Universal Storage - Ganging Locker to Locker and Locker to ... · Page 4 of 6 939503234 Rev C 2...
Transcript of Universal Storage - Ganging Locker to Locker and Locker to ... · Page 4 of 6 939503234 Rev C 2...
Page 1 of 6939503234 Rev C
®
If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com© 2003 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.
Printed in U.S.A.
Universal Storage - Ganging Locker to Lockerand Locker to Vertical File
ACR2 BIT
7/32"SOCKETWRENCH
1-3/8"OPEN ENDWRENCH
Locker Attached to a Locker
Locker Attached to a Vertical File
Page Topic
2-3 Ganging Lockers
4-5 Ganging a Locker to a Vertical File
6 Removal of Drawers from the Suspension
Table of Contents
Page 2 of 7939503234 Rev C
Ganging Lockers
1. Drill two (2) holes in the side of the top.
2. Place the two (2) lockers on their back and push lockers together (2a). After the lockers are together, remove the four (4) inner glides (2b).
3. Gang the two (2) lockers together by attaching two (2) plates to underside of lockers. Attach each plate using two (2) screws.
2
3
Underside ofTowers
2b
1
Underside ofLockers
Page 3 of 6939503234 Rev C
4. Place lockers upright (4a) and open doors. Secure the top of lockers with two (2) nuts and bolts secured inside the top of the lockers (4b).
5. Adjust front two (2) glides to level each unit. Adjust using a 1-3/8" wrench (5a). Adjust back two (2) glides; first release weight from the glide. Adjust using a 7/32" socket driver. For proper stability, adjust glides until unit is level (5b).
6. Ganging Wood UnitsFor wood units, secure units using self-drilling screws. Screw through front and rear channels of the inner sides.
1-3/8" WRENCH
For BACK glide adjustment For FRONTglide adjustment
5b
GLIDE
5a
7/32" SOCKET
4b
4a
6
Wood Version
Page 4 of 6939503234 Rev C
2
Ganging a Locker to a Vertical File
1. Drill two (2) holes in the side of top.
2. Place the locker and vertical file on their back and push them together.
3. Gang the locker and vertical file together by attaching two (2) plates to underside of units. Attach each plate using two (2) screws.
3
Underside ofUnits
1
Page 5 of 6939503234 Rev C
4. Place locker and vertical file upright (4a) and open doors. Secure the top of locker/vertical file assembly with two (2) nuts and bolts secured inside the top of the locker/vertical file assembly (4b).
5. Adjust front two (2) glides to level each unit. Adjust using a 1-3/8" wrench (5a). Remove the drawer in order to adjust the back glides (see page 6). Adjust back two (2) glides; first release weight from the glide. Adjust using a 7/32" socket driver. For proper stability, adjust glides until unit is level (5b).
6. Ganging Wood UnitsFor wood units, secure units using self-drilling screws. Screw through front and rear channels of the inner sides.
1-3/8" WRENCH
For BACK glide adjustment
For FRONT glide adjustment
5b
GLIDE
5a
7/32" SOCKET
4a
Note: For drawer removal, see page 6.
4b
6
Wood Version
Page 6 of 6939503234 Rev C
Removal of Drawers from the Suspension
1. Remove screws in the front on both sides of the drawer.
2. Pry out the suspension of the drawer at the eyebrow.
3. Lift drawer up and out of suspension belt loop.
4. Reverse for re-installation.
1
1
2
CAUTION:Screws must be re-installed in drawers.