Triflex · PDF filewith infill of Mandura 1–3 mm Triflex ProPark reinforced with...
Transcript of Triflex · PDF filewith infill of Mandura 1–3 mm Triflex ProPark reinforced with...
Triflex ProPark®
Top deck waterproofing system (OS 10)
Planning documents
ProPark planning documents 07/2012
2 |
Triflex ProPark®
Top deck waterproofing system (OS 10)
Waterproofing for top decks and parking decks over occupied premises must meet high quality standards if they are to be functional in the long-term. In exposed areas in particular, thermal loads and the resulting structural movements must be reliably absorbed. Entrances and exits as well as straight and spiral ramps are also subject to high shear forces due to the high volume of traffic. The use of PMMA throughout ensures that the chemical bond between the layers holds across the entire surface without water infiltration. The system-integrated detail solutions – e.g. for junctions and joints – round off the refurbishment concept to give your structure long-lasting protection against chemical and mechanical loads.Triflex ensures the quality of workmanship on the site by holding periodical basic and advanced training courses with certified specialist companies. This offers you the benefit of having competent contact persons at all stages of the project. 30 years of experience in refurbishment and a wide array of references testify to the durability of Triflex waterproofing and coating solutions. Triflex ProPark was developed specially for car parks with high loads and stresses. The tested system solutions offer reliable protection against external influences. A wide range of colours supports individual creative design.
Safety for heavy duty components
Advantages at a glance ■ Highly resilient with dynamic crack bridging
The system is full-surface fleece-reinforced. This gives the material a level of flexibility that leaves it unaffected by any movement of the foundation.
■ System-integrated detail solutionsThe cured resin forms a seamless and joint-free surface. Even complex details, such as joints, can be easily and homogeneously waterproofed using specially developed detail solutions.
■ Ideal for refurbishmentsThe system is suitable for almost all substrates. With a low surface weight of less than 8 kg/m², it can also be applied on top of asphalt surfaces without negatively affecting stability. This saves removal costs and time.
■ Short closure periodsTriflex ProPark offers much faster curing times than systems made of EP or PUR resins. Complete refurbishment of sensitive areas such as entrances and exits is possible in a single day thanks to the optimised application time. This safeguards income and reduces closure times and disruptions to traffic. Parking spaces are soon ready for use again.
■ Long-lasting protectionThe Triflex ProPark system withstands high mechanical loads, which extends refurbishment intervals by years. Maintenance costs are reduced to a minimum. The surfacing solution Triflex Cryl M 264 meets the strictest requirements of the German Federal Highway Research Institute (BASt) – Traffic Class P7 to DIN EN 13197. This classification is based on a wear test of 4 million cycles.
■ ColoursThe surface is available in a range of colours. This facilitates recognition and orientation among car park users and improves traffic safety.
■ Tested safetyTriflex ProPark has obtained a Class OS 10 General Building Supervisory Authority Test Certificate (abP) acc. to Building Regulations List A, Part 2, No. 2.24.
Applications
Triflex ProPark is a full-surface reinforced waterproofing system used on exposed parking decks and top decks. This system withstands high mechanical loads and is made of fast-curing polymethyl methacrylate (PMMA) resin. It was developed specially for multi-storey car park traffic and reliably protects the structure long-term. The top deck waterproofing system Triflex ProPark has obtained a General Building Supervisory Authority Test Certificate (abP) and is classified to OS 10.
