GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Typical Radial Board & Batten Details

BB01

0418-Feb-17

75mm Nominal

100mm Nominal

125mm Nominal

2525

25

50mm Nominal

23

35mm Nominal

65mm Nominal

80mm Nominal

105mm Nominal

Typical Rough SawnUnseasoned Bevelled Edge (BE)

Section Profile

Nom

inal

Nom

inal

Nom

inal

75x25mm BE

100x25mm BE

125x25mm BE

50x25mm BE

Nom

inal

80 50 80

55 100 55

100 50 100

75 100 75

80 75 80

55 125 55

2525

2525

2525

25 25

25 25

25 25

Stainless steel screw as appropriate or Hot DippedGalvanized ring shank nail as appropriate(See Radial Timber fixing recommendations).

Stainless steel screw as appropriate or Hot DippedGalvanized ring shank nail as appropriate(See Radial Timber fixing recommendations).

Stainless steel screw as appropriate or Hot DippedGalvanized ring shank nail as appropriate(See Radial Timber fixing recommendations).

Under lapped board

Over lapped board

Under lapped board

Over lapped board

Under lapped board

Over lapped board

Internal side

Internal side

Internal side

Typical Radial BE Board & Batten combinations:75mm (Face board) x 100mm (Backing board)

Typical Radial BE Board & Batten combinations:100mm (Face board) x 100mm (Backing board)

Typical Radial BE Board & Batten combinations:75mm (Face board) x 125mm (Backing board)

Note: Radial recommends a minimum of 25-30mm overlap of face boards(See Radial Timber fixing recommendation sheet)All Bevelled Edge rough sawn timbers are nominal size.

External Face

External Face

External Face

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

IMPORTANT:Refer to Radial Timber Product specifications for further fixing information:www.radialtimbers.com.au

Typical Radial Bevelled Edge Board & Batten unseasoned rough sawn wall cladding with window/window flashing example inset

GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Radial Board & Batten Wall (Noggin) Fixing Details

BB02

0418-Feb-17

150

Timber framing as perAS1684

Stagger cutting joins over alternating noggins.End cuts to be mitred and flush joined. Cuts to besealed with relevant sealer product as appropriate

Moisture Vapour barrier or relevantimpermeable wall underlay as perNCC and AS1684

Vertical Bevelled Edge Board & Batten boardsfixed to noggins and top/bottom plate. Nogginsmax 600mm centres.

Typical polyethelene film moisture barrier(See AS2870 for further details)

Under lapped Board (See BB01)Over lapped board (See BB01)

End cuts to be sealed with relevant oilbased sealer product as appropriate

Noggins to comply with AS1684.2 (6.2.1.5).Vertical installation is recommended to havefixings at 450 - 600mm maximum.

150mm Min distance as per(NCC: 3.1.2.3) and/or (AS2870: 5.2.2)

BB02:A1

BB02:A2

Steel flashing as per (NCC:3.5.3.6)as appropriate

Fixing as appropriate(See NCC Vol 1: 3.5.3.2 TimberCladding) and Radial Timber fixingrecommendations(www.radialtimbers.com.au)

See Radial fixing recommendations forminimum overlap for Board & Batten.

Typical timber bearer

Termite cap as perNCC 3.1.3 Termite Management &AS3600 Termite Management

Typical Timber Barge Boardsattached to cleat on side of stump

Typical timber joist

Typical Concreteor timber stump

Typical timber frame stud

Typical Particleboardsheeting

Moisture vapourbarrier or releventimpermeable wall

underlay as per NCC

Under lapped board (See BB01)Over lapped board (See BB01)

End cuts to be sealed with relevantoil based sealer product asappropriate.Bottom side of board to be undercutmin 150 angle to form drip edge onvertical fixed boards.Cladding to be min 50mm past FloorLevel

Refer AS1684 Timber FramingManual for Span tables/sizes of

timber subfloor bearers/joists

Width

Over

all D

epth

Depth

Foo

ting

Fill

Min H

eight

Timber framing as perAS1684

Moisture Vapour barrier or relevantimpermeable wall underlay as perNCC and AS1684

Typical Particleboard sheetinglaid over timber floor Joists

(See AS1860.2)

Typical timber bearer

Min sub floor height as perNCC 3.4.1 Sub Floor Ventillation.Height taken from bottom of bearer

to Ground Level (GL)

Typical timber floor joist

Stump & Footing size refer to:AS1684 Timber Framing Manual &/or

AS2870 Residential Slabs & Footings(or Engineers specifications where applicable)

Termite cap on top of stump as perNCC 3.1.3 Termite Management &AS3600 Termite Management

Typical Timber Barge Boardsattached to cleat on side of stump

Typical concrete stump

Stagger cutting joins over alternating noggins.End cuts to be mitred and flush joined. Cuts to besealed with relevant sealer product as appropriate

Vertical Bevelled Edge Board & Batten boardsfixed to noggins and top/bottom plate. Nogginsmax 600mm centres.

Under lapped Board (See BB01)Over lapped board (See BB01)

End cuts to be sealed with relevant oilbased sealer product as appropriate

Noggins to comply with AS1684.2 (6.2.1.5).Vertical installation is recommended to have fixings at450 - 600mm maximum.

Refer AS1684 TimberFraming Manual for Span

tables/sizes of timbersubfloor bearers/joists

BB02-B1

Vertical fixed BE Board & Batten tobe mitred over noggin and lappedas pictured.

Moisturevapour barrier

or releventimpermeablewall underlay

as per NCC

End cuts to be mitred and flush joined.Cuts to be sealed with relevant sealerproduct as appropriate.

Screw/Nail fixing as per RadialTimber Supplies product fixinginformation specifications.Fix board 10mm min clear of joint.

