UNT Chemical Hygiene Plan · 2018. 12. 3. · UNT Overnight Experiment Notice Form Laboratory...

Chemical Hygiene PlanTable of Contents

IntroductionPolicy statementBackgroundLaboratory Definition

Hazard Identification and EvaluationCriteria for Control MeasuresChemical InventorySafety Data Sheets (SDS)Labeling

Standard Operating ProceduresLaboratory Safety OfficersBasic Rules for Non-Laboratory Personnel In LaboratoriesGeneral Laboratory RulesRules for Safe Laboratory Work

Control Measures ImplementationChemical StorageEngineering ControlsPersonal Protective EquipmentExposure Levels and Medical Monitoring

NanoparticlesTrainingContaminated Waste Removal/Disposal

General Methods for Segregation and DisposalHazardous WasteRadioactive Waste

RMS Standard Operating Procedures (SOP)Revision

Appendices

Appendix A - Definition of a Carcinogen and List of Known Human CarcinogensAppendix B - Overnight Experiment Notice FormAppendix C - List of Incompatible ChemicalsAppendix D - Maximum Allowable Container Capacities Stored Outside a Flammable CabinetAppendix E - Acutely Toxic ChemicalsAppendix F - DEA Schedules of Controlled SubstancesAppendix G - Glassware Used For Drug MakingAppendix H - DHS Chemicals of InterestAppendix I - Laboratory Safety Rules and Best PracticesAppendix J - Self-Assessment TrainingAppendix K - Use and Storage of Laboratory CylindersAppendix L - Laboratory Incident Reporting Procedures

Forms

UNT Overnight Experiment Notice Form

Laboratory Incident Report Form

Introduction

Policy statementThe University of North Texas recognizes its legal and social obligations to provide a safe working environment and believes students, faculty,and staff have a right to know about health hazards associated with their work. This manual includes responsibilities, policies and proceduresdesigned to develop an awareness of potentially hazardous chemicals in a laboratory and to promote safe laboratory practices.

The University of North Texas assumes the responsibility for laboratory safety. Students and employees will obtain access to pertinent safetyinformation through their supervisory staff or the departmental Laboratory Safety Officer. When safety concerns arise, students are encouraged tocontact their instructor. An important aspect of the Chemical Hygiene Plan is that once a person is given the basic training and information, theywill take every effort to protect themselves.

The eventual success of this safety and health program is a result of the joint efforts and responsibility of the laboratory students, instructors andthe administration of UNT. The University places a high priority on the establishment of safe and healthful learning environment through the

1. 2.

3. 4. 5. 6. 7. 8. 9.

leadership and participation of all members of the organization.

BackgroundThe Occupational Safety and Health Administration (OSHA) promulgated the Laboratory Standard, 29CFR 1910.1450, Occupational Exposuresto Hazardous Chemicals in Laboratories. The standard mandates that any laboratory, or organization of laboratories, which handle hazardouschemicals will prepare and implement a chemical hygiene plan.

This Chemical Hygiene Plan meets the standards set by OSHA. This guide includes specific measures taken to ensure personal protection andincludes the following elements:

Standard Operating Procedures relevant to safety and health considerations;Provisions for hazard identification and evaluation, including the criteria used to determine and implement control measures such asengineering controls and personal protective equipment;Requirements for the proper functioning of laboratory fume hoods and other protective equipment;Provisions for training and information;Provisions for medical consultation and examination;Designation of personnel responsible for implementation;Procedures for hazardous waste disposal;Procedures for spills;Procedures for record maintenance.

Laboratory DefinitionIn , a laboratory is defined as:29 CFR 1910.1450

Laboratory means a facility where the "laboratory use of hazardous chemicals" occurs. It is a workplace where relatively smallquantities of hazardous chemicals are used on a non-production basis.

For the purposes of this document, the following definition of laboratory will apply:

A room or space (to include closets and support chaseways) provided for instructional, observation, measurement or otherresearch activities that includes chemical, biological and/or radiological materials, or contains physical or mechanical equipment,in a non-production environment.

Categories of laboratories covered under this definition include:

ArtBiologicalChemicalEnvironmentalEngineeringPhysical

Back to Top

Hazard Identification and Evaluation

Criteria for Control Measures

Evaluating whether special handling precautions are warranted will require examination of a number of factors in order to formulate handlingrecommendations, including:

Potential for routine airborne exposure.Potential for routine dermal exposure.Potential for accidental exposure.Quantities of chemicals processed.Composition of mixtures containing special hazards.Previous history of accidents or illnesses in the area.Physical and chemical properties of the chemical.

Proposals must be submitted to RMS for approval prior to starting any experiments using or producing highly toxic, flammable,explosive or otherwise potentially dangerous conditions.

1. 2. 3.

1.

Exposure controls currently utilized.Chemical stability of the chemical.Available toxicological and health effect data.

Based on the results of the hazard evaluation, recommendations for special handling requirements could include:

Application of written standard operating procedures (required for especially hazardous substances, e.g., explosives, flammables, et al.);Training that must be completed prior to assigning any tasks.Establishment of designated handling areas.Posting of warning signage.Exposure monitoring requirements.Use of laboratory fume hoods or local exhaust.Prior fit testing and instruction in the proper use of respiratory protection equipment (contact Risk Management Services, (940) 565-2109for more information).Special hygiene requirements.Use of protective clothing.Decontamination procedures.Procedures for removal of contaminated material.Proper method for hazardous waste removal. Contact Risk Management Services to .request a hazardous waste pickup

Chemical InventoryA chemical inventory is conducted annually that lists all hazardous chemicals in laboratories. Chemicals listed are those classified as hazardousby:

Department of Transportation (DOT);Environmental Protection Agency (EPA);Occupational Health and Safety Administration (OSHA); ordisplaying a 3 or greater number in any section of the National Fire Protection Association (NFPA) diamond; orlisted in Schedules I through V in the DEA list of Controlled Substances (See for the list of Controlled Chemicals).Appendix F

DOT and EPA classifications as listed in their respective literature, or listed in Schedules I through V in the DEA list of Controlled Substances(See for the list of Controlled Chemicals and for the list of Glassware Used in Drug Making). The Standard recommendsAppendix F Appendix Gthat reproductive toxins, highly toxic materials and carcinogens be identified and listed on an additional chemical inventory for highly toxicmaterials and carcinogens.

Chemicals are listed alphabetically, according to the product name. The chemical name, manufacturer, and amount in storage are listed . Appendi includes chemicals of interest and screening threshold quantities (STQ) from Homeland Security Department. Any chemicals exceeding thex H

STQ quantities must be reported for security issues.

Safety Data Sheets (SDS)Safety Data Sheets ( s) are supplied by the chemical manufacturer and provide information regarding the product's physical, chemical andSDStoxicological characteristics, methods for safe handling, storage and disposal, and personal protective measures for contact and spills.

Hazard evaluation relies on the chemical manufacturer's provided information to ascertain whether or not the chemical is hazardous. Orders forchemicals shall include a request for the product SDS.

Labeling29 CFR 1910.1450 contains specific chemical labeling requirements. Labeling is required for all hazardous chemicals that are manufactured,shipped and used in the workplace. The manufacturer's labels must not be removed or defaced.

Chemical manufacturers, importers, and distributors are required to label each container of hazardous chemical leaving their facility with thefollowing information:

Identity of the hazardous chemicalAppropriate hazard warningsName and address of the manufacturer

Each chemical transferred outside of the laboratory that is not in its original container must also be labeled. These workplace labels must containSDS information as follows:

The master binders containing SDSs are kept in office 117 in the Risk Management Services (RMS) offices located at 700 North Individual departments may wish to maintain their own SDS collection.Texas Blvd., Denton, Tx 76201.

1. 2. 3. 4. 5.

Identity of the hazardous chemicalRoute of entry (e.g. eyes, nose, ingestion, or skin)Health hazardPhysical hazardTarget organ affected

An example of an in-house label is shown below:

Acetic Acid

Route of Entry Eyes, Skin, Nose

Health Hazard Poison

Physical Hazard Corrosive

Target Organs Skin and Lungs

Back to Top

Standard Operating Procedures

Laboratory Safety OfficersLaboratory Safety Officers (LSOs) are department or area-specific resources who are qualified by training or experience to provide technicallaboratory safety guidance in the school or unit assigned. LSOs are useful in helping to create and enhance a safe laboratory workingenvironment.

Assignment of an LSO

Department chairs are responsible for assigning one or more LSOs for their department. Any department with active laboratories (instructional,research, and other types as identified) are required to have at least one LSO.

Duties of an LSO

The primary duty of an LSO is to act as a liaison on safety-related issues with RMS personnel as needed. Additionally, LSO's are to be familiarwith and understand the Laboratory Safety Rules and Best Practices found in of this plan.Appendix I

Other duties of an LSO may include:

Laboratory Inspections

Assisting in laboratory inspection process and complete inspection reports as neededHelp resolve identified issues found in laboratories under area of responsibility

General Safety

Respond to chemical or biochemical concerns as requested by RMSKnowledge resource for safety-related inquiries and RMS requests to disseminate informationAssist in providing chemical inventory information to RMS from responsible parties within their area

Basic Rules for Non-Laboratory Personnel In LaboratoriesAccess to laboratories is restricted to instructors, authorized personnel, and students of the laboratory course that have been trained in properlaboratory techniques when performing work with hazardous chemicals, biologicals, radio nuclides and lasers. Students and instructors arerequired to enforce the restricted access rules.

Authorized visitors are to be accompanied by laboratory personnel. Authorized visitors in the laboratory shall be instructed in basic safetyprocedures and shall be provided with appropriate protective equipment such as safety glasses and gloves.

Laboratories utilizing highly toxic chemicals, carcinogens, infectious agents, or radiation hazards shall have emergency procedures posted

1.

2.

3.

4.

5.

6.

conspicuously in the laboratory. Restricted access signs along with basic safety rules shall be posted in a conspicuous space near the entrance ofthese laboratories.

General Laboratory RulesSafe work habits and general guidelines that apply to various types of laboratories are included in this section. Instructors are encouraged todevelop laboratory-specific rules from the general guidelines or the references that have been incorporated into this safety manual.

