RO-CLEAN DESMI A/S Hestehaven 61 - DK-5260 Odense S Denmark Tel. (+45) 65910201, Telefax (+45) 65481615

CVR-NR. 69 04 29 10 http://www.ro-cleandesmi.com

Original Instructions

OPERATORS MANUAL

DESMI VERTICAL ARCHIMEDES' SCREW SKIMMER

TYPE DESMI-TARANTULA

(Parts list no. 020682575/80)

Safety precaution when working with oil skimmer systems

- Carefully read this manual before connecting or starting the machines. Notice that it may not be possible to study the manual during operation of the machinery.

- Only connect skimmers and winders with power packs they have been delivered with or which have been approved on beforehand by Ro-Clean Desmi.

- Do not start combustion engines in closed or badly ventilated rooms or if there is a danger of hazardous atmospheres. Avoid breathing in of exhaust fumes.

- The machines are not ATEX approved and must not be used in explosive atmospheres.

- Only lift machines in for this purpose made lifting devices such as fork lift channels, lifting eyes or lifting handles.

- Stop engines and disconnect battery terminals and hydraulic hoses before maintaining the equipment.

- Stop all engines before connecting or disconnecting hydraulic hoses.

- Before starting the machine, make sure that nobody is in the danger area (moving parts on engine or machinery), that all safety guards are in place and that the operator has a clear view of the working area including personnel and machines connected to the power pack.

- Never use any spray starting aids.

- Keep all advice and warning stickers in legible condition.

- When stored or in operation on a ship secure all equipment safely to the deck.

- Operators must frequently train in the use of power pack / oil skimmer / Oil containment boom systems in order to work safely with these systems.

- Observe the hydraulic oil level and temperature frequently during operation.

- Stand in front of the control panel and keep safety distance to the sides of the power pack during operation. Do not lean against the machine as this may vibrate and the engine, exhaust pipe and fumes can be very hot.

- Never use power packs with detent control levers for powering boom winders.

- Always use ear protectors when operating power packs or hydraulic motors.

- Use safety gloves, safety shoes, and clothes during operation or maintenance.

- Sucking in of solid particles by air blower should at all times be avoided as these may be ejected from the discharge flange at high speed and cause injury.

- During operation all personnel must pay attention to the danger of falling due to oily surfaces and hoses between power packs and connected machinery.

- During deployment of skimmers the personnel must pay attention to the danger of skimmers and hoses being caught by moving/rotating element such as ships and ship screws.

- Keep a safety distance to skimmers of minimum 1,4 meter.

- The sound pressure level of skimmers in water or oil does not exceed 70 dB(A)

- When operating skimmers on land the safety area must be marked by barrier tape in a height of 1,0 meter and at least 1,4 meter from the skimmer.

- When testing skimmers on land make sure that these are grounded to avoid sparks from static electricity.

NOTE: Refer to user manuals for ancillary equipment.

TYPE: Type of the pump CODE: Fitter’s I.D. and parts list No. NO.: Serial No. WK.: Manufacturing week/year

MANUFACTURED BY: DESMI A/S DK-9400 Norresundby Phone +45 96 32 81 11 Telefax +45 98 17 54 99

WARNING ! This equipment can be dangerous if the safety precautions in this manual are not being followed. Do not use the equipment without being familiar with the safety precautions in this manual. The customer is responsible for accidents caused by the equipment, if the safety instructions are not being followed.

WARNING ! Keep away from the rotating pump screw and cutting knives. The pump screw/cutting knives are designed for cutting debris normally found at oil spill sites and will also cut off fingers and other limbs.

WARNING ! Always keep a safety distance to the skimmer/pump of minimum 2 m/7 ft. when the skimmer/pump is connected to the hydraulic power supply. Do not connect the hydraulic hoses to the power supply until you are ready for operation.

