Tutorial Cards Mastercam
-
Upload
sepehr-zomorodi -
Category
Documents
-
view
239 -
download
0
Transcript of Tutorial Cards Mastercam
-
7/23/2019 Tutorial Cards Mastercam
1/34
Unearthing the secrets of:Mastercam
Mastercam: a beginners guide
click Start
find Mastercam X5
-
7/23/2019 Tutorial Cards Mastercam
2/34
learning the interface1.
-
7/23/2019 Tutorial Cards Mastercam
3/34
new
ope
save
preview export G code
toggle toolpath visibility
right click --> new toolpath
learning the interface pt. 22.
-
7/23/2019 Tutorial Cards Mastercam
4/34
identify the types of toolpaths you will need3.
-
7/23/2019 Tutorial Cards Mastercam
5/34
initial setup4.
fileopen
file type: all files
-
7/23/2019 Tutorial Cards Mastercam
6/34
Surface Rough pass3.
right click next to the red arrowhere. Then select router toolpaths--> surface rough --> parallel
Surface Rou
a tool pass that surface finish, amaterials like w
-
7/23/2019 Tutorial Cards Mastercam
7/34
Surface Rough_24.
pre
after you select your surface this pops up:
this wthe s
-
7/23/2019 Tutorial Cards Mastercam
8/34
Surface Rough_35.
click select library tool to choose your tool.
-
7/23/2019 Tutorial Cards Mastercam
9/34
Surface Rough_45.
Feed Rate:How fas
Plunge Rate:shoulmill goes into your
Retract Rate:shou
end mill moves out
change your feed raHere are a few base
Corian: 150, 75, 75Wood: 200, 100, 10Foam: 400, 200, 20
-
7/23/2019 Tutorial Cards Mastercam
10/34
Surface Rough_56.
click through the nCheck the boxes ne
the Absolute circ
Absolute means thmatter what, instea
Clearance:How hibe at least .25 ab
Retract:How high
Feed Plane:How hsame as Clearance
-
7/23/2019 Tutorial Cards Mastercam
11/34
Surface Rough_67.
Click through to t
change the stepois .25 since in thmoves over everysurface.
Change the cuttinalong cut - this e
You can change t
Change stepdow
press OK and wa
-
7/23/2019 Tutorial Cards Mastercam
12/34
Surface Finish8.
Surface Finish:
A smooth pass of through on hard mate
a 1/4 or a 3/8 end
-
7/23/2019 Tutorial Cards Mastercam
13/34
Click
Chec
Selec
Makethe s
Surface Finish_29.
*
*
**
-
7/23/2019 Tutorial Cards Mastercam
14/34
Surface Finish_29.
Change thdiameter.my stepovmake a sm
Make sure
You can cthe end mhelpful if y
-
7/23/2019 Tutorial Cards Mastercam
15/34
Pocket10.
Pocket Cut:
An interior recess thatis cut into the surfaceof a workpiece.Pockets may be roundor rectangular.
Right click next to the red arrow in theworkspace, select Router Toolpathsand then Pocket
-
7/23/2019 Tutorial Cards Mastercam
16/34
Pocket_211.
You can select pockets by clicking oneach one with this button
This one allows you to make a boxaround all of them. This is particularlyhelpful if you have a bajillion pocketsyou want to make.
Press ok, and this box will come up.You will go through all of the tabs fromTool to Linking Parameters.
Select appropriate library tool andchange feed/plunge/retract rate like
before
-
7/23/2019 Tutorial Cards Mastercam
17/34
Change roll cutter aroundcorners from Sharp to None
Pocket_312.
-
7/23/2019 Tutorial Cards Mastercam
18/34
Pocket_313.
Entry motion is automatically on helix.Unless you need it specifically, change itto off
-
7/23/2019 Tutorial Cards Mastercam
19/34
Pocket_414.
turn off lead in / out
Under lin
-
7/23/2019 Tutorial Cards Mastercam
20/34
Pocket_515.
Under linall the bu
Make suabove yo
Change y
Change t
Howeverinto the s-.1 (tha
press the
-
7/23/2019 Tutorial Cards Mastercam
21/34
Drill16.
-
7/23/2019 Tutorial Cards Mastercam
22/34
Drill_217.
Select the tool you want to use. This will be
the hole diameter that you drill. Then assigna feed/plunge/ and retract rate.
-
7/23/2019 Tutorial Cards Mastercam
23/34
Drill_318.
Prcadren
-
7/23/2019 Tutorial Cards Mastercam
24/34
Contour19.
-
7/23/2019 Tutorial Cards Mastercam
25/34
change roll cutter around corners tonone and turn off infinite look ahead
Contour_220.
-
7/23/2019 Tutorial Cards Mastercam
26/34
Turn off Lead In/Out
Contour_321.
-
7/23/2019 Tutorial Cards Mastercam
27/34
Contour_422.
Tabs are very helpfulpieces that arent cutall the way out andhold your piece inplace if it is likely tomove.
Click Tabs andAutomatic.Use 2-4 tabs, TabAll and change tabwidth and thickness.An example is .375and .125
Under Cut Parameters, there is an option for cutte
-
7/23/2019 Tutorial Cards Mastercam
28/34
Contour_523.
, pdetermines whether the end mill cuts on the inside
Because Mastercam randomly chooses which side is left or always look in top view to make sure it is cutting on the corrbe on the outside. Go back to Parameters, Cut parameters, a
inside
To set up your stock (for previewin
-
7/23/2019 Tutorial Cards Mastercam
29/34
Setting up your stock24.
To set up your stock (for previewinStock Setup.
Check the box that says display line of where the computer thinks
Change the X, Y, and Z measureme
router (5) and the Y is the 10 sid
Set the origin, which is in the middand the top of Z.
Example: If my stock is 8x10x2Y: 10 X: 8 Z: 2Stock origin:
X: 4 Y: 5 Z: 2
Your masterpiece should look something like this
-
7/23/2019 Tutorial Cards Mastercam
30/34
Previewing your masterpiece25.
Your masterpiece should look something like this.to view individual toolpaths, click on the toolpath youdont want to see, and click the little wave symbolhere and it will disappear.
To preview toolpaths, click thedown shift, and click the last
have checks in the file near ea
-
7/23/2019 Tutorial Cards Mastercam
31/34
regenerating a toolpath26.
If you see something wrong oparameters of the toolpath to means double click to regen
When you have previewed your file and have made ABS
-
7/23/2019 Tutorial Cards Mastercam
32/34
Exporting your masterpiece27.
When you have previewed your file and have made ABSsure there is no red error showing up in the preview, yoyour file. Make sure all the toolpaths are still highlightednext to them. Press G1.
This box will show up. Un-click Edit, and click Ok. You wwhere you want to export your file. Put it somewhere th
easy to access again. Very important: your file name mters or less, no special characters, and in CAPS.
This box will pop up with an error Enter UAO(1-10) or (This is correct, just press enter.If this does NOT show up,youre doing something wrong.
-
7/23/2019 Tutorial Cards Mastercam
33/34
Opening your NC code28.
Double click on your NC file to oit. You have to tell the computer WordPad to open it.Do NOT open it with word, it wilit as a .docx file and thats not u
to anyone. Here you can previewG-Code, and double check tools
-
7/23/2019 Tutorial Cards Mastercam
34/34
Con
You have
Yay!29.