ProPark planning documents 07/2012
| 3
Triflex ProPark®
Top deck waterproofing system (OS 10)
System description
■ Full-surface reinforced waterproofing system based entirely on polymethyl methacrylate (PMMA) ■ Withstands high mechanical loads ■ Shear-resistant design ■ Seamless ■ System-integrated detail solutions ■ Full-surface adhesion and impermeable ■ Resilient ■ Enhanced dynamic crack-bridging, Class 4.2 (-20 °C)
■ Cold-applied ■ Fast-curing ■ Ready for vehicle traffic after approx. 3 hours ■ Chemical-resistant ■ Weather-resistant (UV, IR, etc.) ■ Non-slip ■ Variety of colours available ■ Class OS 10 General Building Supervisory Authority Test Certificate acc. to Building Regulations List A, Part 2, No. 2.24
Properties
System variants
System design
System components
Triflex Cryl Finish 209Triflex Cryl M 264
Triflex Cryl Finish 202
Triflex DeckFloorwith infill of quartz sand 0.7–1.2 mm
Triflex DeckFloorwith infill of Mandura 1–3 mm
Triflex ProParkreinforced with Triflex Special Fleece
Triflex Cryl Primer 287 – for absorbent substrates or Triflex Cryl Primer 222 – for asphalt substrates
Variant 1Surfaces with standard loads
and stresses; e.g. parking spaces
Variant 2Surfaces with high loads
and stresses; e.g. entrances and exits, straight and spiral ramps, lanes
Variant 3Surfaces with high loads
and stresses and high grip requirements; e.g. steep ramps
Wearing layer
Waterproofing
Primer
Substrate
Wearing layer
Waterproofing
Primer
Varaint 1 Varaint 2 Varaint 3
ProPark planning documents 07/2012
4 |
Triflex ProPark®
Top deck waterproofing system (OS 10)
Substrate repairing
Triflex Cryl RS 240 Mortar for repairing mineral substrates with roughness depths of RT > 10 mm. Volume at least 2.20 kg/m² per mm layer thickness.
Triflex Cryl RS 242 Mortar for repairing bituminous substrates with roughness depths of RT > 10 mm. Volume at least 2.20 kg/m² per mm layer thickness.
Triflex DeckFloor Levelling paste for repairing mineral or bituminous substrates with roughness depths of RT 1–10 mm with the addition of up to 20.00 kg quartz sand 0.7–1.2 mm* per 33 kg Triflex DeckFloor.Volume at least 2.00 kg/m² per mm layer thickness.
Scratch coat for repairing mineral or bituminous substrates with roughness depths of RT 0.5–1 mm with the addition of up to 10.00 kg quartz sand 0.2-0.6 mm* per 33 kg Triflex DeckFloor.Volume: at least 2.00 kg/m² per mm layer thickness.
Priming
Triflex Cryl Primer 287Pour on thickly and spread evenly using a cellular rubber spreader. Then cross-coat using a Triflex universal roller.Volume: at least 0.35 kg/m².Can be recoated after approx. 45 min.
Triflex Cryl Primer 222Apply evenly with a Triflex universal roller.Volume: at least 0.40 kg/m².Can be recoated after approx. 45 min.
Triflex Pox R 100Pour on thickly and spread evenly using a cellular rubber spreader. Then cross-coat using a Triflex universal roller and immediately sandblast with a surplus of quartz sand.Volume of Triflex Pox R 100: at least 0.30 kg/m², Volume of quartz sand 0.2–0.6 mm: at least 2.00 kg/m².Can be recoated after approx. 12 hrs.
Triflex Than Primer 532Apply evenly with a Triflex universal roller.Volume: approx. 40–80 g/m². Can be recoated after approx. 12 hrs.
Substrate Pretreatment PrimingAluminium* Abrade with Triflex Cleaner, roughen surface No primerAsphalt Grinding, milling or dust-free shot-blasting Triflex Cryl Primer 222Composite thermal insulation systems* Triflex Pox R 100Concrete Grinding, milling or dust-free shot-blasting Triflex Cryl Primer 287Copper* Abrade with Triflex Cleaner, roughen surface No primerEpoxy resin coating Roughen surface, adhesion and compatibility test No primer Glass* Abrade with Triflex Cleaner, roughen surface, adhesion test Triflex Than Primer 532Lightweight concrete* Triflex Cryl Primer 287Mortar, resin-modified Grinding, milling or dust-free shot-blasting; adhesion and compatibility test Triflex Pox R 100Paints Grinding or milling, completely remove See substratePlaster/masonry* Triflex Cryl Primer 287PU coating Roughen surface, adhesion and compatibility test No primerPVC mouldings, rigid* Abrade with Triflex Cleaner, roughen surface No primerScreeds Grinding, milling or dust-free shot-blasting Triflex Cryl Primer 287Stainless steel* Abrade with Triflex Cleaner, roughen surface No primerSteel, galvanized* Abrade with Triflex Cleaner, roughen surface No primerTiles Mechanically remove glaze Triflex Cryl Primer 287Wood* Remove paints Triflex Cryl Primer 287Zinc* Abrade with Triflex Cleaner, roughen surface No primer
Substrate pretreatment
* Only areas not subject to high mechanical stress, e.g., details and flashing. Information on other substrates is available on request.