C O N T E N T S 1.0 IN GENERAL 2.0 TRANSPORTATION AND MOUNTING 2.1 Transportation of the skimmer 2.2 Mounting 3.0 RESPONSE TACTICS 3.1 General remarks 3.2 Oil spills at sea 4.0 OPERATION OF THE DESMI-TARANTULA SKIMMER 4.1 Operation principle 4.2 Before operation 4.3 Operation 4.4 Recovery after operation 5.0 INSPECTION AFTER OPERATION AND PREVENTATIVE MAINTENANCE 5.1 Clean the DESMI-TARANTULA skimmer 5.2 Inspection of the DOP-250 pump 5.3 Protection of the DESMI-TARANTULA skimmer 5.4 Preventative maintenance of the DESMI-TARANTULA flotation system 6.0 TROUBLESHOOTING 7.0 TECHNICAL SPECIFCATIONS FOR DESMI SKIMMER TYPE DESMI-TARANTULA 7.1 Parts list 682575 for Tarantula 7.2 Parts list 682580 for Tarantula with thrusters 8.0 DRAWINGS 7.1 Assembly drawing no. 481741 for Tarantula 7.2 Assembly drawing no. 481743 for Tarantula with thrusters 9.0 THRUSTERS - PART NO. 682178 9.1 Parts list 682178 9.2 Drawing 481577

1.0 IN GENERAL The DESMI-TARANTULA combination skimmer system is the new generation of

DESMI’s vertical Archimedes’ screw skimmers. The DESMI-TARANTULA combination skimmer is a high capacity light-weight ocean

skimmer which skims 250 m3/h with up to 200 mm automatic weir lip adjustment. It works efficiently in waves heights up to 3 metres.

The skimmer combination skimmer system consists of a WEIR skimmer, a BRUSH

DRUM skimmer and a DISC skimmer which means that the skimmer is very efficiency in all kinds of oil spills.

It is very easy to change between the different type of skimmers. The use of only a few parts makes it a simple skimmer, easy to assemble and easy

to maintain, resulting in low weight and high buoyancy/seaworthiness. Using two DESMI modified positive displacement Archimedes' screw pumps in

vertical design, type DOP-250, the DESMI-TARANTULA combination skimmer is able to efficiently recover light as well as heavy oil, also when mixed with debris normally found in connection with oil spills.

The skimmer is fitted with a flotation system to provide the necessary buoyancy.

Hydraulic power to the skimmer pumps is supplied through hydraulic hoses connected to the power supply or remote control box. A discharge hose connects the skimmer to the storage tank.

The hoses will not affect the buoyancy of the skimmer as they are equipped with their

own floats. The DESMI-TARANTULA skimmer is designed as an advancing skimmer to operate

in conjunction with a floating containment boom. Do not start the skimmer pump before a sufficient oil layer is collected (DESMI recommends a minimum of 2 cm (3/4”)). The recovery efficiency may vary from 50 to 100% subject to oil quantity (oil layer thickness), oil viscosity, boom make, wave conditions, towing speed, and maybe most important: The operator’s skill!

As an option the DESMI-TARANTULA skimmer is provided with two thrusters to

secure the best recovery position in the floating containment boom. The thrusters are hydraulically driven and controlled from the remote control box.

WARNING! This equipment is designed to cope with debris normally found in an oil spill, and can be dangerous if the safety precautions in this manual are not followed. Do not use the equipment without being familiar with the safety instructions. The customer is responsible for accidents caused by the equipment, if the safety instructions in this manual are not being followed.

2.0 TRANSPORTATION AND MOUNTING 2.1 Transportation of the skimmer The DESMI-TARANTULA skimmer is equipped with a lifting eye for transportation of

the assembled skimmer or for transportation of the pump section alone (see drawing no. 481741/43).

CAUTION! Do not lift the skimmer in other parts than the lifting device or the carrying handles!

Weight: Total: 550 kg 2.2 Mounting (See drawing 481741/43) A. Remove from the container (OPTION) the pump section incl. hopper with weir

lip and the four float pipes with the floats and the two thrusters.

B. Snap on the float pipes with the floats to the pump section and be sure that the pipes are locked.

C. Be sure that the drain hoses from the two DOP-250 pumps are connected to

the drain couplings behind the coupling manifold .

WARNING! Always keep a safety distance to the skimmer/pump of minimum 2 m/7 ft. when the skimmer/pump is connected to the hydraulic power supply. Do not connect the hydraulic hoses to the power supply until you are ready for operation.

3.0 RESPONSE TACTICS 3.1. General remarks It is very difficult to generalise when discussing oil spill situations. Each spill has its

own set of characteristics: Location, close to shore or far off shore, environmental sensitivity, shallow or deep water, waves, current, wind speed and direction, temperature, size of spill, type of oil, time after spill, debris, etc.

