USER'S MANUAL

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

USER'S MANUAL

2 3 4

1.3 Remove screws as shown to access the motherboard tray.

1.5 If your motherboard included an I/O shield, then replace the X-QPACK2 I/O shield with it. Remove shield by pushing it inward from the position shown.

1.6 Place motherboard on the tray standoffs and screw into place.

1.4 Slide the motherboard tray out of the case.

1.7 Remove covers of expansion slots that you need and install any expansion cards that you have.

1.15 Place 5 1/4" drive(s) into the drive bay.

1.14 Remove 5 1/4" drive bay cover(s) by pushing it out from behind.

1.13 Place a screwdriver in the hole and lift metal plate. Then wiggle plate up/down until it comes loose.

1.12 Secure hard drive by fasten- ing screws on both sides of the cage.

1.11 Slide hard drive into cage.

1.10 Slide cage upward to remove.

1.8 Replace the motherboard tray into the chassis.

1.9 Remove screws to release the hard drive cage.

1.17 Replace the hard drive cage and fasten screws.

All screws for M/B, DVD, HDD are provided inside of the chassis.

Finished appearance.

1 5 6 7

1. Install motherboard, 3 1/2", and 5 1/4" drives:

8

1.1 Remove thumbscrews from the rear of the X-QPACK2.

1.2 Remove the 3-sided panel by sliding it back then lifting upward.

4. Install Hard Drive and CPU temperature sensors:

3. Install front panel leads and LEDs:

5. USB/1394(Firewire)/Audio cable pin assignment:

9

CONTENTS

1. Install motherboard, 3 1/2", and 5 1/4" drives........1

2. Identify the power supply connectors.....................6

3. Install front panel leads and LEDs.........................7

4. Install Hard Drive and CPU temperature sensors.....7

5. USB/1394(Firewire)/Audio cable pin assignment......8

2.4 Serial ATA (SATA) connector x 2. These provide power to your SATA devices.

2.3 4pin peripheral connector x 6. These provide power for IDE devices (HD, CD/DVD) and case fans.

1.16 Secure 5 1/4" drive by fastening screws on both sides of the drive bay.

2. Identify the power supply connectors:

2.5 6pin PCI Express connector x 1. This connector provides power to your PCI Express devices.

2.6 Floppy drive connector x 2. Use to power 3 1/2" floppy drives.

3.1 Locate the USB/Audio/1394 (Firewire) front panel connect- ors. Refer to your mother- boards manual for the proper pin assignment. Generally there is a small triangle on the conn- ectors to indicate the positive line.

'

4.1 Locate HD/CPU senors.

4.3 Tape sensor to the CPU heatsink to monitor CPU temperature.

6. Complete the Installation.....................................9

6. Complete the Installation:

2.2 ATX 12V P4 connector x 1. Supplies power to the CPU via the motherboard.

(see your motherboards manual for location of USB/Firewire headers.)

'

2.1 20/24 pin ATX connector x 1. Four pins can be detached by gently pulling them if you need 20pin.

Note: You may also leave the sensor loose in the chassis in order to monitor overall system temperature. DO NOT place the sensor directly on the CPU as it may cause system damage.

4.2 Tape sensor to hard drive to monitor its temperature.

3.2 Locate the Power LED, HDD LED, Power SW, Reset SW and Speaker front panel leads. Again, please refer to your motherboards' manual for the proper pin assignment.

6.1 Once all components have been installed properly, gently return the 3-sided panel to its initial position (lower the panel over the chassis and push forward). Congratulations, you have completed the assembly of your X-QPACK2.

Cable Cable Color Function

RED +5V

WHITE -D

GREEN +D

BLACK GND

WHITE VP

BLACK VG

RED TPB-

GREEN TPB+

BROWN TPA-

BLUE TPA+

RED MIC-IN

BLACK GND

WHITE MIC-POWER

GREEN LINE OUT FR

BROWN LINE OUT RR

YELLOW LINE OUT FL

BLUE LINE OUT RL

USB 2.0

1394

AUDIO

X-QPACK2 AddendumSystem Guidelines:

1. Your CPU cooler should not exceed 76mm in height.

2. The X-QPack2 can accommodate graphics cards up to 267mm in

length.

3. The power supply's dimensions are:138mm x 148mm x 84mm

and can be replaced with most standard ATX form factor

power supply's.

Changing the LCD display mode:

Our LCD temperature displays use Celsius as the default setting,

as is used on Intel/AMI motherboards. If you would prefer to

display system temperatures in Fahrenheit, you must set the LCD

switch to the "F" position. The switch is located on the PC board

at the rear of the LCD.

Removing the front panel:

With the 3-sided panel removed, locate the two screws on the

inside of the front panel and remove. Next, locate the four clasps

in the front panel. Unhook each of the four clasps and remove

panel. Use caution when handling panel wires.