Under lapped board (See BB01)Over lapped board (See BB01)

150m

m

50

6Steel flashing as per (NCC:3.5.3.6) as appropriate

Optional timber block under flashing attached to masonry wall withsuitable anchor. Timber to be minimum H3 or Class 2, or as appropriate.

Screw/Nail fixing as per Radial Timber Suppliesproduct fixing information specifications.Fix board 10mm min clear of end.

Clearance distance to finished Ground Level - 150mm Min distanceas per (NCC: 3.1.2.3) and/or (AS2870: 5.2.2)

Bottom side of board to be undercut min 150 angle to form drip edgeon vertical fixed boards. Cladding to be min 50mm past Floor Level6mm mincapillary gap

betweencladding &slab edge

Under lapped board (See BB01)Over lapped board (See BB01)

BB02:A - BE Board & Batten Noggin Fixing SOG1:151.0

BB02:B1 - Vertical Board & Batten Bottom Flashing1:52.1

BB02:B - BE Board & Batten Noggin Fixing Timber Sub-Floor1:152.0

BB02:A1 - Vertical Board & Batten Mitre Join1:51.1

BB02:A2 - Vertical Board & Batten Bottom Flashing1:51.2

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

NOTE:Radial Timber Product specifications noted here-in are manufacturers information for guidancepurposes only. Adherance with applicable Building Acts, Building Regulations,National Construction Codes, Local Government Regulations/Planning, Australian Standardsmust take precedence.

IMPORTANT:Refer to Radial Timber Product specifications for further fixing information:www.radialtimbers.com.au

GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Radial Board & Batten Wall (Batten) Fixing Details

BB03

0418-Feb-17

100

Typical polyethelene filmmoisture barrier

(See AS2870 for further details)

Timber framing as perAS1684

End cuts to be sealed with relevant oilbased sealer product as appropriate

Timber or plastic shim spacer as appropriate (Min 10mm)

Moisture Vapour barrier or relevantimpermeable wall underlay as perNCC and AS1684

Noggins at 600mm centres max.Noggins to comply with AS1684.2 (6.2.1.5)

Stagger cutting joins over alternating noggins.End cuts to be mitred and flush joined. Cuts to besealed with relevant sealer product as appropriate

Vertical Bevelled Edge Board & Battenboards fixed to horizontal timber battens.

Under lapped Board (See BB01)Over lapped board (See BB01)

Timber Battens: Vertical installation is recommended to havefixings at 450 - 600mm maximum. Minimum H2 or Class 3.

150mm Min distance as per(NCC: 3.1.2.3) and/or (AS2870: 5.2.2)

BB03:A2

BB03:A1

50

End cuts to be sealed withrelevant oil based sealer productas appropriate.Optional (Recommended):Bottom side of board to beundercut min 150 angle to formdrip edge on vertical fixed boards.Cladding to be min 50mm pastFloor Level

Flashing as appropriate

Under lapped board (See BB01)Over lapped board (See BB01)

Width

Over

all D

epth

Depth

Foo

ting

Fill

Min H

eight

Timber framing as perAS1684

Typical Particleboard sheetinglaid over timber floor Joists

(See AS1860.2)

Typical timber bearer

Min sub floor height as perNCC 3.4.1 Sub Floor Ventillation.Height taken from bottom of bearer

to Ground Level (GL)

Typical timber floor joist

Stump & Footing size refer to:AS1684 Timber Framing Manual &/or

AS2870 Residential Slabs & Footings(or Engineers specifications where applicable)

Termite cap on top of stump as perNCC 3.1.3 Termite Management &AS3600 Termite Management

Typical Timber Barge Boardsattached to cleat on side of stump

Typical concrete stump

Vertical Bevelled Edge Board & Battenboards fixed to horizontal timber battens.

End cuts to be sealed with relevant oilbased sealer product as appropriate

Moisture Vapour barrier or relevantimpermeable wall underlay as perNCC and AS1684

Stagger cutting joins over alternating noggins.End cuts to be mitred and flush joined. Cuts to besealed with relevant sealer product as appropriate

Noggins at 600mm centres max.Noggins to comply with AS1684.2 (6.2.1.5)

Under lapped Board (See BB01)Over lapped board (See BB01)

Timber Battens: Vertical installation is recommended to havefixings at 450 - 600mm maximum. Minimum H2 or Class 3.

Refer AS1684 TimberFraming Manual for Span

tables/sizes of timbersubfloor bearers/joists

BB03:B1

BB03:B2

Vertical fixed shiplap to be mitredover batten and lapped as pictured

Moisture vapour barrier orrelevant impermeable wallunderlay as per NCC &AS1684

Cuts to be mitred and flush joined.Cuts to be sealed with relevantsealer product as appropriate

Timber batten, size asappropriate. Timber battensat 600mm centres max.Minimum H2 or Class 3Timber or plastic shimpacker over vertical stud,width as appropriate studsize (Min 10mm thickness)

Screw/Nail fixing as per RadialTimber Supplies product fixinginformation specifications.Fix board 10mm min clear of joint.

Under lapped board (See BB01)Over lapped board (See BB01)

35

35

10

75

Typical timber packing shim 10mmthickness. Packing shim used forpacking horizontal fixing battens toalleviate and ventillate any moisturebuild up between moisture vapourbarrier and timber cladding.

