U.S.C.G. Merchant Marine Exam Chief Engineer – Limited ... · Q604 Electrical-Electronic-Control...

National Maritime Center Serving Our Nation’s Mariners

U.S.C.G. Merchant Marine Exam

Chief Engineer – Limited

Q604 Electrical-Electronic-Control Engineering

(Sample Examination)

of 45 Q604 Electrical-Electronic-Control Engineering

8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27

Choose the best answer to the following Multiple Choice Questions.

1. In figure "B" of the illustrated circuit, if the resistance of R1 is 10 ohms, R2 is 10 ohms, and R3 is 10 ohms, what is the total resistance? Illustration EL-0032

• (A) 15 ohms o (B) 20 ohms o (C) 25 ohms o (D) 30 ohms

If choice A is selected set score to 1.

2. What is the maximum current allowed to be drawn from the secondary of a 2 kVA step-down transformer with a turns ratio of four to one if connected across a 440 volt line?

o (A) 1.1 amps o (B) 4.5 amps • (C) 18.1 amps o (D) 22.7 amps

If choice C is selected set score to 1.

3. As shown in figure "D" of the illustrated digital power meter, what type of single-phase load is under test for power measurement? Illustration EL-0256

o (A) a resistive-capacitive load • (B) an inductive-resistive load o (C) a purely resistive load o (D) a purely inductive load

If choice B is selected set score to 1.

4. As shown in figures "B" and "C" of the illustration, what should be the switch position and which test lead terminal jacks should be used if your intent is to measure AC currents anticipated as high as 5 amps? Illustration EL-0047

o (A) switch position "1" and terminal jacks "1 and 4" o (B) switch position "6" and terminal jacks "1 and 4" o (C) switch position "7" and terminal jacks "1 and 2" • (D) switch position "7" and terminal jacks "2 and 4"

If choice D is selected set score to 1.


8/21/2019


5. In testing a hand cranked megger prior to use, what statement is true?

o (A) With the test leads shorted or open, the pointer should go to infinite ohms. o (B) With the test leads shorted, the pointer should go to infinite ohms, and with the tests leads

open, the pointer should go to zero ohms. • (C) With the test leads shorted, the pointer should go to zero ohms, and with the tests leads

open, the pointer should go to infinite ohms. o (D) With the test leads shorted or open, the pointer should go to zero ohms.


6. Under what circumstance would a hand-held portable phase sequence indicator be used should the main switchboard mounted fixed phase sequence indicator be inoperative?

o (A) paralleling alternators • (B) preparing to make the shore power connection o (C) replacing a defective solenoid o (D) installing a new synchroscope


7. As shown in the illustration, what type of motor and motor starter are featured? Illustration EL-0137

o (A) reversing squirrel cage induction motor with reduced voltage autotransformer starting o (B) non-reversing squirrel cage induction motor with reduced voltage primary reactor starting • (C) non-reversing squirrel cage induction motor with reduced voltage autotransformer starting o (D) reversing squirrel cage induction motor with across-the-line starting


8. Which of the following describes the action when the handle is moved to the "start" position of a drum-type motor controller used with a compound wound DC motor?

o (A) Reduced voltage is supplied to the shunt field, series field, and armature. • (B) Full line voltage is supplied to the shunt field, and reduced voltage is supplied to the series

field and the armature. o (C) Full line voltage is supplied to the shunt and series fields, and reduced voltage is supplied to

the armature. o (D) Full line voltage is supplied to the shunt field, series field, and armature.



8/21/2019


9. By what means should motor controller contacts be routinely cleaned?

o (A) filing with a bastard file o (B) blowing with compressed air o (C) dressing with crocus cloth • (D) wiping with a clean dry cloth


10. Using the catalog selection chart shown in Illustration EL-0180, determine the correct catalog number for a motor starter that meets the following criteria: NEMA Open enclosure 3-pole Rated at 45 continuous amperes Vertically mounted Electronic overload relay-Ground fault feature set Reversing starter Operating coil rated at 24 VAC/60 Hz

o (A) AE19GNVB5G045 o (B) AN19AN0A5E005 • (C) AN59GNVT5G045 o (D) CN16GNVT5G045


11. As shown in the illustration, what mechanism will disconnect the motor from the line in case of a sustained motor overload? Illustration EL-0080

o (A) transformer secondary fuses FU6 and FU7 • (B) overload relay heaters and overload relay NC contacts (OL) o (C) disconnect switch fuses FU1, FU2, and FU3 o (D) transformer primary fuses FU4 and FU5