System description
Dew point: During application, the surface temperature must be at least 3 °C above the dew point temperature. Below this temperature, a separating film of moisture can form on the surface.Hardness: Mineral substrates must be permitted to fully harden for at least 28 days.Adhesion: The following minimum tensile adhesion strengths must be met on pre-treated test areas: Concrete 1.5 N/mm².
Substrate suitability should always be checked on a case by case basis. The substrate must be clean, dry and free of cement bloom, dust, oil, grease and other adhesion-reducing dirt.Moisture: When carrying out application work, the substrate moisture must not exceed 6% by weight. Ensure that structural measures are taken to prevent moisture penetration of the coating from underneath.
* The quartz sand grading curve must be adjusted on-site, if necessary
Substrate
ProPark planning documents 07/2012
| 5
Triflex ProPark®
Top deck waterproofing system (OS 10)
Detail waterproofing
All junctions, transitions and other detail solutions must be completed before the surface waterproofing is applied.Points 1 to 3 are completed wet-on-wet.1. Triflex ProDetail
Apply evenly with a radiator roller. Volume: at least 2.00 kg/m².
2. Triflex Special FleeceLay strips, removing any air bubbles. Overlap the fleece strips by at least 5 cm.
3. Triflex ProDetailApply until the Triflex Special Fleece is fully saturated. Volume: at least 1.00 kg/m².
Total volume of Triflex ProDetail: at least 3.00 kg/m².Can be recoated after approx. 45 min.4. Triflex Cryl Finish 209
Cross-coat evenly using a Triflex universal roller. Volume: at least 0.50 kg/m².
Can be recoated after approx. 1 hr.For dimensions, see Triflex ProPark system drawings.
Joint waterproofing
All joints must be waterproofed before surface waterproofing. To prevent abutting edges, joints should always be embedded in the substrate (see system drawings).
Construction joint:
1. Triflex Cryl RS 240Level joint flush with surface (if necessary).
Points 2 to 4 are completed wet-on-wet.2. Triflex ProDetail
Apply a width of 16 cm with a radiator roller. Volume: at least 0.30 kg/m.
3. Triflex Special FleeceInsert a 15 cm wide strip, removing any air bubbles. Overlap the ends of the fleece by at least 5 cm.
4. Triflex ProDetailApply until the Triflex Special Fleece is fully saturated. Volume: at least 0.30 kg/m.
Total volume of Triflex ProDetail: at least 0.60 kg/m.Can be recoated after approx. 45 min. 5. Triflex Cryl Finish 209
Apply a width of approx. 10 cm with a Triflex universal roller above the construction joint. Volume: at least 0.50 kg/m².
Can be recoated after approx. 1 hr.For dimensions, see Triflex ProPark system drawings.
Important note:Horizontal details can also be waterproofed with Triflex ProPark.
Settlement joint:
Joints subject to normal mechanical stress.1. Triflex Cryl Paste
Apply a width of approx. 4 cm to both sides of the joint to bond the Triflex Support Strip.
2. Triflex Support StripLay in the joint as a loop. Can be recoated after approx. 1 hr.
Points 3 to 7 are completed wet-on-wet.3. Triflex ProDetail
Apply to both sides of the joint and on the support strip using a radiator roller. Volume: at least 0.70 kg/m.
4. Triflex Special FleeceLay a 35 cm wide strip as the first loop, making sure there are no air bubbles. Overlap the ends of the fleece by at least 5 cm.
5. Triflex ProDetailApply to completely saturate the Triflex Special Fleece and as a preliminary layer for the next fleece loop. Volume: at least 0.70 kg/m.
6. Triflex Special FleeceLay a 35 cm wide strip as the second loop, making sure there are no air bubbles. Overlap the ends of the fleece by at least 5 cm.
7. Triflex ProDetailApply until the Triflex Special Fleece is fully saturated. Volume: at least 0.70 kg/m.
Total volume of Triflex ProDetail: at least 2.10 kg/m. Can be recoated after approx. 1 hr.After application of the surface waterproofing and the driving surface.8. PE round sealing band
Place in the joint.9. Triflex FlexFiller
Fill the joint so it is flush with the surface. Volume: approx. 2.20 kg/l per mm layer thickness.
Ready for pedestrian and vehicle traffic after approx. 3 hrs.For dimensions, see Triflex ProPark system drawings.