As few laboratory chemicals are without hazards, general precautions for handling all laboratory chemicals require minimizing exposure. Skincontact with chemicals should be avoided. Avoid underestimation of the risk even when working with substances of no known significant hazard.One should assume that any mixture of hazardous chemicals is more toxic than the most toxic component. Adequate ventilation provided by fumehoods is the best means of preventing exposure to airborne substances.

Prior to working with new chemicals, the Safety Data Sheet (SDS) must be read and the precautions for safe handling observed. The SDSprovides laboratory personnel with the OSHA permissible Exposure Limits (PEL) and the ACGIH Threshold Limit Values (TLV). The PEL and TLVexposure limits shall not be exceeded.

Exposures to chemical substances above the PEL or TLV and regulated by a standard which requires monitoring, either initially or periodically,shall be monitored according to that standard. The standards require records of exposure, personal monitoring, and amounts of usage for highlytoxic or carcinogenic chemicals. OSHA standards require maintaining for a period of time, generally 2, 20, or 30 years, records of personnel whowere exposed to specific toxic chemicals.

A recommended procedure for laboratories to follow is to maintain an access log for these toxic chemicals in a bound book. The laboratory logshould have entries for the following: date, type of work performed, chemicals utilized, monitoring equipment, procedures, results, and personnelin the laboratory. The laboratory log will become a part of the permanent record of the laboratory. The above procedures are only necessary ifpersonnel are directly exposed at or above the PEL or TLV for the chemical substance regulated by a standard (see Appendix A - Definition of a

).Carcinogen and List of Known Human Carcinogens

The general rules are directed primarily toward prevention of toxic exposure and do not include rules and procedures for prevention of physicalinjury. Safety in Academic Chemistry Laboratories, a reference included in the manual, contains recommended techniques for safety operation ofequipment such as: electrical equipment, glassware, distillations, low and high temperature operations, vacuum and high pressure operations,emergency procedures, etc.

Any laboratory that desires to run experiments and/or equipment overnight unattended should fill out an "overnight experiment notice" form.These experiments include hazardous procedures, highly reactive chemicals, highly exothermic reactions, reactions that generate hazardouswaste and equipment that generates high heat or pressure. The form (see ) should be posted onAppendix B - Overnight Experiment Notice Formthe door and the other copy should be submitted to Risk Management. Principal investigators (PI) must train all the laboratory personnel on theemergency call list how to shutdown the operation.

University laboratories will be inspected quarterly when in use. A formal inspection report for each laboratory will be submitted electronically to thePI, Lab Safety Officer, and Risk Management Services department within 30 days of any inspection. Significant findings that pose an immediatethreat to life or property require re-inspection and shall be addressed, corrected or resolved by the responsible PI to sufficiently prevent, mitigateor limit the probability and/or severity of an occurrence. Laboratories with significant findings shall be re-inspected within 30 days of the notice tothe PI. Uncorrected significant findings following re-inspection will be reported to the Provost according to the judgment of the Director of RiskManagement Services.

All of the university laboratories will be inspected quarterly. A formal inspection report for each laboratory will be submitted to the PI, Lab SafetyOfficer, and Risk Management within 30 days of any inspection. Any violations should be promptly addressed and corrected by the PI. Anunannounced re-inspection shall be performed after 30 days of inspection. Any uncorrected deficiencies will be reported to the Provost Office forenforcement.

The following procedures are used when working with chemicals:

Accidents and Spills

Eye contactPromptly flush eyes with water for 15 minutes, and seek medical attention.IngestionConsult the product SDS health and first aid section. Generally, the victim should be encouraged to drink large amounts of water.Skin contactPromptly flush the affected area with copious amounts of water and remove any contaminated clothing; use a emergency shower whencontact is extensive. If symptoms persist after washing, seek medical attention.Seek immediate medical attentionEncourage the injured person to go to the Student Health Center immediately.Clean-upPromptly clean up spills, using appropriate protective clothing and equipment, along with proper disposal methods.ReportAccidents should be reported to the immediate supervisor who will fill out the proper forms. The supervisor should report the accident toRisk Management Services, (940) 565-2109, immediately for prompt reporting and investigation.

1. 2. 3. 4. 5.

Spill Cleanup

Chemical spills are contained using the :Think C.L.E.A.N Plan

Contain the spillLeave the areaEmergency: eye wash, shower, medical careAccess SDSNotify a supervisor

All spills are to be contained using appropriate absorbent or spill kits. When spills involving large quantities of hazardous material occur, contactthe laboratory supervisor or Chemical Hygiene Officer who will direct clean-up or evacuation procedures. Spill kits will be provided upon request.

Rules for Safe Laboratory Work

Safe work habits

Procedures to avoid unnecessary exposure to chemicals:

Laboratory management (PIs, professors and lab managers) are responsible for conducting weekly testing of eyewash fountains, and forthe proper operation of all laboratory safety equipment, including fire extinguishers and emergency showers.Laboratory personnel shall be aware of the location and proper operating of laboratory safety equipment including fire extinguishers;emergency showers; and eyewash fountains.Visitors to the laboratory shall abide by all laboratory safety rules, including requirements for the use of eye protection.Eye protection should be worn at all times in the laboratory. Spectacles, safety glasses and other eye protection devices shall be keptclean at all times.Seek information (from SDS) and advice about hazards, plan appropriate protective procedures, and plan positioning of equipmentbefore beginning any new operation.Use minimum amounts of chemicals to accomplish task.Substitute less hazardous materials whenever possible.Do not smell or taste chemicals. Avoid inhalation from apparatus that can discharge toxic chemicals such as vacuum pumps, distillationcolumns, reflux columns, etc., by venting the equipment into a local exhaust.Do not allow release of toxic substances in rooms which have contained re-circulating atmospheres.Use only those chemicals for which the quality of the available ventilation system is appropriate.Handle and store laboratory glassware with care to avoid damage; do not use damaged glassware. Use extra care with Dewar flasks andother evacuated glass apparatus; shield or wrap them to contain chemicals and fragments should implosion occur. Use equipment onlyfor its designed purpose.Wash areas of exposed skin thoroughly before leaving the laboratory.Avoid behavior that might confuse, startle or distract another worker.Do not use mouth suction for pipetting or starting a siphon.Avoid working alone in a laboratory while hazardous procedures are being conducted.Warning signs with personnel contact information shall be posted on the door and on equipment where special or unusual hazards exist.Provide for the containment of toxic substances in the event of failure of utility service when operating unattended equipment. Also,ensure that the warning signs are in place.Work areas shall be maintained clean and uncluttered with chemicals and equipment properly labeled and stored; clean up the work areaon completion of an operation and at the end of each day.Hood operations: Use a hood for operations that might result in release of toxic chemical vapors or dust. Use a fume hood or other localventilation device when working with any volatile substance with a TLV of less than 50 ppm. (Confirm adequate hood performance beforeuse. Keep hood closed when operations are not being performed in the hood. Do not allow materials to block vents or air-flow. Do notstore materials in the hood.)Be aware of unsafe conditions and see that they are corrected when detected.All the laboratories should be inspected by the Lab Safety Officers once per semester unless they are inactive.

Personal Protective Equipment (PPE)

A face shield of chemical goggles shall be worn when conducting operations utilizing glassware, distilling or refluxing; and transferring ormixing corrosives of toxic liquids.Confine long hair and loose clothing especially if working with moving machinery.The preferred footwear are shoes which completely encloses the foot.Wear appropriate impervious gloves when the potential for contact with toxic materials exists; inspect the gloves before each use, washgloves prior to removal, and replace gloves that have deteriorated.Stop using the chemical when air contaminant concentrations are not sufficiently reduced by engineering controls. Inspect respiratorsprior to each use. Medical evaluations are required before the use of respiratory equipment.Use any protective and emergency apparel and equipment as appropriate.If contact lenses are worn in the laboratory, inform the supervisor so special precautions can be taken. We strongly recommend againstthe use of contact lenses in the lab. The potential for chemical buildup under them is too great.

Remove laboratory coats or other clothing immediately upon significant contamination.Leave lab coats in the lab.Proper handling and disposal methods of hazardous waste and materials; contact Risk Management Services for a hazardous waste

.pickup

Laboratory Hygiene Requirements

Allergens and Embryo Toxins

Procedures and precautions

Allergens such as diazomethane, isocyanates, and bichromates, require wearing suitable gloves to prevent hand contact with allergensor substances of unknown allergenic activity. Laboratory hoods or glove boxes are a preferred enclosure for allergen work.Embryo toxins such as organomercurials, lead compounds, and formamide require women of childbearing age to only work with thesesubstances in a hood whose satisfactory performance has been confirmed. Appropriate protective clothing is required to prevent skincontact.Procedures for safe handling, use, and storage of allergens and embryo toxins shall be reviewed annually and prior to the introduction ofany new material.Allergens and embryo toxins shall be properly labeled and stored in unbreakable secondary containers in adequately ventilated areas.Spills and incidents of exposure to these materials require immediate notification of supervisor and consultation of a qualified physicianwhen appropriate.Chemicals of moderate chronic or high acute toxicity ( ) may not exceed TLV50 ppm, e.g. hydrogenAppendix E - Acutely Toxic Chemicalscyanide and hydrofluoric acid (NFPA 3 or 4).

Moderate chronic and high acute toxicity

Additional precautions are appropriate when working with chemicals of moderate chronic and high acute toxicity (see Appendix E - Acutely Toxic).Chemicals

Minimize exposure to these toxic substances by any route using all reasonable precautions and appropriate protective equipment,including washing of hands and arms thoroughly after removal of protective equipment.Use and store these substances only in areas of restricted access. The storage area containers require special warning signs to alertusers of the hazards and safe handling procedures.Use in hoods that have been previously evaluated to confirm adequate performance. Trap released vapors to prevent their discharge intothe hood exhaust.Maintain records of the amounts of these materials on hand, amounts used, and names of personnel working with the materials.Accidents and spills are prevented by preparing the work area prior to chemical handling.Assure that at least two people are present at all times when working with highly toxic materials.Cover the work area with containment devices such as plastic sheeting and absorbent materials. Prepare a waste disposal receptacle forthe waste chemicals and containment material.If a major spill occurs outside of the hood, evacuate the area. Assure that cleanup personnel wear suitable protective equipment.