This can easily docked by customerfrom studs, etc;

37

75

54

12 13 12

10

Typical plastic horseshoe packingshim 10mm thickness. Packingshim used for packing horizontalfixing battens to alleviate andventillate any moisture build upbetween moisture vapour barrierand timber cladding

50

Steel flashing as per (NCC:3.5.3.6)as appropriate

Fixing as appropriate(See NCC Vol 1: 3.5.3.2 Timber Cladding)and Radial Timber fixing recommendations(www.radialtimbers.com.au)

Typical timber bearer

Termite cap as perNCC 3.1.3 Termite Management &AS3600 Termite Management

Typical Timber Barge Boards attached to cleat onside of stump

Typical timber joist

Typical Concreteor timber stump

Typical timber frame stud

Typical Particleboardsheeting

Moisture vapourbarrier or releventimpermeable wallunderlay as per NCC

End cuts to be sealed with relevant oil basedsealer product as appropriate.Bottom side of board to be undercut min150 angle to form drip edge on vertical fixedboards.Cladding to be min 50mm past Floor Level

Timber or plastic shim spacer as appropriate(Min 10mm)

Typical timber batten as appropriate

Under lapped board (See BB01)Over lapped board (See BB01)

Refer AS1684 Timber FramingManual for Span tables/sizes of

timber subfloor bearers/joists

BB03:A - BE Board & Batten Batten Fixing SOG1:151.0

BB03:A2 - Vertical Board & Batten End Flashing1:51.2

BB03:B - BE Board & Batten Batten Fixing Timber Sub-Floor1:152.0

BB03:A1 & BB03:B1 - Vertical B&B Mitre Join1:51.1/2.1

Typical Timber Packer1:54.0

Typical Plastic Packer1:53.0

BB03:B2 - Vertical Board & Batten End Flashing1:52.2

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

NOTE:Radial Timber Product specifications noted here-in are manufacturers information for guidancepurposes only. Adherance with applicable Building Acts, Building Regulations,National Construction Codes, Local Government Regulations/Planning, Australian Standardsmust take precedence.

IMPORTANT:Refer to Radial Timber Product specifications for further fixing information:www.radialtimbers.com.au

GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Radial Board & Batten External Corner Details

BB04

0418-Feb-17

50

75

Corner stud blocking as per timberframing standard AS1684

Corner flashing as perNCC: 3.5.3.6 Flashings to

wall openings

Typical 75/100mm Board &Batten cladding

Weather resistant flexible sealant betweencladding & corner stop as appropriateSquare cut cladding to suit corner stop as appropriate

Moisture vapourbarrier or relevantimpermeable wallunderlay as per NCC& AS1684

Typical Board & Batten100/100mm cladding

Alternative 75x50mm (x1)SQE corner stop butt join

Typical fixingto timber stud

Typical timber stud.Spacing at 600mm centers max.

Alternative 75x50mm (x1) SQETimber corner stop

Typical Standard Board & Batten profile(Example 75mm & 100mm BE shown)

Typical Standard Board & Batten profile(Example 100mm & 100mm BE shown)

BB04:A2

Typical timber stud.Spacing at 600mm centers max.

Typical Standard Board & Batten profile(Example 75mm & 100mm BE shown)

Typical Standard Board & Batten profile(Example 100mm & 100mm BE shown)

Alternative 75x50mm (x2) SQETimber corner stop

BB04:A1

Typical 75/100mmBoard & Battencladding

Typical Board & Batten100/100mm cladding Corner stud blocking as per timberframing standard AS1684

Weather resistant flexible sealant betweencladding & corner stop as appropriate

Moisture vapourbarrier or relevantimpermeable wallunderlay as per NCC& AS1684

Corner flashing as perNCC: 3.5.3.6 Flashings to

wall openings

Square cut cladding to suit corner stop as appropriate

Typical 75x50mm (x2)SQE corner stop butt join

Typical 75/100mmBoard & Battencladding

Typical Board & Batten100/100mm cladding Corner stud blocking as per timberframing standard AS1684

Moisture vapourbarrier or relevantimpermeable wallunderlay as per NCC& AS1684

Corner flashing as perNCC: 3.5.3.6 Flashings to

wall openings

Alternate option ofripping square edgeand butt join boards toexternal corner Typical 75/100mm

Board & Battencladding

Typical Board & Batten100/100mm cladding Corner stud blocking as per timberframing standard AS1684

Weather resistant flexible sealant betweencladding & corner stop as appropriate

Moisture vapourbarrier or relevantimpermeable wallunderlay as per NCC& AS1684

Corner flashing as perNCC: 3.5.3.6 Flashings to

wall openings

Square cut cladding to suit corner stop as appropriateTypical 75x50mm (x2)

SQE corner stop butt join

Builder to cut rebate tocorner stop as required

Alternate option of ripping bevellededge to match cladding

BB04:B1 - Board & Batten Alternate External Corner Details1:52.1

BB04:B - Alternate Board & Batten External Corner1:152.0

BB04:A - Typical Board & Batten External Corner1:151.0

BB04:A1 - Board & Batten External Corner Details1:51.1

BB04:A2 - Board & Batten Alternate External Corner Details1:51.2

BB04:B2 - Board & Batten Alternate External Corner Details1:52.2

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

NOTE:Radial Timber Product specifications noted here-in are manufacturers information for guidancepurposes only. Adherance with applicable Building Acts, Building Regulations,National Construction Codes, Local Government Regulations/Planning, Australian Standardsmust take precedence.

IMPORTANT:Refer to Radial Timber Product specifications for further fixing information:www.radialtimbers.com.au

GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Board & Batten Window (Noggin Fixing) Flashing Details

BB06

0418-Feb-17

15

Flashing as per NCC 3.5.3.6: Flashings to Wall Openings and/orwindow manufacturers specifications.

Flashing to have adequate fall for drainage as appropriate (Eg; 150)

Timber Architrave

Typical Impervious sealing strip(See specific window manufactuers specifications for further information)

Moisture vapour barrier or relevantimpermeable wall underlay as per

NCC & AS1684

Moisture vapour barrier or relevantimpermeable wall underlay as per

NCC & AS1684

Timber Framing as per:AS1684.2 Timber Framed Construction (Part 6.2.3 Openings)

Min 15mm clearance between Lintel and window head.