However, there are common factors that influence how successful the clean-up

operation will be, and they should all be incorporated in an appropriate contingency plan:

Availability and capability of equipment (ships, skimmer systems, booms, pumps,

storage tanks etc.) and maintenance of the same Availability of manpower, well trained/not trained What to protect first of all Communication Information Surveillance Command Strategy/planning Etc.

Regarding the equipment described in this manual, the most important common

factors for success are:

Maintenance and Training

NOTE! Training again and again is the only way to be sure to realise the full capacity of your DESMI-TARANTULA skimmer system. It is also critical to ensure proper preventative and corrective maintenance as described in this manual.

3.2. Oil spills at sea An overflow weir skimmer should always be within sight of the operator. The closer

the operator is to the skimmer, the better the control and recovery efficiency.

For best manoeuvrability use the skimmer(s) in a single or double sweep configuration with the skimmer(s) in the apex of the ship’s side sweep boom(s). For larger oil spills the configuration may be combined with “J” sweep(s) (Fig. 3) which will feed oil into the system from a wider area. Use for instance towable storage bladders for storage.

As the ship moves forward through the water, the side

sweeping booms concentrate the oil as the surface area within the sweep is reduced. This naturally increases the thickness of the oil layer. It is important that the ship maintains a constant speed of approximately 0.75 knots with most boom systems.

Move through the slick and allow the oil layer to build up

in the apex of the boom before starting the skimmer pump. We recommend an oil layer of at least 2 cm (3/4”) or more for best efficiency.

Try to minimise the total time that the oil is within the

collection area before being skimmed in order to reduce the risk of oil escaping under the boom. If in doubt, it is always better to start skimming too early than too late. Any excess water is not a serious problem since the DOP-250 skimmer pumps do not emulsify the oil and water. The free water can easily be decanted from the storage tank or collapsible barge and pumped out in front of the collection sweep.

Debris is a universal problem in almost all oil spill situations. However, the cutting

knife on the inlet of the DESMI DOP-250 pumps will handle a lot of the debris normally found at a spill site: Seaweed, kelp, plastic bags, aluminium cans, bottles, dead birds, rope (up to 1/2”), wood (up to 1” pine dowel), etc.

Larger debris, such a lumber, tree trunks, large branches, dead animals, etc. must be

manhandled in most situations. One way is to pull it away from the skimmer after it enters the sweep. The best way is to deflect the bigger debris before it enters the containment boom. Various techniques exist such as having personnel located in a boat in front of the sweep, using rakes to pull away the debris.

Deflecting debris may cause deflection of some oil as well. This is, however, far

better than loosing all the oil contained in the boom due to damage or other complications caused by, for instance, a large tree branch.

Wind direction

Fig. 3 - J-configuration

WIND DIRECTION

4.0 OPERATION OF THE DESMI-TARANTULA WEIR SKIMMER

WARNING! WHEN OPERATING: A safety distance to the skimmer/pump of minimum 2 m/7 ft. must be observed by all personnel when the skimmer/pump is connected to the hydraulic power supply. Also when the skimmer/pump is not running.

4.1 Operation principle (see drawing no. 481741/43) The DESMI-TARANTULA is an overflow weir type skimmer. It consists of the pump

section, the four floats with connecting tubes and the hopper with the weir lip. The weir lip consists of a membrane with a ring-shaped float floating inside the hopper.

On land the ring float on the weir lip will be in its lowest position due to the empty

hopper. When the skimmer is being deployed the oil starts flowing over the weir lip and into the hopper. The ring float will begin floating on the oil in the hopper. The buoyancy will lift up the ring float, until the oil stops entering the hopper.

As soon as the pumps start pumping (causing a lower oil level in the hopper), the ring

will automatically adjust its vertical position downwards, allowing more oil to enter the hopper.

At low pump RPM the ring float will float high inside the hopper, allowing only little oil

to enter the skimmer. At higher RPM the pumps will remove the oil under the ring float, the float will thus obtain a lower position and more oil will enter the skimmer. The weir lip will automatically adjust its weir lip to the most optimal position at any recovery rate.

Besides the up/down movement the weir lip is able to float independently of the

skimmer due to its extremely low inertia mass, and the very flexible connection to the skimmer. This enables the ring float to keep its weir lip parallel to the oil/water interface even in small swells which the skimmer is not able to follow.