Joints subject to high mechanical stress on request.
Important note:1. The settlement joint is taped off with adhesive tape for the subsequent
layers so that the joint remains permanently omitted. All further layers are only taken to the edge of the joint. Prior to curing the layer, the adhesive tape must be removed and new tape applied for each further layer. On completion of the system build-up, the joint is made flush with the surface using Triflex FlexFiller.
2. The settlement joints are all maintenance joints. It may be necessary to renew the joint sealant after structural movement.
System description
ProPark planning documents 07/2012
6 |
Triflex ProPark®
Top deck waterproofing system (OS 10)
Surface waterproofing
Application is wet-on-wet.1. Triflex ProPark
Apply evenly with a Triflex universal roller. Volume: at least 2.00 kg/m².
2. Triflex Special Fleece Lay without air bubbles. Overlap the strips of fleece by at least 5 cm.
3. Triflex ProParkApply until the Triflex Special Fleece is fully saturated. Volume: at least 1.00 kg/m².
Total volume of Triflex ProPark: at least 3.00 kg/m².Can be recoated after approx. 1 hr.For dimensions, see Triflex ProPark system drawings.
Wearing layer, variant 1
1. Triflex DeckFloor Spread evenly using a trowel and level out using a spiked roller. Volume: at least 3.00 kg/m²
2. Quartz sand, size 0.7–1.2 mm Sandblast the wet wearing layer in excess. Once the coating is cured, remove any surplus. Volume: at least 7.00 kg/m²
Can be recoated after approx. 2 hrs.3. Triflex Cryl Finish 209
Apply transversely to the direction of travel using a hard rubber spreader and cross-coat using a Triflex universal roller. Volume: at least 0.70 kg/m².
Ready for vehicle traffic after approx. 2 hrs.
Wearing layer, variant 2
Preparatory work:
To enable reliable drainage of the surface water, the coating is divided into panels. Vehicle traffic areas are divided into identically sized rectangular panels. The length of the rectangle should be max. twice the width of the traffic path. Ramps are divided into diagonal strips with a max. width of 50 cm. The dividing lines are omitted by taping over with adhesive tape (max. width: 2.5 cm).
Important note:The surface waterproofing is omitted in the area of the settlement joint.
Important notes: The wearing layer is omitted in the area of the settlement joint.The sealing of all vertical junctions, transitions and details must be carried out prior to the surface finishing with thixotropic Triflex Cryl Finish 209. The product is thickened by the addition of 1 wt.-% Triflex Liquid Thixo.
Finishing the omissions in subdivided surfaces:
At the later surface omission, an approx. 10 cm-wide strip of Triflex Cryl Finish 209 must be applied. The chosen colour of Triflex Cryl Finish 209 should be as dark as possible for cleaning reasons.
Triflex Cryl Finish 209 Apply a width of approx. 10 cm to the waterproofing at the surface omission with a Triflex universal roller.Volume: at least 0.50 kg/m².Can be recoated after approx. 1 hr.
Wearing layer:
Triflex Cryl M 264Apply with a stainless steel trowel and spread over the grain tips. Volume: at least 3.00 kg/m². Ready for pedestrian traffic after approx. 1 hr, ready for vehicle traffic after approx. 3 hrs. For dimensions, see Triflex ProPark system drawings.
Wearing layer, variant 3
1. Triflex DeckFloor Spread evenly using a trowel and level out using a spiked roller. Volume: at least 3.00 kg/m²
2. Mandurax, size 1.0–3.0 mm Sandblast the wet wearing layer in excess. Once the coating is cured, remove any surplus. Volume: at least 7.00 kg/m²
Can be recoated after approx. 2 hrs.3. Triflex Cryl Finish 202
Cross-coat using a Triflex universal roller. Volume: at least 0.80 kg/m².
Ready for vehicle traffic after approx. 2 hrs.
Important note: The adhesive tape for subdividing the surface must be removed while the Triflex Cryl M 264 is still wet.Transitions between the surfaces of different system variants must be completed as shown in the Triflex ProPark 1315 system drawing.
Important notes: The wearing layer is omitted in the area of the settlement joint.The sealing of all vertical junctions, transitions and details must be carried out prior to the surface finishing with thixotropic Triflex Cryl Finish 209. The product is thickened by the addition of 1 wt.-% Triflex Liquid Thixo.