Typical stud frame (See AS1684 Timber Framing Manual)

Typical plasterboard sheet as required

Timber reveal, size as appropriate

Timber Architrave

Typical Radial Board & BattenTypical stud frame (Checked out for timber window lintel as per AS 1684)

Typical plasterboard sheet as required

Timber reveal, size as appropriate

Typical timber window lintel(See AS 1684 Timber Framing Manual for sizes/spans)

Typical timber window ledger(See AS 1684 Timber Framing Manual for sizes/spans)

Fixing reveal to lintel and ledger (size as appropriate).Min 15mm clearance between Lintel and window head.

Over lapped board (See DT10)

Under lapped board (See DT10)

Flashing as per NCC 3.5.3.6: Flashings to Wall Openings and/orwindow manufacturers specifications.

Flashing to have adequate fall for drainage as appropriate (Eg; 150)

Over lapped board (See DT10)

Under lapped board (See DT10)

Typical Radial Board & Batten

TypicalWindow

Brackets & Fixings to support window structure as perwindow manufacturers or engineers specifica ons

NOTE: Window details are indictation of cladding fixing only.For specific details it is recommended to refer to window manufacturers details

WINDOWHEAD

WINDOW SILL

150

150

15

Low modulus sealant

Flashing as per NCC 3.5.3.6: Flashings to Wall Openings and/orwindow manufacturers specifications.

Flashing to have adequate fall for drainage as appropriate (Eg; 150)

Timber window head(See window manufacturers specifications)

Timber Architrave

Moisture vapour barrier or relevantimpermeable wall underlay as per

NCC & AS1684

Flashing as per NCC 3.5.3.6: Flashings to Wall Openings and/orwindow manufacturers specifications.

Flashing to have adequate fall for drainage as appropriate (Eg; 150)

Typical stud frame

Typical plasterboard sheet as required

Timber window sill(See window manufacturers specifications)

Timber Architrave

Moisture vapour barrier or relevantimpermeable wall underlay as per

NCC & AS1684

Typical stud frame (Checked out for timber window lintel as per AS 1684)

Typical plasterboard sheet as required

Typical timber window lintel(See AS 1684 Timber Framing Manual for sizes/spans)

Typical timber window ledger(See AS 1684 Timber Framing Manual for sizes/spans)

Over lapped board (See DT10)

Under lapped board (See DT10)

Typical Radial Board & Batten

Timber Framing as per:AS1684.2 Timber Framed Construction (Part 6.2.3 Openings)

Min 15mm clearance between Lintel and window head.

Typical Radial Board & Batten

Over lapped board (See DT10)

Under lapped board (See DT10)

TypicalWindow

Brackets & Fixings to support window structure as perwindow manufacturers or engineers specifica ons

NOTE: Window details are indictation of cladding fixing only.For specific details it is recommended to refer to window manufacturers details

WINDOWHEAD

WINDOW SILL

150

150

75

50

Typical stud frame (As per AS 1684)

Typical plasterboard sheet as required

Timber Architrave

Moisture vapour barrier or relevant impermeablewall underlay as per NCC & AS1684

Fix window window frame to vertical timber stud.Packer as required between reveal and stud

Flashing as per NCC: 3.5.3.6 Flashings to wall openings

Typical Radial horizontalBevelled Edge Board & Batten

Weather resistant flexible sealant betweencladding & corner stop as appropriate

Typical 75x50mm SQE stopbutt join to Radcon Bevelled Edge

Board & BattenUnder lapped board (See DT 10)

Over lapped board (See DT 10)

TypicalTimber

Window

Brackets & Fixings to support window structure as perwindow manufacturers or engineers specifica ons

NOTE: Window details are indictation of cladding fixing only.For specific details it is recommended to refer to window manufacturers details

75

50

Typical stud frame (As per AS 1684)

Typical plasterboard sheet as required

Timber Architrave

Moisture vapour barrier or relevant impermeablewall underlay as per NCC & AS1684

Fix window reveal to vertical timber stud.Packer as required between reveal and stud

Flashing as per NCC: 3.5.3.6 Flashings to wall openings

Typical 75x50mm SQE stopbutt join to Radcon Bevelled Edge

Board & Batten

Weather resistant flexible sealant betweencladding & corner stop as appropriate

Under lapped board (See DT 10)

Over lapped board (See DT 10)

Typical Radial horizontalBevelled Edge Board & Batten

TypicalAluminium

Window

Brackets & Fixings to support window structure as perwindow manufacturers or engineers specifica ons

NOTE: Window details are indictation of cladding fixing only.For specific details it is recommended to refer to window manufacturers details

BB06:A - Typical Board & Batten Aluminium Window Flashing Details Section (Noggin Fixing)1:51.0

BB06:B - Typical Board & Batten Timber Window Flashing Details Section (Noggin Fixing)1:52.0

BB06:B1 - Typical Board & Batten Timber Window Flashing Details Plan View1:52.1

BB06:A1 - Typical Board & Batten Aluminium Window Flashing Details Plan View1:51.1

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

IMPORTANT:Refer to Radial Timber Product specifications for further fixinginformation: www.radialtimbers.com.au

NCC Volume 2:3.5.3.6 Flashings to wall openingsOpenings in external wall cladding exposed to the weather must be flashed as follows:(a) All openings must be adequately flashed using materials that comply with AS/NZS 2904.(b) Flashings must be securely fixed at least 25 mm under the cladding and extend over theends and edges of the framing of the opening

NOTE: Same principles for fixing (As per details here-in)apply for horizontal clad or vertical clad shiplap fixing

