Unit: Qty Rate Amount 1.0 Excavation for foundation up to 1.5M ...

TOURISM CORPORATION GUJARAT Ltd.

Sr.No. Description: Unit: Qty Rate Amount

1.0

Excavation for foundation up to 1.5M depth including

sorting of useful materials and disposing of the

excavated stuff up to 50 M. lead.

(A) Loose or soft soil.

Cu.M. 9000

b dense or Hard soil. Cu.M. 50

c Soft rock not required blasting Cu.M. 50

2.0

Excavation for foundation up to 1.5M to3.0M depth

including sorting out and stacking of useful materials

and disposing of the excavated stuff up to 50 M. lead.


Cu.M. 540



3.0

Excavation for foundation up to 3.0M to 5.0M depth

including sorting out and stacking of useful materials

and disposing of the excavated stuff up to 50 M. lead.


Cu.M. 10



4.0

Filling available excavated earth (Excluding rock) in

trenches, plinth, sides of foundation etc. in layers not

exceeding 20Cm. In depth consolidating each

deposited layer by ramming and watering.

Cu.M. 1230

5.0

Filling in foundation and plinth with murrum or

selected soil in layers of 20Cm. Thickness including

watering ramming and consolidating etc. complete.

Cu.M. 265.14

6.0

Boring holes up to 6.00 M deep in ordinary soil (for

cast in situ pipes) and disposal of the surplus excavated

soil as directed within any lead and lift. For following

diameter of piles minimum 2 nos of Bulb shall be

consider to any lead and lift..

(A) 200MM

mtr. 125

b 250MM mtr. 150

c 300MM mtr. 155

7.0

Extra for below 6.0 m depth but up to 9.00 mtr under

reaming inside the bore holes for under reamed piles'

of following diameter. Extra one Bulb shall be

consider(a) 200MM

mtr. 37.00

b 250MM mtr. 37.00

c 300MM mtr. 37.00

8.0

Filling with murrum or selected soil in layers of

300mm. Thickness including watering ramming and

consolidating etc. complete. CBR value shall not be

less then 10 (proctor density not less than 98%)

provide test before starting the P C C or B B CC

Cu.M. 63000

9.0

Conveyance Charges for civil debris like Lime,

Murrum, building dismantle brick work, concrete earth

manure or sludge and excavated rock and fly ash

(Assume) from the plot boundary

Leads:

a) up to 500mtr

Cu.M. 25

b from 500mtr to 1000 mtr Cu.M. 25

c from 1000mtr to 2000 mtr Cu.M. 25

d from 2000mtr to 3500 mtr Cu.M. 25

PACKAGE : 1 --- TRAFFIC & CROWD MANAGEMENT- BEAUTIFICATION OF APPR. ROAD-DEVELOPING

PARKING PLOTS-PUBLIC UTILITIES-ETC. AT DWARKA DIST: JAMNAGAR.

M/s. JAG Designers Pvt. Ltd. 1



e from 3500mtr to 5000 mtr Cu.M. 25

f from 5000mtr to onwards Cu.M. 25

10.0

Supplying, Stacking and Spreading of graded stone of

following size:

(a) Hand broken stone weight not less than 40.0kg

/m3. including conveyance, Stacking and spreading

charges.

Cu.M. 90

11.0Supplying, Stacking and Spreading of Murrumas

binding materialCu.M. 90

12.0

Rolling and Consolidating of soling including filling in

depression occurs during the process with Vibro roller

10 to 12 tonneand not exceeding 12 tone.

smt 100

13.0

Providing and laying cement concrete 1:4:8 (1-

Cement: 4-Coarse sand: 8-Hand broken stone

aggregate 40MM nominal size) and curing complete

excluding cost of formwork in

(A) Foundation and plinth.

Cu.M. 90

14.0

Providing and laying controlled cement concrete M-

150 and curing complete excluding the cost of

formwork and reinforcement for reinforced concrete

work in Command Rate

Cu.M. 2520

15.0




work in Common Rate

Cu.M. 1260

16.0




work in Common Rate

Cu.M. 330

17.0


250 exposed work with curing etc. complete including

the cost of form work but excluding the cost of

reinforcement for R.C.C. work at all level and all type

of concrete.

Common Rate

Cu.M. 30

18.0


250 for ornamental work including all cost of exposed

shuttering but excluding reinforcement work which

will be paid separately

Cu.M. 36

19.0

Providing and constructing Precast concrete pergola in

M-250 of having cross sectional area of 0.2 to 0.5sqm

and length up to 5.00mtr and fixing in position as

directed by architect or Engineer In-Charge different

sizes at different level.

Cu.M. 20

20.0


300 exposed work with curing etc. complete including

the cost of form work but excluding the cost of

reinforcement for R.C.C. work at all level and all type

of concrete.

Common Rate

Cu.M. 5

21.0 EXTRA COST FOR USING S.R. CEMENT cumt 1625

22.0

Providing H.Y.S.D. bar reinforcement for R.C.C. work

including bending, binding and placing in position

complete up to floor two level.

Kg 125750

23.0 EXTRA COST FOR USING C.R. STEEL Kg 125750




24.0

Brick work using common brunt clay building bricks

having crushing strength not less than 35Kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5 (1-

Cement: 5-fine sand) (A) Modular.

Cu.M. 50

25.0Extra for brick work in super structure above Plinth

level up to floor two level. (A) Modular. Cu.M. 35

26.0Extra for brick work in super structure above floor two

level. (A) Modular. [Item No. 1 [6.12-A]

Per floor Per

Cu.M.65

27.0

Half brick masonry in common brunt clay building

bricks having crushing strength not less than

35Kg./Sq.Cm. in Cement Mortar 1:4 (1-Cement: 4-

Course sand) in foundation and plinth.

(A) Modular.

Sq.M. 530.73

28.0

Extra for half brick masonry in super structure above

plinth level up to floor two level.

(A) Modular.

Sq.M. 35

29.0

Un-coursed rubble masonry with hard stone of

approved quality in foundation and plinth in Cement

Mortar 1:6(1-Cement: 6-Couse sand including leveling

up etc.complete.

Cu.M. 30

30.0

Providing formwork of ordinary timber planking so as

to give a rough finish including centering, shuttering,

strutting and propping etc. height of propping and

centering below supporting floor to ceiling not

exceeding 4M. And removal of the same for in situ.

reinforcement concrete and plain concrete work in all

type of structuer.COMMON RATE

smt 4874

31.0

Extra for additional height of propping and centering

where the height of propping and centering exceeds

4.0Mt. Between supporting floor to ceiling including

temporary brick or stone pillars for supporting as

required.(a) Height more than 4.0M and up to 5.0M

Sq.M. 90

a Height more than 5.0M and up to 6.0M. Sq.M. 90

b Height more than6.0M and up to 7.0M Sq.M. 90

32.0

EXPOSED for providing form of work with sheathing

of steel sheets so as to give a fair finish in

Common Rate (EXPOSED FINISHED)

Sq.M. 720

33.0

Providing and fixing 35MM thick shutters for doors,

windows and clearstory windows including Indian teak

wood frames 10Cm x 7Cm size including anodized

aluminum fixtures and fastening primer coat of

approved quality and two coat of oil painting etc.

complete.(a) Fully paneled

Sq.M. 30

34.0Add. Extra for providing and fxing 40MM thick

shutters instead of 35MM thick shutters.Sq.M. 30

35.0

Providing and fixing flush door shutters, solid core

construction with frame of first class hardwood with

cross band and face veneer or plywood face panels,

including anodized aluminum butt hinges with

necessary screws.

Sq.M. 54

36.0Extra for using bright finished M.S. piano hinges of

[A] Nickel plated piano hinges.Sq.M. 30




37.0

Providing and laying glazed tiles 6MM thick in

skirting, risers of steps and dedo on 10MM thick

Cement plaster 1:3(1-Cement: 3-Coarse sand) pointing

in white cement slurry. ( rate for 1st quality tiles )

Sq.M. 711

38.0

Providing and laying 25MM thick Kotah stone slab

flooring over 20MM (average) thick base of Cement

Mortar 1:6(1Cement: 6-Coarse sand) or Lime Mortar

1:1.5 laid and jointed with grey cement slurry

including rubbing and polishing complete.

[A] 25MM thick.

Sq.M. 36

39.0

Providing and laying Kotah stone slab 25MM thick in

risers of steps, dedo and pillars laid on 10MM thick

Cement Mortar 1:3(1-Cement ; 3-Coarse sand) and

jointed with gray cement slurry including rubbing and

polishing etc. complete.

Sq.M. 150

40.0

Providing and laying Rough chiseled dressed Kota

stone flooring over 20 mm. thick base of cement

mortar 1:4 (1 cement : 4 coarse sand) or L.M. 1:1.5

including pointing with cement mortar 1:2 (1 cement :

2 coarse sand) etc. complete.

(A) 25 mm.to 37 thick Rough Kota.

Sq.M 55

b25 mm.to 37 mm thick Red Mandana (non-slippery

finish).Sq.M 45

c 40 mm to 50mm. thick Rough Kota Sq.M 45

41.0

P/F basant beton make natural rough/polished cobble

coloured stones patterned with Shot blasted Granite 30

to 40 mm thick and 400 x 400 mm in size (in different

colour combination) if the same make to be used on

cement mortar bedding 1:4 (1 cement:4 coarse sand )

including joint filled up with coloured cement to match

the shade of stones approved by Architect as shown in

drawing.: T-TYP-CBS-01

sq.m 1186

42.0

Providing & fixing 80 mm thick inter locking paver

blocks using concrete grade M:400 for heavy

vehicular movement luster finish coloured stones (in

different colour combination) to be used in the parking

areas on 50 mm thick sand layer including mechanical

compaction as shown in drawing.: T-TYP-PAR-01

sq.m 9000

43.0

Providing & fixing at or near ground level precast

cement concrete kerbs, edging etc. setting in position

with cement mortar 1 : 2 ( 1 cement : 2 coarse sand)

including the cost of centring,shuttering and finishing.

rmt 479

44.0

Providing and fixing tiled roofing with Manglore tiles

including teak reapers of size 50MM x 25MM or as per

instruction by architect/Engineer In-Charge.

Sqm 171

45.0

Providing 10MM thick cement plaster in single coat on

Brick/concrete walls for interior plastering up to floor

two level finished even and smooth in

[A] Cement Mortar 1:3 (1-Cement: 3-Sand)

Sq.M. 530




46.0

Providing 15MM thick cement plaster in single coat on

Brick/concrete walls for interior plastering up to floor

two level finished even and smooth in

[A] Cement Mortar 1:3 (1-Cement: 3-Sand)

Sq.M. 10

47.0Extra over items 45 to 46 for finishing with a floating

coat of neat cement slurry.sqm 540

48.0

Extra over items 41 to 42. for providing and mixing

water proofing materials in cement Mortar in

proportion recommended by the manufacturer

Per beg of

50Kg. Of

Cement used

in Mix.

540

49.0

Painting two coats (excl. priming coat) on new steel &

other Metal surfacer with enamel paint, brushing,

interior to give an even shade incl. cleaning the surface

of all dirt, dust and other foreign matter. Special anti

corrosive paint.

Sq.M. 55

50.0

20MM thick sand faced cement plaster on walls up to

height 10meters above ground level consisting of

12MM thick backing coat of cement Mortar 1:3 (2-

Cement: 3-Sand) and 8MM thick finishing coat of

Cement Mortar 1:1 (1-Cement: 1-Sand) etc. complete.

Sq.M. 5

51.0

Distempering (Two coats) with oil bound washable

distemper of approved brand and manufacture and of

required shade on wall surfaces to give an even shade

over and including a priming coat of with alkali

resistance primer of approved brand after thoroughly

brushing the surface free from mortar droppings and

other foreign matter and also including preparing the

surface even and smooth.

