TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.
-
Upload
marybeth-walters -
Category
Documents
-
view
216 -
download
0
Transcript of TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.
![Page 1: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/1.jpg)
TYPE I AND TYPE IICIDH
The Good, the Bad, and the Ugly
2 May 2008Sacramento, CA
Alan Macnab
![Page 2: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/2.jpg)
OUTLINE
• Installation Issues• Rebar Spacing• Flow Research• Caltrans Rebar Design• Concrete Cover• Type I issues• Type II Issues• Other States Solutions• Recommendations
![Page 3: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/3.jpg)
![Page 4: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/4.jpg)
![Page 5: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/5.jpg)
![Page 6: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/6.jpg)
![Page 7: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/7.jpg)
![Page 8: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/8.jpg)
Fully Cased Rotator Method
3,000 RDM Rotator and Excavation Crane
![Page 9: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/9.jpg)
SLURRY METHOD OF CONSTRUCTION
![Page 10: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/10.jpg)
Polymer Slurry System
![Page 11: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/11.jpg)
![Page 12: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/12.jpg)
![Page 13: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/13.jpg)
From ACI 336.1• 3.4.6 Reinforcement cover shall be not less than 3 in.• (75 mm) where exposed to soil and not less than 4 in. (100• mm) in cased piers where the casing is to be withdrawn. Provide• spacer rollers acceptable to the Owner’s Representative• to maintain cover.• 3.4.7 Splice vertical reinforcing steel in accordance with• ACI 318 for compression or tension. Submit splice details.• 3.4.8 Weld reinforcing bars in accordance with AWS• D1.4. Use AWS-certified welders.
• 3.4.9 The minimum clear distances between reinforcement, including lapped bars, shall be 4 in. (100 mm) or four times the maximum aggregate size, whichever is larger.
• 3.4.10 Place reinforcement before pier concreting begins,• unless otherwise directed by the Owner’s Representative-• Geotechnical Engineer.• 3.4.11 Limit reinforcing-steel vertical movement during• casing withdrawal to 6 in. (150 mm).
![Page 14: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/14.jpg)
![Page 15: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/15.jpg)
Deese & Mullins, 2005
![Page 16: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/16.jpg)
• 49‑4 CAST‑IN‑PLACE CONCRETE PILES• 49‑4.01 DESCRIPTION• Cast-in-place concrete piles shall consist of one of the following:• A. Steel shells driven permanently to the required nominal resistance and penetration and filled with
concrete.• B. Steel casings installed permanently to the required penetration and filled with concrete.• C. Drilled holes filled with concrete.• D. Rock sockets filled with concrete.• The drilling of holes shall conform to the provisions in these specifications. Concrete filling for cast-in-place
concrete piles is designated by compressive strength and shall have a minimum 28‑day compressive strength of
3,600 psi. At the option of the Contractor, the combined aggregate grading for the concrete shall be either the one‑inch maximum grading, the 1/2‑inch maximum grading, or the 3/8‑inch maximum grading. Concrete shall conform to the provisions in Section 90, "Portland Cement Concrete," and Section 51, "Concrete Structures." Reinforcement shall conform to the provisions in Section 52, "Reinforcement."
• Cast‑in‑place concrete piles shall be constructed so that the excavation methods and the concrete placement procedures shall provide for placing the concrete against undisturbed material in a dry or dewatered hole.
• The concrete filling for cast‑in‑place concrete piles shall be dense and homogeneous. The methods used to place the concrete shall prevent segregation. Concrete placed in steel shells, dry drilled holes or dewatered drilled holes shall not be permitted to fall from a height greater than 8 feet without the use of adjustable length pipes or tubes unless the flow of concrete is directed into the center of the hole using a hopper and not allowed to strike the reinforcement, reinforcement bracing and other objects in the hole.
• Concrete filling for cast‑in‑place concrete piles shall be vibrated in the upper 15 feet of the pile.• Section 51‑1.10, "Concrete Deposited Under Water," shall not apply to cast‑in‑drilled‑hole concrete piling.• After placing concrete, the temporarily exposed surfaces of the cast‑in‑place concrete piles shall be cured in
conformance with the provisions in Section 90‑7.03, "Curing Structures."