TYPICAL TIMBER LINTEL OPTIONS FOR WINDOW OPENINGS (Below):AS 1684 (Timber Framing manual - Figure 6.8 Openings)

GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Board & Batten Window (Batten Fixing) Flashing Details

BB07

0418-Feb-17

15

Timber Architrave

Typical Impervious sealing strip(See specific window manufactuers specifications for further information)

Moisture vapour barrier or relevantimpermeable wall underlay as per

NCC & AS1684

Typical stud frame (See AS1684 Timber Framing Manual)

Typical plasterboard sheet as required

Timber reveal, size as appropriate

Timber Architrave

Typical plasterboard sheet as required

Timber reveal, size as appropriate

Typical timber window lintel(See AS 1684 Timber Framing Manual for sizes/spans)

Typical timber window ledger(See AS 1684 Timber Framing Manual for sizes/spans)

Fixing reveal to lintel and ledger (size as appropriate).Min 15mm clearance between Lintel and window head.

Moisture vapour barrier or relevantimpermeable wall underlay as per

NCC & AS1684

Over lapped board (See DT10)

Under lapped board (See DT10)

Min 15mm clearance between Lintel and window head.

Typical Radial Board & BattenTypical stud frame (Checked out for timber window lintel as per AS 1684).Timber Framing as per:AS1684.2 Timber Framed Construction (Part 6.2.3 Openings)

Flashing as per NCC 3.5.3.6: Flashings to Wall Openings and/orwindow manufacturers specifications.

Flashing to have adequate fall for drainage as appropriate (Eg; 150)

Over lapped board (See DT10)

Under lapped board (See DT10)

Typical Radial Board & Batten

Typical timber batten and packer: Timber or plastic shim spaceras appropriate (Min 10mm).Vertical installation is recommended to have fixings at 450 -600mm maximum. Minimum H2 or Class 3.

Typical timber batten and packer: Timber or plastic shim spacer asappropriate (Min 10mm).Vertical installation is recommended to have fixings at 450 - 600mmmaximum. Minimum H2 or Class 3.

TypicalWindow

Brackets & Fixings to support window structure as perwindow manufacturers or engineers specifica ons

NOTE: Window details are indictation of cladding fixing only.For specific details it is recommended to refer to window manufacturers details

WINDOWHEAD

WINDOW SILL

150

150

15

Timber Architrave

Typical Impervious sealing strip(See specific window manufactuers specifications for further information)

Moisture vapour barrier or relevantimpermeable wall underlay as per

NCC & AS1684

Typical stud frame (See AS1684 Timber Framing Manual)

Typical plasterboard sheet as required

Timber reveal, size as appropriate

Timber Architrave

Typical plasterboard sheet as required

Timber reveal, size as appropriate

Typical timber window lintel(See AS 1684 Timber Framing Manual for sizes/spans)

Typical timber window ledger(See AS 1684 Timber Framing Manual for sizes/spans)

Fixing reveal to lintel and ledger (size as appropriate).Min 15mm clearance between Lintel and window head.

Moisture vapour barrier or relevantimpermeable wall underlay as per

NCC & AS1684

Over lapped board (See DT10)

Under lapped board (See DT10)

Min 15mm clearance between Lintel and window head.

Typical Radial Board & BattenTypical stud frame (Checked out for timber window lintel as per AS 1684).Timber Framing as per:AS1684.2 Timber Framed Construction (Part 6.2.3 Openings)

Flashing as per NCC 3.5.3.6: Flashings to Wall Openings and/orwindow manufacturers specifications.

Flashing to have adequate fall for drainage as appropriate (Eg; 150)

Over lapped board (See DT10)

Under lapped board (See DT10)

Typical Radial Board & Batten

Typical timber batten and packer: Timber or plastic shim spaceras appropriate (Min 10mm).Vertical installation is recommended to have fixings at 450 -600mm maximum. Minimum H2 or Class 3.

Typical timber batten and packer: Timber or plastic shim spacer asappropriate (Min 10mm).Vertical installation is recommended to have fixings at 450 - 600mmmaximum. Minimum H2 or Class 3.

TypicalWindow

Brackets & Fixings to support window structure as perwindow manufacturers or engineers specifica ons

NOTE: Window details are indictation of cladding fixing only.For specific details it is recommended to refer to window manufacturers details

WINDOWHEAD

WINDOW SILL

150

150

45

75

50

Typical stud frame (As per AS 1684)

Typical plasterboard sheet as required

Timber Architrave

Moisture vapour barrier or relevant impermeablewall underlay as per NCC & AS1684

Fix window reveal to vertical timber stud.Packer as required between reveal and stud

Typical timber batten and packer.Timber battens at 600mm centres max.Minimum H2 or Class 3

Typical 45x19mm SQE stopbutt join to timber batten

Flashing as per NCC: 3.5.3.6 Flashings to wall openings

Typical 75x50mm SQE stopbutt join to Radcon Bevelled Edge

Board & Batten

Weather resistant flexible sealant betweencladding & corner stop as appropriate

Under lapped board (See DT 10)Over lapped board (See DT 10)

Typical Radial horizontalBevelled Edge Board & Batten

Typical batten packer

TypicalAluminium

Window

Brackets & Fixings to support window structure as perwindow manufacturers or engineers specifica ons

NOTE: Window details are indictation of cladding fixing only.For specific details it is recommended to refer to window manufacturers details

45

75

50

Typical stud frame (As per AS 1684)

Typical plasterboard sheet as required

Timber Architrave

Moisture vapour barrier or relevant impermeablewall underlay as per NCC & AS1684

Fix window reveal to vertical timber stud.Packer as required between reveal and stud

Typical timber batten and packer.Timber battens at 600mm centres max.Minimum H2 or Class 3