Sq.M. 5

52.0

Demolition and disposal of unserviceable materials

with all lead and lift.

[A] Lime concrete.

Cu.M. 50

b Un-reinforced cement concrete. Cu.M. 40

53.0

Demolition including stacking of serviceable materials

and disposal of unserviceable materials with all lead

and lift.(A)R.C.C. work.

Cu.M. 25

54.0

Demolition of brick work and stone masonry including

stacking of serviceable materials and disposal of

unserviceable materials with all lead and lift in Lime

Mortar. [A] In Lime Mortar.

Cu.M. 40

b In Cement Mortar. Cu.M. 45

55.0

Demolition of terrace including stacking of serviceable

materials and disposal of unserviceable materials with

all lead and lift.

Brick tile covering.

Sq.M 110

56.0

Dismantling tiled or stone floors laid in mortar

including stacking of serviceable materials and

disposal of unserviceable materials with all lead and

lift.

Sq.M. 110

57.0

Dismantling of sheet roofing including ridges, hips,

valleys, gutters, etc. stacking of serviceable materials


[A] G.I. Sheet roofing.

Sq.M. 60

58.0Dismantling steel work including distempering and

stacking the materials with all lead and lift.Kg. 60




59.0

Dismantling doors, windows, ventilators etc. (Wood or

steel) shutters including chowkhats, Architraves,

Holdfasts and other attachment etc. complete and

stacking them within all lead and lift.

[A] Not exceeding 3-Sq.M in area.

Each 8

b Exceeding 3-Sq.M. in area. Each 8

60.0

Dismantling barbe wire in fencing including making

rolls and also including dismantling fencing posts

including all earth work concrete in base and making

good the disturbed ground stacking useful materils as

directed and disposing of the unserviceable materials


Metre 100

61.0

Dismantling C.I. pipes G.S.W. pipes and A.C. rain

water pipes with fittings and clamps including stacking

the materials with all lead and lift (for any dia. Of

pipe).

Metre 50

62.0

Dismantling sanitary fittings like wash basin, W.C. pan

Indian and European type, flushing tank etc. including

stacking the materials with all lead and lift.

Each 2

63.0

Providing and fixing M.S. fan clamps of shape and size

as specified in existing R.C.C. slab including cutting

chase and making good.

Each 5

64.0

Carrying out plinth treatment to post construction/

existing structure by spraying chemical solution for

termite control treatment including labour and

materials consist with I.S.I. specification.

Sq.M. 325

65.0

Providing laying (to level or slopes) and jointing

reinforced concrete light duty non-pressure pipes I.S.

class Np2 of the following internal diameter with

collars and butt ends prepared for collar joints

including testing of joints complete.(a) 150MM

Metre 10

b 250MM Metre 10

c 300MM Metre 10

d 450MM Metre 10

e 500MM Metre 10

f 600MM Metre 10

g 900MM Metre 10

h 1000MM Metre 10

i 1200MM Metre 10

66.0

Providing and laying water proofing treatment on

terrace including applying neat cement slurry 2.75

Kg./Sqmt on cement admixed with waterproofing

component after cleaning the surface, laying cement

concrete with brickbats 75 mm to 100 mm thick with

50% of C.M. 1:5 admixed with waterproofing

component over 20 mm thick layer of C.M.1:5 to

required slope including ramming at junction of wall

and slab, after two days of proper curing applying a

second coat of cement slurry, finished the surface with

20 mm thick C.M. 1:4 china mosaic flooring and

finally finished surface with terrace shall be finished

with water for a period of two week.

Sq.M 9




67.0

Providing and laying 200 mm thk Miyami Stone

Masonry, one side natural stone finish/or rough finish

smooth finished in CM1:3 with fix joint and 10mm

groove in stoneand chiseled in stone for mortar

bedding as per Ar.drawing and detail. Stone size

:425mm long x 200mm depth x 200 height for

uniform course). Finishing the masonary with

flush or v-notch cement pointing in 1:2 cm

cum 720

68.0

Providing and laying 400 mm thk Miyami Stone

Masonry, one side natural stone finish/or rough finish

smooth finished in CM1:3 with fix joint and 10mm

groove in stoneand chiseled in stone for mortar

bedding as per Ar.drawing and detail. Stone size

:425mm long x 200mm depth x 200 height for uniform

course)

cum 9

69.0

Providing and laying External Cladding Miami lime

stone, 15 to 25 mm thk (total 35mm including fixing

gap) honed finish including making groove, chiselled

for filling of mortar, including required anchoring

clamp, fixing & adhesive to finishing surface, finishing

complete (including temple parisar existing wall

cladding-no ornamentation)

Smt 1772

70.0

Providing and laying All Window sills and terrace

coping 100 mm thick (with 50x40mm cut) in Miami

lime stone honed finish including fixing, finishing

complete (with drip mould of 15x15mm size, groove &

slope in stone).

rmt 16

71.0

Providing and laying Miyami stone Cladding on RCC

Column 40-50 mm thk, in cm 1:3 with min. 20mm

thick, including making groove, chiselled for filling of

mortar, texture work(including exterior paint) in any

pattern, including fixing, holding with clamps, fixing,

adhesive & fasteners, finishing complete.

smt 440

72.0

Providing and applying stone treatment with

even and uniform spreading of two coats of

solvent based water impregnator (BAL,DUPONT, MC

Bakuchima approved make or equivalent) on all stone

surfaces including cleaning of any deposits on stone

surface before application for all stone work, to be

approved by Architect./Engineer In-Charge

smt 1100

73.0

Providing and laying 230mm thick rubble soiling

including filling the voids with yellow earth, including

watering rolling with 8 to 10MT vibro roller etc.

complete as per the instruction by Engineer In-Charge

cmt 2462

74.0

Providing and fixing of stone piller as per locally

available of white lime stone and complete with all

related civil work As shown in drawing.:T-TYP-SPL-

01

Nos. 200




75.0

Providing and fixing Signages at (A)Main Enterance as

shown in the drawing which consist of White Lime

stone pillars, stone slab with the letters / text(in

Gujarati/Hindi/English/Sanskrit),including all

necessary carving work on it as per detail, as shown,

complete with erection , etc WITH ALL RELATED

CIVIL WORK. 3.41 x 1.25 mt. ref. drawing no : T-

TYP-SIN-01

Each 1

b 1.5 x 0.90 mtr. Ref. drawing no: T-TYP-SIN-01 Each 3

76.0

Providing and fixing of dustbin of 0.95×0.95×1.48

made from white lime stone slabs with all inclusive of

complete civil and stone related items as per shown in

drw no. T-TYP-SDT-01

Each 10

77.0

providing and fixing of signage in S.S(316). of 0.45 x

0.25 mt. complete with all text shown as per drawing

no. T-TYP-SIN-01

Each 25

78.0

Providing and fixing in position doors with jindal-4648

63.50mm*49.50mm frame size, including 3 nos. of

heavy duty S.S. butt hinges on each shutters, M.S.

screws with roll plug and inside wooden BWP Flush

door of 750*2100 with 150*37mm top,200*37mm

bottom, 150*37mm lock rails and both sides 12

prelaminated finish (shutter wood up to 30 DM/Smt) as

per design and with either side fix wooden panel of

19mm fix W.p. ply with both side laminate finish as

required including necessary hardware and fixing

arrangement melamine polish of approved make and

shade complete including anty termite treatment to

wood etc. complete

Sq.M 5

79.0

Providing and laying over dacking insulation for all

building terrace with surface to be clean and free from

all dust,dirt,grease etc.INSULITTE-a light weight

aggregate is to be mixed manually or by machine

mixer for 2 or 3 minutes in proportion with cement as

per recommended dosage is 20.00kg/Smt and add

water to dry mixture and screed the mortar to desired

average thickness to maintain required slope and

lightly compacted evenly.Recomandation to prevent

this insulation layer cover with IPS, China Mosaic or

other type of water proofing material.

Sq.M 23

80.0

Polishing with Melamine polish on wooden door and

window to give an even surface and shade as per

Architect instruction including cleaning the surface of

all dirt, dust and smooth finished by sand papered and

including a coat of wood filler and final coat of polish

with Air compressor with hardener.

Sq.M 19

81.0

Providing and laying 30mm Kota polished stone slab(

sand witch type) Plate- form for base laid and jointed

with Colour cement slurry including rubbing and

polishing complete: no extra cost for the facia Patti

(A) Kota slab 30 mm. thick.

Sq.M 27




82.0

Providing and laying 20mm Granite Double polished

granite stone slab for Urinal Partition with fine

polished molded edges (front and Top) laid and jointed

with Colour cement slurry including rubbing and

polishing complete: size of portion 600mm x

1500mm(A) Granite slab 20 mm. thick.

Sq.M 45

83.0

Providing and laying Dressed white lime stone Stone

for different type of construction work like Masonry

work, Simple Rough Cladding, Column, Sill, Copping

Stone etc.work with various size and finish with CM

1:3 (1 part Cement : 3 part of Screen sand ) and

required Stainless Steel(S.S. 304) pins for joinery,

Adhesive with all required Scaffolding,

Fischer/Hilti(Anchore Bolt), tools and tackles for

cutting in shape including groove, polishing and all

finish as per Architecture drawing and Engineer in

Charge ( Stone Size :600*450*200 mm

,600*300*200mm, 450*230*200mm, 450*150*200

mm for Masonry work)

Cu.M 18

84.0

Providing and laying External Cladding white lime

stone/Miyami stone, 50 mm thick honed finish

including required anchoring clamp, fixing & adhesive

to finishing surface, finishing complete (existing wall

cladding-no ornamental work)

Cu.M 45

85.0

Providing and laying white lime stone,30 mm thick

honed finish including required anchoring clamp,

fixing & adhesive to finishing surface, finishing

complete (including temple parisar existing wall

cladding-no ornamentation)50 mm thick Fort type

dressed and cut edge wall as per instruction by

Architect/Engineer In-charge Above Column.

sqmt 10

86.0

Providing and laying white lime stone/miyami Stone

Ornamental solid stone or layers of stone 20-40mm

thick at Column , including hollow stones to receive

RCC from foundation, brackets at top to receive torans,

fixing and finishing complete

sqmt 27

87.0

Providing and Laying External Cladding 100 to 150

mm thick finish incl required screwing & finishing

surface to hide screw heads (including existing

premises, cladding at Temple Fort Interior wall &

River Edge wall also for fixing use adhesive and

anchor fastener as per detail.(provide anchored pull out

as when require)

Cu.M 45

88.0

Providing and laying S.S. Railing of 316 low carbon

steel grade as per instruction by architect/Engineer In-

charge, On every odd/even no., 40mm dia Vertical

pipe and 2nos of 25 mm dia Horizontal pipe with 50

mm dia top hand rail(Height of railing upto 900mm),

riveting and welding and fixing at floor with 100 dia or

square 5 mm thick base plate of S S 316 with hilty or

equivalent anchor bolt and other necessary fixture as

per approval of Architect/Engineer In-

charge.(Thickness of pipe is provide minimum 1.2 to

1.5mm)Provide pull out test of anchored bolt as when

Sq.M 45




89.0

Providing and fixing 10 gauge(in to in 25mm × 25mm)

weld mesh Jali including cleaning, rubbing with

suitable abraser, applying one coat of epoxy primer

and 3 coats of approved make of enamel paint as

directed. (Frame shall not be paid separately). As per

instruction by Architect/Engineer In-charge.

