.
2. USAGE SCOPE
To expand signal coverage or fill signal blind area where signal is weak or unavailable.
residential house villas
basements Hotels
parking lots exhibition centers
border village
offices vessels
shopping malls tunnels
countryside mines
Clubs underground facilities
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
4/31
FIGURE 1 APPLICATION DIAGRAM
3. CHARACTERISTICS
AUTOMATIC LEVEL CONTROL FUNCTION
With the function of digital ALC, the dynamic gain adjustment range is more than 20dB. It ensures the
Pico Repeater works in linear status and provides the high reliability and stability.
SELF-OSCILLATION AUTOMATIC DETECTION FUNCTION
It has the function of self-oscillation automatic detection (It detects the isolation when boot time),
which detects the self-oscillation occurred by inadequate isolation between the donor antenna and
service antenna. The Pico Repeater can activate AGC to set the Pico Repeater gain when
self-oscillation occurred.
UPLINK/DOWNLINK GAIN ADJUSTMENT SYNCHRONIZATION UPLINK ANDDOWNLINK GAIN SETUP AUTOMATICALLY
After the system is powered up, the input power is detected automatically and then the output power
is adjusted. After the downlink gain is calculated by the system, the uplink gain can be adjusted
equivalently. This method can balance the system amplification. The both path gain is adjusted
relevantly. The system gain is less than the system path loss. So the Pico Repeater will not bring any
interference and noise into the system link. One base station can hook up more than one Pico
Repeater.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
5/31
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
6/31
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
7/31
status graph, group management of repeater, authentication
(Admin/manager/user), support connecting with third party
software provider.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
8/31
5. PRODUCT DESCRIPTION
APPEARANCE
FIGURE 2 VIEW OF REPEATER
FIGURE 3 BUTTON VIEW OF REPEATER
System 1 is GSM900
GSM900 Alarm indicator
System and UL/DL
selection
Confirm setting
Power indicator
Gain setting
Battery Switch
Run indicator
Module indicator
Modem indicator
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
9/31
6. INSTALLATION INSTRUCTIONS
1) It supports wall mounting installation, follow the instructions below.
FIGURE 5 MOUNTING HOLE
1. First of all, choose a mounting position for the Pico Repeater in indoor environment. And
then align Pico Mounting hole on the wall and be marked
2. According to formerly marking on the wall to drill the holes, and inserted the rubber plug in
the holes.
3. Use screws fix the Picos mounting hole on the wall where Pico is going to be installed.
4. The BTS port on Pico Repeater is connected to the donor antenna, MS port is connected to
the service antenna.
5. System is supplied by AC100-240V power via connection of the external extension power
cable.
6. The system works properly under the condition of having enough system isolation.
7. With obstruction or no, it must ensure the distance of 5-30 m between the donor antenna
and service antenna.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
10/31
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
11/31
THE LED INDICATORS
The indicators on the front panel could be lightened are listed in the table below
Indicator Status
Power Indicator
Green light indicates that mian power supply is normal.LED off
indicates the main power is off
Module IndicatorGreen light indicates that main power or battery is normal; LED
off indicates the main power and battery are off
Run IndicatorFlashing green light indicates normal, if the LED is OFF,it means
the MCU of control panel fails.
Modem IndicatorThe indicator lights green while SIM card is being
inserted,signal is being recieved and data cable is disconnected to local
test port at the same time, otherwise indicator is off
System Indicator
Green light indicates that the system is
selected and can be read and set
UL/DL Indicator
Green light indicates that the UL(DL) band is selected
and can be read and set
Smart Function Indicator When the LED indicator is off, the Smart Function is OFF; It is inManual mode
When the LED indicator is green,the Smart Function is ON
Alarm Indicator When the indicator is green , it is in normal status.When the indicator is red, it means the AGC function is active or Pico
Repeater Self-Oscillation is occurring.
Be noted that users cant adjustparameters by manual setting when smart function is
activated (Pico can save data for GSM900 when you adjust it manually).Repeater must not be
powered on before the donor antenna and service antenna are connected.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
12/31
8. LOCAL SETUP STEPS
Connect your laptop to the repeater via the data cable. Do the following steps (the parameters listed in the
steps are mandatory to fill, remaining is defaulted or user defined):
a. Install the NMS-1.3.7, startup the Local Test Program (NMS-1.3.7), click on the Config Datatab,
choose the COM Parameters.
b. From the pop-up dialog, configure the Com Parameters, mark this check box and select
RS232,then click the Configbutton, choose the correct Com port from your PC,set Baudrateto
9600,and set the Timeoutto180.Then click the start button from tool bar.
Start
button
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
13/31
c. Right click the Site List, then choose New/ Area for create new area.
From pop-up dialog, Click the Create Button,the Area Code should be filled by any number with 2
digits,and input the Area Name,and then click on OK.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
14/31
d. Right click on the area name from Site List, then choose New/Site for create new Repeater.