12. If a digital multimeter is set up as shown in figure "A" of the illustration to test an AC contactor coil, what would the display read if the coil is open-circuited? Illustration EL-0214

o (A) 0.03 ohms o (B) 22 ohms • (C) OL ohms o (D) 110 V



8/21/2019


13. As shown in the illustration, what is the purpose of the Time Delay (TR) coil in the circuit? Illustration EL-0104

• (A) Allows the motor to come up to speed at reduced voltage before bypassing the starting resistors.

o (B) Allows the motor to come up to speed before placing the starting resistors in the circuit. o (C) Ensures the motor cannot be started until the overload relays are reset. o (D) Ensures the motor cannot be started until the accelerating coil is energized.


14. As shown in figure "A" of the illustrated propulsion motor variable speed drive, what statement is true? Illustration EL-0140

o (A) both the bridge rectifier and the controller inverter bridge are transistor controlled in terms of switching

o (B) the bridge rectifier is uncontrolled and the controller inverter bridge is thyristor controlled in terms of switching

• (C) the bridge rectifier is uncontrolled and the controller inverter bridge is transistor controlled in terms of switching

o (D) both the bridge rectifier and the controller inverter bridge are thyristor controlled in terms of switching


15. Which of the following is a disadvantage of electric drive propulsion systems?

o (A) The propeller speed and direction of rotation are easily controllable. o (B) Main propulsion power may also be directed to ships electrical service distribution. • (C) Propulsion motors are required along with electrical power generation machinery. o (D) Location of electric power generation machinery is flexible.


16. As shown in figure "B" of the illustration, what statement is true concerning "regenerating" operation? Illustration EL-0162

o (A) by applying torque in the opposite direction of rotation direction, the motor briefly regenerates power back into the mains, which rapidly speeds up the motor

o (B) by applying torque in the same direction of rotation direction, the motor briefly regenerates power back into the mains, which rapidly slows down the motor

• (C) by applying torque in the opposite direction of rotation direction, the motor briefly regenerates power back into the mains, which rapidly slows down the motor

o (D) by applying torque in the same direction of rotation direction, the motor briefly regenerates power back into the mains, which rapidly speeds up the motor



8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27 17. How is the direction of rotation of the main propulsion motor in a modern AC propulsion drive system

reversed?

o (A) reversing the direction of current flow in the armature o (B) changing the direction of current flow in the motor's field winding • (C) electronically changing the phase sequence of the voltages generated by the power converter o (D) power directional relays


18. By what common means is the speed of the AC propulsion motor on a diesel-electric propulsion ship controlled?

o (A) by increasing the current to the motor o (B) by increasing the motor voltage o (C) by decreasing the motor voltage • (D) by varying the input frequency of the voltage to the motor


19. Referring to the illustration of a twin-screw diesel-electric AC propulsion drive system, what is the purpose of the shaft position signal? Illustration EL-0168

o (A) The shaft position signal senses shaft vibration due to shaft bearing wear or propeller blade damage and provides data for the predictive maintenance system.

o (B) The shaft position signal is used when changing the direction of rotation of the shaft and is used to determine the exact instant reversal of rotation takes place after reversing torque direction.

• (C) The shaft position signal is used when in the shaft-synchronizing mode to momentarily accelerate or decelerate the shafts to align the propeller blades of the two shafts to reduce vibration.

o (D) The shaft position signal detects axial movement of the shaft due to thrust bearing wear and provides data for the predictive maintenance system.


20. Propulsion AC generators creating 4160 VAC use transformers to provide nominally 120 VAC to the automatic voltage regulator. What is the turns ratio of this step-down transformer?

o (A) 1:4 o (B) 4:1 • (C) 35:1 o (D) 40:1



8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27 21. An AC diesel-electric drive ship with synchronous propulsion motors has the capability for power

factor correction. If the power factor associated with the main power distribution including all motors is 0.7 leading, what statement is true?

o (A) The synchronous propulsion motors are normally excited. o (B) The synchronous propulsion motors are under-excited. o (C) The excitation status of the synchronous motor cannot be determined. • (D) The synchronous propulsion motors are over-excited.