Sq.M 20

90.0

Providing and laying structural Steel work welded, in

built up sections, frame work including cutting,

hoisting, fixing in position and applying a priming

coat(Zinc cromate)and 3 coats of Enamale Paint of

Approved Make .(A)In beams and joists, channels

angles, tees, flats,Sag rod,round bar,twisted bar with

connecting plates or angle cleats as in main & cross

beam ship & bridge work.(all plates are will be profile

cut &all holes in plates channel, angle ,hollow section

etc must be by drilled only)

Kg 1350

91.0

Concrete M-35 Grade and 80 mm thick Rubber

Moulded paver block (Capacity 40 tonne/sqmtr)

pavement on 20 to 30 mm th sand bedding with pattern

and design as per Instruction by Architect/Engineer In-

charge, including finish with mechanical compactor.

As directed by Architect/Engineering In-Charge.

Sq.M 5

92.0

Providing, fabricating and fixing MS Railing / gate for

parking,etc. of required Pattern as per approved

drawing, design and direction to Steps or in

masonry/RCC/ Flooring with MS flats/square/round

Pipe and bars at required spacing and frame all around

fixed with Fasteners of Hilty or Approved quality to

including one coat of epoxy primer and three coats of

approved enamel paint etc. complete. Welding and

welding road to be approved from Architect (Structure

consultant) as shawn in drawing no.:T-TYP-GT-1,T-

TYP-PKG-1

Kg 180

93.0

Hand lorry(Push cart) to carry Garbage with 6nos. Of

PVC 25 ltrs. bucket container with two iron wheel and

making of Maniyar or equivalent make as per approved

by architect/Engineer In-charge.

No. 3

94.0

Providing and Applying Apex/Burger/Approved make

antifungal exterior wall paint 3 coats as per

manufacture specification of required shade to give an

even shade after thoroughly brushing the surface, free

from mortar, free from greese & other impurities& also

including prepared the surface even & smooth up to

satisfaction of Architect / Engineer in Charge Before

(starting the work shade must me passed from arch/site

in charge)

Sq.M 40

95.0

Providing and Applying Textured make antifungus

exterior 3 coats of wall paint as per manufacture

specification of required shade & textured to give an

even shade after thoroughly brushing the surface, free

from mortar, greese, and other impurities including

prepared the surface even & smooth upto satisfaction

of Architect / Engineer in Charge

Sq.M 135




96.0

Providing and laying Internal Wall painting 1coat of

primer,1 coat of wall putty of approved make, with

plastic emulsion paint of (3 coat) approved make. on

undercorated wall surface to give an even shade

including thoroughly brushing the surface free from

mortar greese,and other impurities & prepared smooth

surface as per instruction by Engineer In-Charge. rates

including cost of providing and applying primer and

putty.

Sq.M 180

97.0

Allu. Door(alluminium sections only of approved

Makes)Providing and fixing Aluminum Door frame

with fully paneled ( ACP or equi.) shutter of approved

make and design as directed by Architect, out of

extruded tubular hollow section size for frame approx.

63mm x 38mm x 3mm( w app = 0.901 kg/m), & For

the shutter 100mm x 44mmx 3mm ( w app = 1.60

kg/m)as top member and 114mm x 44 mmx3mm (

w.approx=1.83 kg/m) as middle and bottom member

and 48mm x 44mm x 3mm(w approx=1.05 kg/m) as

others vertical member and of the heavy quality

mechanically joined, double whether stripped with

brush type whether strips and with screw less bedding

including all the required hardware as per drawing and

door closer(approved Make) in matt anodized/Powder

coated 20 micron/60 micron minimum with approved

make 6 mm thick float glass, EPDM rubber shall be

used for fixing the glass etc. complete as per design,

specification and instruction of the

Consultant/Engineering In-charge. As shown in

Drawing No.:T-TYP-DW-01

smt 39

98.0

Allum. Vents(alluminum sections of approved make)

Providing and Fixing Aluminum heavy duty Louvers

made from 63.5mm x 38mm x 1.2mm( w app = 0.901

kg/m) and 20 micron anodized/60 micron powder

coated and other fixtures and fitting including 6mm

thick Bajaridana Glass/as per architect/Engineering In-

charge etc.completed.As shown in drawing.: T-TYP-

DW-01

smt 18

99.0

Internal wall putty ( Birla or equivalent) on wall and

Ceiling on mala finished/smooth finish plaster

removing all dirt, dust and other mortar drops etc.with

even and smooth finish for paint base.

smt 795

100.0

Providing and laying pointing at external area of

stone/Brick work maintain in 4 to 10mm wide and

10mm deep groove on every stone/Bricks layer as per

Architect/Engineer in-charge in CM 1:2 proportion.

sqm 955

101.0

Providing and fixing. Seating benches made from

Precast RCC Exposed surface in M 25 proportion.

Complete with all related civil work like excavation,

pcc, etc. as shown in drawing no: T-TYP-SBH-01

Nos. 9




102.0

Providing and constructing seating bench by using

rough kotah stone in bottom and polished kotah stone

on top with moulding edges of benches of shape and

size as shawn in the drawing complete with stone

masonary in CM 1:3 proportion support and

Excavation, P.C.C.etc complete, refer drawing no.T-

TYP-SAT-02

Rmt 27

103.0

Providing and fixing of Elephant 4.5 mtr. height at

Entrance Gate completed with all related civil work

required as shown in drawing ( In RCC + other

textured finishing )

Inclusive of excavation, pcc, rcc work , pigmented

Paint, concrete, pedestal, reinforcement, filling,

shuttering, plastering if req, pointing, stone work,

ornamental stone work, etc.As shown in drawing no.:T-

TCM-A1-02

Each 2

104.00

GABIONS - SANS 1200DK:1995 (Double twist

hexagonal wire mesh to

SANS 1580:2005) GABIONS (Including material and

delivery, fixing) Mesh Type 80 with 3.0mm Class A

Galvanized wire Length x Width x Height

cum 50

105.00 Surface preparation for bedding of Gabions cum 50

106.00Installation of Gabion units (Including unfolding,

placing, filling, lacing and bracing)cum 50

107.00 Rock fill cum 650

108.00 Packing selected stone for exposed face sqm 1890

109.00

AG GEOTEXTILE (Garware or equivalent)(Including

material, delivery, unrolling, cutting and placing)

Continuous Polyester Filament Double Needle-

Punched etc complete as per instruction of engineer in

charge/ consultant.(a)AG150 - Minimum Energy

Absorption - 4.0kN/m

sqm 50

b AG200 - Minimum Energy Absorption - 6.5kN/m sqm 100

c AG300 - Minimum Energy Absorption - 10kN/m sqm 2000

d AG400 - Minimum Energy Absorption - 12kN/m sqm 2650

110.0

Road Preparation of sub

grade by excavating earth to an average of 22.5 cm

depth, dressing to camber and consolidating with

vibro roller including making good the undulations

etc. and disposal of surplus earth lead upto 50

metres.Required proctor density test not less than

98%

sqm 1350

111.0

Consolidation of sub grade with vibratory road roller

of 8 to 12 tonne capacity including making good the

undulations etc. with quarry spoils etc. and rerolling

the sub grade.

sqm 1500

112.0

Laying water bound macadam sub-base with graded

stone aggregate 90 to 40mm size, stone screenings of

12.5mm size and blinding material including

screening, sorting, spreading to template and

consolidation with vibro roller etc. complete. (Payment

for stone aggregate, screenings, kankar, moorum and

red bajri etc. to be made separately.)

cum 747




113.0Supplying and stacking of graded stone aggregate of

size range 90mm to 40mm at sitecum 100

114.0

Laying water bound macadam base course with graded

stone aggregate 63 to 40mm including stone

screenings, blinding material and including screening,

sorting, spreading to template and consolidation with

vibro roller etc. complete. (Payment for stone

aggregate, screenings, red bajri etc. to be made

separately.)

cum 747

115.0Supplying and stacking of graded stone aggregate of

size range 63mm to 40mm at sitecum 63

116.0

Supplying and stacking of stone screening / chippings

at site.

(a) 12.5mm nominal size

cum 450

117.0

Providing and applying tack coat using hot straight run

bitumen of grade 80 / 100 including heating the

bitumen, spraying the bitumen with mechanically

operated spray unit fitted on bitumen boiler, cleaning

and preparing the existing road surface as per

specifications.(a) On W.B.M @ 0.75 Kg / sqm

sqm 300

118.0

Landscape (A) Excavation / Site grading

including site line-out and verification of

survey and proposed drawings to check for

irregularities, light irrigation by flooding,

removal of shrubs, weeds, debris, etc,

excavating upto 1.5m, grading and leveling,

stacking of excavated material and casting

upto any lead and lift.

Site clearing

sq.m. 985

b

Excavation up to 1.5m depth including

excavation, loading, unloading and casting

away of unwanted material upto any lead and

lift

cu.m. 90

c

Soil filling, grading, rolling, compaction, etc

complete up to 1.5m depth including loading,

unloading, supply of good quality soil as

specified if required

cu.m. 270




119.0

(A) Development of Trees including digging

of pits, pre-treating pits with anti-termite

insecticide, spreading excavated earth around

pits, filling good quality soil and FYM mix,

and planting each plant including supply of

necessary labour and equipment and supply,

carting, loading and storage of good quality

soil, fertilizer, termite treatment chemical,

weedicide, insecticide, FYM, etc stacking of

debris and casting upto any lead and lift as

specified but excluding the cost of the plant.

(a)Large sized trees: Pit size 1000 x 1000 x

1000mm

Nos 13

b

Medium sized trees, small sized trees, big

sized shrubs, palms, bamboos: Pit size 800

x800 x800mm

Nos 22

c Shrubs, creepers: 600 x 600 x 600mm Nos 31

dGround cover, bulbous plants, grass cover,

etcNos 135

120.0

Development of Hedge including digging of

500mm deep trench, pre-treating area with

insecticide for anti-termite treatment, filling

good quality soil and FYM mix, planting at

distances specified in drawing, regular

watering and weeding, etc including supply

of necessary labour and equipment and

supply, carting, loading and storage of good

quality soil, fertilizer, termite treatment

chemical, weedicide, insecticide, FYM, etc

stacking of debris and casting upto any lead

and lift as specified but excluding the cost of

the plant.

r.m. 100

121.0

Planting of low shrubs, plant pockets, etc

including excavation upto 300mm deep,

spreading good quality soil and FYM mix,

continuous weeding operations, pre-treating

area with anti-termite insecticide, planting of

plants as specified in drawings including

supply of necessary labour and equipment

and supply, carting, loading and storage of

good quality soil, fertilizer, termite treatment

chemical, weedicide, insecticide, FYM, etc

stacking of debris and casting upto any lead

and lift as specified but excluding the cost of

the plant.

