UCF 213 Square flanged ball bearing units
Transcript of UCF 213 Square flanged ball bearing units
UCF 213 Square flanged ballbearing unitsSquare flanged ball bearing units
Technical specification
JIS Compliance with standard
For material handlingapplications
Purposespecific
Cast iron Housing material
Standard seals withadditional flingers
Sealingsolution
2 350 r/min Limiting speed
DIMENSIONS
d 65 mm Bore diameter
d1≈82.1mm
Outer diameterinner ring
A 50 mm Overall width
A1 22 mm Flange width
A5 39 mm Standout of end cover
B 65.1 mm
Overall bearing width
B4 12 mm Distance from locking device side face tothread centre
Db1 155 mm
Top external diameter
J 149 Distance between attachment bolts
Generated from www.skf.com on 2021-09-03
Page 1 of 5
mm
L 187 mm
Overall length
N 19 mm Diameter of attachment bolt hole
s1 39.7 mm
Distance from locking device side face toraceway centre
T 69.7 mm
Overall unit width
GREASE FITTING
DN 6.589 mm Diameter of head sphere of grease fitting
SWN 11.11 mm Hexagonal key size for the grease fitting
GN1/8-27 NPT Thread of the grease fitting
THREADED HOLE
RG1/8-27 NPT Housing thread for grease fitting
R1 34.5 mm Axial position of the housing thread
CALCULATION DATA
C 57.2 kN Basic dynamic load rating
C0 40 kN Basic static load rating
Pu 1.7 kN Fatigue load limit
with shaft tolerance h6
MASS
5.35 kg Mass bearing unit
MOUNTING INFORMATION
G2 M10x1.25 Set screw
5.08 mm Hexagonal key size for set screw
Generated from www.skf.com on 2021-09-03
Page 2 of 5
16.5 N·m Recommended tightening torque for set screw
G 16 mm Recommended diameter for attachment bolts, mm
G 0.625 in Recommended diameter for attachment bolts, inch
INCLUDED PRODUCTS
F 213/Y Housing
UC 213 Bearing
ASSOCIATED PRODUCTS
ECY 213 End cover
Generated from www.skf.com on 2021-09-03
Page 3 of 5
More information
Product details
Flanged units to ISOstandards
Flanged units to NorthAmerican standards
Flanged units to JapaneseIndustrial Standards (JIS)
Flanged units, notstandardized (SKF FoodLine)
Permissible misalignment
Locating/non-locatingsupport flanged
Loads
Temperature limits
Permissible speed
Lubrication
Mounting and dismounting
Ordering information
Designation system
Engineering information
Principles of ball bearingunits selection andapplication - Downloadcatalogue (4.9 MB)Principles of selectingmounted bearing solutions
Bearing failure and how toprevent it
Tools
Bearing Select
Engineering Calculator
Rolling bearings mountingand dismountinginstructions
Generated from www.skf.com on 2021-09-03
Page 4 of 5
Terms and conditionsBy accessing and using this website / app owned and published by AB SKF (publ.) (556007-3495 ·Gothenburg) (“SKF”), you agree to the following terms and conditions:
Warranty Disclaimer and Limitation of LiabilityAlthough every care has been taken to assure the accuracy of the information on this website / app, SKF provides thisinformation "AS IS" and DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. You acknowledge that youruse of this website / app is at your sole risk, that you assume full responsibility for all costs associated with use of thiswebsite / app, and that SKF shall not be liable for any direct, incidental, consequential, or indirect damages of any kindarising out of your access to, or use of the information or software made available on this website / app. Any warrantiesand representations in this website / app for SKF products or services that you purchase or use will be subject to theagreed upon terms and conditions in the contract for such product or service. Further, for non-SKF websites / apps thatare referenced in our website / app or where a hyperlink appears, SKF makes no warranties concerning the accuracy orreliability of the information in these websites / apps and assumes no responsibility for material created or published bythird parties contained therein. In addition, SKF does not warrant that this website / app or these other linked websites /apps are free from viruses or other harmful elements.
CopyrightCopyright in this website / app copyright of the information and software made available on this website / app rest withSKF or its licensors. All rights are reserved. All licensed material will reference the licensor that has granted SKF the rightto use the material. The information and software made available on this website / app may not be reproduced,duplicated, copied, transferred, distributed, stored, modified, downloaded or otherwise exploited for any commercial usewithout the prior written approval of SKF. However, it may be reproduced, stored and downloaded for use by individualswithout prior written approval of SKF. Under no circumstances may this information or software be supplied to thirdparties.This website /app includes certain images used under license from Shutterstock, Inc.
Trademarks and PatentsAll trademarks, brand names, and corporate logos displayed on the website / app are the property of SKF or its licensors,and may not be used in any way without prior written approval by SKF. All licensed trademarks published on this website/ app reference the licensor that has granted SKF the right to use the trademark. Access to this website / app does notgrant to the user any license under any patents owned by or licensed to SKF.
ChangesSKF reserves the right to make changes or additions to this website / app at any time.
Generated from www.skf.com on 2021-09-03
Page 5 of 5