22. In addition to improper brush pressure or seating, what can result in excessive sparking at the brushes of a DC propulsion motor?

o (A) operating at continuously varying loads such as during maneuvering o (B) reversed main field polarity with respect to the armature • (C) improper positioning of brush rigging outside the neutral plane o (D) reversed armature polarity with respect to the field


23. What type of motor is generally used in DC propulsion drive systems?

o (A) differentially compounded o (B) permanent magnet • (C) shunt wound o (D) series wound


24. How is reversal of a DC propulsion motor achieved?

• (A) reversing the direction of current flow in the motor field windings o (B) the use of a 12 pulse converter o (C) reversing the phase sequence of the incoming voltage o (D) the use of a shunt field regulator


25. How is speed control of a DC propulsion motor accomplished?

o (A) the use of a load-commutated inverter o (B) adjusting the output frequency of the electric power source o (C) the use of static power converters • (D) adjusting the input voltage to the motor



8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27 26. What equipment for modern SCR rectified DC propulsion drive systems is usually included in the

package?

o (A) propulsion generators which produce DC power that is converted to AC power for the propulsion motor

o (B) propulsion generators which produce DC power that is directly delivered to the series wound DC propulsion motor

o (C) propulsion generators which produce AC power that is directly delivered to the synchronous AC propulsion motor

• (D) propulsion generators which produce AC power that is converted to DC power for the shunt wound DC propulsion motor


27. On an older two-generator, two-motor DC diesel-electric drive system as shown in the illustration, if both the A1 and A2 contactors are dropped out, both the S1 and S2 contactors are dropped out, and both the G1 and G2 contactors are pulled in, what is the configuration of the plant? Illustration EL-0141

• (A) The main propulsion generators provide power to the main propulsion motors, and the gas turbine generator provides power to the bow thruster motor as needed.

o (B) The gas turbine generator provides power to the main propulsion motors, and the auxiliary diesel-generator provides power to the bow thruster motor as needed.

o (C) The gas turbine generator provides power to the main propulsion motors and provides power to the bow thruster motor as needed.

o (D) The main propulsion generators provide power to the main propulsion motors, and the auxiliary diesel-generator provides power to the bow thruster motor as needed.


28. Refer to the two-generator, two-motor, DC diesel-electric drive propulsion system simplified schematic shown in the illustration. While in two-generator, two-motor operation, which of the following conditions would cause the propulsion shaft speed to be approximately one-half the desired speed? Illustration EL-0141

o (A) The field winding of one of the propulsion motors is open-circuited. o (B) The armature winding of one of the propulsion generators is open-circuited. • (C) The field winding of one of the propulsion generators is open-circuited. o (D) The armature winding of one of the propulsion motors is open-circuited.



8/21/2019


29. As shown in the illustration of a DC diesel-electric propulsion drive system, what would be the set up contactor configurations if #1 M/E is to be secured, so that only #2 M/E diesel-generator is set up to supply both propulsion motors? Illustration EL-0141

• (A) contactors G2 and S1 pulled in; contactors G1 and S2 dropped out o (B) contactors G2 and S2 dropped out; contactors G1 and S1 pulled in o (C) contactors G2 and S2 pulled in; contactors G1 and S1 dropped out o (D) contactors G2 and S1 dropped out; contactors G1 and S2 pulled in


30. Due to the operating characteristics of the system, time lag fuses (or dual-element fuses) are necessary for use in what types of circuits?

• (A) motor starting circuits o (B) general alarm circuits o (C) emergency lighting circuits o (D) main lighting circuits


31. When the operating handle of a molded-case circuit breaker is in the mid-position, what does this indicate?

• (A) the circuit breaker has tripped o (B) the circuit breaker is switched on o (C) the circuit breaker is switched off o (D) the circuit breaker has been reset


32. What is the greatest single cause of electrical failures?

• (A) the breakdown of insulation o (B) too frequent testing o (C) overcurrent o (D) high inductance


33. What type of circuit is represented by the diagram shown in the illustration? Illustration EL-0058

o (A) dual speed, 2-winding motor controller circuit o (B) common fluorescent lighting circuit o (C) uninterruptible power supply circuit • (D) navigation running light circuit