sq.m. 891

122.0 Khair No. 9




123.0 Devbabool No. 9

124.0 Kunchandana(S), Thoraligunj No. 9

125.0 Bel, Bilva No. 9

126.0 Sirisha(S), Siris No. 9

127.0 Chikunda(S), Kala Siris No. 9

128.0 Allamanda dwarf No. 9

129.0 Aloe vera No. 9

130.0 Saptparni No. 9

131.0 Angelonia No. 9

132.0 Cadamba, Kadamba No. 9

133.0 Krishna guru No. 9

134.0 Phanas, Fanas No. 9

135.0 Arundinaria variegata No. 9

136.0 Neem, Margosa No. 36

137.0 Karunta(S)*, Koranti No. 2

138.0 Sivamalli(S)* No. 4

139.0 Rakta Chandan(S), Dev Kachanar No. 5

140.0 Svetakanchana(S) No. 6

141.0 Phalgu(S)* No. 7

142.0 Kovindrara(S), Kachanar No. 8

143.0 Scorpion lily No. 5

144.0 Bignonia megapotamica No. 5

145.0 Palash, Kesudo No. 5

146.0 Caesalpinia pulcherrima No. 5

147.0 Vet Vanjul No. 5

148.0 Calliandra No. 5

149.0 Callistemon lanceolatus No. 5

150.0 Nagachampi(S), Undi* No. 5

151.0 Akada, Rui, Ark No. 5

152.0 Carissa grandiflora No. 5

153.0 Charmaranga(S)*, Tarwad No. 5

154.0 Cassia Biflora No. 5

155.0 Suvarnaka (S)*, Amaltas, Bhava No. 5

156.0 Pinus Roxburghii No. 6

157.0 Areca Palm No. 27

158.0 Aparajita (S)*, Gokarna No. 18

159.0 Cordia sebestena No. 7

160.0 Varuna(S), Barna* No. 7

161.0 Crinum asiaticum No. 7

162.0 Haridra(S)*, Halad No. 7

163.0 Cynodon dactylon sq m 7

164.0 Umbrella Palm No. 36

165.0 Daedalacanthus nervosus No. 1

166.0 Madhavi, Atimukta (S)*, Malati No. 18

167.0 Day lily No. 18

168.0 Ipomea biloba No. 1




169.0 Ixora No. 1

170.0 Ixora chinensis No. 1

171.0 Jasminum No. 36

172.0 Jai No. 1

173.0 Tulasi(S)*, Tulsi No. 180

174.0 Ophiopogon jaburan variegata No. 1

175.0 Plumbago capensis No. 1

176.0 Kshria Campa(S)*, Chafa, Champa No. 1

177.0 Champa No. 54

178.0 Shami No. 1

179.0 Pterospermum acerifolium No. 1

180.0 Dadima(S)*, Dalimba No. 1

181.0 Putranjiva, Jivika(S)* No. 1

182.0 Cane Palm No. 54

183.0 Sanseveria trifasciata “Golden Hanii” No. 1

184.0 Sanseveria trifasciata”Laurentii” No. 1

185.0 Asoka, Asok(S)* No. 36

186.0

Providing and fixing rolling shutters of approved make

made of 80MM wide M.S. laths inter-locked together

through their entire length and jointed together at the

ends by end locks mounted on specially designed pipe

shaft with bracket plaes, guide channels and

arrangements for inside and out side locking with push-

pull operation including the cost of hood cover and

spring etc. complete.[A] Shutters having width below

3.5M including cost of Top cover & inside gap

measurement will be applied for quantity

Sq.M. 200

b Shutters having width 3.5M and above. Sq.M. 10

187.0

Providingand applying Bonding Agent apply to the

existing or new surface before plastering to the same

with standard approved bonding agent recommended

by Architect/Structure engineer, apply to the surface as

per Manufacturer's Instruction. Apply Bonding

Chemical in between two layer of cement plaster in

1:3( 1 part chemical: 3 part Cement) and apply with

brush on cleaned and washed surface

Smt 390

188.0Dewatering the excavated areas including pumping

and labour, completehp/hour 970

189.0

Providing and fixing cattle trap, ladder (welded or

bolted) made up of steel section such as flat, bars,

angles, I section, M. S. pipes, etc. as necessary

fixtures, fastenings, holdfasts and applying one coat of

zinc chromate red oxide and two coat of enamle

paint,AS SHOWN IN DRAWING.: T-TYP-CAT-01

Kg 245




190.0

STONE WORK

PARGOLAS(3m span x3part) as per ar.drawing

construction in white lime stone providing and fixing

white lime stone for different type of construction

work like ornamental pillar,sill,pargolas etc. work.with

1:3(1part cement,3part of screen sand)and required

s.s.pins for joinery.adhesive with all required

scaffolding ficher tools and tackles for cutting shape

including groove polishing and all finish as per

drawing.(Khumbhi,Pillar,Bhetasaru,Paat,,Chhatiya,Pid

hiya(pargolas))AS SHOWN IN DRAWING.: T-TYP-

PG-S-01,T-TYP-PG-05

Sq.M 72

191.0

KIRTISTAMBHA as per ar.drawing construction in

white lime stone providing and fixing white lime stone

for different type of construction work like ornamental

plinth 1and2, sill,daso,stone

steps,hathi,lion,pot,karnpith,kumbhi,kalso,kewar,kadav

,moyalapatti,kadav,gokha,murti,chhajika,pushapakanth

,kewal,paal,shikari,zarookhas,theki,bharni,pillar,chhaju

,kathedi,samran,lamsa,kalash,rupkam,floring

etc,work.with 1:3(1part cement,3part of screen

sand)and required s.s.pins for joinery.adhesive with all

required scaffolding ficher tools and tackles for cutting

shape including groove,chainpully crane,polishing and

all finish as per ar.drawing,art & crafts work as per

designe.(sill-1,plinth kadav-1,daso-1,sill-2,plinthkadav-

2,daso-2,stone steps,pot with pedastal,pith-

1,karnpith,kumbhi thar,kalaso thar,dabadi kewal,jangi

thar,chhajika,dodhiyo/puspkanth,bharni/kewal/paal,shi

khari/zarrokho,chhaju,dodhiyo,kewal/daso/peti,theki,z

anzari,pillar,samaran(chhaju,kewar,dodhiyo,lamsa,amb

alsro,kalas),etc.,as shown in drawing.: T-TCM-A1-D-

05

smt 207

bRupkam(haathi,lion,dwarpaal) as shown in drawing.:T-

TCM-A1-D-05smt 18

192.0

Rupkam with pedastal as per ar.drawing construction

in white lime stone providing and fixing white lime

stone for different type of construction work like

karnpith,kumbhi,kewar,daso,different type of artistic

(mundra) murty work work.with 1:3(1part

cement,3part of screen sand)and required s.s.pins for

joinery.adhesive with all required scaffolding ficher

tools and tackles for cutting shape including

groove,chainpullycrane,polishing and all finish as per

drawing,art & crafts work as per designe.(base

stone,karnpith,kumbhi,kewar,daso,murty)AS SHOWN

IN DRAWING.: T-TYP-LKS-S01

smt 4.5




193.0

Renovation of Chhatardi As per drawing construction


stone for different type of construction work Chardham

replika(model work) make in white lime

stone.work.with 1:3(1part cement,3part of screen

sand)and required s.s.pins for joinery.adhesive with all

required scaffolding ficher tools and tackles for cutting

shape including groove,chainpully crane,polishing and

all finish as per ar.drawing,art & crafts work as per

designe.(Chhatardi)

RMT 9

194.0

Rupkam with pedastal As per ar.drawing construction


stone for different type of construction work like

karnpith,kumbhi,kewar,daso,different type of artistic

(mundra) murty work work.with 1:3(1part




groove,chainpully crane,polishing and all finish as per

ar.drawing,art & crafts work as per designe.(Base

stone,karnpith,kumbhi,kewar,daso,Murty)AS SHOWN

IN DRAWING T-TYP-LKS-S01

smt 27

bCharges for Murty rupkam with stone cost.AS

SHOWN IN DRAWING T-TYP-LKS-S01 smt 27

195.0

Stone Grill As per drawing construction in white lime

stone providing and fixing white lime stone for

different type of construction work of artistic stone

grill work with sill,pedstal,etc.work.with 1:3(1part




groove,chainpully crane,polishing and all finish as per

ar.drawing,art & crafts work as per designe.(sill,stone

grill(zali),pedstal etc.) AS SHOWN IN DRAWING.:T-

TYP-SRG-01

smt 36




196.0

ELECTRICAL WORKS / LIGHTING

DISTRIBUTION BOARD Indoor Lighting / Raw

Power Distribution Board Fabricated / ready made,

Double door, Per phase isolation, Lockable, Powder

coated, M.C.B. Incommer ,Vertical series type

Distribution boards, with pre-wired up to the connector

strip and with neutral links per phase and connectors

for each circuits and connector strips per phase for

neutral. The rate should include the supply prewired db

at site store.The distibution board should be sheet steel

clad, wall/ recess mounting, dust and vermin proof

distribution boards constructed from 14 SWG sheet

steel IP 42 construction, finished with rust proof red

oxide coating and two coats of paint with hinged

gasketted door and housing the following complete

with suitably rated PVC insulated copper busbars with

interconnections and neutral bar assembly, earthing

terminals.

Note :The DBs shall be supplied at site to be used

during civil construction activity .It shold be supplied

with proper protection to avoid any physical damage or

NO 2

197.0

Supply, Installation, testing and commissioning of

SPN lighting distribution board indoor as per the IS,

specification and single line diagram.INCOMER 40A

DP ELCB,OUTGOING: 4 NOS 6/10A/16A SP MCB

NO 8

198.0

FEEDER SECTION PILLAR (For External Lighting

& Streetlighting) 'Supply, Installation, Testing and

Commissioning of street lighting Feeder section Pillars

as per details given below. (Double door, Out door

type with IP 65 Protection). (The Section pillar shall be

with 4 nos. alluminum busbars & GI Earth bus)

INCOMER :1 NO. 63 AMP TPN MCB,CT:

75/5A,63A TP CONTACTOR WITH 24 HOUR

TIMER,KWH METER,.OUTGOING:10 NOS. - 25A

TPN MCB WITH TIMER AND ON OFF PUSH

BUTTON,3NOS.- 40A DP ELCB,BUSBAR: 63 AMP

TPN AL busbar.

NOS 3

199.0

Outdoor Power Receptacles 'Supply, Installation,

Testing and Commissioning of Prewired Industrial

type Power socket outlets as per details given below.

(Body made up from Fire resistant thermoplast

material with IP 65 protection class, transparent front

cover for MCB compartment). INCOMER :1 NO. 63

AMP TPN MCB;Outgoing Sockets with MCBs:2

NOS. - 16A SINGLE PHASE,1 NOS. - 16A THREE

PHASE

NOS 4




200.0

INTERNAL LIGHTING & FANS Supply,Installation,

assembling, connection, testing & commissioning of

fixtures complete with suitable rating tubeslamps, high

power factor improving capacitor, HF Electronic

Ballast , Starter and all other necessary accessories to

complete the installations.Note : All light fixture will

have Super low loss Electronics ballast with PF>0.85

& harmonics within permissible limits specified as per

IS, Supply, Installation, testing and

commissioning of 1 X 40 W wall mounted tube light

point with lamp complete. Necessary civil works is

also included in this rate.(Refer cat no.IGP1414EB

Crompton Greves)

NO. 28

201.0


70watt MH Luminire with built in ignitor complete

with lamp. Necessary civil works is also included in

this rate.(Refer cat no.LSA1107IH/MH Crompton

Greves)/equivalent

NO. 28

202.0

Supply, installation, testing and commissioning of

2x18 W CFL surface mounted light fixtures with

suitable rating lamps, low loss electronics ballast, high

power factor improving capacitor etc with all

accessories equivalent to Artlite-RL2815 or RL2819

NO. 4

203.0


13watt BL Luminire complete with lamp. Necessary

civil works is also included in this rate.(Refer cat

no.CBH 13 Crompton Greves/Equivalent)

NO. 11

204.0Supply,Installation, testing & commissioning of

1200mm Dia ceiling fan.NO. 16

205.0Supply, Installation, testing and commissioning of

300mm dia exhaust fan.NO 2

206.0

INTERNAL WIRING Wiring for Light Points

Controlled from Switch Boards Supply, installation,

connection, testing & commissioning of following

outlet points as per Specification & IS. The unit rate

for the point shall consist of the circuit wiring from

LDB or switch board to outlet point through MCB /

switch as required & including the outlet points with

connector & sockets. A point shall include in addition

to phase & neutral wire, earth continuity wire from

LDB to the final termination at outlet points.All the

wiring, outlet points shall be done in a surface /

concealed manner with ISI approved medium duty,

rigid FR PVC, ISI conduit of minimum 25 mm. dia.