4.2 Before operation

WARNING ! Keep away from the rotating pump screw and cutting knife. The pump screw/cutting knives are designed for cutting debris normally found at oil spill sites and will also cut off fingers and other limbs.

WARNING ! Always keep a safety distance to the pump of minimum 2 m/7 ft. when the pump is connected to the hydraulic power supply. Do not connect the hydraulic hoses to the power supply until you are ready for operation.

A. Operate the hydraulic power supply of the skimmer according to the operator’s

manual delivered by the supplier of the hydraulic power source. B. Hose connections 1. Connect the hydraulic hose set from power source to the remote control box.

Connect the 10 m hydraulic hose set from the remote control box to the hydraulic manifold on the hose reel.

2. Connect the hydraulic hoses from the hose reel to the quick couplings on the

manifold on skimmer. 3. Connect the discharge hose to the skimmer discharge flange. 4. Check that the locking devices on the hydraulic quick couplings are locked. 5. The hydraulic drain line must always be used. 6. Operate the skimmer pumps DOP1 and DOP2 forward and reverse at low rpm

to check rotation and that the pumps are working properly. 7. Operate the thrusters forward and reverse to check that the thrusters are

working properly. 8. Launch the skimmer by means of the crane 9. When deployed release the skimmer from the crane. 10. After deployment of the skimmer and hoses connect the discharge hose to oil

recovery tank.

CAUTION! The pump should never run dry for more than a few seconds. Observe the safety distance of 2 m/7 ft.!

4.3 Operation

WARNING ! A safety distance to the skimmer/pump of minimum 2 m/7 ft. must be observed by all personnel when the skimmer/pump is connected to the hydraulic power supply. Also when the skimmer/pump is not running.

NOTE! When pumping non-oily media (e.g. water during a training session), grease the plate wheel bearings every 8 hours of operation, using the grease nipple on the plate wheel shaft of the DOP-250 pumps.

A. Place the skimmer by using the thrusters in the apex

of the boom. The best recovery rate and efficiency are obtained

when the skimmer is used in conjunction with an oil boom equipped with a U or V pocket at the apex (Fig. 5). This enables the boom to concentrate even minor oil spills thus getting a thicker oil layer and more efficient skimming. Do not start the skimmer pump before a sufficient oil layer has been collected. DESMI recommends an oil layer of at least 2 cm (3/4”) or more for the best efficiency.

B. As soon as the oil layer has reached a minimum of 2

cm (3/4”) start the skimmer pump at low speed and increase pump speed gradually while monitoring the oil coming out of the discharge hose. Increase pump speed until too much water is coming with the oil out of the discharge hose, then decrease a little.

If it is not possible to monitor the discharge hose adjust the pump speed so that

the collected oil layer in the apex of the boom stays over 2 cm (3/4”). C. If the skimmer pump stops due to excessive debris/solids, simply reverse the

pump to expel the blockage. Then restart the skimming operation.

WARNING ! If it is necessary to remove debris from the skimmer by hand, stop the skimming operation and disconnect the hydraulic hoses at the hydraulic power supply. For safety reasons always keep a distance to the skimmer of min. 2 m/7 ft. when the skimmer is connected to the hydraulic power supply.

Fig. 5 - U-formation with V-apex

Off-loading with the DOP-250 skimmer pump dismantled from the floats is described in the DOP Pump manual.

4.4 Recovery after operation

WARNING ! Always keep a safety distance to the pump of minimum 2 m/7 ft. when the pump is connected to the hydraulic power supply.

CAUTION ! Take care that the discharge hose is not being sucked into the pump as this will result in severe damage to the hose.

A. The contents of the discharge hose may be evacuated by reversing one of the

skimmer pumps at low rpm. B. Start the recovery of the skimmer by reversing the hose reel. If necessary use the

thrusters to place the skimmer in optimal position for recovery. C. If there is still any contents in the discharge hose while rewinding evacuate by

reversing one of the skimmer pumps at low rpm. D. When the skimmer is in position close to the crane lift the skimmer from the water

and on board the vessel. E. Follow the instructions in section 5.

5.0 INSPECTION AFTER OPERATION AND PREVENTATIVE MAINTENANCE

NOTE ! See DOP Pump manual for preventative and corrective maintenance.