![Page 17: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/17.jpg)
![Page 18: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/18.jpg)
(102) #14'sSPA. BTWN. BARS = 5× "
10' SHAFT - 2.0%
2.0% Steel 102 - #14’s 5 7/8” clr.
Bundling Steel
![Page 19: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/19.jpg)
Inspection Tubes
![Page 20: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/20.jpg)
![Page 21: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/21.jpg)
![Page 22: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/22.jpg)
![Page 23: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/23.jpg)
• 49‑4.03 DRILLED HOLES• Except for cast‑in‑place concrete piling for soundwalls and retaining walls, when
cast‑in‑place concrete piling is less than 2 feet in diameter, the Contractor may propose to increase the diameter and revise the pile tip elevation. The Contractor may propose to increase the diameter of cast‑in‑place concrete piling for soundwalls and retaining walls, but the pile tip elevations shall not be revised. No
• additional compensation or delays will be made for the Contractor's use of increased diameter cast‑in‑place concrete piling.
• The axis of the hole shall not deviate from plumb more than 11/2 inches per 10 feet of length.
• Care shall be taken during excavation to prevent disturbing the foundation material surrounding the pile. Equipment or methods used for excavating holes shall not cause quick soil conditions or cause scouring or caving of the hole. After excavation is begun, the pile shall be constructed expeditiously in order to prevent deterioration of the surrounding foundation material from air slaking or from the presence of water. Deteriorated foundation material, including material that has softened, swollen or degraded, shall be removed from the sides and the bottom of the hole and shall be disposed of. The bottom of the drilled hole shall be cleaned just before placing reinforcement or concrete to remove any loose sand, gravel, dirt, and drill cuttings.
![Page 24: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/24.jpg)
![Page 25: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/25.jpg)
AASHTO Recommendations(currently being balloted)
• Location tolerance– 2 feet diameter or less 3”– Over 2 feet, less than 5 feet 4”– 5 feet diameter or over 6”
• Cover– 3 feet diameter or less 3”– Over 3 feet, less than 5 feet 4”– 5 feet diameter or over 6”
![Page 26: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/26.jpg)
¢ SHAFT & COLUMN
PLA
STIC
HIN
GE
ZO
NE
SH
AFT-C
OLU
MN
CO
NN
EC
TIO
N
PE
RM
AN
EN
T C
AS
ING
TE
MP
OR
AR
YC
AS
ING
APPROX. GROUND
CASING SHORING
Shaft Terminology
Plastic Hinging ZoneCasing Shoring
Column to Shaft Connection
Permanent Casing
Temporary Casing
Stepped Shaft
WSDOT Shaft Design
![Page 27: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/27.jpg)
6"
¢ COLUMN
¢ N
EW
LIN
E
¢ PIER
¢ N
EW
LIN
E
¢ PIER
#5 #5
#5 #5
#10 #10
#11 BUNDLED #11 BUNDLED
8'-0"ø SHAFT 8'-0"ø SHAFT
Allowance for Construction Tolerance
•Preliminary selection of column size.Preliminary selection of column size.
•Select minimum shaft size based on column Select minimum shaft size based on column size.size.
![Page 28: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/28.jpg)
Recommendations
• Change shaft concrete to 3/8” aggregate• Implement a location tolerance for shafts• Permit construction joint at base of column
cage• Pour column cages in the dry• All rebar in wet pours to be spaced in
accordance with 13-22• Increase concrete cover to meet new
AASHTO recommendations
![Page 29: TYPE I AND TYPE II CIDH The Good, the Bad, and the Ugly 2 May 2008 Sacramento, CA Alan Macnab.](https://reader030.fdocuments.in/reader030/viewer/2022032723/56649d205503460f949f4b53/html5/thumbnails/29.jpg)
TYPE I AND TYPE IICIDH
The good, the Bad, and the Ugly
13 March 2008Sacramento, CA