Typical 45x19mm SQE stopbutt join to timber batten

Flashing as per NCC: 3.5.3.6 Flashings to wall openings

Typical 75x50mm SQE stopbutt join to Radcon Bevelled Edge

Board & Batten

Weather resistant flexible sealant betweencladding & corner stop as appropriate

Under lapped board (See DT 10)Over lapped board (See DT 10)

Typical Radial horizontalBevelled Edge Board & Batten

Typical batten packer

TypicalAluminium

Window

Brackets & Fixings to support window structure as perwindow manufacturers or engineers specifica ons

NOTE: Window details are indictation of cladding fixing only.For specific details it is recommended to refer to window manufacturers details

BB07:A - Typical Board & Batten Aluminium Window Flashing Details Section (Batten Fixing)1:51.0

BB07:B - Typical Board & Batten Timber Window Flashing Details Section (Batten Fixing)1:52.0

BB07:B1 - Typical Board & Batten Timber Window Flashing Details Section1:52.1

BB07:A1 - Typical Board & Batten Aluminium Window Flashing Details Section1:51.1

TYPICAL TIMBER LINTEL OPTIONS FOR WINDOW OPENINGS (Below):AS 1684 (Timber Framing manual - Figure 6.8 Openings)

IMPORTANT:Refer to Radial Timber Product specifications for further fixinginformation: www.radialtimbers.com.au

NCC Volume 2:3.5.3.6 Flashings to wall openingsOpenings in external wall cladding exposed to the weather must be flashed as follows:(a) All openings must be adequately flashed using materials that comply with AS/NZS 2904.(b) Flashings must be securely fixed at least 25 mm under the cladding and extend over theends and edges of the framing of the opening

NOTE: Same principles for fixing (As per details here-in)apply for horizontal clad or vertical clad shiplap fixing

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Radial B&B Wall Overhang/Pitch Roof Details (Batten Fixing)

BB08

0418-Feb-17

32

D

Moisture Vapour barrier or relevant impermeablewall underlay as per NCC and AS1684

Timber moulding (Eg:Quad or other as appropriate)

Eaves Lining Cement Sheet(Soffit) or as appropriate

Typical Soffit bearer (70x35mm) - Fixed to side of rafter(Size as per AS1684:Timber Framing)

Typical Fascia board

Optional Soffit bearer hanger (See AS1684:Timber Framing)

Typical Noggin (70x35mm) fixed between soffit bearers

D/3 Max

Typical Rafter

Typical roofing batten

Typical stud wall top plate

Moisture Vapour barrier or relevant impermeablewall underlay as per NCC and AS1684

Typical vertical wall stud (As per AS 1684)

Typical particleboardflooring over floor joist

Typical Soffit liningattached to battens

Typical vertical wall stud (As per AS 1684)

Flashing as per NCC 3.5.3.6: Flashings to Wall Openings and/orArchitects/Engineers specifications.Flashing to have adequate fall for drainage as appropriate (Eg; 150)

Optional (Recommened):End cuts to be sealed with relevant oil based sealer product as appropriate.Bottom side of boards to be undercut min 150 angle to form drip edge onboards and 5-10mm clearance between flashing and boards to alleviate anymositure trapping issues

Typical Radial Board & Batten

Over lapped board(See DT10)

Under lappedboard (See DT10)

Optional supporting postby Architect/Engineer

Typical Radial Board & Batten

Over lapped board(See DT10)

Under lappedboard (See DT10)

Noggins to comply with AS1684.2 (6.2.1.5).Vertical installation is recommended to havefixings at 450 - 600mm maximum.

Noggins to comply with AS1684.2 (6.2.1.5).Vertical installation is recommended to havefixings at 450 - 600mm maximum.

D/3 = Not more than 1/3 to be cutfrom rafter for birdsmouth cut

150

Typical Floor Joist Beam as perArchitect/Engineer

NOTE: Details are indictation of cladding fixing only.

Vertical fixed shiplap to be mitredover batten and lapped as pictured

Moisture vapour barrier orrelevant impermeable wallunderlay as per NCC &AS1684

Cuts to be mitred and flush joined.Cuts to be sealed with relevantsealer product as appropriate

Timber batten, size asappropriate. Timber battensat 600mm centres max.Minimum H2 or Class 3Timber or plastic shimpacker over vertical stud,width as appropriate studsize (Min 10mm thickness)

Screw/Nail fixing as per RadialTimber Supplies product fixinginformation specifications.Fix board 10mm min clear of joint.

Under lapped board (See BB01)Over lapped board (See BB01)

35

35

10

75

Typical timber packing shim 10mmthickness. Packing shim used forpacking horizontal fixing battens toalleviate and ventillate any moisturebuild up between moisture vapourbarrier and timber cladding.

This can easily docked by customerfrom studs, etc;37

75

54

12 13 12

10

Typical plastic horseshoe packingshim 10mm thickness. Packingshim used for packing horizontalfixing battens to alleviate andventillate any moisture build upbetween moisture vapour barrierand timber cladding

BB08:A - Typical Board & Batten Pitch Roof Detail Section (Batten Fixing)1:101.0

BB03:A1 & BB03:B1 - Vertical B&B Mitre Join1:51.1

Typical Timber Packer1:43.0

Typical Plastic Packer1:42.0

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

NOTE:Radial Timber Product specifications noted here-in are manufacturers information for guidancepurposes only. Adherance with applicable Building Acts, Building Regulations,National Construction Codes, Local Government Regulations/Planning, Australian Standardsmust take precedence.