Chemicals with High Chronic Toxicity

Organic mercury compounds and carcinogens; see (NFPA 3 or 4).Appendix E - Acutely Toxic Chemicals

Procedures and Supplemental Rules

Restrict all transfers and work with these substances to a "controlled area" such as a restricted access hood, glove box, or a portion ofthe laboratory designated for use of highly toxic substances. Personnel in the laboratory must be made aware of the substances beingused and necessary precautions.

Eating, drinking, smoking, gum chewing, or applying cosmetics is prohibited in the laboratories. Wash hands before conducting theseactivities.

Storing, handling, or consuming food or beverages in laboratories and storage areas is prohibited.

Carcinogens are those listed in the definition of a carcinogen in Appendix A - Definition of a Carcinogen and List of Known Human.Carcinogens

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

Prior to introduction of highly toxic materials in the laboratory, prepare a plan for the use, disposal and decontamination of equipment.The controlled area must be decontaminated after using highly toxic materials.Personnel shall remove protective equipment and place it in an appropriate labeled container. Personnel will thoroughly wash hands,forearms, face, and neck after removing protective equipment.Laboratory personnel are responsible for cleaning the area when highly toxic materials are used. The area must be decontaminated priorto allowing Janitorial personnel to resume normal cleaning procedures.Medical surveillance is required if using significant quantities of a highly toxic material on a regular basis (three times per week). Consulta qualified physician concerning desirability of regular medical monitoring. Only if the SOP (Standard Operating Procedure) for the use ofthe chemical insures no exposure to personnel at or above the PEL and/or TLV can the material be used without medical monitoring.Maintain records of the amounts of these materials on hand, amounts used, and names of personnel working with the materials.Accidents and spills are prevented by preparing the work area prior to chemical handling.Assure that at least two people are present at all times when working with highly toxic materials.Cover the work area with containment devices such as plastic sheeting and absorbent. Prepare a waste disposal receptacle for the wastechemicals and containment material.If a major spill occurs outside of the hood, evacuate the area. Assure that cleanup personnel wear suitable protective equipment.

Explosive Chemical Management

An explosive chemical is a gas, solid or liquid chemical which is in itself capable by chemical reaction of producing gas at a temperature andpressure at a speed able to cause damage to the surroundings. This includes chemicals purchased from supplied by vendors or products andby-products generated from experiments or reactions. Examples of explosive chemicals are:

organic peroxidesoxidizers includes salts containing nitrateschlorateshigh concentration of perchloric acids

The following procedures must be followed to minimize the risk of explosion.

ResponsibilityThe PI involved in using explosive chemicals must perform a Risk Assessment prior to submitting a research proposal to the RiskManagement Services for approval. Detailed Standard Operating Procedures must be attached with the proposal.PurchasingAll chemicals must be purchased through EIS approval system.Chemical RegisterA register of all used/stored chemicals on site shall be generated by the manager of the lab or PI. This list should submitted to RiskManagement Services for review.Chemical UserA list of chemical users includes name, employment status, contact email address, phone number and training status must be submittedwith Standard Operating procedures (SOP) to Risk Management Services .New chemical hazard identification and risk assessmentFor all new chemicals, a hazard and risk assessment must be performed immediately.TrainingStaff and workers must receive related training before handling the chemicals and doing any hands-on experiments.LabelingThe label must be specific and firmly secured on the container.Personal Protective EquipmentAppropriate Personal Protective Equipment must be worn during experiment.Handling and storage of chemicalsProper procedures found in the SDS sheets must be used.Waste disposalChemical waste must not be mixed with other chemical waste unless the waste is the same type. Users must take “Hazardous Wastes”training prior to handling explosive waste,Updates and recordsAll SDS’s must be updated regularly. Risk Managements Services ensures that new chemicals are entered into the Database inventory.SignageWarning signage must be posted on the wall or entrance to warn building occupants of any hazards.Emergency phone numberEmergency contact numbers of responsible lab persons, the PI(s), and the UNT Police department must be posted on the outside labdoor.Overnight experimentsDescribe how to stop the process(es) or turn off the equipment if an emergency happens; also attach a map showing all equipmentlocations in the lab. See for details.Appendix B - Overnight Experiment Notice FormIncident reportPrincipal Investigator or Lab Manager must report any incident to the Risk Management Services within 7 working days. Injuries involvingemployees require separate report to Risk Management Services Insurance and Claims, (940) 565-2109.

Lasers

Procedures

The type and intensity of radiation from lasers varies widely with the instrument design. Prior to working with an instrument, thespecifications for operation and protection must be consulted.Always wear goggles that offer protection against the specific wavelength of laser in use. If more than one wavelength is being used,additional goggles specific for each wavelength are required. No available spectacles protect against all laser wavelengths.Never look directly at the beam or pump source.Never view the beam pattern directly; use an image converter or other safe, indirect means. To decrease reflecting hazards, do not aimby looking along the beam.Do not allow any objects that cause reflections to be present in or along the beam. Even buttons on clothing and polished screw headscan be dangerous.Keep a high general illumination level in areas where lasers are in operation. Low light levels cause dilation of the pupils, therebyincreasing the hazard.Display warning signs in laser areas.

Laboratory Use of Carcinogens

When carcinogens are used in a laboratory, access to the laboratory will be clearly restricted to personnel trained in safe handling of highly toxicmaterial. See for the criteria for a chemical being listed as a carcinogen and for listed carcinogens and suspected carcinogens.Appendix AAnything categorized by IARC as Groups I and II is covered by the Hazard Communication Standard and the Laboratory Standard.

Group I known human carcinogens

Groups IIA and IIB probable human carcinogens

Group III substances evaluated, but no human carcinogenicity classification could be made

Access and use of highly toxic substances and carcinogens shall be controlled and monitored. Instructors and graduate students using thesematerials shall record the amounts used, date and persons working with the materials. A separate inventory list of carcinogens, suspectedcarcinogens, reproductive toxins and highly toxic substances is recommended.

Back to Top

Control Measures Implementation

Chemical StorageChemicals are stored according to segregation systems that separate incompatible classes of chemicals. Flammables, acids, bases, oxidizers,water reactives, and peroxides require special attention for proper storage. A list of incompatible chemicals which require special precautions forsafe storage is provided in . Appendix C lists the maximum allowable container capacity forAppendix C - List of Incompatible Chemicalscontainers such as: glass bottles, metal cans, plastic bottles or pails, safety cans and metal drums. Certain chemical manufacturers and suppliersprovide additional storage and segregation information on the product label or SDS.

Storage of laboratory chemicals presents an ongoing safety problem. Amounts of chemicals in storage should be as small as practical. Storageon bench tops and in fume hoods is prohibited due to the potential for fire and spills. Certain reactive or unstable chemicals are stores in speciallydesigned refrigerators. Flammable liquids are stored in an approved flammable storage cabinet.

Safety cans with a spring loaded spout are preferred for transporting flammable liquids. Alternatively, when chemicals are hand carried, thecontainer may be placed in an outside container or a plastic pail.

Stored chemicals shall be periodically inspected for deterioration and container integrity. Chemicals which are no longer used in the laboratoryshall be discarded by labeling it with a chemical waste tag. Contact Risk Management Services to .request a hazardous waste pickup

Cylinders of compressed gases are to be strapped or chained to a wall or bench top and are capped when not in use.

Engineering ControlsAir flow through the laboratory should be relatively uniform and be exhausted to the exterior of the building.

All laboratory fume hoods are inspected annually and certified by the Chemical Hygienist. Any hood not passing inspection should be taken out of

No person may use a laser of any type prior to training in laser safety. Contact the Radiation Safety Officer at 940-565-3282 toobtain this training.

service immediately and not used until it has been repaired. Repair should be in a timely manner so as not to endanger the health and well-beingof students and employees or place the facility at risk.

Ventilated storage cabinets for chemicals are provided as needed. The Chemical Hygienist shall maintain inspection and repair records forlaboratory safety equipment. Annual inspections and/or testing are required for the following: eyewash fountains; emergency showers; and fireextinguishers.

Personal Protective EquipmentSafety glasses are recommended for all laboratory work. Chemical goggles shall be worn when performing potentially hazardous operations.

Face shields and chemical goggles are worn to prevent injury from splashes or sprays of hazardous chemicals or biohazards if there is a potentialfor eye, nose, or mouth contamination. This equipment is located in the laboratories when there is a need for the equipment.

Laboratory personnel are required to wear appropriate impervious gloves when there is a potential for direct skin contact with hazardouschemicals or blood bome pathogens.

When the probability of chemical splashes is great, an impervious apron appropriate for the task is worn.

All personal protective equipment shall be removed immediately upon leaving the work area; cleaned, and placed in an appropriate area.

Exposure Levels and Medical MonitoringExposure to chemical substances regulated by a standard which requires monitoring, either initially or periodically, shall be monitored accordingto the standard. If the initial monitoring discloses exposure over the PEL, then immediate compliance with the exposure and medical monitoringprovisions of the relevant standard is required. Compliance with the standard may include more frequent monitoring and implementation ofadditional control measures.

Personnel shall be notified in writing of monitoring data within 15 days of receipt of those monitoring results.Exposure records will be maintained for personnel exposed above the TLV and/or PEL of the following chemicals: chemicals covered by astandard; carcinogens; and highly toxic materials. Exposure, medical, and personnel monitoring records will be maintained for thirty years.

Monitoring is required in laboratories where chemicals specifically regulated by OSHA CFR 1910 subpart Z are used. See Appendix A - Definition for the OSHA Carcinogens.of a Carcinogen and List of Known Human Carcinogens

If any of the above described chemicals are to be used in the laboratory, a work procedure which identifies each workstation/task in the laboratoryand the required controls and equipments will need to be included in the Laboratory Safety Manual.