8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27 34. What are the operating characteristics of a step-down potential transformer in terms of the

secondary load?

o (A) reduced power (kVA) • (B) reduced voltage and increased current o (C) reduced current and increased voltage o (D) reduced voltage and reduced current


35. What is the purpose of the device labeled "Man-Auto Sw." in the illustrated switchboard? Illustration EL-0003

o (A) to shift the governor control from manual to automatic/zero droop or vice versa o (B) to enable the operator to read the field voltage on device "Volt. Reg. Adj. Pot." or device

"Man. Volt. Adj. Rheo." o (C) to supply regulated control power to the switchboard • (D) to shift from the automatic voltage regulator to manual voltage control or vice versa


36. As shown in figure "A" of the illustration, with respect to the common equipment grounding conductor, what statement is true? Illustration EL-0125

o (A) The common equipment grounding conductor is solidly-grounded at the source and this is the least common arrangement onboard merchant vessels.

o (B) The common equipment grounding conductor is insulated from the source and this is the least common arrangement onboard merchant vessels.

o (C) The common equipment grounding conductor is solidly-grounded at the source and this is the most common arrangement onboard merchant vessels.

• (D) The common equipment grounding conductor is insulated from the source and this is the most common arrangement onboard merchant vessels.


37. Why is it necessary to perform periodic testing of correctly rated and properly installed circuit breakers?

• (A) to insure they will continue to provide the original degree of protection o (B) to insure they do not exceed their interrupting capacity o (C) to insure they can trip faster as they increase in age o (D) to insure they will be able to withstand at least 125% of applied voltage



8/21/2019


38. Which of the following procedures should be used to maintain a large electric motor during periods of inactivity?

o (A) A thin layer of air-drying varnish should be applied on the windings. • (B) Space heaters should be used to prevent condensation of moisture. o (C) Spraying a solvent periodically to remove carbon dust. o (D) Compressed air should be blown over areas where dust is deposited.


39. To check the three line fuses protecting a three-phase motor using a multimeter set up as a voltmeter, what should be done FIRST?

o (A) make sure the motor is operating at full load to guard against a false reading o (B) place the leads across the bottom ends of the fuses o (C) place the leads across the "hot" ends of the fuses • (D) place the starter in the "stop" position


40. If a digital multimeter is set up as shown in figure "A" of the illustration, what would be displayed on the screen if the fuse being tested is blown? Illustration EL-0210

o (A) OL volts o (B) 0.001 ohms o (C) 470 ohms • (D) OL ohms


41. In the lighting distribution circuit shown in the illustrated lighting panel L110 of the illustration, if all circuit breakers are closed and due to a problem with the relevant feeder circuit breaker, there is a loss of power on the incoming phase A, which of the following statements is true? EL-0013

o (A) Half of the passageway lighting circuits on the 01 deck would lose power. o (B) All of the accommodation lighting circuits on the 01 deck, starboard side would lose power. o (C) All of the receptacles in the laundry would lose power. • (D) Half of the accommodation lighting circuits on the 01 deck, port side would lose power.


42. What does section "C" of the circuit shown in the illustration function as? Illustration EL-0085

o (A) a voltage regulator • (B) a filter o (C) a rectifier o (D) a voltage transformer



8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27 43. As shown in figure "A" of the illustration, what type of converter unit is represented? Illustration EL-

0240

o (A) de-multiplexer o (B) multiplexer • (C) analog to digital converter o (D) digital to analog converter


44. What is the name of the digital logic gate represented by figure "1" of the illustration? Illustration EL-0035

o (A) NOR gate o (B) Exclusive OR gate o (C) AND gate • (D) OR gate


45. In process control terminology, continuously variable values which change without distinct increments, such as temperature, pressure, or level are correctly referred to as what type of values?

o (A) bumpless values o (B) digital values • (C) analog values o (D) binary values


46. As shown in figures "A", "B", and "C" of the illustration, what is the purpose of the differential amplifier segment of the 741 operational amplifier? Illustration EL-0111

o (A) detect and amplify the voltage difference between the inputs at pins 1 and 2 o (B) detect and amplify the voltage difference between the inputs at pins 1 and 5 • (C) detect and amplify the voltage difference between the inputs at pins 2 and 3 o (D) detect and amplify the voltage difference between the inputs at pins 3 and 5