IMPORTANT:Refer to Radial Timber Product specifications for further fixing information:www.radialtimbers.com.au

GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Radial B&B Wall Overhang/Pitch Roof Details (Noggin Fixing)

BB09

0418-Feb-17

32

D

Moisture Vapour barrier or relevant impermeablewall underlay as per NCC and AS1684

Timber moulding (Eg:Quad or other as appropriate)

Eaves Lining Cement Sheet(Soffit) or as appropriate

Typical Soffit bearer (70x35mm) - Fixed to side of rafter(Size as per AS1684:Timber Framing)

Typical Fascia board

Optional Soffit bearer hanger (See AS1684:Timber Framing)

Typical Noggin (70x35mm) fixed between soffit bearers

D/3 Max

Typical Rafter

Typical roofing batten

Typical stud wall top plate

Moisture Vapour barrier or relevant impermeablewall underlay as per NCC and AS1684

Typical vertical wall stud (As per AS 1684)

Typical particleboardflooring over floor joist

Typical Soffit liningattached to battens

Typical vertical wall stud (As per AS 1684)

Flashing as per NCC 3.5.3.6: Flashings to Wall Openings and/orArchitects/Engineers specifications.Flashing to have adequate fall for drainage as appropriate (Eg; 150)

Optional (Recommened):End cuts to be sealed with relevant oil based sealer product as appropriate.Bottom side of boards to be undercut min 150 angle to form drip edge onboards and 5-10mm clearance between flashing and boards to alleviate anymositure trapping issues

Typical Radial Board & Batten

Over lapped board(See DT10)

Under lappedboard (See DT10)

Optional supporting postby Architect/Engineer

Typical Radial Board & Batten

Over lapped board(See DT10)

Under lappedboard (See DT10)

Noggins to comply with AS1684.2 (6.2.1.5).Vertical installation is recommended to havefixings at 450 - 600mm maximum.

Noggins to comply with AS1684.2 (6.2.1.5).Vertical installation is recommended to havefixings at 450 - 600mm maximum.

D/3 = Not more than 1/3 to be cutfrom rafter for birdsmouth cut

150

Typical Floor Joist Beam as perArchitect/Engineer

NOTE: Details are indictation of cladding fixing only.

Vertical fixed BE Board & Batten tobe mitred over noggin and lappedas pictured.

Moisturevapour barrier

or releventimpermeablewall underlay

as per NCC

End cuts to be mitred and flush joined.Cuts to be sealed with relevant sealerproduct as appropriate.

Screw/Nail fixing as per RadialTimber Supplies product fixinginformation specifications.Fix board 10mm min clear of joint.

Under lapped board (See BB01)Over lapped board (See BB01)

BB09:A - Typical Board & Batten Pitch Roof Detail Section (Noggin Fixing)1:101.0

BB02:A1 - Vertical Board & Batten Mitre Join1:51.1

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

NOTE:Radial Timber Product specifications noted here-in are manufacturers information for guidancepurposes only. Adherance with applicable Building Acts, Building Regulations,National Construction Codes, Local Government Regulations/Planning, Australian Standardsmust take precedence.

IMPORTANT:Refer to Radial Timber Product specifications for further fixing information:www.radialtimbers.com.au

GSPublisherEngine 0.2.100.100

GENERAL NOTES:

1. Do not scale Drawings. If drawings are in question ordiscrepancy, the builder shall be responsible for obtainingclarification from the building designer and or buildingsurveyor before continuing with construction.

2. All dimensions relating to existing conditions shall be fieldverified.

3. Where otherwise specified all products shall be installedaccording to Radial Timbers specifications. This applies notwithstanding any relevant Building Act, Regulation, BuildingCode of Australia, Local GovernmentRegulation/Requirement and Australian Standard.

4. Radial Timbers recommends the following gap spacing forV/Join Shiplap:· 45mm & 70mm - 3mm Gap spacing· 90mm & 110mm - 5mm Gap spacing

5. All external timbers to be treated against weather exposureto current AS 1604 specifications or no less than durabilityClass 1 In-Ground/Class 2 Above Ground as per AS 5604Timber Natural Durability Ratings.

6. All external steel & fixings to be a minimum of Hot DipGalvanized or equivalent corrosion protection to AS 2311 &2312 unless within 1Km from a salt water environment thenMarine grade Stainless steel is to be used, except wherenoted otherwise by the NCC.

7. All Residential timber framing, bracing & tie downs are to bein accordance to AS 1684 (Commercial constructionspecifications to be provided by Engineer).

8. Compliance with the relevant National Construction CodeOf Australia (NCC) Volume 1 & or Volume 2 is mandatory(Not limited to) & theGUIDE TO STANDARDS & TOLERANCES.

9. Compliance with the (NCC) Volume 1:3.5.3.2 Timber Cladding & 3.5.3.6 Flashingsto wall openingsOpenings in external wall cladding exposed to the weathermust be flashed as follows:

(a) All openings must be adequately flashed using materialsthat comply with AS/NZS 2904.

(b) Flashings must be securely fixed at least 25 mm under thecladding

10. Compliance with the following Australian Standards ismandatory (Not limited to):

AS 1684 TIMBER FRAMED CONSTRUCTIONAS 5604 NATURAL TIMBER DURABILITYAS 3959 CONSTRUCTION IN BUSHFIRE AREASAS 2796.1 TIMBER HARDWOOD -SAWN & MILLED PRODUCTS(PRODUCT SPECIFICATION)AS 2047 WINDOWS IN BUILDINGS AS 2870 RESIDENTIAL SLABS & FOOTINGSAS 1250 THE USE OF STEEL IN STRUCTURESAS 4100 STEEL STRUCTURESAS 2311 PAINTING OF BUILDINGS AS 3600 TERMITE MANAGEMENTAS 1170 STRUCTURAL DESIGN ACTIONSAS 1428 DESIGN FOR ACCESS AND MOBILITYAS 1675 FIXED PLATFORMS, WALKWAYS, STAIRWAYSAND LADDERS - DESIGN, CONSTRUCTION ANDINSTALLATION

11. All underground services (Sewer, Drainage, Gas, Electric,telecommunications, etc;) to be determined on site & fromrelevant authority records, prior to commencement of anyconstruction.