Back to Top

NanoparticlesNanotechnology is the use and control of particulates of roughly 1 to 100 nanometers. Nanoparticles can cross an alveolar wall into bloodstream.It also can spread to other organs, tissues and brain. Potential nanomaterial exposure routes include inhalation, dermal contact, and ingestion. Toprevent the exposure, always maintain good work practices like clean work areas, hand washing, and shower use /change of clothes).

Use engineering controls like source enclosure, local exhaust ventilation, and HEPA filters. During any experiment, wear NIOSH-approvedpersonal protective equipment and respirator. Cleanup any spill immediately and properly dispose of any Nanomaterials. Report any accidents ornear-miss accidents to your supervisor.

Back to Top

TrainingEffective training is crucial to a successful laboratory safety program. Laboratory Supervisors must actively participate in the training process toensure that all lab employees are effectively trained before any work with hazardous materials occurs. It should be noted that depending on thetype of research being conducted and associated hazards, there may be additional training requirements. For more information, contact RMS at(940)565-2109 or visit the RMS Training webpage.

( ) http://riskmanagement.unt.edu/training/environmental-services-training

1. 2.

1. 2. 3. 4. 5. 6.

Back to Top

Contaminated Waste Removal/Disposal

General Methods for Segregation and DisposalTo assure that minimal harm to people and the environment will result from the disposal of waste laboratory chemicals, segregation and disposalshall be in accordance with to provisions of the following:

Code of Federal Regulations, , Department of TransportationTitle 49, Parts 172-173Code of Federal Regulations, , Environmental Protection AgencyTitle 40, Parts 261-262

Certain non-hazardous chemicals are permissible for sanitary sewer disposal. In general, only those solutions from routine titrations and testswhich do not contain any hazardous chemical will be allowed to be put into the sanitary sewer system.

The following types of hazardous materials must be segregated for disposal:

Non-flammable organic liquids or solids.Solutions of heavy metals.Hydrocarbons, halogenated hydrocarbons, nitro compounds, mercaptans, and most oxygenated compounds.Organics that are explosive such as azides and peroxides.Concentrated acids or bases (6 molar or higher).Highly toxic, malodorous, or lachrymatory substances (such as cyanides or carcinogens; see Appendix A - Definition of a Carcinogen and

).List of Known Human Carcinogens

Indiscriminate disposal by pouring waste down the drain or adding them to mixed refuse for landfill burial in unacceptable. Hoods are not to beused as a means of disposal for volatile chemicals.

Hazardous WasteReference the for information on hazardous waste management. Waste in need of disposal is required toHazardous Waste Management Guidebe tagged with a hazardous waste tag, with the contents listed on this tag. Complete a to have theHazardous Materials Pickup Request formmaterial picked up.

Radioactive WasteSee the located on the RMS website.Radiation Waste Handling SOP

RMS Standard Operating Procedures (SOP)

All SOPs related to the chemical hygiene plan can be found at the RMS website ( ).www.rms.unt.edu

These include:

Arts and Crafts Safety SOPChemical Materials Purchase Review SOPControlled Substance SOPEye Wash Station Inspection SOPLaboratory Safety SOPLaser Safety SOPMinors in Labs SOPNano-Particle SOPRefrigerant SOP

RevisionLast approved revision: 2/2016

Appendix A - Definition of a Carcinogen and List of KnownHuman CarcinogensSelect CarcinogensA carcinogen is a substance or chemical that after chronic exposure will cause some part or parts of the body to begin cancerous growth leadingto harmful effects on the affected organ(s).

All of these materials require special handling, and are usually used only under a hood with full PPE protection (gloves, goggles, apron, et al.).Most have very low TLV and/or PEL values indicating the harmfulness of the compound. Since these are known human carcinogens, all requirespecific standard operating procedures (SOPs) to be written when used in any UNT laboratory.

Many times, it is much easier to find a replacement chemical than to set up the engineered environmental controls and operating proceduresrequired to maintain safe use of these chemicals. If electing to use any of these chemicals, a Principal Investigator or laboratory manager mustpublish an SOP and ensure that engineering controls always keep the chemical below the PEL and/or TLV when laboratory personnel areexposed to a listed material.

The following list of known human carcinogens fall under the Substance Specific Standards for each chemical:

Aflatoxins Alcoholic BevarageConsumption

4-aminodiphenyl

Analgesic Mixtures Containing Phenacetin Aristolochic Acids Arsenic and Inorganic Arsenic Compounds

Asbestos Azathioprine benzene

benzidine Beryllium and BerylliumCompounds

Bis(chloromethyl)Ether and Technical-GradeChloromethyl Methyl Ether

1,3-Butadiene Cadmium and CadmiumCompunds

Chlorambucil

1-(2-Chloroethyl)-3-(4-methylcyclohexyl)-1-nitrosourea Chromium HexavalentCompounds

Coal Tars and Coal-Tar Pitches

Coke-Oven Emissions Cyclophosphamide Cyclosporin A

Diethylstibestrol Dyes Metabolized toBenzidine

Erionite

Estrogens, Steroidal Ethylene Oxide Formaldehyde

Hepatitis B Virus Hepatitis C Virus Human Papillomaviruses: Some Genital-MucosalTypes

Melphalan Methoxalen with UltravioletA Therapy

Mineral Oils: Untreated and Mildly Treated

Mustard Gas 2-Naphthylamine Neutrons

Nickel Compounds Radon Silica, Crystalline(Respirable Size)

Solar Radiation Soots Strong Inorganic Acid Mists Containing Sulfuric Acid

Sunlamps or Sunbeds, Exposure to Tamoxifen 2,3,7,8-Tetrachlorodibenzo-p-dioxin

Thiotepa Thorium Dioxide Tobacco Smoke, Environmental

Tobacco Smoke Tobacco, Smokeless Ultraviolet Radiation, Broad-Spectrum

Vinyl Chloride Wood Dust X-Radiation and Gamma Radiation

Reasonably Anticipated to be Human CarcinogensAll of the following chemicals are expected to follow the same precautions as those described in the section above.Select Carcinogens

Acetaldehyde 2-Acetylaminofluorene Acrylamide

Adriamycin 2-Aminoanthraquinone o-Aminoazotoluene

1-Amino-2,4-dibromoanthraquinone 2-Amino-3,4-dimethylimidazo[4,5-f]quinoline 2-Amino-3,8-dimethylimidazo[4,5-f]quinoxaline

1-Amino-2-methylanthraquinone 2-Amino-3-methylimidazo[4,5-f]quinoline 2-Amino-1-methyl-6-phenylimidazo[4,5-b]pyridine

Amitrole o-Anisidine and its Hydrochloride Azacitidine

Basic Red 9 Monohydrochloride Benz[a]anthracene Benzo[b]fluoranthene

Benzo[j]fluoranthene Benzo[k]fluoranthene Benzo[a]pyrene

Benzotrichloride 2,2-Bis(bromomethyl)-1,3-propanediol Bis(chloroethyl) Nitrosourea

Bromodichloromethane 1,4-Butanediol Dimethanesulfonate Butylated Hydroxyanisole

Captafol Carbon Tetrachloride Ceramic Fibers(Respirable Size)

Chloramphenicol Chlorendic Acid Chlorinated Paraffins(C , 60% Chlorine)12

Chloroform 1-(2-Chloroethyl)-3-cyclohexyl-1-nitrosourea 3-Chloro-2-methylpropene

4-Chloro-o-phenylenediamine Chloroprene p-Chloro-o-toluidine and its Hydrochloride

Chlorozotocin Cisplatin Cobalt Sulfate

Cobalt-Tungsten Carbide: Powders andHard Metals

p-Cresidine Cupferron

Dacarbazine Danthron 2,4-Diaminoanisole Sulfate

2,4-Diaminotoluene Diazoaminobenzene Dibenz[a,h]acridine

Dibenz[a,f]acridine Dibenz[a,h]anthracene 7H-Dibenzo[c,g]carbazole

Dibenzo[a,e]pyrene Dibenzo[a,h]pyrene Dibenzo[a,i]pyrene

Dibenzo[a,f]pyrene 1,2-Dibromo-3-chloropropane 1,2-Dibromoethane

2,3-Dibromo-1-propanol 1,4-Dichlorobenzene 3,3’-Dichlorobenzidine and its Dihydrochloride

Dichlorodiphenyltrichloroethane 1,2-Dichloroethane Dichloromethane

1,3-Dichloropropene Diepoxybutane Diesel Exhaust Particulates

Di(2-ethylhexyl) Phthalate Diethyl Sulfate Diglycidyl Resorcinol Ether

3,3’-Dimethoxybenzidine 4-Dimethylaminoazobenzene 3,3’-Dimethylbenzidine

Dimethylcarbamoyl Chloride 1,1-Dimethylhydrazine Dimethyl Sulfate

Dimethylvinyl Chloride 1,6-Dinitropyrene 1,8-Dinitropyrene

1,4-Dioxane Disperse Blue 1 Dyes Metabolized to 3,3’-Dimethoxybenzidine

Dyes Metabolized to3,3’-Dimethylbenzidine

Epichlorohydrin Ethylene Thiourea

Ethyl Methanesulfonate Furan Glass Wool Fibers(Inhalable)

Glycidol Hexachlorobenzene Hexachloroethane

Hexamethylphosphoramide Hydrazine and Hydrazine Sulfate Hydrazobenzene

Indeno[1,2,3-cd]pyrene Iron Dextran Complex Isoprene

Kepone Lead and Lead Compounds Lindane, Hexachlorocyclohexane, and otherHexachlorocyclohexane Isomers

2-Methylaziridine 5-Methylchrysene 4,4’-Methylenebis

4,4’-Methylenebis benzenamine 4,4’-Methylenedianiline and itsDihydrochloride

Methyleugenol

Methyl Methanesulfonate N-Methyl-N’-Nitro-N-Nitrosoguanidine Metronidazole

Michler’s Ketone Mirex Naphthalene

Nickel, Metallic Nitrilotriacetic Acid o-Nitroanisole

Nitrobenzene 6-Nitrochrysene Nitrofen

Nitrogen Mustard Hydrochloride Nitromethane 2-Nitropropane

1-Nitropyrene 4-Nitropyrene N-Nitrosodi-n-butylamine

N-Nitrosodiethanolamine N-Nitrosodiethylamine N-Nitrosodimethylamine

N-Nitrosodi-n-propylamine N-Nitroso-N-ethylurea 4-(N-Nitrosomethylamino)-1-(3-pyridyl)-1-butanone

