Top Side -Report

download Top Side -Report

of 22

Transcript of Top Side -Report

  • 7/27/2019 Top Side -Report

    1/22

    Contents1 Introduction: ............................................................................................................................ 12 Problem Definition: ................................................................................................................. 13 Basic Data: ............................................................................................................................... 1

    3.1 Material Properties: .......................................................................................................... 14 Local Design and Framing Arrangement: ............................................................................... 2

    4.1 Floor Beams: .................................................................................................................... 24.2 Secondary Beam:.............................................................................................................. 3

    5 Computer Model: ..................................................................................................................... 45.1 Assumptions: .................................................................................................................... 45.2 Member Group Plots: ....................................................................................................... 55.3 Member Section Plots: ..................................................................................................... 95.4 Joint Group Plots: ........................................................................................................... 13

    6 Load Simulation: ................................................................................................................... 176.1 Dead Load: ..................................................................................................................... 176.2 Live Load: ...................................................................................................................... 186.3 Wind Load: ..................................................................................................................... 19

    7 Results: .................................................................................................................................. 208 References: ............................................................................................................................ 21

  • 7/27/2019 Top Side -Report

    2/22

    1

    Structural model of the topside

    1 Introduction:The topside structure supports a significant amount of load and it transmits the load to the jacket.

    The loads acting on the topside structure are live loads, wind loads and dead loads. By

    considering these loads we have designed and simulated a topside structure subjected to such

    loads. The entire structure is modeled, analysed and sized using SACS 5.3 Executive Service

    Pack 1 version 5.3.1.1(with API RP-2A & AISC 13th

    Edition guidelines).

    2 Problem Definition:Prepare a structural model of topside structure with the following requirement.

    Cellar Deck = 40 m 30 m EL (+)20 m

    Main Deck = 42 m 34 m EL (+)30 m

    Leg Spacing = 20 m15 m

    Wind Speed = 50 m/s

    Live Load = 10 kN/m2

    Carry out in place analysis and size the members and joints.

    3 Basic Data:3.1 Material Properties:The Material used is Steel and its properties are given below

    Density = 7.849 tonne/m3

    Young's Modulus (E) = 20000 kN/cm2

    Shear Modulus (G) = 8000 kN/cm2

    Yield strength (Fy) = 34.5 kN/cm2

  • 7/27/2019 Top Side -Report

    3/22

    2

    4 Local Design and Framing Arrangement:4.1 Floor Beams:Except that of the primary and secondary Beams all other members in the structures are chosen

    to be tubular sections.

    Figure 1: Boxed Plate Beam used for Primary

    Beam

    Figure 2: Secondary Beam I - Section

  • 7/27/2019 Top Side -Report

    4/22

    3

    4.2 Secondary Beam:The secondary beam of span 9.5m and section UB457B89 is considered.

    The simply supported beam arrangement which takes up a load of 10 kN/m2as transferred by the

    plate of 9.5 m x 1 m is shown in fig. X. It is assumed that secondary Beam takes up to half of the

    load acting on two plates resting on it. Hence total area supported by the secondary Beam will

    be 9.5 sq.m.

    )))

    Deflection of the secondary Beam:

    )))

    Allowable Deflection:

    Figure 3: Cross section chosen for outer secondary Beams

  • 7/27/2019 Top Side -Report

    5/22

    4

    5 Computer Model:5.1 Assumptions:The structure is modeled using the following assumptions

    Global design is followed in the software

    The elements used are isotropic, homogeneous and elastic.