47. Which of the listed conditions describes the effect on intrinsic semiconductor operation as a result of a temperature increase?

o (A) Inductive reactance will decrease • (B) Conductivity will increase o (C) Capacitive reactance will decrease o (D) Resistivity will increase



8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27 48. As shown in figure "A" of the illustration, what is true concerning the illustrated frequency response

curve? Illustration EL-0076

o (A) Low frequencies below the cutoff-frequency are attenuated and high frequencies above the cutoff-frequency are attenuated.

o (B) Low frequencies below the cutoff-frequency are attenuated and high frequencies above the cutoff-frequency are passed.

• (C) Low frequencies below the cutoff-frequency are passed and high frequencies above the cutoff-frequency are attenuated.

o (D) Low frequencies below the cutoff-frequency are passed and high frequencies above the cutoff-frequency are passed.


49. What is the functional purpose of a heat sink, as frequently used with transistors?

o (A) to compensate for excessive doping o (B) to decrease the forward current • (C) to prevent excessive temperature rise o (D) to increase the reverse current


50. What would be the resistance tolerance of a carbon resistor which is color-coded as red, violet, brown, and silver in bands 1 thru 4 respectfully as shown in figure "A" of the illustration? Illustration EL-0103

o (A) 1% o (B) 5% • (C) 10% o (D) 20%


51. If a digital multimeter is set up as shown in figure "B" of the illustration to test a capacitor, what would the display read if the capacitor was functioning properly? Illustration EL-0213

o (A) the charging voltage would be displayed which will initially be low and gradually rise to the internal battery voltage

o (B) initially a very high ohmic value will be displayed (OL ohms), followed by a gradual drop in resistance until a very low value is displayed

o (C) initially a very low ohmic value will be displayed, followed by a gradual rise in resistance until a very high value is displayed (OL ohms)

• (D) the actual capacitance value of the capacitor will be displayed which should be within the tolerance range of the capacitor



8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27 52. An ohmmeter used to test for front-to-back resistance of a PN junction diode should produce roughly

what ratio?

• (A) 100:1 o (B) 500:1 o (C) 1000:1 o (D) 5000:1


53. What should be done with a capacitor that is obviously discolored due to excessive heat?

o (A) cooled with a spray can of refrigerant approved for this purpose o (B) calibrated using a capacitance Wheatstone bridge o (C) resoldered with care taken to ensure that the original cold solder joint is repaired • (D) replaced and the reason for the overheating found


54. When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. What condition does this indicate?

o (A) good capacitive quality o (B) an open o (C) good resistive quality • (D) a short


55. What problem with a printed circuit board may resolve itself once a board is removed from its edge card connector and then reinstalled?

o (A) Discolored or darkened components o (B) Leaking components • (C) Corroded pin connectors o (D) Open traces or broken connections



8/21/2019


56. When troubleshooting a printed circuit board, one technique that can be used is swapping the suspected damaged board with a new board. When installing the new board which was stored in a specially manufactured antistatic bag, how may damage due to electrostatic discharge be prevented?

o (A) Before touching the board, you should discharge any static buildup on yourself by touching a conductive surface or use a grounding wrist strap, and the board should be handled by grasping trace solder surfaces.

• (B) Before touching the board, you should discharge any static buildup on yourself by touching a conductive surface or use a grounding wrist strap, and the board should be handled by its insulated edges only.

o (C) Before touching the board, you should discharge any static buildup on the board by touching the board to a conductive surface, and the board should be handled by grasping trace solder surfaces.

o (D) Before touching the board, you should discharge any static buildup on the board by touching the board to a conductive surface, and the board should be handled by its insulated edges only.


