Used with FILTERS Copyright © 2013 by The S.E.A. Group.

used with

FILTERS

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

CHECK:• Correct filter(s)• Filter(s) correctly fitted• Respirator clean,

complete, correctly assembled

Fit the SR200

• Loosen the side straps of the head harness. Twist the strap holders forward and pull on the strap.

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit the SR200

• Sling the neck strap around your neck

• Lift the head harness up over the mask and away from your face

• Place your chin in the chin cup

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit the SR200

• Pull the head harness backwards towards your neck

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit the SR200

• Tighten the side straps in pairs by pulling the loose ends

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit the SR200

• If necessary, adjust the two top straps. Undo buckles and pull loose ends forwards

• Fasten the buckles

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit the SR200

• Loose ends can be hooked to the head harness

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit the SR200

Fit a filter

• Screw the filter adapter into the mask

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit a filter• Make sure the filter is

turned the correct way (arrows toward mask)

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit a filter• Place filter in the filter

attachment• Ease the filter securely

into the groove

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit a filter

• Place a pre-filter in the pre-filter holder

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Fit a filter

• Snap the pre-filter onto the main filter

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Quick clean

• Use warm soapy water and a clean soft cloth, or a Sundström cleaning tissue

• Inspect and wipe the outside of the mask and visor

• You can leave the head harness on

• Check that there are no cracks or other damage

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Quick clean

• Use warm soapy water and a clean soft cloth, or a Sundström cleaning tissue

• Wipe the inside of the mask, including the visor

• Pay special attention to ‘nooks and crannies’ inside the respirator

• Make sure the face rims and chin cup are clean

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Quick clean

• Replace the pre-filter with a new one and snap onto the main filter

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Quick clean

• Store the assembled respirator in a sealed container away from any contaminants

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Thorough clean

• First, perform a quick clean

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Thorough clean

• Remove the filter and wipe the inside of the filter adapter

• Pay special attention to the groove and the rim of the filter adapter

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Thorough clean

• Remove each exhalation valve cap

• Gently pull the membrane out

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Thorough clean

• Carefully clean the membranes and the valve seats

• No dirt or grime must remain, and the parts must not have any cracks, tears or other damage

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Thorough clean

• Gently pull out the three inhalation membranes from inside the mask

• Clean all the membranes and the valve seats

• Replace the membranes

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Thorough clean

• If the head strap is very dirty or grimy, detach it and clean it separately

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Thorough clean

• Store the assembled respirator in a sealed container away from any contaminants

Copy

right

© 2

013

by T

he S

.E.A

. Gro

up

Used with FILTERS Copyright © 2013 by The S.E.A. Group.

Documents

Transcript of Used with FILTERS Copyright © 2013 by The S.E.A. Group.