From pop-up dialog, config the new site(repeater) properties as below: select Protocol 2G for
Protocol Type, select the 1.Windeband Repeaterfor the Main Equipment Type,the Site ID must
be filled by any number with 8 digits,and the Sub IDmust be 255, then click OK for save settings.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
15/31
After above steps, right click on the Repeater namefrom Site List, then select Local RS232for
Communicate Mode, and select the correct COM PortforSerial Port. And then click OK.
e. Right click on the Repeater namefrom Site List, and then select Get MOID.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
16/31
When Get MOID successfully, there will display as below Prompt: Get moid list successfully
f. After get MOID, you can pick up the parameters of repeater as below:
a) Query the Repeater Info, choose the Repeater Info page, click theAll button, then clickInquiry
button.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
17/31
b) Query the Monitor Info, choose the Monitor Info page, click theAll button, then clickInquiry
button.
You must set the Site IDsame as which site ID you set up to when built(NEW) site, and set Report
Phone No.1,SMS Center numberand Control Center Phone No.1 for remote monitoring system.
c) Query the Alarm Info, choose the Alarm Info page, click theAll button, then clickInquirybutton.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
18/31
d) Query the Alarm Enable, choose the Alarm Enable page, click theAll button, then clickInquiry
button.
If you need to disable alarm, you should tick the alarm which alarms need to be disabled, then double
click Local Valueand choose Disable. Then click Setbutton.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
19/31
e) Query and set the RF Parameters, choose the RF Para page, click theAll button, then click
Inquirybutton.And you can set the attenuation of Downlink and Uplink. Tick the DL Att&UL Att,
then double click the Local ValueofDL Att and UL Att, and then input 0 to 31 according
requirements (only after smart mode is disabled then can manually adjust ATT ). Double click the
Local ValueofOutput Signal Switch, select ONor OFF,then click Setbutton you can ON or OFF
the output power of pico repeater. In addition, you can turn ON or OFF the Smart function by
Switch of Smart, double click the Local Valueof Switch of Smart, select Onor Off, then click Set
button.
Note: When you set the parameters, please only tick the parameters which you need to be set.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
20/31
f) Query the RF Status, choose the RF Statues page, click theAll button, then clickInquirybutton,
main RF parameters are shown below, DL O/Pis the output power of repeater.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
21/31
9. NMS SETUP STEPS
Connect your laptop to the Modem via the data cable. Do the following steps:
a. Startup the NMS Test Program (NMS-1.3.7), Click on the Config Datatab, choose the COM Parameters.
b. From the pop-up dialog, configure the Com Parameters, mark this check box and select ShortMessage, then click the Configbutton, choose the correct Com port from your PC,set Baudrateto
9600,and set the Timeoutto180,click Save and OK button, then click the start button from tool bar.
Start
button
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
22/31
c. Right click the Site List, then choose New/ Area for create new area (If before the local software
has built the site, please start from step e)
From pop-up dialog,Click the Create Button,the Area Code should be filled by any number with 2
digits,and input the Area Name,and then click on OK.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
23/31
d. Right click on the area name from Site List, then choose New/Site for create new Repeater.
From pop-up dialog, config the new site(repeater) properties as below: select Protocol 2G for
Protocol Type, select the 1.Wideband Repeaterfor the Main Equipment Type, the Site ID must
be filled by any number with 8 digits(and must be set to the same value as the local setting ),and
the Sub ID must be 255, then click OK for saving settings.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
24/31
e) After above steps, right click on the Repeater namefrom Site List, input the NMS Mode Number
and Repeater Modem Number, then select Short Messagefor Communicate Mode, and select
the correct COM PortforSerial Port. And then click OK.
f.Right click on the
Repeater namefrom
Site List, and then select
Get MOID.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
25/31
When Get MOID successfully, there will display as below Prompt: Get moid list successfully
g. After get MOID, you can pick up the parameters of repeater as below:
a) Query the Repeater Info, choose the Repeater Info page, click theAll button, then clickInquiry
button.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
26/31
b. Query the Monitor Info, choose the Monitor Info page, click theAll button, then clickInquiry
button.
c. Query the Alarm Info, choose the Alarm Info page, click theAll button, then clickInquirybutton.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
27/31
d. Query the Alarm Enable, choose the Alarm Enable page, click theAll button, then clickInquiry
button.
If you need to disable alarm, you should tick the alarm which alarms need to be disabled, then double
click Local Valueand choose Disable. Then click Setbutton.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
28/31
e. Query and set the RF Parameters, choose the RF Para page, click theAll button, then click
Inquirybutton.And you can set the attenuation of Downlink and Uplink. Tick the DL Att&UL Att,
then double click the Local ValueofDL Att and UL Att, and then input 0 to 31 according
requirements (only after smart mode is disabled then can manually adjust ATT ). Double click the
Local ValueofOutput Signal Switch, select ONor OFF,then click Setbutton you can ON or OFF
the output power of pico repeater. In addition, you can turn ON or OFF the Smart function by
Switch of Smart, double click the Local Valueof Switch of Smart, select Onor Off, then click Set
button.
Note: When you set the parameters, please only tick the parameters which you need to be set.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
29/31
f. Query the RF Status, choose the RF Statues page, click theAll button, then clickInquirybutton,
main RF parameters are shown below, DL O/Pis the output power of repeater.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
30/31
10. SERVICE AFTER SALE
Your satisfaction is our priority. Offering a quick and effective technical support, we always put the
customer first. Please dont hesitate to contact us by the following ways if you have any questions.
-
8/10/2019 User Manual for GSM900 Band Selective Pico Repeater.pdf
31/31