UCM - Wheel Chocks
2
Page 1 of 2 UCM Wheel Chocks The UCM Wheel Chocks are offered to enhance stability of wheeled plant in operation and for maintenance. Many health and safety professionals and organisations are now specifying the use of chocks to enhance operational safety. The ADR* requirement at 8.1.5 (a) is “for each vehicle (of a transport unit), at least one chock of a size suitable to the weight of the vehicle and to the diameter of the wheels. *ADR is the term used to describe the "European Agreement Concerning the International Carriage of Dangerous Goods by Road. Our thermoplastic plastic chocks are manufactured in the EU and comply with the DIN 76051 regulation (Chocks For Motor Vehicles Semi Trailers and Towings – Nov 1992) to satisfy ADR and other requirements. Test information available on request. We also stock chock holders for both models which can be attached to the vehicle or a wall for storage when not in use. Chock Type C1: • Small yellow plastic wheel chock compliant with EC regulation DIN76051 • For use on small / medium size vehicles • Strong lightweight product for commercial vehicles • Convenient integral carry handle • High quality European polypropylene manufacture • Galvanized steel ant-slip strip to rear of base • L390 x B160 x H200 • Weight 1.5 kg Chock Type C2: • Large yellow plastic wheel chock compliant with EC regulation DIN76051 • For use on large vehicles / HGV’s • Suitable for up to 6500 kg of wheel load (50% of 13000 kg two wheel axle load) • Strong lightweight product for commercial vehicles • Convenient integral carry handle • High quality European polypropylene manufacture • Galvanized steel ant-slip strip to rear of base • Maximum Wheel Radius 530mm • L500 x B200 x H235 • Weight 2.2 kg UCM Wheel Chocks - available from Universal Crane Mats Ltd www.universal-crane-mats.com Contact Mike Allanson on 07581 144466 or email [email protected] for advice on your requirements UCM-WC-Dec2011
Transcript of UCM - Wheel Chocks
Page 1 of 2
UCM Wheel Chocks The UCM Wheel Chocks are offered to enhance stability of wheeled plant in operation and for maintenance. Many health and safety professionals and organisations are now specifying the use of chocks to enhance operational safety. The ADR* requirement at 8.1.5 (a) is “for each vehicle (of a transport unit), at least one chock of a size suitable to the weight of the vehicle and to the diameter of the wheels.
*ADR is the term used to describe the "European Agreement Concerning the International Carriage of Dangerous Goods by Road.
Our thermoplastic plastic chocks are manufactured in the EU and comply with the DIN 76051 regulation (Chocks For Motor Vehicles Semi Trailers and Towings – Nov 1992) to satisfy ADR and other requirements. Test information available on request.
We also stock chock holders for both models which can be attached to the vehicle or a wall for storage when not in use.
Chock Type C1:
• Small yellow plastic wheel chock compliant with EC regulation DIN76051
• For use on small / medium size vehicles
• Strong lightweight product for commercial vehicles
• Convenient integral carry handle
• High quality European polypropylene manufacture
• Galvanized steel ant-slip strip to rear of base
• L390 x B160 x H200
• Weight 1.5 kg
Chock Type C2:
• Large yellow plastic wheel chock compliant with EC regulation DIN76051
• For use on large vehicles / HGV’s
• Suitable for up to 6500 kg of wheel load (50% of 13000 kg two wheel axle load)
• Strong lightweight product for commercial vehicles
• Convenient integral carry handle
• High quality European polypropylene manufacture
• Galvanized steel ant-slip strip to rear of base
• Maximum Wheel Radius 530mm
• L500 x B200 x H235
• Weight 2.2 kg
UCM Wheel Chocks - available from Universal Crane Mats Ltd www.universal-crane-mats.com
Contact Mike Allanson on 07581 144466 or email [email protected] for advice on your requirements
UCM-WC-Dec2011
Page 2 of 2
Chock Size Comparison C1 against C2;
Wheel Chock Brackets
• High quality European polypropylene manufacture
• Available in two sizes to fit Chock Types C1 and C2
• Retainer arm secured by galvanized steel pin for carriage security
• 4 No. 12mm fixing holes to enable secure bolting to vehicle chassis or wall for storage
• Bracket to fit Chock Type C1 weight 0.4 kg
• Bracket to fit Chock Type C2 weight 0.7 kg
UCM Wheel Chocks - available from Universal Crane Mats Ltd www.universal-crane-mats.com
Contact Mike Allanson on 07581 144466 or email [email protected] for advice on your requirements
UCM-WC-Dec2011