N-Nitroso-N-methylurea N-Nitrosomethylvinylamine N-Nitrosomorpholine

N-Nitrosonornicotine N-Nitrosopiperidine N-Nitrosopyrrolidine

N-Nitrososarcosine o-Nitrotoluene Norethisterone

Ochratoxin A 4,4’-Oxydianiline Oxymetholone

Phenacetin Phenazopyridine Hydrochloride Phenolphthalein

Phenoxybenzamine Hydrochloride Phenytoin and Phenytoin Sodium Polybrominated Biphenyls

Polychlorinated Biphenyls Procarbazine and Its hydrochloride Progesterone

1,3-Propane Sultone -Propiolactone Propylene Oxide

Propylthiouracil Reserpine Riddelliine

Safrole Selenium Sulfide Streptozotocin

Styrene Styrene-7,8-oxide Sulfallate

Tetrachloroethylene Tetrafluoroethylene Tetranitromethane

Thioacetamide 4,4’-Thiodianiline Thiourea

Toluene Diisocyanates 0-Toluidine and its Hydrochloride Toxaphene

Trichloroethylene 2,4,6-Trichlorophenol 1,2,3-Trichloropropane

Tris(2,3-dibromopropyl)Phosphate Ultraviolet Radiation A Ultraviolet Radiation B

Ultraviolet Radiation B Ultraviolet Radiation C Urethane

Vinyl Bromide 4-Vinyl-1-cyclohexene Diepoxide Vinyl Fluoride

Appendix B - Overnight Experiment Notice FormProceduresThe overnight experiment notice form is to be used by persons with laboratory experiments that take place overnight. Fill out the form, provide acopy to the Risk Management Services department (565-2109), and post on door(s) where experiment will be performed.

Download FormDownload .RMS Overnight Experiment Notice Form

Appendix C - List of Incompatible ChemicalsThe most complete and reliable reference on chemical reactivity is found in the current edition of "Handbook of Reactive Chemical Hazards" by L.Bretherick, published by Butterworths. Reactivity information is sometimes given in manufacturer's MSDSs and on labels. Also, guidelines onwhich chemicals are reactive can be found in regulations promulgated by the Department of Transportation (DOT) in 49 CFR and by theEnvironmental Protection Agency (EPA) in 40 CFR. Also see NFPA Manual 325 M--"Fire Hazard Properties of Flammable Liquids, Gases,Volatile Solids", Manual 49 "Hazardous Chemicals Data", and Manual 491M "Manual of Hazardous Chemical Reactions".

Examples of Incompatible ChemicalsFrom: "Safety in Academic Chemistry Laboratories", American Chemical Society

CHEMICAL ... is incompatible with ...

Acetic acid Chromic acid, nitric acid, hydroxyl compds, ethylene glycol, perchloric acid, peroxides, permanganates

Acetylene Chlorine, bromine, copper, fluorine, silver, mercury

Acetone Nitric acid and sulfuric acid mixtures

Ammonia (anhydrous) Mercury,chlorine, calcium hypochloride, iodine, bromine, hydrofluoric acid

Ammonium nitrate Acids, powdered metals, flammable liquids, chlorates, nitrites, sulfur, finely divided organic combustible materials

Aniline Nitric acid, hydrogen peroxide

Arsenical materials Any reducing agent

Azides Acids

Bromine See chlorine

Calcium oxide Water

Carbon (activated) Calcium hypochlorite, all oxidizing agents

Carbon tetrachloride Sodium

Chlorates Ammonium salts, acids, powdered metals, sulfur, finely divided organic combustible materials

Chromic acid and chromium Acetic acid, naphthalene, camphor, glycerol, alcohol, flammable liquids

Chlorine Ammonia, acetylene, butadiene, butane, methane, propane(or other petroleum gases), hydrogen, sodium carbide,benzene, finely divided metals, turpentine

Chlorine dioxide Ammonia, methane, phosphine, hydrogen sulfide

Copper Acetylene, hydrogen peroxide

Cumene hydroperoxide Acids (organic or inorganic)

Cyanides Acids

Flammable liquids Ammonium nitrate, chromic acid, hydrogen peroxide, nitric acid, sodium peroxide, halogens

Fluorine All other chemicals

Hydrocarbons (such as butane,propane, benzene)

Fluorine, chlorine, bromine, chromic acid, sodium peroxide

Hydrocyanic acid Nitric acid, alkali

Hydrofluoric acid (anhydrous) Ammonia (aqueous or anhydrous)

Hydrogen peroxide Copper, chromium iron, most metals or their salts, alcohols, acetone, organic materials, aniline, nitromethane,combustible materials

Hydrogen sulfide Fuming nitric acid, oxidizing gases

Hypochlorites Acids, activated carbon

Iodine Acetylene, ammonia (aqueous or anhydrous), hydrogen

Mercury Acetylene, fulminic acid, ammonia

Nitrates Sulfuric acid

Nitric acid (concentrated) Acetic acid, sulfuric acid, aniline, chromic acid, hydrocyanic acid, hydrogen sulfide, flammable liquids, flammablegases, copper, brass, any heavy metals

Nitrites Acids

Nitroparaffins Inorganic bases, amines

Oxalic acid Silver, mercury

Oxygen Oils, grease, hydrogen, flammable liquids, solids or gases

Perchloric acid Acetic anhydride, bismuth and its alloys, alcohol, paper, wood, grease, oils

Peroxides, organic Acids (organic or mineral), avoid friction, store cold

Phosphorus (white) Air, oxygen, alkalis, reducing agents

Potassium Carbon tetrachloride, carbon dioxide, water

Potassium chlorate Sulfuric and other acids

Potassium perchlorate Sulfuric and other acids

Potassium permanganate Glycerol, ethylene glycol, benzaldehyde, sulfuric acid

Selenides Reducing agents

Silver Acetylene, oxalic acid, tartartic acid, ammonium compounds, fulminic acid

Sodium Carbon tetrachloride, carbon dioxide, water

Sodium nitrite Ammonium nitrate and other ammonium salts

Sodium peroxide Ethyl or methyl alcohol, glacial acetic acid, acetic anhydride, benzaldehyde, carbon disulfide, glycerin, ethylene glycol,ethyl acetate, methyl acetate, furfural

Sulfides Acids

Sulfuric acid Potassium chlorate, potassium perchlorate, potassium permanganate (similar compounds of light metals, such assodium, lithium)

Tellurides Reducing agents

Appendix D - Maximum Allowable Container Capacities StoredOutside a Flammable Cabinet

Glass bottles: maximum of one quart (1 liter) of any flammable liquid stored outside a flammable cabinet. Use safety cans for largervolumes than this.Metal cans: maximum of one gallon (4 liter can) of any flammable liquid stored outside a flammable cabinet. Use safety cans for largervolumes than this. A 5 gallon (20 liters) can may be used if a flame arrestor is present in the dispenser nozzle.Plastic bottles: maximum of one quart (1 liter) of any flammable liquid stored outside a flammable cabinet. Use safety cans for largervolumes than this.Plastic pails: if flame arresters are present in the nozzle, then 5 gallon pails can be used to dispense flammable liquids.Safety cans: up to 5 gallons of a flammable liquid may be dispensed from safety cans having a self-closing lid and flame arrester.Metal drums: dispensing flammable liquids from metal drums requires grounding of the nozzle to a good ground and grounding of thereceiving vessel during transfer of the liquid.

Appendix E - Acutely Toxic ChemicalsBased on OSHA Standard 29 CFR, 1910.119, Appendix A.

CHEMICAL LOOKUP # CHEMICAL NAMES

75-07-0 Acetaldehyde

107-02-8 Acrolein (2-Propenal)

814-68-6 Acrylyl Chloride

107-05-1 Allyl Chloride

107-11-9 Allylamine

Varies Alkylaluminums

7664-41-7 Ammonia, Anhydrous

7664-41-7 Ammonia solutions (greater than 44% ammonia by weight)

7790-98-9 Ammonium Perchlorate

7787-36-2 Ammonium Permanganate

7784-42-1 Arsine (also called Arsenic Hydride)

542-88-1 Bis(Chloromethyl) Ether

10294-34-5 Boron Trichloride

7637-07-2 Boron Trifluoride

7726-95-6 Bromine

13863-41-7 Bromine Chloride

7789-30-2 Bromine Pentafluoride

7787-71-5 Bromine Trifluoride

106-96-7 3-Bromopropyne (also called Propargyl Bromide)

75-91-2 Butyl Hydroperoxide (Tertiary)

614-45-9 Butyl Perbenzoate (Tertiary)

75-44-5 Carbonyl Chloride (see Phosgene)

353-50-4 Carbonyl Fluoride

9004-70-0 Cellulose Nitrate (Concentration greater than 12.6% nitrogen)

7782-50-5 Chlorine

10049-04-4 Chlorine Dioxide

13637-63-3 Chlorine Pentrafluoride

7790-91-2 Chlorine Trifluoride

96-10-6 Chlorodiethylaluminum (also called Diethylaluminum Chloride)

97-00-7 1-Chloro-2,4-Dinitrobenzene

107-30-2 Chloromethyl Methyl Ether

76-06-2 Chloropicrin

None Chloropicrin and Methylbromide Mixt.

None Chloropicrin and Methylchloride Mixt.