5.1. Clean the DESMI-TARANTULA skimmer

WARNING ! Keep away from the rotating pump screw and cutting knives. The pump screw/cutting knives are designed for cutting debris normally found at oil spill sites and will also cut off fingers and other limbs. Always keep a safety distance to the pump of minimum 2 m/7 ft. when the pump is connected to the hydraulic power supply.

A. After the skimmer has been recovered connect the hydraulic hoses to the power

supply and empty the DOP-250 pumps of oil and water. Disconnect the hydraulic hoses again and clean the complete skimmer with a solvent consistent with the medium skimmed.

CAUTION ! Do not use caustic cleaning solutions as this may damage aluminium parts.

B. Wash the skimmer and thrusters with FRESH water. Connect the hydraulic hoses

to the power supply and flush the DOP-250 pumps with fresh water letting the pump run slowly.

C. Disconnect the hydraulic hoses and clean carefully all hydraulic quick couplings

as well as the discharge coupling. Check for leaks and tighten up if necessary. 5.2 Inspection of the DOP-250 pump A. Snap off the float pipes with the floats from the pump section by pulling the eyes

on the locking devices. B. Disconnect the hydraulic hoses incl. quick couplings from the manifold on

skimmer foot. Dismantle the skimmer foot and unscrew the hopper part from the pumps. The pumps are now ready for inspection after operation according to the pump manual.

5.3 Protection of the DESMI-TARANTULA skimmer A. After inspection of the pumps: Reassemble the pumps on the hopper flange and

mount the foot on the pumps. B. Lubricate all quick couplings using anti-corrosion oil and fit the dust caps and

dust plugs on all couplings. C. Store the skimmer in a dry place free of dust. The skimmer should be wrapped in

plastic or by other means protected from a dusty environment when not in use. D. Protect the skimmer against sunlight. The bellows on the weir lip may be

damaged after long time exposure to sunlight. 5.4. Preventative maintenance of DESMI-TARANTULA floatation system A. Very little effort is necessary to keep the floatation system in the necessary state

of readiness that is required for all oil spill recovery equipment. Follow the directions given in Section 5.1.

B. Inspect all surfaces for possible damage due to collision with for instance the

recovery vessel. Check the floats and float tubes for leaks. (Water in the float or tube will indicate a leak). The floats are made of oil resistant polyethylene plastic which is almost shockproof, but nevertheless damage is possible. If a leak is detected contact your local RO-CLEAN DESMI representative for repair.

C. Check the O-sealing rings in the hydraulic quick couplings. Replace them if they

look worn out. Keep the couplings clean. Dirt may affect the functioning of the couplings and the hydraulic system. Always use dust caps and dust plugs.

D. Check the lifting device. It must be safely secured to the hopper. E. Check the locking devices that lock the float pipes to the pump. F. Check that the bellows on the weir lip is in good condition. Protect the weir lip

against sunlight during storage.

6.0 TROUBLESHOOTING

NOTE ! For troubleshooting of the pump refer to the pump manual section 6.0.

Problem The weir lip will not adjust properly

Probable cause Water too shallow

Action Move to deeper water, or if on the shore line: Dig a hole under the skimmer

Viscosity of oil is extremely high and oil layer is very thick

Dismantle the DOP-250 pump from the floats and use it fully submerged

The skimmer recover too much water

Too small oil layer Stop skimming. Collect and concentrate more oil in the apex of the boom before restarting

Pumping is too fast compared to the available amount of oil

Slow down pump RPM, see just above. Check for leaks in the WLA

Use the thrusters to secure the most effective recovery position in the floating containment boom

Oil will not flow into the hopper

Debris prevents the oil from entering the hopper

Clear away debris

The oil is very waxy. Behaves like ice flakes

Help feeding the skimmer using rakes etc. and concentrate more oil for the skimmer to work in

7.0 TECHNICAL SPECIFICATIONS FOR DESMI SKIMMER TYPE DESMI-TARANTULA

Dimensions: Length: Width: Height:

2950 mm 2950 mm 1690 mm

Draft:

850 mm

Weight (dry): 550 kg

Skimmer pump: 2 pcs. DOP-250 vertical positive displacement Archimedes’ screw type. For details see DOP-250 pump manual