System description
ProPark planning documents 07/2012
| 7
Triflex ProPark®
Top deck waterproofing system (OS 10)
System descriptionCollision protection
To protect against mechanical damage, the waterproofing should be protected in risk areas (e.g., kerbs, thresholds and joints) by stainless steel cover plates.
1. Triflex Cleaner Degrease plates and roughen the underside.
2. Triflex Cryl Paste Cover the entire underside of the plate with Triflex Cryl Paste.
3. Cover plateStick into place and remove surplus paste with a trowel, secure mechanically if necessary.
Volume of Triflex Cryl Paste: at least 0.50 kg/m².Can be subject to loads after approx. 45 min.For dimensions, see Triflex ProPark system drawings.
Interruptions during work
If work is interrupted for more than 12 hrs, or if soiled by rain etc., the intersection must be activated with Triflex Cleaner. Airing time at least 20 min. Transitions to subsequent waterproofing must overlap (including Triflex Special Fleece) by a minimum of 10 cm. This also applies to junctions, transitions and detail solutions with Triflex ProDetail. The finish must be applied within 24 hrs. If this application is delayed for any reason, the surface to be finished must be pre-treated with Triflex cleaner.
System components
For information on applications, conditions for use and instructions for mixing, see product information (request if necessary):
Quality standard
All products are manufactured in accordance with the standards defined in ISO 9001. To ensure quality is not compromised, Triflex products are only installed by specialist, fully trained and qualified contractors.
Triflex Cryl Finish 202Triflex Cryl Finish 209Triflex Cryl M 264Triflex Cryl PasteTriflex Cryl Primer 222Triflex Cryl Primer 287Triflex Cryl RS 240Triflex Cryl RS 242Triflex DeckFloor
Triflex FlexFillerTriflex Pox R 100Triflex ProDetailTriflex ProParkTriflex CleanerTriflex Special FleeceTriflex Liquid ThixoTriflex Than Primer 532
Gradient / Evenness
Before commencing any surfacing work and during the work itself, it is essential to ensure the correct gradient and evenness of the substrate. Any corrections required must be taken into account during this work.
Dimensional tolerances
When carrying out surfacing work, always ensure compliance with the permissible tolerances for building construction (DIN 18202, Table 3, line 4).
Safety tips / Accident prevention
Read the safety data sheets before using the products.
Volumes required and waiting times
The specified volumes apply only to smooth, even surfaces. Special allowances must be made for unevenness, roughness and porosity. Information regarding airing and waiting times applies to a substrate at an ambient temperature of +20 °C.
General notes
The basis for the use of Triflex products can be found in the system descriptions, system drawings and product information sheets. It is essential to heed these when planning and carrying out the building project.Departures from the technical information of Triflex GmbH & Co. KG applicable at the time of work can compromise the guarantee. Any project-related departures are subject to the written authorisation of Triflex.All data is based on general regulations, directives and other technical rules. The general regulations applicable in the particular country of use must be respected. Since the parameters can vary from case to case, the user is required to test the suitability, e.g., of the substrate.Non-system substances must not be added to Triflex systems.Subject to change in the interests of technical advancement or enhancement of Triflex products.
Tender texts
Please visit the download section of the Triflex website at www.triflex.com to obtain the current standard specifications for tender, which are available free of charge in a range of different file formats. The Triflex Planning CD "Creative multi-storey car parks" contains details of all our standard systems, complete with texts for tender. Or you can request a copy by sending an e-mail to: [email protected].
ProPark planning documents 07/2012
8 |
Triflex ProPark®
Top deck waterproofing system (OS 10)
System drawings
Surface
Drawing no.: ProPark-1315
Height differences are exaggerated.
Approx. 2.5 cm
Detail A/B/C
Surface subdivision
Drawing no.: ProPark-1316
Approx. 2.5 cm Approx. 2.5 cm
App
rox.
2.5
cm
App
rox.
2.5
cm
Width ≤ 5.50 m
max
. 2 x
wid
th
Surface subdivisions finished with approx. 10 cm-wide strips of Triflex Cryl Finish 209
Ramp surface subdivision
Ramp
Drawing no.: ProPark-1313
Drawing no.: ProPark-1312
Approx. 2.5 cmApprox. 2.5 cm Approx. 2.5 cm
Approx. 2.5 cm Approx. 2.5 cm
App
rox.
2.5
cm
App
rox.