    Figure 4: Isometric view of modeled topside

  • 7/27/2019 Top Side -Report

    6/22

    5

    5.2 Member Group Plots:

    Figure 5: Member Group ID of Plan at elevation (+)10m

    Figure 6: Member Group ID of plan at Elevation (+) 20 m

  • 7/27/2019 Top Side -Report

    7/22

    6

    Figure 7: Member Group ID of plan at Elevation (+) 30 m

  • 7/27/2019 Top Side -Report

    8/22

    7

    Figure 8: Member Group ID at location y= 0 m

    Figure 9: Member Group at location y=15 m

  • 7/27/2019 Top Side -Report

    9/22

    8

    Figure 10: Member Group at location x= 0 m

    Figure 11: Member Group ID at location x=20 m

  • 7/27/2019 Top Side -Report

    10/22

    9

    5.3 Member Section Plots:

    Figure 12: Member Section for plan at elevation (+) 10 m

    Figure 13: Member Section for plan at elevation (+) 20 m

  • 7/27/2019 Top Side -Report

    11/22

    10

    Figure 14: Member Section for plan at elevation (+) 30 m

  • 7/27/2019 Top Side -Report

    12/22

    11

    Figure 15: Member seection at location y = 0 m

    Figure 16: Member seection at location y= 15 m

  • 7/27/2019 Top Side -Report

    13/22

    12

    Figure 17: Member Section at location x= 0 m

    Figure 18: Member Section at location x = 20 m

  • 7/27/2019 Top Side -Report

    14/22

    13

    5.4 Joint Group Plots:

    Figure 19: Joint numbers at location x= 0 m

    Figure 20: Joint numbers at location x= 20 m

  • 7/27/2019 Top Side -Report

    15/22

    14

    Figure 21: Joint numbers at location y= 0 m

    Figure 22: Joint numbers at location y= 15 m

  • 7/27/2019 Top Side -Report

    16/22

    15

    Figure 23: Joint numbers at elevation (+) 10 m

    Figure 24: Joint numbers at elevation (+) 20 m

  • 7/27/2019 Top Side -Report

    17/22

    16

    Figure 25: Joint numbers at elevation (+) 30 m

  • 7/27/2019 Top Side -Report

    18/22

    17

    6 Load Simulation:6.1 Dead Load:

    TOTAL DEAD LOAD =8661.65 KN

    TOTAL WEIGHT OF THE STRUCTURAL STEEL= 882.94 MT

    Figure 26: Isometric view of dead load acting on the structure

  • 7/27/2019 Top Side -Report

    19/22

    18

    6.2 Live Load:TOTAL LIVE LOAD = 26279.99 KN

    Figure 27: Isometric view of the structure showing live load acting on the structure

    Figure 28: Isometric view of the cellar deck showing live load acting on the structure (EL = (+)20 m)

  • 7/27/2019 Top Side -Report

    20/22

    19

    Figure 29: Isometric view of the main deck showing live load acting on the structure (EL = (+) 30 m)

    6.3 Wind Load:

    Figure 30: Projected area along the north side

    Wind load acting on the overall projected area of the platform CS= 1

  • 7/27/2019 Top Side -Report

    21/22

    20

    Figure 31: Isometric view of the structure showing wind load ( 50 m/s from North ) acting on the structure

    7

    Results:0.8

  • 7/27/2019 Top Side -Report

    22/22

    21

    L-53FD CV 0.908 2002 0 -73.27 -21.53 -0.14 0.6 10.51 97.8 97.8 0.865 2001 0.834

    L-54ED CV 0.814 2003 0 -84.75 -17.88 -0.62 -0.08 8.03 85 85 0.768 2000 0.752

    * * J O I N T C A N S U M M A R Y * *

    (UNITY CHECK ORDER)

    LOAD STRN LOAD STRN BRACE LOAD

    JOINT DIAMETER THICKNESS YLD STRS UC UC DIAMETER THICKNESS YLD STRS UC UC JOINT CASE

    (CM) (CM) (N/MM2) (CM) (CM) (N/MM2)

    402L 76.2 3.81 345 0.399 0.394 76.200 3.810 345 0 0.394 404L 2003

    404L 76.2 3.81 345 0.399 0.392 76.200 3.810 345 0 0.392 402L 2001

    401L 76.2 3.81 345 0.398 0.394 76.200 3.810 345 0 0.394 403L 2003

    403L 76.2 3.81 345 0.398 0.392 76.200 3.810 345 0 0.392 401L 2001

    501L 76.2 3.81 345 0.23 0.261 76.200 3.810 345 0 0.261 4 2003502L 76.2 3.81 345 0.231 0.261 76.200 3.810 345 0 0.261 4 2003

    503L 76.2 3.81 345 0.23 0.26 76.200 3.810 345 0 0.26 6 2001

    504L 76.2 3.81 345 0.231 0.26 76.200 3.810 345 0 0.26 6 2001

    8 References:API RP-RA

    AISC 13th

    edition