Max. recovery rate: 250 m3/h at 1 bar

Max. pressure: 10 bar

Materials: DOP-250 pump: See DOP-250 pump manual

Floats, hopper and floating collar:

Oil resistant polyethylene plastic (PE-HD)

Bellows: Chemically resistant PVC

Float pipes: Stainless steel

Other parts: Stainless steel and seawater resistant aluminium

Coating: Pump: Primer/company paint

7.1 Parts list 682575 for Tarantula Drawing Number 481741 Pos. Item No. Description Qty. 01 681473 DESMI DOP/250 - Dual pump 2 02 184095 Foot 1 05 183771 Floating pipe 4 06 184135 Spacer 4 07 184620 Adapter flange 1 08 681987 Hopper 1 09 181688 Bellows 1 10 181844 Fastening rail 12 11 181848 Ring for bellows 2 12 181670 Inlet float ring 1 13 183769 Float 4 14 183629 Top cover for float 4 15 183576 Discharge manifold 1 16 681984 Lifting device 1 19 181946 6“ discharge flange 1 20 703732 CH-screw M8x 25 A4 16 20 704066 Washer M8 A4 16 21 184622 Coupling panel 1 22 183869 Distance pipe 8 22 183870 Protection grid 2 22 704066 Washer M8 8 22 705255 Hex screw M8x 35 A4 8 23 703376 Hex screw M16x 50 A4 6 23 704033 Washer M16 12 23 710380 Locking Nut M16 6 27 704012 Washer M10 8 28 703232 Locking Nut M12 2 28 704067 Washer M12 4 28 705257 Hex screw M12x 45 A4 2 29 182258 Pin ø10x50 8 30 712392 Locking pin 8 32 703232 Locking Nut M12 4 32 704067 Washer M12 8 32 705257 Hex screw M12x 45 A4 4 33 704033 Washer M16 24 33 708676 Hex screw M16x 65 A4 12 33 710380 Locking Nut M16 12 41 184360 Gasket for hopper 1 42 183867 Gasket for DOP-250 pump 2 44 705184 Dust plug 1” TEMA 2 44 711365 Quick coupling 1" TEMA female 2

Pos. Item No. Description Qty. 44 705455 Dust cap 1” TEMA 2 44 711430 Bonded seal 1" 4 47 713468 Ball valve 1 48 708139 Plug 3/8” 2 55 183874 Coupling adapter 1 56 711357 Quick coupling 3/8” TEMA male 1 56 711356 Quick coupling 3/8” TEMA female 2 56 703619 Dust cap 3/8” TEMA 1 56 711439 Bonded seal 3/8" 1 59 711871 Hydr.hose 3/8” length 550mm 1 62 703330 Nipple 3/8” BSP 3 63 704389 Washer M6 84 63 706893 Locking Nut M6 84 63 708996 BH-screw M6 x 2 A4 84 68 710611 Rubber fender 5m 80 181348 Bulk head 1” x ¾” 4 80 705989 Counter nut ¾” BSP 4 94 705187 Bulk head 3/8” 1 104 703641 Nipple 3/4” BSP 4 108 703330 Nipple 3/8” BSP 4 109 703331 Socket 3/8” BSP 2 110 705113 Check valve 5 bar 1 111 705115 Fitting GE12LR-1/4” 1 117 703636 Bonded seal 3/4" 4 120 703650 Bonded seal 3/8" 2 121 703637 Bonded seal 1” 4 124 706434 Drain pipe ø12x1 1