57. Some shipboard high voltage systems have the neutral point of the generators bonded to the ship's hull with a neutral grounding resistor. What is the purpose of this resistor?

o (A) To completely eliminate ground fault current • (B) To minimize the magnitude of the ground fault current o (C) To prevent nuisance ground fault trips o (D) To maximize the magnitude of the ground fault current


58. For the purposes of shipboard practice, voltages above what threshold would be considered high voltage?

o (A) 440 VAC • (B) 1000 VAC o (C) 4160 VAC o (D) 6600 VAC


59. According to the liquid crystal data display for the depth sounder shown in the illustration, what is the instantaneous depth currently being displayed? Illustration EL-0186

o (A) 43.5 meters below the surface o (B) 43.5 meters below the transducer o (C) 47.5 meters below the surface • (D) 47.5 meters below the transducer



8/21/2019

Q604 Electrical-Electronic-Control Engineering U.S.C.G. Merchant Marine Exam Chief Engineer-Limited Illustrations: 27 60. As shown in the illustrated block diagram for a digitized echo sounding system, what statement is

true concerning the function of the transducer? Illustration EL-0185

o (A) The transducer converts radio frequency (RF) electromagnetic energy to acoustical energy while receiving and converts the reflected acoustical energy back into RF electromagnetic energy while transmitting.

• (B) The transducer converts radio frequency (RF) electromagnetic energy to acoustical energy while transmitting and converts the reflected acoustical energy back into RF electromagnetic energy while receiving.

o (C) The transducer converts audio frequency (AF) electromagnetic energy to acoustical energy while receiving and converts the reflected acoustical energy back into AF electromagnetic energy while transmitting.

o (D) The transducer converts audio frequency (AF) electromagnetic energy to acoustical energy while transmitting and converts the reflected acoustical energy back into AF electromagnetic energy while receiving.


61. As shown in the illustrated adaptive digital steering control system functional block diagram and listed system interface signals table, what would the rudder order signal output voltage to the rudder servo amplifier be for a rudder order of 15 degrees right rudder, assuming left rudder signals are negative and right order signals are positive in polarity? Illustration EL-0191

o (A) -1.33 VDC o (B) -3.75 VDC • (C) +3.75 VDC o (D) +5.0 VDC


62. As shown in the illustrated adaptive digital steering control system functional block diagram and listed system interface signals table, what would the rudder order signal output voltage to the rudder servo amplifier be for a rudder order of 20 degrees left rudder, assuming left rudder signals are negative and right order signals are positive in polarity? Illustration EL-0191

o (A) -2.25 VDC o (B) -4.0 VDC • (C) -5.0 VDC o (D) +5.0 VDC


63. What statement is true concerning random access memory (RAM)?

o (A) RAM is non-volatile memory and the contents of RAM are lost when the power is removed. o (B) RAM is non-volatile memory and the contents of RAM are not lost when the power is

removed. • (C) RAM is volatile memory and the contents of RAM are lost when the power is removed. o (D) RAM is volatile memory and the contents of RAM are not lost when the power is removed.



8/21/2019


64. What Ethernet cabling technology supports the greatest data transfer speeds?

o (A) Thick Ethernet• (B) Gigabit Etherneto (C) Thin Etherneto (D) Fast Ethernet


65. If a computer display is flickering, how may this be remedied?

o (A) Increase the resolution bandwidtho (B) Decrease the resolution bandwidth• (C) Increase the refresh rateo (D) Decrease the refresh rate


66. A very useful Windows utility for discovering or verifying IP addressing information of a network is"ipconfig". How is this utility program launched?

o (A) It is run by clicking on the "ipconfig" icon in start menu or under programs.o (B) It is run from the command prompt screen by default by simply bringing up the command

prompt.• (C) It is run from the command prompt screen by typing "ipconfig/all".o (D) It is run by clicking on the TCP/IP shortcut icon on the desktop.


67. In order for a live-line tester to be used to test and prove dead a high voltage circuit, what must bedone to verify the ability of the tester to detect a voltage?

• (A) The live-line tester should be checked by connecting to a known high voltage source beforeand after the circuit to be worked upon is tested.

o (B) The live-line tester need not be checked prior to testing the circuit to be worked upon as longas it has not been declared inoperative.

o (C) The live-line tester should be checked by connecting to a known high voltage source onlyafter testing the circuit to be worked upon.

o (D) The live-line tester should be checked by connecting to a known high voltage source onlybefore testing the circuit to be worked upon.



8/21/2019


68. When a high voltage system insulation test value is suspect or recorded during an annual survey, apolarization index test is performed. What is the polarization index?

o (A) The polarization index is the ratio of the insulation resistance taken at thirty minutes to theinsulation resistance taken at one minute.