using 650 V FRLS copper conductor wire, modular

switches with suitable plate, PVC back box with brass

chromium / cadmium plated machine screws etc.Cost

of MCB shall not be considered in point rate.Wire

Size:Phase & Neutral : 2.5 mm2 Cu FRLS flexible

wire (650 V)Earth : 1.5 mm2 Cu FRLS flexible wire

(650 V),Offwire size = 1.0 sqmm,Average Circuit

Length:,From LDB to Primary SB: 25 MTR.,From

Primary to Secondary SB: 15 MTR.,From SB to

Primary Light Point: 5 MTR..,From Primary to

NO 24

207.0 Secondary light points controlled by one 6A switch NO 65




208.05A socket with one 6A switch on switch board with

cover plate and all required accessoriesNO 14

209.0Ceiling fan point for 1200MM dia fans with Electronic

regulatorNO 16

210.0 Exhaust fan point controlled by one 6A Switch NO 2

211.05A socket with one 6A switch at convinient location

with cover plate and all required accessoriesNO 6

212.0

Wiring for Raw Power Points.Supply, laying,

connection and testing of raw power socket wiring

from PDB to raw power point with following wires to

be laid through electrical channel / floor raceway /

PVC condiut (cost of Channel / raceway / PVC condiut

not to be included in their rate.) Cost of MCB shall not

be considered in point rate.,Wire Size:,Phase &

Neutral : 4.0 mm2 Cu FRLS flexible wire (650

V),Earth : 2.5 mm2 Cu FRLS flexible wire wire (650

V),Average Circuit Length:,Average Circuit

Length:,From PDB to Primary Power Socket : 25

MTR.,From Primary Point to Secondary Power Socket:

7 MTR.. (a)6/16A socket with

one 16A switch

NOS. 10

213.0

Supply, laying, connection and testing of above

mentioined wires from PDB to raw power socket to be

laid through electrical channel / floor raceway / PVC

condiut

MTR. 120

214.0Supply and laying of 25 mm. dia. Rigid PVC medium

duty conduitsMTR. 120

215.0

LT CABLES: Supply, laying, connection, testing and

commissioning of heavy duty medium voltage cables

as per Specification and IS 7098 PART I XLPE

insulated and outer sheeth of FRLS and inner PVC

sheeth stranded AL conductor unless or otherwise

specified. The cable shall be laid underground when

laid outside the building in the method as specified and

shall be laid in prepared trench / cable tray / duct when

laid inside the building. The cable shall be laid to

UPVC pipe at the entry of the building. The unit rate

shall include (a)Delivery of the cables at

site.,(B)Unloading at site store.,(C)Shifting of cable

from site store to place of installation..(D)'Laying of

cable in the prepared trench / cable tray / duct when

laid inside the building or underground when laid

outside the building.,(E)Connection of

cable.,(F)Excavation in hard or soft murrem / rocky

area upto required depth, supply and laying of

protection bricks, supply and backfilling with fine

sand, leveling the ground to match with the existing

condition (G)'Supply and fixing of cable clamps,

brackets, supports, route markers etc as required for

cable tray, duct.(H) Earthing the glands and armouring

MTR. 5

b 3.5C X 70 SQ. MM. AL XLPE Armoured Cable MTR. 50

c 3.5C X 50 SQ. MM. AL XLPE Armoured Cable MTR. 5

d 3.5C X 35 SQ. MM. AL XLPE Armoured Cable MTR. 50

e 4C X 10 SQ. MM. AL XLPE Armoured Cable MTR. 150

f 4C X 4 SQ. MM. CU XLE Armoured Cable MTR. 50

g 3C X 6 SQ. MM. CU XLE Armoured Cable MTR. 350




216.0

CABLE ENDTERMINATIONS 'Supply, fixing,

connection, testing & commissioning of DOUBLE

compression brass cable glands and crimping type

Bimetalic lugs / sockets with necessary tools and

equipments as specified in specifications and IS. The

glands and lugs / sockets shall be suitable for cable

size and type mentioned above. The job also includes,

if necessary, supply and fixing of extension busbar of

same material on circuit breaker or panel board

terminal / connector to connect more than one no. of

parallel cables or to connect higher size cable to lower

size unit. The job also includes earthing the glands and

armour of the cable with common earth bar or flexible

copper mesh.(A)3.5C X 95 SQ. MM. AL XLPE

Armoured Cable

NO. 2

b 3.5C X 70 SQ. MM. AL XLPE Armoured Cable NO. 2

c 3.5C X 50 SQ. MM. AL XLPE Armoured Cable NO. 2

d 3.5C X 35 SQ. MM. AL XLPE Armoured Cable NO. 2

e 4C X 10 SQ. MM. AL XLPE Armoured Cable NO. 6

f 4C X 4 SQ. MM. CU XLE Armoured Cable NO. 2

g 3C X 6 SQ. MM. CU XLE Armoured Cable NO. 14

217.0

EXTERNAL LIGHTING 'Supply,eraction,

assembling, checking and testing of of decorative

external light poles and high mast with fittings and

clamps as specified in Specification. The unit rate

shall also include following :(a)Fixing of pole with

Sintex eq. Junction box (IP 65) of 300x200x105

mm with 8. way connector & 2 Nos. of 6 A DP

MCB, 38. mm. dia., PVC cable entry & exit

conduit as required.(b)Supply and laying of 3 nos.

38 mm. dia.G.I pipe suitable for XLPE cable entry

and exit to junction box as required.(c)Concrete

coping with base plate & necessary civil

works.(d)Earthing and painting..(e)Supply &

connecting of wiring from junction box to the light

fixture, using 3c x 2.5 sq.mm. PVC copper

conductor, flexible cable.(f)Concrete coping with

base plate & necessary civil works(g)Excavation

and back filling.'Supply, installation, testing, and

commissioning of 7.5 mtr ht, swaged pole 410 SP-

5 external FRP light poles with fittings and

clamps, as per specification and IS.

NO. 94

218.0

Supply & Installation of 400W MH (IP 66) flood light

type light fixtures complete with choke, lamp reflector

and other accessories. Light fixture shall be equivalent

to Cat. Ref: NEOS 3/IB/400/1312

NO. 48

219.0

Supply & Installation of 1 X 70 W CDMT tree

uplighter point complete with intergral choke, lamp &

other accessories-including fixing with base

termination of cables,testing & commissioning of the

same. - Lighting Fixture shall be of Equivallent to

Catelogue No: Artlite-RL4006

NO. 20




220.0


60W LED Facade light points with Base support &

mounting accessories equivalent to Philips-

910403346802.

NO. 3

221.0


70W uplighteres for big statues with Base support &

mounting accessories equivalent to Wipro Urbano

Flood Light-UFH50104B.

NO. 5

222.0


60W uplighteres for small statues with Base support &

mounting accessories equivalent to Philips -

911401184880.

NO. 5

223.0

Supply, Installation, testing and commissioning of 4.5

Mtr high decorative pole with base support and

mounting accessories to mount 70W decorative POST

TOP light fixture with lamp complete equivalent to

Artlite-RL4325. Necessary civil works is also

included in this rate.

NO. 13

224.0

Supply, Installation, testing and commissioning of 25

Mtr high highmast pole with base support and

mounting accessories to mount 6 NOS 400W/250W

MH light fixture with lamp, accessories complete.

Necessary civil works is also included in this rate.

NO. 8

225.0

Tubelight for Signanges:Supply,Installation,testing &

commissioning of 1 x36W FTL tube light fitting

complete with integral choke,lamp & other

accessories-including fixing with base termination

of cables,testing & commissioning of the same.

Similar to CGL-IGP1414HSB

NO. 10

226.0

Solar Lights:Supply,Installation,testing &

commissioning of 1 x18W CFL light fixture with

choke, lamp, solar panel, battery, battery charger,

CRCA powder coated lockable housing,

accessories and necessary mounting

arrangement including integral wiring

NO. 20

227.0

CABLING :Supply, laying, testing and connecting of

medium voltage cable for external lighting

(a)4c x 16 sq.mm. AL. XLPE Armoured cable

MTR 2160

b 4C X 10 SQ. MM. AL XLPE Armoured Cable MTR 1730

228.0

CABLE END TERMINATION :'Supply, testing and

connection of cable end termination

4c x 16 sq.mm. AL. XLPE Armoured cable

NO. 18

b 4C X 10 SQ. MM. AL XLPE Armoured Cable NO. 294

229.0

HUME PIPE Supply , Installation of 150 mm

dia. RCC HUME [ NP II ]Pipe with

neccessory fixing accessories for laying of

cables.

MTR. 3000

230.0

EARTHING :Supply, testing and commissioning of

earthing work as per standards.

2.5 mtr. long 8 SWG, G.I. wire coil type earthing

station for external lighting pole and junction box.

NO. 94




231.0

EARTHING 'Supply, installation, connection and

testing of plate type / pipe type earthing station for

various electrical equipments and systems as per

IS with following.(A)Excavation in hard

marrum,(B)'Supply of copper plate electode / G.I.

Pipe electrode.(c)Supply & fixing of watering

pipe.(d)Supply of civil material and preperation of

brick masonry earth pit chamber with C.I. frame

and hinged covers of suitable size as per

drawing.(f)Supply and providing of charcoal and

salt for filling in earth pit.(g)Supply of tools and

tackles necessary for excavation to a desire depth

and doing necessary civil work etc.(h)Testing

earth resistivity before earthing and electrode

resistance after completion of work.(i)Supply and

fixing of Equipotential bar with housing alongwith

necessary mounting accessories.'Supply and

making of maintenance free earthing of 80MM Dia

for body/neutral earthing in corrosive

area.,Conductor: CU,Length : 2000MM (2-Meter)

with necessary back filling Compound,Outer

Electrode Dia : 76MM,Inner Electrode Dia : 38MM

,Terminal Hole Dia : 12MM,Outer Electrode Wall

Thickness : 16swg (1.626mm),Inner Electrode

Wall Thickness : 12swg (2.641mm),Hot dip

Galvanization : Outer Electrode 70-100 micron

NO. 40

232.0

Supply, laying, connection and testing bare earthing

conductor for inter-connecting the earthing stations

and various equipment in built up trenches,

walls/ceiling, buried in ground generally as specified

and shown on the drawing complete with :(a)Supply &

fixing accessories like earthing clamp, saddle,

etc.,(b)Supply of corrosion protection of buried

conductors with bituminous coating(c)'Supply of Test

links (Copper) etc.(d)Supply and fixing of

Equipotential bar.(A)8 SWG. GI wire

MTR. 940

b 25 X 6 SQ MM GI Strip MTR. 140

233.0

Equipotential BarSupply, installation, testing and

commissioning of 50 x 10mm GI Equipotential bar of 500 mm length with suitable. junction box to connect earthing

conductor from building earthing to the equipment. (With six

knock outs for connecting the equipment earthing

NO. 3

234.0

MISCELLANEOUS RCC HUME PIPES;

Providing,Supply,Excavation, Laying, Testing and

commissioning of 300mm Dia RCC(NP2 class) HUME

PIPE with necessary joints/coller etc completed

MTR. 5

235.0

Supply, Laying, Testing and commissioning of

150mm(NP2 class) Dia RCC HUME PIPE with

necessary joints/coller etc completed

MTR. 5

236.0

Supply, Laying, Testing and commissioning of

100mm(Np2 class) Dia RCC HUME PIPEwith

necessary joints/coller etc completed

MTR. 20




237.0

MISCELLANEOUS RCC HUME PIPES;

Providing,Supply,Excavation, Laying, Testing and

commissioning of 300mm Dia RCC(NP2 class) HUME

PIPE with necessary joints/coller etc completed

MTR. 5

b 150 mm dia UPVC Pipe MTR. 5

c 100 mm dia UPVC Pipe MTR. 5

238.0

MAN HOLES Providing 450 mm x 450 mm X 600

mm manhole complete with 9" thick brickwall,

plastering on both sides and providing Precast

R.C.C. cover complete in all respect.