80-15-9 Commune Hydroperoxide

460-19-5 Cyanogen

506-77-4 Cyanogen Chloride

675-14-9 Cyanuric Fluoride

110-22-5 Diacetyl Peroxide (concentration greater than 70%)

334-88-3 Diazomethane

94-36-0 Dibenzoyl Peroxide

19287-45-7 Diborane

110-05-4 Dibutyl Peroxide (Tertiary)

7572-29-4 Dichloro Acetylene

4109-96-0 Dichlorosilane

557-20-0 Diethylzinc

105-64-6 Diisopropyl Peroxydicarbonate

105-74-8 Dilauroyl Peroxide

75-78-5 Dimethyldichlorosilane

57-14-7 Dimethylhydrazine, 1,1-

124-40-3 Dimethylamine, Anhydrous

97-02-9 Dinitroaniline-2,4

1338-23-4 Ethyl Methyl Ketone Peroxide (also Methyl Ethyl Ketone Peroxide; concentration > 60%)

109-95-5 Ethyl Nitrite

75-04-7 Ethylamine

371-62-0 Ethylene Fluorohydrin

75-21-8 Ethylene oxide

151-56-4 Ethyleneimine

7782-41-4 Fluorine

50-00-0 Formaldehyde (Formalin)

110-00-9 Furan

684-16-2 Hexafluoroacetone

7647-01-0 Hydrochloric Acid, Anhydrous

7664-39-3 Hydrofluoric Acid, Anhydrous

10035-10-6 Hydrogen Bromide

7647-01-0 Hydrogen Chloride

74-90-8 Hydrogen Cyanide, Anhydrous

7664-39-3 Hydrogen Fluoride

7722-84-1 Hydrogen Peroxide (52% by wt or >)

7783-07-5 Hydrogen Selenide

7783-06-4 Hydrogen Sulfide

7803-49-8 Hydroxylamine

13463-40-6 Iron, Pentacarbonyl

75-31-0 Isopropylamine

463-51-4 Ketene

78-85-3 Methacrylaldehyde

920-46-7 Methacryloyl Chloride

30674-80-7 Methacryloyloxyethyl Isocyanate

126-98-7 Methyl Acrylonitrile

74-89-5 Methylamine, Anhydrous

74-83-9 Methyl Bromide

74-87-3 Methyl Chloride

79-22-1 Methyl Chloroformate

1338-23-4 Methyl Ethyl Ketone Peroxide (concentration > 60%)

453-18-9 Methyl Fluoroacetate

421-20-5 Methyl Fluorosulfate

60-34-4 Methyl Hydrazine

74-88-4 Methyl Iodide

624-83-9 Methyl Isocyanate

74-93-1 Methyl Mercaptan

79-84-4 Methyl Vinyl Ketone

75-79-6 Methyltrichlorosilane

13463-39-3 Nickel Carbonly (Nickel tetracarbonyl)

7697-37-2 Nitric Acid (94.5% by wt. Or >)

10102-43-9 Nitric Oxide

100-01-6 Nitroaniline (paranitroaniline)

75-52-5 Nitromethane

10102-44-0 Nitrogen Dioxide

10102-44-0 Nitrogen Oxides (NO; NO(2); N204; N203)

10544-72-6 Nitrogen Tetroxide (also called Nitrogen Peroxide)

7783-54-2 Nitrogen Trifluoride

10544-73-7 Nitrogen Trioxide

8014-94-7 Oleum (65% to 80% by weight; also called Fuming Sulfuric acid)

20816-12-0 osmium Tetroxide

7783-41-7 oxygen Difluoride (Fluorine Monoxide)

10028-15-6 Ozone

19624-22-7 Pentaborane

79-21-0 Peracetic Acid (concentration >60% Acetic Acid; also called Peroxyacetic Acid)

7601-90-3 Perchloric Acid (concentration >60%)

594-42-3 Perchloromethyl Mercaptan

7616-94-6 Perchloryl Fluoride

79-21-0 Peroxyacetic Acid (concentration >60% Acetic Acid; also called Peracetic Acid)

75-44-5 Phosgene (also called Carbonyl chloride)

7803-51-2 Phosphine (Hydrogen phosphide)

10025-87-3 Phosphorus Oxychloride (also called Phosphoryl Chloride)

7719-12-2 Phosphorus Trichloride

10025-87-3 Phosphoryl Chloride (also called Phosphorus Oxychloride)

106-96-7 Propargyl Bromide

627-3-4 Propyl Nitrate

107-44-8 Sarin

7783-79-1 Selenium Hexafluoride

7803-52-3 Stibine (Antimony Hydride)

7446-09-5 Sulfur Dioxide (liquid)

5714-22-7 Sulfur Pentafluoride

7783-60-0 Sulfur Tetrafluoride

7446-11-9 Sulfur Trioxide (also called Sulfuric Anhydride)

7446-11-9 Sulfuric Anhydride (also called Sulfur Trioxide)

7783-80-4 Tellurium Hexafluoride

116-14-3 Tetrafluoroethylene

10036-47-2 Tetrafluorohydrazine

75-74-1 Tetramethyl Lead

7719-09-7 Thionyl Chloride

1558-25-4 Trichloro (chloromethyl) Silane

27137-85-5 Trichloro (dichlorophenyl) Silane

10025-78-2 Trichlorosilane

79-38-9 Trifluorochloroethylene

407-25-0 Trifluoroacetic anhydride

2487-90-3 Trimethoxysilane

Appendix E - Acutely Toxic ChemicalsBased on OSHA Standard 29 CFR, 1910.119, Appendix A.

CHEMICAL LOOKUP # CHEMICAL NAMES

75-07-0 Acetaldehyde

107-02-8 Acrolein (2-Propenal)

814-68-6 Acrylyl Chloride

107-05-1 Allyl Chloride

107-11-9 Allylamine

Varies Alkylaluminums

7664-41-7 Ammonia, Anhydrous

7664-41-7 Ammonia solutions (greater than 44% ammonia by weight)

7790-98-9 Ammonium Perchlorate

7787-36-2 Ammonium Permanganate

7784-42-1 Arsine (also called Arsenic Hydride)

542-88-1 Bis(Chloromethyl) Ether

10294-34-5 Boron Trichloride

7637-07-2 Boron Trifluoride

7726-95-6 Bromine

13863-41-7 Bromine Chloride

7789-30-2 Bromine Pentafluoride

7787-71-5 Bromine Trifluoride

106-96-7 3-Bromopropyne (also called Propargyl Bromide)

75-91-2 Butyl Hydroperoxide (Tertiary)

614-45-9 Butyl Perbenzoate (Tertiary)

75-44-5 Carbonyl Chloride (see Phosgene)

353-50-4 Carbonyl Fluoride

9004-70-0 Cellulose Nitrate (Concentration greater than 12.6% nitrogen)

7782-50-5 Chlorine

10049-04-4 Chlorine Dioxide

13637-63-3 Chlorine Pentrafluoride

7790-91-2 Chlorine Trifluoride

96-10-6 Chlorodiethylaluminum (also called Diethylaluminum Chloride)

97-00-7 1-Chloro-2,4-Dinitrobenzene

107-30-2 Chloromethyl Methyl Ether

76-06-2 Chloropicrin

None Chloropicrin and Methylbromide Mixt.

None Chloropicrin and Methylchloride Mixt.

80-15-9 Commune Hydroperoxide

460-19-5 Cyanogen

506-77-4 Cyanogen Chloride

675-14-9 Cyanuric Fluoride

110-22-5 Diacetyl Peroxide (concentration greater than 70%)

334-88-3 Diazomethane

94-36-0 Dibenzoyl Peroxide

19287-45-7 Diborane

110-05-4 Dibutyl Peroxide (Tertiary)

7572-29-4 Dichloro Acetylene

4109-96-0 Dichlorosilane

557-20-0 Diethylzinc

105-64-6 Diisopropyl Peroxydicarbonate

105-74-8 Dilauroyl Peroxide

75-78-5 Dimethyldichlorosilane

57-14-7 Dimethylhydrazine, 1,1-

124-40-3 Dimethylamine, Anhydrous

97-02-9 Dinitroaniline-2,4

1338-23-4 Ethyl Methyl Ketone Peroxide (also Methyl Ethyl Ketone Peroxide; concentration > 60%)

109-95-5 Ethyl Nitrite

75-04-7 Ethylamine

371-62-0 Ethylene Fluorohydrin

75-21-8 Ethylene oxide

151-56-4 Ethyleneimine

7782-41-4 Fluorine

50-00-0 Formaldehyde (Formalin)

110-00-9 Furan

684-16-2 Hexafluoroacetone

7647-01-0 Hydrochloric Acid, Anhydrous

7664-39-3 Hydrofluoric Acid, Anhydrous

10035-10-6 Hydrogen Bromide

7647-01-0 Hydrogen Chloride

74-90-8 Hydrogen Cyanide, Anhydrous

7664-39-3 Hydrogen Fluoride

7722-84-1 Hydrogen Peroxide (52% by wt or >)

7783-07-5 Hydrogen Selenide

7783-06-4 Hydrogen Sulfide

7803-49-8 Hydroxylamine

13463-40-6 Iron, Pentacarbonyl

75-31-0 Isopropylamine

463-51-4 Ketene

78-85-3 Methacrylaldehyde

920-46-7 Methacryloyl Chloride

30674-80-7 Methacryloyloxyethyl Isocyanate

126-98-7 Methyl Acrylonitrile

74-89-5 Methylamine, Anhydrous

74-83-9 Methyl Bromide

74-87-3 Methyl Chloride

79-22-1 Methyl Chloroformate

1338-23-4 Methyl Ethyl Ketone Peroxide (concentration > 60%)

453-18-9 Methyl Fluoroacetate

421-20-5 Methyl Fluorosulfate

60-34-4 Methyl Hydrazine

74-88-4 Methyl Iodide

624-83-9 Methyl Isocyanate

74-93-1 Methyl Mercaptan

79-84-4 Methyl Vinyl Ketone

75-79-6 Methyltrichlorosilane

13463-39-3 Nickel Carbonly (Nickel tetracarbonyl)

7697-37-2 Nitric Acid (94.5% by wt. Or >)

10102-43-9 Nitric Oxide

100-01-6 Nitroaniline (paranitroaniline)

75-52-5 Nitromethane

10102-44-0 Nitrogen Dioxide

10102-44-0 Nitrogen Oxides (NO; NO(2); N204; N203)

10544-72-6 Nitrogen Tetroxide (also called Nitrogen Peroxide)

7783-54-2 Nitrogen Trifluoride

10544-73-7 Nitrogen Trioxide

8014-94-7 Oleum (65% to 80% by weight; also called Fuming Sulfuric acid)