• (B) The polarization index is the ratio of the insulation resistance taken at ten minutes to theinsulation resistance taken at one minute.

o (C) The polarization index is the insulation resistance taken at ten minutes.o (D) The polarization index is the ratio of the insulation resistance taken at one minute to the

insulation resistance taken at ten minutes.


69. Overheating is suspected in a high voltage bolted bus-bar joint. If the local continuity resistance is tobe checked off-line after the necessary safety precautions have been taken, what instrument wouldbe used for the resistance test?

o (A) A special high resistance tester (megohmmeter).• (B) A special low resistance tester (microhmmeter).o (C) A conventional ohmmeter.o (D) Any of the above ohmmeters would be suitable.


70. How should the shunt used in an ammeter be connected?

• (A) in series with the load and in parallel with the meter movemento (B) in parallel with the load and in parallel with the meter movemento (C) in series with the load and in series with the meter movemento (D) in parallel with the load and in series with the meter movement



8/21/2019

National Maritime Center

Serving Our Nation’s Mariners

10/5/2018

EL-0003

Adapted for testing purposes only from HUBERT, Operating, Testing and Preventive

Maintenance of Electrical Power Apparatus.

Copyright © 2003 Pearson Education

Further reproduction prohibited without permission of 45 Q604 Electrical-Electronic-Control Engineering



10/5/2018

EL-0013

Adapted for testing purposes only from HUNT, Modern Marine Engineer’s Manual,

Volume II, Third Edition

Copyright © 2002 by Cornell Maritime Press, Inc.




10/5/2018

EL-0032

Adapted for testing purposes only from GROB, Basic Electronics, Fourth Edition

Copyright © 1977 by McGraw-Hill, Inc.

Further reproduction prohibited without permission




10/5/2018

EL-0035

Adapted for testing purposes only from HERMAN, Industrial Motor Control, 6th Edition

Copyright © 2010 by Delmar, Cengage Learning





10/5/2018

EL-0047

Adapted for testing purposes only from MAZUR, Digital Multimeter Principles, Third Edition

Copyright © 2006 by American Technical Publishers, Inc.

Further reproduction prohibited without permission of 45




10/5/2018

EL-0058

Adapted for testing purposes only





10/5/2018

EL-0076

Adapted for testing purposes only from KILIAN, Modern Control Technology, 3rd Edition






10/5/2018

EL-0080

Adapted for testing purposes only from HALL, Practical Marine Electrical Knowledge, 2nd Edition

Copyright © 2003 by Dennis T. Hall





10/5/2018

EL-0085

Adapted for testing purposes only from Introduction to Solid-State Devices and

Power Supplies Training Series, Module 7

NAVEDTRA 14179





10/9/2018

EL-0103






10/9/2018

EL-0104

Adapted for testing purposes only from ROCKIS, Electrical Motor Controls

for Integrated Systems, 4th Edition

Copyright © 2009 by American Technical Publishers, Inc.





10/9/2018

EL-0111

Adapted for testing purposes only from Introduction to Amplifiers,

Navy Electricity and Electronics Training Series, Module 8

NAVEDTRA 172-08-00-82





10/9/2018

EL-0125


Maintenance of Electrical Power Apparatus

Copyright © 2003 Pearson Education Further reproduction prohibited without permission of 45




10/9/2018

EL-0140

Adapted for testing purposes only from HALL, Practical Marine Electrical Knowledge, 3rd Edition






10/10/2018

EL-0168

Adapted for testing purposes only from HALL, Practical Marine Electrical Knowledge, 3rd Edition





10/10/2018

EL-0180 Catalog Number Selection Chart

Adapted for testing purposes only Further reproduction prohibited without permission




10/10/2018

EL-0185 Digitized Echo Sounding System

Adapted for testing purposes only from

Furuno Electric Co. Further reproduction prohibited without permission




10/10/2018

EL-0210






10/11/2018

EL-0213






10/11/2018

EL-0214






10/11/2018

EL-0240

Adapted for testing purposes only from KIILIAN, Modern Control Technology, 3rd edition




U.S.C.G. Merchant Marine Exam Chief Engineer – Limited ... · Q604 Electrical-Electronic-Control...

Documents

Transcript of U.S.C.G. Merchant Marine Exam Chief Engineer – Limited ... · Q604 Electrical-Electronic-Control...