NOS. 100

239.0

Providing 600 mm x 600 mm X 750 mm manhole

complete with 9" thick brickwall, plastering on both

sides and providing Precast R.C.C. cover complete

inall respect.

NOS. 5

240.0



sides and providing Precast R.C.C. cover complete

inall respect.

NOS. 5

241.0



sides and providing Precast R.C.C.cover complete inall

respect.

NOS. 5

242.0MUSIC / PUBLIC ADDRESS SYSTEM Supply and

laying of the 2c X 0.75 sq mm shieded cable.MTR. 150

243.0Supply, laying, testing and commisioning of 20 mm

dia Rigid PVC medium duty conduit.MTR. 150

244.0

Supply, Testing and assembling of the 6 W Ceiling

mount Speaker with all necessary accessories to

complete the job

NOS. 15

245.0

Supply, Testing and assembling of the 15 W 1.5m pole

mounted with IP65 enclosure Speaker with all

necessary accessories to complete the job

NOS. 15

246.0Supply, Installation, Testing and commissioning of the

Volume controller.NOS. 5

247.0

Supply, Installation, Testing and commissioning of

audio system rack for Mixing/Booster Amplifier

240W.

NOS. 1

248.0

Supply, Installation, Testing and commissioning of

audio system rack for Mixing/Booster Amplifier

4800W.

NOS. 1

249.0Supply, Installation, Testing and commissioning of 3

CD Changer Audio System.NOS. 2

250.0Supply, Installation, Testing and commissioning of

Dynamic Hand-Held Microphone.NOS. 4

251.0

Supply and laying of the 2C X 0.75 sq mm shieded,

armoured cable laid through RCC hume pipe/PVC

pipes/channels etc for external area (Rates of RCC

hume pipe/PVC pipes/channels shall not be included)

MTR. 450




252.0

TELEPHONE WIRING

Supply,Installation,connection,testing and

commissioning of telephone wiring system as per

specification. The wiring shall be done through

25mm. Dia PVC conduit with required accessories

and hardware ,telephone cable with 2 pin

telephone socket.Supply & laying of 25 mm dia

rigid PVC medium duty conduit for telephone

wiring.

MTR. 20

253.0Supply,laying and termination of 0.6 mm dia tinned

copper 2 pair unarmoured telephone cable.MTR. 50

254.0Supply,laying and termination of 0.6 mm dia tinned

copper 10 pair armoured telephone cable.MTR. 15

255.0Supply and fixing of 10 pair telephone tag box with

KRONE terminalNOS. 2

256.0Supply and fixing of RJ-11 telephone outlet point

complete with backbox & plate.NOS. 4

257.0Supply ,Installation, connection,testing and

commissioning of EPABX of 4/16 points.NOS. 1

258.0

Supply,laying and termination of 0.6 mm dia tinned

copper 2 pair armoured telephone cable laid through

RCC hume pipe/PVC pipes/channels etc for external

area (Rates of RCC hume pipe/PVC pipes/channels

shall not be included)

MTR. 25

259.0

CCTV SYSTEMSupply, Installation, Testing and

Commssioining of 32 Channel Duplex Color

Digital Video Multiplex Recorder(DVR) with 320

GB HDD.

NO 1

260.0Supply, Installation, Testing and Commssioining of

21" color monitor as per specification.NO 1

261.0

Supply & laying of the RG-59 cable for the CCTV

data system in rigid PVC conduit / or channel or

raceway. (the cost of channel/raceway/PVC conduit

not to be included in the rates)

MTR. 2520

262.0Supply & Laying of 2C X 0.75 sq mm shielded

Multistrain Flexible Copper Conductor Power CableMTR. 2520

263.0Supply, laying, testing and commisioning of 25 mm

dia rigid PVC medium duty conduit.MTR. 30

264.0

Supply, Installation, Testing and Commissioining of

3.8 mm Fixed Dome Camera- High Speed with 470

TV lines battery back-up suitable for indoor,wall or

ceiling mounted type

NOS. 2

265.0

Supply, Installation, Testing and Commissioining of

3.8 mm PTZ Camera- High Speed with 470 TV lines

battery back-up suitable for indoor,wall or ceiling

mounted type

NOS 10

266.0Supply,Installtion,Testing and commissioning of video

signal AmplifierNOS 4




267.0

PLUMBING/SANITARY WORKS: SANITARY

FIXTURES & FITTINGS Providing and fixing wash

down wall mounting EWC-P of approved shade,

conforming to Pattern 2 of IS: 2556 (Part -II), with

SWR Selfit Soil PVC pipe and plug bend as per

specifications; glazed vitreous / Cloured European

Water Closet with Cistern (IS-2326), with grouting the

CI chair in side the floor/wall, rubber gaskets,

connecting PVC 110mm dia soil pipe with PVC

coupling, nuts, mounting cistern on WC., and solid

verity heavy duty plastic seat cover as per IS-2548, of

approved make; cutting and making jari work etc.

complete. EWC-P :Equivalent to CERA CLAIR

WHITE WALL HUNG EXTENDED 'P'

NO.2035,CISTERN : CERA CLAIR WHITE TWIN

FLUSH TYPE(5ltr. flush) NO.2115,SEAT COVER :

CERA CLAIR WHITE SOFT CLOSE TYPE NO.2325

Nos. 17

268.0

Providing & fixing wall Orissapan white W.C PVC

pan connector, having all internal fittings complete

with rubber buffers, C.P. nuts, bolts, etc making holes

in walls floors, & making good. The scope also include

providing & fixing of 15 mm C.P. brass bib cocks of

best quality.ORISSAPAN :- CERA (OR) 530 X 400MM

WHITE NO. 2071,BIB COCK : JAQUAR/ KOHLAR -

CONTINENTAL - 037 - CP

Nos. 4

269.0

Providing & fixing Floor Mounting type white E.W.C -

`P’ or 'S' trap with half and full flush type low level

Cistern of IS: 2556 (Part -II), with trap, approved

make., PVC pan connector, seat & lid (heavy duty)

C.P. brass hinges, including all internal fittings

complete with rubber buffers, C.P. nuts, bolts, etc

making holes in walls floors, & making good. EWC-'P'-

'S' : Cera/Parryware/kohlar/Hindware Makes White

Floor Mounting Water Closet. ,EWC-'P'- 'S' :

Cera/Parryware/kohlar/Hindware Makes White Floor

Mounting Water Closet. ,Seat Cover : Heavy Duty

Cera/Parryware/kohlar/Hindware Makes

Nos. 1

270.0

Providing and fixing White glazed vitreous Wash

Basin Oval Under-Counter, size 550x460 mm dia.,

with supporting M.S. or C.I. Brackets, 1 no, 32 mm CP

Bottle trap with extension piece to wall flange with

rubber adopter for waste connection and waste

coupling.; with rack bolt fittings. OVAL UNDER

COUNTER BASIN: CERA CLAIR WHITE NO.1005

Cera/Parryware/kohlar/Hindware Makes,WASTE

COUPLING : (HALF THREAD)JAQUAR/ kohlar

MAKES,BOTTLE TRAP : (With Internal

Partition)JAQUAR/ kohlar MAKES

Nos. 18




271.0


Basin Round Table Top , size 450 mm dia., with

supporting M.S. or C.I. Brackets, 1 no, 32 mm CP

Bottle trap with extension piece to wall flange with

rubber adopter for waste connection and waste

coupling. comp. etc.ROUND TABLE TOP OVER

COUNTER BASIN: CERA CLAIR WHITE NO.1005

Cera/Parryware/kohlar/Hindware Makes,WASTE

COUPLING : (HALF THREAD)JAQUAR/ kohlar

MAKES,BOTTLE TRAP : (With Internal

Partition)JAQUAR/ kohlar MAKES.

Nos. 2

272.0


Basin Rectangular wall mounting type , size 550 x 450

mm., with supporting M.S. or C.I. Brackets, 1 no, 32

mm CP Bottle trap with extension piece to wall flange

with rubber adopter for waste connection and waste

coupling. comp. etc.RECTANGULAR WALL

MOUNTING BASIN: CERA CLAIR WHITE

NO.1005 Cera/Parryware/kohlar/Hindware

Makes,WASTE COUPLING : (HALF

THREAD)JAQUAR/ kohlar MAKES,BOTTLE TRAP

: (With Internal Partition)JAQUAR/ kohlar MAKES.

Nos. 2

273.0

Providing and fixing central hole basin prassmatic

pillar cock, with required braided pipes from basin

pillar tap to angular stop cock etc

complete.PRASSMATIC PILLAR TAP:JAQUAR/

kohlar MAKES-CONTINENTAL-NO.

Nos. 18

274.0

Providing & fixing of Flush cock with wall Flange

25mm with lever knob complete in all respects

including cutting and making good the walls

etc.FLUSH COCK JAQUAR/ kohlar MAKES-

CONTINENTAL-NO. 1081

Nos. 2

275.0

Providing and fixing high level pneumatic flush tank

15 ltr. with approved shade, conforming to Pattern 2 of

IS: 2326 (Part -II), with PVC Flush pipe , Vent pipe ,

and operating flush knob , with all internal fittings as

per specifications; pipe with PVC coupling, nuts,

mounting cistern above WC., cutting and making jari

work etc. complete. ( For All Type of

EWC)PNEUMATIC FLUSH TANK : COMMANDER

MAKE OR EQUIEVALANT

Nos. 2

276.0

Providing and fixing grab bar fabricated from 32mm

dia seamless stainless steel tube 2mm thick in bath

room with non slip gripping surface, polished wall

flange at end of bars with heavy duty anchor fasteners

& accessories. ( For Hospital building only) GRAB

BAR : JAQUAR - HOTELIER ACC - 1501 - CP

Nos. 3




277.0

Providing & fixing of wall mixer 3 in 1 system with

provision for both telephone shower and overhead

shower complete with bend pipe. ( For Patient

Rooms and All Common area Toilet 1 no bath

provision) MIXER UNIT : JAQUAR/ kohlar MAKES -

Continental - 281,OVERHEAD SHOWER -

Continental -491 JAQUAR/ kohlar

MAKES,TELEPHONE SHOWER-553-Continental-

(With 1.5M. Long Flexible Tube & Swivel Wall

Hook) JAQUAR/ kohlar MAKES

Nos. 2

278.0

Providing & fixing in position best Indian make toilet

recessed type paper holder complete in all respects


etc.TOILET PAPER : JAQUAR/ kohlar MAKES -

ACC - 1553 - CP

Nos. 11

279.0

Providing & fixing in position 15 mm C.P. brass bib

cocks of best quality (as approved by the Engineer-in-

Charge).2-way BIB COCK : JAQUAR/ kohlar

MAKES - Continental -041 - CP

Nos. 11

280.0

Providing & fixing of Jet Spray, with 8mm Dia,1Rmt

Long pvc Tube and accessories to complete the item.