20816-12-0 osmium Tetroxide

7783-41-7 oxygen Difluoride (Fluorine Monoxide)

10028-15-6 Ozone

19624-22-7 Pentaborane

79-21-0 Peracetic Acid (concentration >60% Acetic Acid; also called Peroxyacetic Acid)

7601-90-3 Perchloric Acid (concentration >60%)

594-42-3 Perchloromethyl Mercaptan

7616-94-6 Perchloryl Fluoride

79-21-0 Peroxyacetic Acid (concentration >60% Acetic Acid; also called Peracetic Acid)

75-44-5 Phosgene (also called Carbonyl chloride)

7803-51-2 Phosphine (Hydrogen phosphide)

10025-87-3 Phosphorus Oxychloride (also called Phosphoryl Chloride)

7719-12-2 Phosphorus Trichloride

10025-87-3 Phosphoryl Chloride (also called Phosphorus Oxychloride)

106-96-7 Propargyl Bromide

627-3-4 Propyl Nitrate

107-44-8 Sarin

7783-79-1 Selenium Hexafluoride

7803-52-3 Stibine (Antimony Hydride)

7446-09-5 Sulfur Dioxide (liquid)

5714-22-7 Sulfur Pentafluoride

7783-60-0 Sulfur Tetrafluoride

7446-11-9 Sulfur Trioxide (also called Sulfuric Anhydride)

7446-11-9 Sulfuric Anhydride (also called Sulfur Trioxide)

7783-80-4 Tellurium Hexafluoride

116-14-3 Tetrafluoroethylene

10036-47-2 Tetrafluorohydrazine

75-74-1 Tetramethyl Lead

7719-09-7 Thionyl Chloride

1558-25-4 Trichloro (chloromethyl) Silane

27137-85-5 Trichloro (dichlorophenyl) Silane

10025-78-2 Trichlorosilane

79-38-9 Trifluorochloroethylene

407-25-0 Trifluoroacetic anhydride

2487-90-3 Trimethoxysilane

Appendix G - Glassware Used For Drug Making"Chemical laboratory apparatus" means any item of equipment designed, made, or adapted to manufacture a controlled substance or a controlledsubstance analogue, including:

a condenser;a distilling apparatus;a vacuum drier;a three-neck or distilling flask;a tableting machine;an encapsulating machine;a filter, Buchner, or separatory funnel;an Erlenmeyer, two-neck, or single-neck flask;a round-bottom, Florence, thermometer, or filtering flask;a Soxhlet extractor;a transformer;a flask heater;a heating mantel; oran adaptor tube.

NotesAppendices A and D list the known carcinogens and the acute toxic chemicals as per OSHA regulations. These materials must be inventoried andproper SOP (standard operating procedures) developed to insure that they are being properly handled and that the environmental controls areworking correctly.Please contact the Chemical Hygiene Officer (x4429) if any of the above chemicals are in your laboratories. An inventory form will be availablefrom the Risk Management Services group as well as on our WEBSITE ( ). Please fill out the form, inputting all of thehttp://www.web2.edu/riskmanchemicals that are either known carcinogens or are on the acute toxic chemical list (Appendix D).

Appendix I - Laboratory Safety Rules and Best PracticesNavigation

IntroductionObjectiveUnsafe or Harmful Acts and ConditionsBest Practices

Incident Reporting and General ComplianceGeneral HousekeepingPersonal ProtectionLab PracticesSafety EquipmentHazardous MaterialsChemical Use and StorageFlammable MaterialsInfectious or Potentially Infectious MaterialsSigns and LabelingTraining, Records and Access to Safety Manuals

IntroductionLaboratory safety is critically important to all who are responsible for or who work in and around laboratories. Although laboratory types andfunctions can differ, there are basic rules and best practices that can be implemented and observed in all laboratories, helping to improve overalllaboratory performance, while protecting the health and safety of all involved.

ObjectiveThe objective of these rules and practices is to promote a basic level of safety awareness and to encourage proper work practices in laboratories.These practices apply to all types of laboratories; however, many laboratories require additional rules and procedures specific to the risks andactivities undertaken and the particular material(s) and equipment in use.

Contact the Principal Investigator, Laboratory Supervisor or Laboratory Safety Officer responsible for your laboratory if you have additionalquestions or concerns, or Risk Management Services (RMS) at 940-565-4919.

Unsafe or Harmful Acts and ConditionsSafety is an important aspect of any properly functioning laboratory. Protecting those in and around a laboratory, laboratory equipment, and thesurrounding environment are critical components to effective prevention programs.

The rules and best practices contained in this document serve to demonstrate only the basic levels of safety required to ensure safe laboratoryactivities. All laboratory personnel are to be mindful of the ramifications of their actions, and work carefully and particularly to avoid, minimize ormitigate negative outcomes that may cause injury, death, property damage, and/or harm the environment.

In light of the impossibility to cover any and all hazards and exposures arising from laboratory materials and activities with this and other safetymanuals, it is , when not required by the type of chemical (such as carcinogens and extremely hazardous materials), thatstrongly recommendedlaboratories develop standard operating procedures and written protocols to guide workers in safely working with materials, equipment andconditions within the laboratory.

In addition, at times during inspections or otherwise, unsafe acts or conditions observed by or reported to Risk Management Services may beinvestigated, and remediation shall be required, with steps implemented to prevent unnecessary risks to life, property, and the environment. Tothis end, unsafe acts and conditions not explicitly covered by these rules and best practices, or contained within the Chemical Hygiene Plan orother safety manuals, are to be considered issues requiring a response following an inspection and/or report.

Best PracticesThe best practices contained in this guide are broken into the following key areas:

Incident Reporting and General Compliance

FactHuman error, poor laboratory techniques and misuse of equipment cause the majority of laboratory injuries and work related infections.

1.

2. 3.

4.

1. 2. 3. 4. 5. 6.

1. 2. 3.

4. 5.

1. 2. 3. 4.

1. 2. 3. 4. 5. 6.

1.

2.

General HousekeepingPersonal ProtectionLab PracticesSafety EquipmentHazardous MaterialsChemical Use and StorageFlammable MaterialsInfectious or Potentially Infectious MaterialsSigns and LabelingTraining, Records and Access to Safety Manuals

Incident Reporting and General Compliance

Within 24 hours (unless otherwise noted in list) all incidents listed below must be reported to the Chemical Hygiene/Biosafety Officer (pet):[email protected]

hazardous materials or related reagentsunsafe act or condition that may cause injury, death, property damage, or environmental harminjuries and/or cutsmissing or stolen materials (non-hazardous and uncontrolled substances, one week)misuse or abuse of chemicals and/or materials, including Personal Protective Equipment (next business day)use of spill kit, to request resupply (next business day)

Report changes in laboratory contact information to RMS by next business day (940-565-4919).Overnight experiments are required to inform Principal Investigator (PI) responsible for laboratory, post on main entry to lab,notice formand email completed form to the Chemical Hygiene Officer ( )[email protected] laboratory chemical inventories are recommended.

General Housekeeping

Aisles and walkways are to be kept clear and free of all tripping hazards at all times.High shelves, when in use, should never store items which might fall and injure, or are difficult to move or carry.Storage on high shelves cannot be closer than 24" to the ceiling in non-sprinkled buildings (18" in sprinkled buildings).Where floors are subject to wet conditions, proper precautions and safeguards (mats, drains, etc...) are required to prevent slip hazards.Empty containers, boxes, and broken equipment are to be promptly removed and discarded.Emergency exits are never to be blocked or poorly accessible.

Personal Protection

Personal Protection Equipment (PPE) appropriate for experiments should be worn at all times in the laboratory.PPE is required to be worn by personnel while working with hazardous materials.Reusable PPE is to be kept in good condition and discarded when cracked, torn, or otherwise damaged in such a way as to compromiseprotection.Disposable PPE should always be available in sufficient quantities for daily use by personnel.Laboratory personnel are required to wear closed-toed shoes and dress sufficient to cover legs (no shorts, skirts, etc...).

Lab Practices

Gloves should always be disposed of promptly in a manner according to use (biological, chemical, etc...).Laboratory personnel are not to eat or drink in the laboratory.Fume hoods are required to be used when handling hazardous materials.Maintenance and recordkeeping of controlled substances is to be observed at all times.

Safety Equipment

Eye wash stations are to be accessible and clear of obstructions.Eye wash stations are to be inspected, maintained and tested regularly, including testing for sufficient pressure to effect operation.Safety showers are to be accessible and clear of obstructions.Safety showers are to be inspected, maintained, and tested regularly.Chemical spill response supplies are to be available and replaced promptly when consumed.Care should be taken not to compromise the performance of the fume hood through improper use; for more information, see Chemical

.Fume Hood Safety

Hazardous Materials

Hazardous materials are required to be disposed of properly; for inquiries, contact RMS at 940-565-4919, or to request a pickup go to htt.p://rms.unt.edu

2. 3. 4. 5.

1. 2.

3.

4. 5. 6.

7. 8.

1. 2.

3. 4.

1. 2. 3.

4.

1. 2. 3. 4.

1. 2. 3.

Hazardous waste is to be removed as promptly as possible and never accumulated beyond what is necessary.Hazardous materials are required to be properly labeled.Sharps containers are provided for use and required for sharps materials.Broken glass is required to be placed into an appropriate broken glass receptacle.

Chemical Use and Storage

Incompatible materials and substances are always to be properly segregated.Hazardous materials are never be stored with materials meant to be eaten; refrigerators are not to be used dually to store chemicals andmaterials with food or drink.All high-pressure cylinders are to be securely fastened and with appropriate safety precautions at all times; transport of cylinders is to beaccomplished with the use of an appropriate dolly or device designed to transport the type of cylinder to be moved.Cylinders not in use are to be capped.Fume hoods are only to be used to keep chemicals in use during an experiment, and not for storage reasons.Hazardous materials are only to be available in the quantity needed for the experiment in process; quantities in excess of one quart/pint(depending on type) are not to be stored on the laboratory bench.Hazardous materials and reagents are never to be stored on the floor.Chemicals are required to be labeled with the full name and target organs of the chemical.