7.2 Parts list 682580 for Tarantula with thrusters Drawing Number 481743 Pos. Item No. Description Qty. 01 681473 DESMI DOP/250 - Dual pump 2 02 184095 Foot 1 05 183771 Floating pipe 4 06 184135 Spacer 4 07 184620 Adapter flange 1 08 681987 Hopper 1 09 181688 Bellows 1 10 181844 Fastening rail 12 11 181848 Ring for bellows 2 12 181670 Inlet float ring 1 13 183769 Float 4 14 183629 Top cover for float 4 15 183576 Discharge manifold 1 16 681984 Lifting device 1 19 181946 6“ discharge flange 1 20 703732 CH-screw M8x 25 A4 16 20 704066 Washer M8 A4 16 21 184622 Coupling panel 1 22 183869 Distance pipe 8 22 183870 Protection grid 2 22 704066 Washer M8 8 22 705255 Hex screw M8x 35 A4 8 23 703376 Hex screw M16x 50 A4 6 23 704033 Washer M16 12 23 710380 Locking Nut M16 6 27 704033 Washer M16 4 27 760225 Hex screw M16x 35 A4 4 28 703232 Locking Nut M12 2 28 704067 Washer M12 4 28 705257 Hex screw M12x 45 A4 2 29 182258 Pin ø10x50 8 30 712392 Locking pin 8 31 682178 Thrusters 2 32 703232 Locking Nut M12 4 32 704067 Washer M12 8 32 705257 Hex screw M12x 45 A4 4 33 704033 Washer M16 24 33 708676 Hex screw M16x 65 A4 12 33 710380 Locking Nut M16 12 40 711356 Quick coupling 3/8” TEMA female 2 41 184360 Gasket for hopper 1

Pos. Item No. Description Qty. 42 183867 Gasket for DOP-250 pump 2 44 705184 Dust plug 1” TEMA 2 44 711365 Quick coupling 1" TEMA female 2 44 705455 Dust cap 1” TEMA 2 44 711430 Bonded seal 1" 4 47 713468 Ball valve 1 48 708139 Plug 3/8” 2 55 183874 Coupling adapter 1 46 711366 Quick coupling 1” TEMA male 2 56 711357 Quick coupling 3/8” TEMA male 1 56 711356 Quick coupling 3/8” TEMA female 2 56 703619 Dust cap 3/8” TEMA 1 56 711439 Bonded seal 3/8" 1 62 703330 Nipple 3/8” BSP 3 63 704389 Washer M6 84 63 706893 Locking Nut M6 84 63 708996 BH-screw M6 x 2 A4 84 68 710611 Rubber fender 5m 80 181348 Bulk head 1” x ¾” 4 80 705989 Counter nut ¾” BSP 4 94 705187 Bulk head 3/8” 1 104 703641 Nipple 3/4” BSP 4 108 703330 Nipple 3/8” BSP 4 109 703331 Socket 3/8” BSP 2 110 705113 Check valve 5 bar 1 111 705115 Fitting GE12LR-1/4” 1 117 703636 Bonded seal 3/4" 4 120 703650 Bonded seal 3/8" 2 121 703637 Bonded seal 1” 4 124 706434 Drain pipe ø12x1 1

8.0 DRAWINGS 8.1 Assembling, mounting and transportation no. 481741 8.2 Assembling, mounting and transportation no. 481743

9.0 THRUSTERS - Part No. 682178 Pos. Nos. refer to Drawing No. 481577 Pos. No. PART No. DESCRIPTION QTY. 01 712147 Propeller ø185 2 02 712146 Hydraulic motor 2 03 183340 Shaft 2 04 183720 Thruster tube 2 05 183722 Rail 2 06 183337 Screen 1 2 07 183338 Screen 2 2 09 182258 Pin ø10x50 2 10 712392 Locking pin 2 11 700835 Sealing ring 2 12 711341 O-ring 2 13 704394 Chain 0,4m 14 706070 Shackle 4 15 1833480 Pointed screw M5 x 6 4 16 1852620 CH-screw M5 x 12 A4 2 17 704367 CH-screw M8 x 20 A4 8 17 705450 Self-locking nut M8 8 18 1848097 CH-screw M6 x 35 A4 6 19 704389 Washer M6 16 19 705002 CH-screw M6 x 12 A4 16 20 711355 Hydr. Coupling ½” Tema male 2 20 711354 Hydr. Coupling ½” Tema female 2 20 708034 Dust cap ½” 2 20 706477 Dust plug ½” 2 20 711428 Bonded seal ½” 4 21 711357 Hydr. Coupling 3/8” Tema male 2 21 713619 Dust cap 3/8” 2 21 711439 Bonded seal 3/8” 2 27 706185 Nipple 1/8 x ¼” BSP 2 28 703330 Nipple 3/8” BSP 7 29 703650 Bonded seal 3/8” 7 30 183790 Bracket 2 31 703135 Self-locking nut M10 2 31 704003 Washer M10 4 31 705258 Hex.screw M10 x 35 A4 2 32 704390 Plug ¼” BSP 2