JET SPRAY : 15mm dia. JAQUAR/ kohlar MAKES

Continental CP: NO.069

Nos. 11

281.0

Providing & fixing 15mm C.P. brass angle valve with

C.P. copper connecting pipe 450 mm long and nuts,

washer and brass flange complete, including cutting

and making good the wall where required. ANGLE

VALVE : JAQUAR/ kohlar MAKES -Continental -

053 ,COPPER PIPE : JAQUAR - ALLIED - 805

Nos. 25

282.0

Providing & fixing C.P. brass towel ring fixed to rawl

plug with C.P. brass screws.TOWEL RING :

JAQUAR/ kohlar MAKES - CONTINENTAL - ACC -

1121 - CP

Nos. 7

283.0

Providing & fixing of Tumbler Holder, with all

accessories to complete the item.TUMBLER HOLDER

: JAQUAR/ kohlar MAKES - CONTINENTAL - ACC

- 1141 - CP

Nos. 15

284.0

Fixing stainless steel recessed type soap dish of

approved make. Including providing & fixing screws,

washers, cutting & making good the walls.SOAP DISH

: JAQUAR/ kohlar MAKES - CONTINENTAL - ACC

- 1131 - CP

Nos. 15

285.0Providing & fixing C.P. brass liquid soap container of

best quality.JAQUAR/ kohlar MAKESNos. 2

286.0

Providing & fixing C.P. brass air purifier fixed to

wooden cleats with C.P. brass screws

complete.JAQUAR/ kohlar MAKES

Nos. 2




287.0

Providing & fixing stainless steel sink, R.S. or C.I.

Painted brackets painted, 40mm dia. C.P. waste, C.P.

brass chain and rubber plug, strainer with necessary

C.P. brass unions complete including painting the

fittings and cutting and making good the walls

wherever required, with CP sink cock with raised "J"

shaped swinging spout.NIRALI - GRACE - PLAIN -

510 X 432 MM ,JAQUAR/ kohlar MAKES -

Continental - SINK COCK WITH RAISED "J"

SHAPED SWINGING SPOUT (NO. 347).

Nos. 2

288.0

Providing & fixing Ceramic Lab Sink, R.S. or C.I.

Painted brackets painted, 40mm dia. C.P. waste, C.P.

brass chain and rubber plug, strainer with necessary

C.P. brass unions complete including painting the

fittings and cutting and making good the walls

wherever required, with CP sink cock with raised "J"

shaped swinging

spout.NIRALI/CERA/kohlar/PARRYWARE/HINDW

ARE - WHITE- PLAIN - 510 X 432 MM ,JAQUAR/

kohlar MAKES - Continental - SINK COCK WITH

RAISED "J" SHAPED SWINGING SPOUT (NO.

347).

Nos. 2

289.0

Providing & fixing in position best Indian make C.P.

brass twin way QUOTE and hat hooks fixed into wall

with C.P.brass screws and rawlplugs etc. complete


etc.(Jaquar Cat - CAN - 1161).DOUBLE QUOTE

HOOKS: JAQUAR/ kohlar MAKES-

CONTINENTAL-ACC-1161-CP.

Nos. 43

290.0

Providing & fixing white vitreous china flat back

urinal of size 590x375x390mm as per IS-2556 (Part-2

) with C.I. hangers and 15mm dia. C.P. spreader,32mm

dia CP bottle trap and pipe to wall with C.P. flange

complete including cutting and making good the walls

and floors wherever required. FLAT BACK LARGE

URINAL,WASTE COUPLING (FULL

THREAD)JAQUAR/ kohlar MAKES

Nos. 13

291.0

Supply and fixing Sensotronic Concealed Type Urinal

flush valve with installation box with control valve

Battery / Electric operated automatic flushes of

approved make. System provided with a solenoid valve

and valve connected to a 6 volts lithium battery. Unit

automatically serves (the range in about 40 cms) and

flushes in two steps. The pre flush is for 2 seconds

duration and the final flushing is for 7 seconds

duration. The outlet from the flusher shall be

connected to urinal spreader etc, complete., with

required braided pipes from sensor to spreader.

SENSOR : JAQUAR/ kohlar MAKES

Nos. 13




292.0

Providing & fixing white vitreous china flat back

urinal of size 590x375x390mm as per IS-2556 (Part-2

) with C.I. hangers and 15mm dia. C.P. spreader,32mm

dia CP bottle trap and pipe to wall with C.P. flange

complete including cutting and making good the walls

and floors wherever required.,WASTE COUPLING

(FULL THREAD)JAQUAR/ kohlar

MAKES,PRESSMATIC AUTO ON/OFF ANGULAR

STOP COCK:- JAQUAR/kohlar MAKES

Nos. 2

293.0

Providing & fixing of concealed stop cock with wall

flange and complete., for the following sizes. 15mm

dia. (A)JAQUAR/ kohlar MAKES CONTINENTAL

CP: NO.069

Nos. 2

b20mm dia. JAQUAR/ kohlar MAKES

CONTINENTAL CP: NO.087Nos. 2

294.00

Providing and fixing of electrical instantaneous and

Storage type water Geyser of approved make.(A)5LPM

JAQUAR A-O SMITH JAQUAR/ RECOLD/

SPEARHOT/ kohlar MAKES

Nos. 7

b15LPM JAQUAR A-O SMITH JAQUAR/ RECOLD/

SPEARHOT/ kohlar MAKESNos. 2

c25LPM JAQUAR A-O SMITH JAQUAR/ RECOLD/

SPEARHOT/ kohlar MAKESNos. 2

295.00

Providing & fixing in position 15 mm C.P. brass bib

cocks of best quality (as approved by the Engineer-in-

Charge).BIB COCK : JAQUAR/ kohlar MAKES -

Continental -037 - CP

Nos. 12

296.00

Providing & fixing in position 15 mm C.P. brass

Prassmatics Angular stop cock of best quality (as

approved by the Engineer-in-Charge).PRASS MATIC

ANGULAR STOP COCK : JAQUAR/ kohlar MAKES

- Continental -077 - CP

Nos. 2

297.00 Providimg & fixing of anticocroach trap four Ply. Nos. 43

298.0

INTERNAL DRAINAGE: (SOIL, WASTE, VENT

AND RAIN WATER PIPES & FITTINGS) Providing

fixing, testing and commissioning in position 3

RmtSWR PVC PIPE TYPE-B, self fit pipe

comforming to IS:13592 including all fittings such as

bends, junctions, inspection doors, offests, cowl,

access pieces/plugs etc. jointing with PVC Adhesive

joints including cutting holes in walls and making

good the same. (Inside TOILET) SOIL WATER:-

(A)160 mm dia.(6Kg/Cm2)

Rmt 2

b 110 mm dia..(6Kg/Cm2) Rmt 60

c 75 mm dia. ( Vent Pipe ).(4Kg/Cm2) Rmt 2

299.0

Providing fixing, testing and commissioning in

position 3 RmtSWR PVC PIPE TYPE-B self fit pipe

comforming to IS:13592 including all fittings such as

bends, junctions, inspection doors, offests, cowl,

access pieces/plugs etc. jointing with PVC Adhesive

joints including cutting holes in walls and making

good the same. (INSIDE TOILET )(WASTE

WATER); (A)160 mm dia.

Rmt 2

b 110 mm dia. Rmt 2

c 75 mm dia. Rmt 70




300.0

GI medium ("B" Class)duty waste pipe from wash

basin/ sink to trap with all fittings & shall conform to

IS 1239 (A)Size : 40 mm

Rmt 55

b Size : 32 mm Rmt 2

301.0

Providing & fixing PVC Floor Trap OR multi floor

trap of 75mm dia diameter, with necessary distance

piece of 75mm dia PVC pipe(6kg/cm2) and

150x150mm grating, making necessary SLAB

/WALLholes and cutting walls, etc complete.

(Supreme/ Finolex/ Prince/ Astral Makes) (A)110mm x

75mm

Nos. 60

b 110mm x 50mm Nos. 2

c 110mm x 110mm Nos. 2

302.0

Providing and fixing RIGID PVC Pipe (for rain

water) ISI marked brand as per IS:4985 (6 kg/cm2.)

complete with PVC Fittings & clamps & hinges

including cutting and making good the walls & ceiling

for waste pipes, connections & as directed by the

Engineer-in-Charge.(Supreme/ Finolex/ Prince/ Astral

Makes)RAIN WATER:-(A)160 mm dia.

Rmt 2

b 110 mm dia. Rmt 50

c 75 mm dia. Rmt 2

303.0

COLD / HOT /DRINKING WATER SUPPLY:

INTERNAL WATER SUPPLY WORK:-

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold

water supply including all CPVC plain & brass

threated fittings including fixing the pipe with clamps

at C/C 1.00m spacing. This includes jointing of pipes

& fittings with one step CPVC solvent cemetnt and

testing(Minimum 6 bar pressure required) of joints

complete as per direction of engineeer in charge.

(SUPREME /AASHIRWAD/

ASTRAL/EQUIVALENT) (Internal pipe work : inside

Toilet & OHT to Toilets) HOT WATER PIPES; (A)15

mm dia

Rmt 10

b 20 mm dia Rmt 2

304.0COLD DOMESTIC WATER SUPPLY:-

(A)15 mm diaRmt 50

b 20 mm dia Rmt 50

c 25 mm dia Rmt 115

d 32 mm dia Rmt 40

e 40 mm dia Rmt 2

f 50 mm dia Rmt 2

305.0

Supply, instalation, testing & commissioning of

gunmetal, male or female threaded isolation control

valve (Wheel Valve), confirming to IS 778, PN 1.0,

with necessary specials, union, nipples, insualation,

etc., to complete the job. (For Internal Toilet Work) (

Zoloto/ Audco/ R.B.) (A)15mm dia

Nos. 2

b 20mm dia. Nos. 2

c 25mm dia. Nos. 12

d 32mm dia. Nos. 2

e 40mm dia. Nos. 2

f 50mm dia. Nos. 2




306.0

Supply, instalation, testing & commissioning of

gunmetal, male or female threaded isolation control

valve (Ball Valve), confirming to latest IS , PN 1.0,

with necessary specials, union, nipples etc., to

complete the job. (For Terrace Ring ) ( Zoloto/ Audco/

R.B.) (A)15mm dia

Nos. 2

b 20mm dia. Nos. 2

c 25mm dia. Nos. 2

d 32mm dia. Nos. 2

e 40mm dia. Nos. 2

f 50mm dia. Nos. 2

307.0

Supply, Installation, Testing and Commissioning of 25

mm dia. air release valve. ( Zoloto/ Audco/ R.B./

Spirex)

Nos. 2

308.0

Providing and fixing float valve with pressure type

(PVC) float of approved make.( Zoloto/ Audco/ R.B./

Spirex) (A)20 mm dia.

Nos. 2

b 25mm dia. Nos. 2

c 32mm dia. Nos. 2

d 40mm dia. Nos. 4

309.0Providing & Fixing of water cooler with all accessories

(Voltas / Blue Star / equivalent) Capacity : 500 ltr.Nos. 2

310.0

Providing & Fixing of domestic R.O. plant with

storage tank & piping with all accessories (Ion

Excahnge / Power H2O / Equivalent, Capacity :

500 ltr./hr.

Nos. 2

311.0

EXTERNAL DRAINAGE & WATER SUPPLY

WORKEXTERNAL DRAINAGE (SOIL / WASTE)

Excavation in all type of soil, soft or hard murrum in

line level and plumb as per cross section of trench with

dressing sides and ramming botom of trench, including

refilling trenches, watering, compacting , removing &

transporting surplus stuff within site or out side the

premises as per the site Engineer instruction(A) up to

1.5 mtr.depth (0.75 mtr wide)

Cu.M 2

b from 1.5 mtr to 3 mtr depth (1.25 mtr wide) Cu.M 125

c from 3 mtr to 4.5 mtr depth Cu.M 2

d from 1.5 mtr to 3 mtr depth (1.25 mtr wide) Cu.M 125

e from 1.5 mtr to 3 mtr depth (1.25 mtr wide) Cu.M 125

312.0

Providing,Llaying, Jointing with stiff mixture of C-M-

1:1, salt glazed 'A' class stoneware pipe including

testing of joints, commissioning etc comlete

A-150 mm dia

Mtr. 2

b 230 mm dia Mtr. 100

c 300 mm dia Mtr. 2

d 450 mm dia Mtr. 2

313.0

Providing, mixing and laying of P.C.C. M10 in the

pipe line for trench for pipe support and encassing it

as per detail of structural engineer recommendation for

C.C ratio and Steel if require, including ramming,

watering, curing etc complete.