Flammable Materials

Flammable materials are only to be kept in the quantity required for the experiment.Flammable materials storage cabinets are required when storing flammable materials, except flammable liquids, which are required to bestored in an explosion-proof refrigerator.Flammable material quantities in excess of one quart are not allowed.Flammable materials are always to be kept sufficiently far enough away from an ignition source so as not to introduce an explosionhazard.

Infectious or Potentially Infectious Materials

Biohazards are allowed to be used only after a written protocol has been developed.With a written protocol, all biohazard use is to strictly follow that written protocol.Sterilized biohazard bags are to be disposed of properly according to the written protocol, and never by placing in unmarked bags or byremoving/obscuring biohazard labeling.Proper biohazard warning labels identifying biohazardous agents or biohazard areas are required.

Signs and Labeling

Clean areas are to be clearly marked and identified.Emergency call lists are to be posted at all doors to laboratory.Laboratory refrigerators, freezers, and/or microwaves are to be labeled 'Not for Food Use/Flammable Liquids'.Restricted areas, when required, are to be properly identified and secured.

Training, Records and Access to Safety Manuals

Personnel training sign off sheets are to be kept on file.Regular training (DVD, tape, online) is to be performed as needed/required.Chemical Hygiene and Biosafety Plans are available and personnel are to be made aware of how to access (online).

1.

1. 2.

1.

2.

Appendix J - Self-Assessment TrainingTable of Contents

IntroductionSafety Training Course

Art SafetyBiological SafetyBlood-borne PathogensBSL2 SafetyChemical Fume HoodChemical SafetyCleanroom SafetyEthidium BromideLaboratory WasteHydrofluoric Acid SafetyPyrophoric SafetyHazmat Transportation Safety

IntroductionThe following guide lists training requirements associated with related activities. Participant must identify any special training related to theiractivities. The training courses listed are mandatory lab/workplace safety training for all the UNT employees, scientists, researchers, TA's, andRA's.

Safety Training Course

Art Safetyhttps://riskmanagement.unt.edu/riskman/index.php?section=onlinetraining&group=artsafety

Frequency of training Biennial

If you...

Use art materials, paints, solvents, woodwork, sculptures, metals, etc., or major in Art.

Biological Safetyhttps://riskmanagement.unt.edu/riskman/index.php?section=onlinetraining&group=biosafety


If you...

Use biological materials, recombinant DNA, or toxins requiring BSL1 or BSL2 containment.Supervise a laboratory that uses biological or recombinant DNA, or toxins requiring BSL1 or BSL2 containment.

Blood-borne Pathogenshttps://riskmanagement.unt.edu/riskman/index.php?section=onlinetraining&group=bloodborne

Frequency of training Annual

If you...

Perform research with HIV or HBV, use human blood, cadaver, body fluids, human cells, human cell lines, work with patients, or handlepatient samples.

2. 3. 4.

1. 2.

1.

1. 2. 3. 4.

1.

1.

Ship or prepare to ship infectious agents (human, animal or plant), genetically modified organisms, human specimens.Enter biological research labs to provide maintenance or serviceRepair equipment from biological research labs as a non-researcher providing a service.

BSL2 Safetyhttps://riskmanagement.unt.edu/riskman/index.2.php?section=onlinetraining&group=biosafetyleveltwo


If you...

Use biological materials, recombinant DNA, human blood, tissues, body fluids, infectious agents, or toxins requiring BSL2 containment.Supervise a laboratory that uses biological or recombinant DNA, human blood, tissues, body fluids, infectious agents, or toxins requiringBSL2 containment.

Chemical Fume Hoodhttps://riskmanagement.unt.edu/riskman/index.php?section=onlinetraining&group=chemicalfumehood


If you...

Use hazardous chemicals in a laboratory or workplace.

Chemical Safetyhttps://riskmanagement.unt.edu/riskman/index.php?section=onlinetraining&group=labsafetyv


If you...

Use potentially hazardous chemicals or nonhazardous chemicals in a laboratory.Supervise students/employees using potentially hazardous chemicals in a laboratory, i.e. PI/manager, RA, TA, supervisor.Use potentially hazardous chemicals in a work place other than a laboratory.Supervise workers in the workplace, i.e. PI/supervisor.

Cleanroom SafetyUsers or cleanrooms should also see the Chemical Safety and Hydrofluoric Safety training sections.

Frequency of Training Annual

If you...

Use a cleanroom (take training before initial use)

Ethidium Bromidehttps://riskmanagement.unt.edu/riskman/index.php?section=onlinetraining&group=ethidiumbromide


If you...

Use Ethidium Bromide for staining DNA/RNA, or cell biology in a laboratory.

1. 2.

1.

1.

1.

Laboratory Wastehttps://riskmanagement.unt.edu/riskman/index.2.php?section=onlinetraining&group=laboratorywaste


If you...

Handle hazardous chemicals and infectious agents in the laboratory.Are laboratory personnel handling hazardous wastes daily.

Hydrofluoric Acid Safetyhttps://riskmanagement.unt.edu/riskman/index.php?section=onlinetraining&group=hydrofluoricacid


If you...

Use hydrofluoric acid in a laboratory or work place.

Pyrophoric Safetyhttps://riskmanagement.unt.edu/riskman/index.php?section=onlinetraining&group=pyrophoricsafety


If you...

Use pyrophoric chemicals in a laboratory.

Hazmat Transportation Safetyhttps://riskmanagement.unt.edu/riskman/index.2.php?section=onlinetraining&group=hazmattransportation


If you...

Ship or prepare to ship infectious agents (human, animal or plant), genetically modified organisms, human specimens, or hazardouschemicals.

1. 2. 3. 4.

Appendix K - Use and Storage of Laboratory CylindersTable of Contents

PurposeDefinitionsResponsibilitiesCylinders with Special RequirementsGeneral Protocols and Procedures

Laboratory Inspections“In Use” Cylinder RequirementsCylinder Delivery and Pickup

Cylinder InstallationCylinder Storage

Approved Cylinder Storage AreaSegregationReserve CylindersSpecial Uses and StorageNitrogen/Argon Large Volume Uses“Empty” Cylinders

References

PurposeThe proper use and storage of liquefied and gas cylinders are a critical safety measure for all laboratories to observe. Although cylinders areroutinely used without incident, cylinders have the potential to cause serious harm to people, the environment and the property of the university,and due care must always be observed when handling, using and storing cylinders.

The following protocol and procedures have been developed to enumerate requirements that all laboratories shall follow in the safe handling ofcompressed or liquefied gas cylinders. No exceptions to this protocol will be allowed.

DefinitionsCylinder – A tank or pressure vessel used to store liquefied or gas cylinders at or above atmospheric pressure.

Bottle – A cylinder containing high pressure gas.

Lecture bottle – A small compressed or liquefied gas cylinder, 12-18 inches long and 2-3 inches in diameter.

Non-lecture bottle – A cylinder of varying size, greater than a lecture bottle, containing compressed or liquefied gas at high compression.

Hazardous cylinder – A cylinder exhibiting a characteristic that is considered to be a “hazardous” cylinder will have at least one of the followingcharacteristics:

A health hazard rating of 3 or 4A health hazard rating of 2 without physiological warning propertiesAny pyrophoric gasAny explosive gas

“In use” – A cylinder connected through a regulator or to a manifold to deliver gas to a laboratory operation.

Reserve cylinders – A single cylinder secured alongside another, “in use” cylinder, to be used as a reserve for that cylinder.

Laboratory – A room or space provided for instructional, observation, measurement or other research activities in a non-production environment.For the purposes of this document, closets, chaseways and other service areas are not included in the definition of a laboratory (see “servicearea” definition below). This definition is based on the laboratory definition.Chemical Hygiene Plan

Service area – A closet, chase way or other designated area used to wholly or partially support a laboratory as defined in this document.

ResponsibilitiesPrincipal Investigators and laboratory staff/supervisors – Responsible for overseeing or performing proper installation of a gas cylinder into aregulator or manifold, for overseeing or performing proper and safe storage and transport of gas cylinders while in possession of a gas cylinder,and for training responsible laboratory staff and students in the proper handling, transport and storage of cylinders.

Laboratory staff – Employees, to include graduate students and teaching assistants, are to observe all rules and requirements for the handling,transport and storage of cylinders according to the safety rules enumerated in this document. Laboratory staff shall participate in required trainingprovided by laboratory management, and report issues and incidents concerning gas cylinders immediately to supervisors.

Laboratory inspectors – During all inspections, cylinders are to be reviewed for all conditions and requirements given within this protocol. Anyinfractions or concerns shall be recorded and followed up with a timely re-inspection. At no time is an infraction or unsafe condition to beundocumented due to immediate remediation of the concern by laboratory staff.

Risk Management Services – RMS laboratory safety staff are to monitor all inspections and provide follow-up inspections of laboratories withdocumented unsafe cylinder conditions or usage as given in this document. When necessary, RMS may perform training or require training onthis protocol to laboratories that exhibit a high degree of unsafe conditions or exhibit continuous problems over a period of inspections.

Cylinders with Special RequirementsSpecial requirements must be followed when storing a cylinder that contains a hazardous material.

Lecture bottle – A hazardous lecture bottle not “in use” (e.g., connected into a regulator or manifold) must be stored in a continuouslymechanically ventilated enclosure. A properly maintained and functioning fume hood meets this requirement. A bracket or clamp must be used tosecure the lecture bottle and keep tubing and piping from supporting the cylinder’s weight.

Non-lecture bottle – A hazardous cylinder greater than lecture bottle size may not be installed or stored anywhere but in a gas cabinet orapproved gas cylinder storage area, prohibiting covered cylinders of these types from being stored as reserve cylinders in a laboratory, closet orother service area. In addition, hazardous cylinders in this category containing pyrophoric gases are required to have sprinkled gas cabinets.

General Protocols and Procedures

Laborat

UNT Chemical Hygiene Plan · 2018. 12. 3. · UNT Overnight Experiment Notice Form Laboratory...

Documents

Transcript of UNT Chemical Hygiene Plan · 2018. 12. 3. · UNT Overnight Experiment Notice Form Laboratory...