2.5
cm
App
rox.
50
cm
Approx. 50 cm Approx. 50 cm
Surface subdivisions finished with approx. 10 cm-wide strips of Triflex Cryl Finish 209
Detail B
ProPark planning documents 07/2012
| 9
Triflex ProPark®
Top deck waterproofing system (OS 10)
Primer
Substrate
Wearing layer: Triflex DeckFloor with infill of quartz sand 0.7–1.2 mm
Surface waterproofing: Triflex ProPar, reinforced with Triflex Special Fleece
Triflex ProPark system design, variant 1 – Detail A
System drawings
Finish: Triflex Cryl Finish 209
Primer
Substrate
Wearing layer: Triflex DeckFloor with infill of Mandurax 1–3 mm
Surface waterproofing: Triflex ProPark, reinforced with Triflex Special Fleece
Triflex ProPark system design, variant 3 – Detail C
Finish: Triflex Cryl Finish 202
Primer
Substrate
Wearing layer: Triflex Cryl M 264
Surface waterproofing: Triflex ProPark, reinforced with Triflex Special Fleece
Triflex ProPark system design, variant 2 – Detail B
ProPark planning documents 07/2012
10 |
Triflex ProPark®
Top deck waterproofing system (OS 10)
Wall junction Gully/Gutter
min. 5 cm
Detail D/E/F Detail D/E/F
min. 5 cm
min
. 15
cm
Drawing no.: ProPark-1301 Drawing no.: ProPark-1302
min. 5 cm
Height differences are exaggerated.
System drawings
Detail waterproofing finished with Triflex Cryl Finish 209
Settlement joint
Detail D/E/F
min. 5 cm min. 5 cm
min
. 15
cm
Drawing no.: ProPark-1303
Detail waterproofing finished with Triflex Cryl Finish 209
Kerb
min. 5 cm
Drawing no.: ProPark-1304
Cover plate, bonded with Triflex Cryl Paste
Detail D/E/F D/E/F
Detail waterproofing finished with Triflex Cryl Finish 209
min. 5 cm
Detail waterproofing embedded approx. 3 mm in the substrate
ProPark planning documents 07/2012
| 11
Triflex ProPark®
Top deck waterproofing system (OS 10)
System drawings
Primer
Substrate
Wearing layer: Triflex DeckFloor with infill of quartz sand 0.7–1.2 mm
Surface waterproofing: Triflex ProPark, reinforced with Triflex Special Fleece
Triflex ProPark system design, variant 1 – Detail D
Finish: Triflex Cryl Finish 209
Triflex ProPark system design, variant 3 – Detail F
Primer
Substrate
Wearing layer: Triflex Cryl M 264
Surface waterproofing: Triflex ProPark, reinforced with Triflex Special Fleece
Triflex ProPark system design, variant 2 – Detail E
Detail waterproofing: Triflex ProDetail*, reinforced with Triflex Special Fleece
Detail waterproofing: Triflex ProDetail*, reinforced with Triflex Special Fleece
Primer
Substrate
Wearing layer: Triflex DeckFloor with infill of Mandurax 1–3 mm
Surface waterproofing: Triflex ProPark, reinforced with Triflex Special Fleece
Finish: Triflex Cryl Finish 202
Detail waterproofing: Triflex ProDetail*, reinforced with Triflex Special Fleece
Construction joint
Detail D/E/F
min. 15 cm
Drawing no.: ProPark-1310
Detail waterproofing embedded approx. 3 mm in the substrate
* Horizontal details (e.g. construction joints)
can be waterproofed with Triflex ProDetail or Triflex ProPark.
ProPark planning documents 07/2012
12 |
Triflex ProPark®
Top deck waterproofing system (OS 10)
System drawingsSettlement joint wall intersection
Detail G/H/J
*
Triflex Support Strip, bonded in with Triflex Cryl Paste
Round sealing band
Drawing no.: ProPark-1314
* Omission of surface waterproofing and wearing layer (see system description)
min. 10 cmmin. 3 cm
Filled with Triflex FlexFiller
Detail finished with Triflex Cryl Finish 209
min
. 15
cm
Settlement joint surface
*
Drawing no.: ProPark-1311
* Omission of surface waterproofing and wearing layer (see system description)
min. 10 cm min. 10 cm
Detail G/H/J
Round sealing band
Triflex Support Strip, bonded in with Triflex Cryl Paste
min. 3 cm
Filled with Triflex FlexFiller
Height differences are exaggerated.