A-150 mm dia (450 mm wide) (116mm Average

Depth)

Mtr. 2

b 230 mm dia (550 mm wide) (116mm Average Depth) Mtr. 150

c 300 mm dia (600 mm wide) (125mm Average Depth) Mtr. 2




314.0

Providng and constructing gulley trap chamber in brick

masonary with C.I. gratings and water type C.I. frame

and cover of 300mm x 300mm size. The weight of C.I

cover with frame should not be less than 4.5 kg.

A-100mm x 100 mm P -Type

Nos. 2

b 150mm x 100 mm P-Type Nos. 6

315.0

Constructing water tight brick masonry grease trap

with second class bricks in cement mortar 1:4 (1

cement :4 coarse sand), R.C.C. top slab with 1:2:4 mix

(1 cement :2 coarse sand :4 graded stone aggregate

20 mm nominal size, foundation concrete 150 mm

thick 1:4:8 (1 cement :4 coarse sand :8 graded stone

aggregate 40 mm nominal size), inside plastering 12

mm thick with cement mortar 1:3 (1 cement :3 coarse

sand) finished with a floating coat of neat cement

& FRP. foot rests including fixing in 20 x 20 x 10 cm

cement concrete blocks 1:3:6 (1 cement :3 coarse sand

:6 graded stone aggregate 20 mm nominal size), two

brick masonry baffle walls each of 500 mm depth &

third one 600 mm deep each of 115 mm thickness, 1

No. cast iron double seal manhole cover with frame

(internal size 455 x 610 mm & total weight of cover

& frame to be not less than 38 kgs) & 2 Nos C.I.

double seal medium duty covers each of 450 x 450

mm size including excavation, backfilling & disposal

of surplus earth complete as per standard

design.(Note : Cost shall include dewatering & water

Nos. 2

316.0

Providing and Laying non pressure NP2 class (Light

duty) RCC hume pipe with coller joints in C.M.(1:2) as

sleeve pipe including watering, testing etc complete A-

150 mm dia

Mtr. 2

b 250 mm dia Mtr. 2

c 300 mm dia Mtr. 2

317.0

Constructing brick masonary chamber for under

ground C.I. inspection chamber and bends with bricks

having crusing strength not less than 35Kg./Cm2 in

Cement Mortar 1:5 C.I. cover with frame (Light dury)

450MM 8 610Mm internal dimension etc. complete.

[I] Inside dimensions, 455MM *610MM and 450MM

deep for single pipe line.

Nos. 4

318.0

Constructing manhole with R.C.C. top slab in 1:2:4

mix (1-Cement: 2-Coarse sand: 4-Graded stone

aggregrate 20MM nominal size) foundation concrete

1:3:6 mix (1-Cement: 3-Coarse sand: 6-Brick bats 40

to 50mm size) (I) inside size 900MM * 1200MM and

1.5M depth [A] With 230MM thick walls of brick

masonary in Cement Mortar 1:5 (1-Cement: 5-Coarse

sand)(a) Do 900mm x800mm up to 1.5 mtr depth [II] B

type depth 1.50M for 150MM diameter sewer.

Nos. 12

bDo -----900mm x 1200mm from 1.5 mtr to 3 mtr depth

[III] C type depth 2.25M for 150MM diameter sewer.Nos. 2




319.0

Providing and erecting at the site of work steel

ventilating column of 150MM internal diameter and

12.20MM High from G.L. to bottom of top grill,

including C.I. Grill and base plate, bolts and nuts etc.

and excavation in foundation of size 120Cm x 120Cm

x 165CM and filling the pit with first layer of cement

concrete 1:3:6 Mix (1-Cement: 3-Coarsesand: 6-

Graded stone aggregate 20MM nominal size) of

120Cm x 120Cm x 90Cm. and remainning pit with

B.B.C. 1:3:6 Mix (1-Cement: 3-Coarse sand: 6-Brick

bats 40 to 50MM size) and providing fillet in Cement

concrete 1:2:4 Mix (1-Cement: 2-Coarse sand: 4-

Graded stone aggregate 3-coats of silver paint etc.

complete.

Nos. 2

320.0

Construction of septic tank in stone masonary in CM

1:6 including inside water proof plaster, 80 mm thick

water proof IPS in required slope with Vata and RCC

slab on top as per structural design, with manhole

cover (pre cast RCC-medium duty), vent pipe, etc.Size

: 6 mtr x 2 mtr. x 1.4 mtr. liquid depth

Job 2

321.0

Providing sock pit of 5.00Cu.M. volume including

excavating and filing brick bats with dry masonary

work at top for 45Cm. Height including covering the

top with stone including providing vata in Cement etc.

complete as directed.

Job 2

322.0

EXTERNAL DOMESTIC WATER SUPPLY WORK

Providing and fixing ASTM Solvent weld UPVC SCH-

80 pipe, having thermal stability for cold water

supply including all UPVC plain & brass threated

fittings including fixing the pipe with clamps at

1.00m spacing .Including trenching and refilling,

bedding. At bottom of basement beam, (A)20mm

dia. nominal bore

Mtr. 2

b 25mm dia. nominal bore Mtr. 2

c 32mm dia. nominal bore Mtr. 2

d 40mm dia. nominal bore Mtr. 50

323.0

EXTERNAL WATER CONTROL VALVE:-Supply,

instalation ,testing & commissioning of gunmetal, male

or female threaded isolation control valve (Wheel

Valve), confirming to IS 778, PN 1.0, with necessary

specials, union, nipples etc., to complete the job.(A)20

mm nominal bore

Nos. 2

b 25 mm nominal bore. Nos. 2

c 32 mm nominal bore Nos. 2

d 40 mm nominal bore Nos. 4

e 50 mm nominal bore Nos. 2




324.0

( Valve Chamber)Constructing brick masonary

chmaber for under ground , inspection chmaber and

bends with bricks having crushing and bends with

bricks having crushing strength not less than

35Kg.Cm2 in cement Mortar 1:5 C.I. cover with frame

(Light dury) 450MM x 610MM internal dimensions,

total weigh of cover with frame to be not less than

38Kgs. (weight of cover 23Kgs. and wt. of frame

15Kgs.) R.C.C. top slab with 1:2:4 mix (1-Cemetn: 2-

Coarse sand: 4-Graded stone aggregate 20MM size)

foundation concrete 1:5:10 inside water proof plaster

15MM thick with Cement Mortart 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc.complete.

Nos. 4

325.0

STORAGE TANKS Construction of u.g water storage

tank including excavation, foundation concrete, RCC

walls and top & bottom slab including shuttering, steel

work, water proof plaster from both side providing

manhole cover, air cowel etc as per drawing. All RCC

wall shall be executed strictly as per Structural

consultants drawing and specifications.(A)Capacity :

50,000 Ltr

Job 2

b Capacity : 20,000 Ltr Job 2

c Capacity : 10,000 Ltr Job 2

326.0

Supplying, installing, testing & commissioning of

`HDPE’ double layer water storage tank including

holes for inlet, outlet, overflow, level indicator, drain

& vent points, manhole cover, suitable steel supporting

structure complete.( Sintex/Reno/Or Equivalent)

a). 500 ltr.

Job 2

b 1000 ltr. Job 2

c 1500 ltr. Job 2

d 2000 ltr. Job 2

e 5000 ltr. Job 4

327.0

Supply & intsllation, testing & commissioning of Solar

hot water system with solar panels, storage tank,

piping, valves, insualtaion, for complete installation

(A)Capacity : 500 Ltr.

Job 1

a Capacity : 300 Ltr. Job 2

328.0

Supply, installation, testing & commissioning of

centrifugal monoset submersible pump with CI casing

& SS impeller. The pump shall have uPVC sch 80

delivery pipe with PVC isolation valve & NRV on

delivery side. (A)Capacity : 5 mtr3/hr., 10 mtr. head

Nos. 4

b Capacity : 5 mtr3/hr., 15 mtr.head Nos. 2

c Capacity : 10 mtr3/hr., 15 mtr.head Nos. 2

d Capacity : 10 mtr3/hr., 10 mtr.head Nos. 2

329.0


centrifugal monoset submersible recirculation pump

with CI casing & SS impeller. The pump shall have

uPVC sch 80 delivery pipe with PVC isolation valve &

NRV on delivery side. (for Fountain )(A) Capacity :

2.5 mtr3/hr., 20 mtr Head.

Nos. 2

330.0

Supply,minstallation, testing & commissioning of 100

mm dial pressure guages with isolation cock & syphon

tube, etc. complete (A)Range : 0 - 5 kg/cm2

Nos. 1




b Range : 0 - 10 kg/cm2 Nos. 4

331.0

Development & Construction of Tube/Bore well with

required drilling including all material like housing &

casing pipe, strainer with all civil work, testing &

commissioning of the well. The depth shall be upto 40

mtr. The scope shall also include all the tests to be

carried out for the development of the borewell. Size

and depth tentative and shall have to be conformed

after gating advise from Geo-Hydrologist.

Job 2

332.0


Borewell submersible pump with PVC heavy duty

column pipe , CI casing, SS impeller & with required

all fittings, accessories, clamps, starter, etc. complete

Bore Well Size:- 150mm- Tentative

Job 1

333.0

Supply, laying, testing & commissioning of GI Heavy

duty threaded pipes conforming to IS 1239 with all

fittings, couplings, companion flanges (for valves) ,

etc. complete Size : (A)50 mm

Mtr. 50

b Size : 80 mm Mtr. 2

334.0

Valves for Bore Pumps Supply, installation, testing &

commissioning of Short body non rising sluice valve

conforming to IS 14846 PN 1.0 with SS seatings &

with flanges & CS hardwares Size : 50 mm

Nos. 1

335.0

Supply, installation, testing & commissioning of swing

type single door non return valve, with CI body, CS /

CI door, SS hinge pin conforming to IS 5312 PN 1.0

with flanges & CS hardwares Size : 50 mm

Nos. 1

336.0

EXTERNAL STORM WATER DISPOSAL SYSTEM

Storm water channel in stone massonery with C-M- 1:6

including Excavation, Foundation concrete, Inside

water proof plaster, Bottom with 50 mm thick

water proof IPS with necessary vata, cocered with

precast concrete slab etc. a). 300 mm wide and

up to 0.60 . mtr depth

Mtr 2

b 450 mm wide and up to 1 . mtr depth Mtr 2

c 600 mm wide and up to 1.5 mtr. depth Mtr 2

337.0

Constructing Brick masonary road gully chamber

500MM x 450MM x 600MM including 500MM x

450MM C.I. Horizontal grating with frame complete.

No. 2

338.0

Constructing brick masonary road gully chamber

1100MM x 775MM including 500MM x 450MM (C.I.

Horizintal grating with frame and vertical gratting

complete).

No. 2

339.0

Construction of Percolation Well with all required

connections as per detailed design and drawing.

Size : 3 mtr. dia x 4 mtr. depeth (150 mm size casing

pipe up to permeable layer) Note:- Configuration shall

be provided by the contractor accoding to the bore hole

data

No. 6


Unit: Qty Rate Amount 1.0 Excavation for foundation up to 1.5M ...

Documents

Transcript of Unit: Qty Rate Amount 1.0 Excavation for foundation up to 1.5M ...