U.S.C.G. Merchant Marine Exam Mate Offshore Supply Vessels ... · Q209 Deck General U.S.C.G. Merchant Marine Exam Mate Offshore Supply Vessels Illustrations: 3 . 16. Your ship has

U.S.C.G. Merchant Marine Exam DDE – 1000/4000 HP Q634 ...€¦ · National Maritime Center Serving Our Nation’s Mariners. U.S.C.G. Merchant Marine Exam . DDE – 1000/4000 HP

U.S.C.G. Merchant Marine Exam Apprentice Mate Steersman ...€¦ · Q412 Navigation General-Near Coastal U.S.C.G. Merchant Marine Exam Apprentice Mate Steersman Illustrations: 3 .

U.S.C.G. Merchant Marine Exam Assistant Engineer – Limited ...Q612 Gas Turbine Plants U.S.C.G. Merchant Marine Exam Assistant Engineer-Limited Illustrations: 8 . 10. Thermal energy

U.S.C.G. Merchant Marine Exam Assistant Engineer – MODU …€¦ · U.S.C.G. Merchant Marine Exam Assistant Engineer-MODU Illustrations: 10 . Choose the best answer to the following

U.S.C.G. Merchant Marine Exam Chief Engineer – UFIV Q694 ...

U.S.C.G. Merchant Marine Exam Operator Uninspected ......U.S.C.G. Merchant Marine Exam Operator Uninspected Passenger Vessel Near Coastal Illustrations: 2 . 11. Which knot in illustration

U.S.C.G. Merchant Marine Exam Mate of Unlimited Tonnage ... · Q310 Nav General-Great Lakes and Inland U.S.C.G. Merchant Marine Exam Mate of Unlimited Tonnage Illustrations: 0 . 24.

U.S.C.G. Merchant Marine Exam Master Near Coastal Less ......Q160 Deck General U.S.C.G. Merchant Marine Exam Master Near Coastal Less than 100 Gross Registered Tons Illustrations:

U.S.C.G. Merchant Marine Exam DDE – Unlimited HP Q620 Motor … · 2019-09-11 · Q620 Motor Plants U.S.C.G. Merchant Marine Exam DDE - Unlimited HP Illustrations: 28 . 10. The

U.S.C.G. Merchant Marine Exam Second/Third Mate of ...Q114 Navigation General-Oceans U.S.C.G. Merchant Marine Exam Second/Third Mate of Unlimited Tonnage Illustrations: 2 . 6. You

U.S.C.G. Merchant Marine Exam Mobile Offshore Drilling ... · U.S.C.G. Merchant Marine Exam Mobile Offshore Drilling Units Illustrations: 0 . 5. Prior to getting underway, the Master

U.S.C.G. Merchant Marine Exam DDE – Unlimited HP Q622 ...€¦ · Q622 Gas Turbine Plants U.S.C.G. Merchant Marine Exam DDE-Unlimited HP Illustrations: 7 . 10. Thermal energy is

U.S.C.G. Merchant Marine Exam QMED Q808 Pumpman …Q808 Pumpman U.S.C.G. Merchant Marine Exam QMED Illustrations: 10 . Choose the best answer to the following Multiple Choice Questions.

U.S.C.G. Merchant Marine Exam Chief Engineer-MODU ......Q740 Engineering Safety-Environmental Protection U.S.C.G. Merchant Marine Exam Chief Engineer-MODU Illustrations: 5 6. Sea water

U.S.C.G. Merchant Marine Exam Third Assistant Engineer ... · U.S.C.G. Merchant Marine Exam Third Assistant Engineer Q531 Motor Plants I Illustrations: 21 . 6. Which of the following

U.S.C.G. Merchant Marine Exam Assistant Engineer – OSV ... · Q654 Electrical-Electronics-Control Engineering U.S.C.G. Merchant Marine Exam Assistant Engineer-OSV Illustrations:

U.S.C.G. Merchant Marine Exam Second/Third Mate of ...

U.S.C.G. Merchant Marine Exam Master Less than 200 Gross ...

U.S.C.G. Merchant Marine Exam Apprentice Mate Steersman ... · Q413 Navigation General-Oceans U.S.C.G. Merchant Marine Exam Apprentice Mate Steersman Illustrations: 4 . 5. You are