Joint waterproofing embedded approx. 5 mm in the substrate
Joint waterproofing embedded approx. 5 mm in the substrate
ProPark planning documents 07/2012
| 13
Triflex ProPark®
Top deck waterproofing system (OS 10)
System drawings
Primer
Substrate
Wearing layer: Triflex DeckFloor with infill of quartz sand 0.7–1.2 mm
Surface waterproofing: Triflex ProPark, reinforced with Triflex Special Fleece
Triflex ProPark system design, variant 1 – Detail G
Finish: Triflex Cryl Finish 209
Primer
Substrate
Wearing layer: Triflex Cryl M 264
Surface waterproofing: Triflex ProPark, reinforced with Triflex Special Fleece
Triflex ProPark system design, variant 2 – Detail H
Joint waterproofing: 2nd loop Triflex Special Fleece, saturated with Triflex ProDetail
1st loop Triflex Special Fleece, saturated with Triflex ProDetail
Joint waterproofing: 2nd loop Triflex Special Fleece, saturated with Triflex ProDetail
1st loop Triflex Special Fleece, saturated with Triflex ProDetail
Primer
Substrate
Wearing layer: Triflex DeckFloor with infill of Mandurax 1–3 mm
Surface waterproofing: Triflex ProPark, reinforced with Triflex Special Fleece
Triflex ProPark system design, variant 3 – Detail J
Finish: Triflex Cryl Finish 202
Joint waterproofing: 2nd loop Triflex Special Fleece, saturated with Triflex ProDetail
1st loop Triflex Special Fleece, saturated with Triflex ProDetail
ProPark planning documents 07/2012
14 |
Triflex ProPark®
Top deck waterproofing system (OS 10)
Creative use of colours and surfaces
7031 Blue grey with infill of quartz sand
7030 Stone grey with infill of quartz sand
7032 Pebble grey with infill of quartz sand
7035 Light grey with infill of quartz sand
7037 Dusty grey with infill of quartz sand
7043 Traffic grey with infill of quartz sand 7040 Window grey with infill of quartz sand
1023 Traffic yellow with infill of quartz sand
2009 Traffic orange with infill of quartz sand
3020 Traffic red with infill of quartz sand
4006 Traffic purple with infill of quartz sand
5017 Traffic blue with infill of quartz sand
6024 Traffic green with infill of quartz sand
9010 White with infill of quartz sand
See your finished surface beforehand ...You want to know what your finished multi-storey car park or parking deck is going to look like beforehand? With the online “Triflex Multi-Storey Car Park Studio” programme this can be achieved both simply and quickly. The design software offers a pre-selection of application examples which can be used to provide a first impression of the variety of designs offered by Triflex.
The edited photos can then simply be added to your planning documentation. Give it a try! Further information can be found at www.triflex.com or go directly to www.triflex.com/parkhaus-studio.
Please note: Minor variations between the colours shown here and the actual colours are due to printing technology and the materials used.
ProPark planning documents 07/2012
| 15
Triflex ProPark®
Top deck waterproofing system (OS 10)
Triflex System Solutions
Triflex products are based on more than 30 years of experience, combined with continuous development and liquid applied waterproofing system solutions that have been tried and tested in a whole range of applications.
The company is certified to ISO 9001 and Triflex products have obtained ETA approval or obtained General Building Supervisory Authority Test Certificates (abP) and compliance marks; just some of the factors that contribute to the high standard of quality.
Triflex systems are applied by trained and experienced specialists. All specialist companies that work with Triflex fit the strict requirement profile, to guarantee that the Triflex standards of workmanship and service for the customer are met.
Quality application
The next stepOur aim is to make life that little bit easier for you. We will provide you with all the information you need to reach a clear decision. Our technical support team will be happy to visit you on site.
For detailed Triflex system descriptions, bills of quantities, colour scheme suggestions as well as reference projects, please contact us at the following address or simply visit www.triflex.com.
ISO 14001
002
ProP
ark
plan
ning
doc
umen
ts E
N-A
4-07
/201
2Scan the QR code with your smartphone for instant access to further information.
InternationalTriflex GmbH & Co. KGKarlstrasse 5932423 Minden | GermanyTel. +49 (0)571 [email protected]