A2 - Not To Scale

RADIAL TIMBER SALES12 PARK DRIVE,DANDENONG SOUTH 3175PH: (03) 9768 2100FAX: (03) 9768 2177EMAIL: sales@radialtimbers.com.auWEB: www.radialtimbers.com.au

DRAWING NAME:THE BUILDER SHALL CHECK AND VERIFY ALL DIMENSIONS ANDNOTIFY ALL ERRORS AND OMISSIONS TO THE DESIGNER.DRAWINGS ARE NOT TO BE USED FOR CONSTRUCTION UNTILISSUED BY THE DESIGNER FOR CONSTRUCTION.DO NOT SCALE DRAWINGS. USE FIGURED DIMENSIONS ONLY.FIXING DETAILS:REFER TO RADIAL TIMBERS RECOMMENDED FIXINGS(www.radialtimbers.com.au)

NOTES:

DATE:

SCALE:

REVISION:

DWG NO:

REVISION:

DWG NO:

Radial Board & Batten Wall/Skillion Roof Flashing Details

BB10

0418-Feb-17

Vertical fixed shiplap to be mitredover batten and lapped as pictured

Moisture vapour barrier orrelevant impermeable wallunderlay as per NCC &AS1684

Cuts to be mitred and flush joined.Cuts to be sealed with relevantsealer product as appropriate

Timber batten, size asappropriate. Timber battensat 600mm centres max.Minimum H2 or Class 3Timber or plastic shimpacker over vertical stud,width as appropriate studsize (Min 10mm thickness)

Screw/Nail fixing as per RadialTimber Supplies product fixinginformation specifications.Fix board 10mm min clear of joint.

Under lapped board (See BB01)Over lapped board (See BB01)

35

35

10

75

Typical timber packing shim 10mmthickness. Packing shim used forpacking horizontal fixing battens toalleviate and ventillate any moisturebuild up between moisture vapourbarrier and timber cladding.

This can easily docked by customerfrom studs, etc;

37

75

54

12 13 12

10

Typical plastic horseshoe packingshim 10mm thickness. Packingshim used for packing horizontalfixing battens to alleviate andventillate any moisture build upbetween moisture vapour barrierand timber cladding

Vertical fixed BE Board & Batten tobe mitred over noggin and lappedas pictured.

Moisturevapour barrier

or releventimpermeablewall underlay

as per NCC

End cuts to be mitred and flush joined.Cuts to be sealed with relevant sealerproduct as appropriate.

Screw/Nail fixing as per RadialTimber Supplies product fixinginformation specifications.Fix board 10mm min clear of joint.

Under lapped board (See BB01)Over lapped board (See BB01)

75

Moisture Vapour barrier or relevant impermeablewall underlay as per NCC and AS1684

Noggins at 600mm centres max.Noggins to comply with AS1684.2 (6.2.1.5)

Typical roof framingbatten (See AS1684) Typical sheet roofing

Typical Rafter Typical stud wall top plate

Typical vertical wall stud

Typical flashing over roofcladding and rafter

Typical Radial Board & Batten

Over lapped board (See DT10)

Under lapped board (See DT10)

Typical roof framingbatten (See AS1684)

Timber Battens: Vertical installation isrecommended to have fixings at 450 - 600mmmaximum. Minimum H2 or Class 3.

75mm Minimum overlap of flashing

Moisture Vapour barrier or relevant impermeablewall underlay as per NCC and AS1684

Typical roof framingbatten (See AS1684) Typical sheet roofing

Typical fascia board

Typical Rafter Typical stud wall top plate

Typical vertical wall stud

Typical flashing over roofcladding and fascia board

Typical Radial Board & Batten

Over lapped board (See DT10)

Under lapped board (See DT10)

Noggins to comply with AS1684.2 (6.2.1.5).Vertical installation is recommended to havefixings at 450 - 600mm maximum.

BB03:A1 & BB03:B1 - Vertical B&B Mitre Join1:42.1

Typical Timber Packer1:44.0

Typical Plastic Packer1:43.0

BB02:A1 - Vertical Board & Batten Mitre Join1:41.1

BB10:B - Typical Board & Batten Skillion Roof Detail Section (Batten Fixing)1:102.0

BB10:A - Typical Board & Batten Skillion Roof Detail Section (Noggin Fixing)1:101.0

NOTE:Termite Treatment in accordance with AS3600 required.Installer to comply with AS3959 - Construction In Bushfire areas.

NOTE:Radial Timber Product specifications noted here-in are manufacturers information for guidancepurposes only. Adherance with applicable Building Acts, Building Regulations,National Construction Codes, Local Government Regulations/Planning, Australian Standardsmust take precedence.

IMPORTANT:Refer to Radial Timber Product specifications for further fixing information:www.radialtimbers.com.au

RTS Fixing Details - 1 - ViewsRTS DetailsBoard & BattenBB01 Typical Radial Board & Batten DetailsBB02 Radial Board & Batten Wall (Noggin) Fixing DetailsBB03 Radial Board & Batten Wall (Batten) Fixing DetailsBB04 Radial Board & Batten External Corner DetailsBB06 Board & Batten Window (Noggin Fixing) Flashing DetailsBB07 Board & Batten Window (Batten Fixing) Flashing DetailsBB08 Radial B&B Wall Overhang/Pitch Roof Details (Batten Fixing)BB09 Radial B&B Wall Overhang/Pitch Roof Details (Noggin Fixing)BB10 Radial Board & Batten Wall/Skillion Roof Flashing Details