tm-9-1005-211-34 M1911A1
Transcript of tm-9-1005-211-34 M1911A1
-
8/14/2019 tm-9-1005-211-34 M1911A1
1/47
TM 9-1005-211-34D E P A R T M E N T O F T H E A R M Y TECHW I-CAL MARUAL
DIRECT AND GENERAL SUPPORTMAINTENANCE MANUAL
PISTOL, CALIBER .45,AUTOMATIC, M191lAl
HEADQUARTERS, DEPARTMENT OF THE ARMY
22 JUNE 1964
-
8/14/2019 tm-9-1005-211-34 M1911A1
2/47
*TM 9-1005-211
Tech nica l Manual
NO. 9-1005-211-34
HEADQUARTERS.
DEPARTMENTOFTHEARMY
WASHINGTON. D.C., 20315 IIJune 196
CHAPTER 1.Section I.
I1.CHAPTER 2.CHAPTER 3.
Section I.I1.
CHAPTER 4.CHAPTER 5.
Section I.I1.I11.
CHAPTER 6
.
CHAPTER 7.
APPENDIX
PISTOL. CALIBER .45. AUTOMATIC. M1911A1Paragrapha Pa
INTRODUCTIONGeneral ......................................... 1-3 Description and data ................................. 4. 5 PARTS. SPECIAL TOOLS. AND EQUIPMENT . . . . . . . . . . . . . . . . 6-10
INSPECTIONSGeneral ......................................... 11 -13 1Inspection procedures ................................ 14 -16 13-GENERAL MAINTENANCE ............................ 17-23 18. REPAIRCartridge magazine .................................. 24 -28 2Barrel and slide group ................................ 29-33 22-2Recei ver group ..................................... 34 -38 28-3F INAL INSPECT ION .................................
39.4 03
PREPARA TION AND SHIPPING INSTRUCTIONS. . . . . . . . . . . . . .
41 -43 4REFERENCES ........................................... 4
I N D E X ............................................................ 4
'This manual supersedes TM42951.1 . 19 July 1957.
-
8/14/2019 tm-9-1005-211-34 M1911A1
3/47
CHAPTER 1
INTRODUCTION
Section I. GENERAL
1. scope
a. This manual is published for the in-
formation and guidance of personnel re-sponsible for direct and general supportmaintenance of the caliber .45 automaticpistol M1911Al. It contains informationon maintenance which is beyond the scopeof tools, equipmen t, or su pplies norm allyavailable to using organizations.
b. This manual contains a descriptionof and procedures for disassembly, in-spection, repair and assembly of the cal-iber .45 automatic pistol M1911Al. Th eappendix contains a list of current refer-
ences, including supply manuals, technicalma nu als an d other available publicat ionsapplicable to the materiel. The mainte-nance allocation charts are contained inTM 9-1005-211-12P/2. TM 9-1005-211-35P contains a list of repair parts andspecial tools.
c. TM 9-1005-211-12P/2 contains alis t-in g of operator and organizational main-tena nce repair pa rt s an d special tools.d. Lubricating instructions for the ma-teriel are contained in paragraph 23 ofthis manual.e. The direct report ing oferrors, omis-sions and recommendations for improvingthis equipment manual by the individualuser, is authorized and encouraged. DAForm 2028 will be used for reporting theseimprovements. This form may be com-pleted using pencil, pen or typewriter. DAForm 2028 will be completed by th e indi-vidual using the manual and forwardeddirect t o:
Commanding GeneralHeadquartersU. S. Army Weapons CommandATTN: AMSWE-SMM-PRock Island ArsenalRook Island, fllinois 61202
f. This manual differs f rom TM 9-2951-1 dated 19 July 1957 as follows:
(1) Adds pertinent information on:
2
(2)
(3)
Barr el and slide groupReceiver group
Cartridge magazineTroubleshootingTrigger pull testTrigger pull correctionHand function test.Revises information on:Special tools and equipmentImprovised toolsDirect and general support matenance.Deletes specific maintenance structions for caliber .45 autompistol M1911.
2. Direct and General Support
Maintenance Allocation
The publication of instructions for coplete disassembly is not to be constras authority for the performance by dirand general support maintenance unitsthose functions which are restricteddepots and arsenals. In general, the pscribed maintenance responsibilities wbe reflected in the maintenance allocatcha rt in TM 9-1005-211-12P/2. Supplyparts listed in the depot guide columnTM 9-1005-211-35P will bemadetodirand general support maintenance only wthe emergency nature of the maintenato be performed has been certified byresponsible officer of the requisitionorganization.
3. Forms, Records, and Reports
a. General. R e s p o n s i b i l i t y f o r tproper execution of forms, records. areport s rest s u pon th e officers of all unmaintaining this equipment. However, value of accurate records must be fuappreciated by all pers ons responsible their compilation, maintenance, and uRecords, reports and authorized formsnormally utilized to indicate the ty
-
8/14/2019 tm-9-1005-211-34 M1911A1
4/47
-
8/14/2019 tm-9-1005-211-34 M1911A1
5/47
-
8/14/2019 tm-9-1005-211-34 M1911A1
6/47
-
8/14/2019 tm-9-1005-211-34 M1911A1
7/47
6 SLIDE STOP
CARTRIDGE MAGAZINE
ORD F6Figure 3. Caliber .~6automolic pistol M19llAl _ exploded v iew .
6
-
8/14/2019 tm-9-1005-211-34 M1911A1
8/47
CHA PTER 2
PA RTS, SPEC IA L TO OLS, A ND EQ UIPMENT
6. GeneralTools and equipment and maintenance
parts over and above those available to the
using organization are supplied to directand general support maintenance units formaintaining and repairing the materiel.
7, Mointenonce PortsMaintenance parts are listed in TM 9-1005-211-35P. which is the authority for
requisitioning replacements.
8. Common Tools and Equipment
Stan dar d an d comm only used tools and
equipment having general application tothis materiel are authorized for issue bytables of allowances and tables of organ-ization and equipment.
9. Special Tools and Equipment
Special tools and equipment (table 1) andtool sets or hits are listed in and author-ized for issue in TM 9-1005-211-35P.This tabulation contains only those specialtools and equipment necessary toperform
the operations described in this technicalma nu al, is included for inform at ion only,an d is not t o be used as abasis for requi-sitions.
Ta6k I. Special Tools a n d E q u i p m e n t
BRUSH , C L E A N I N G , 5 5 0 4 0 3 6 4 19 b Toc l eanSMALL ARMS: MS b a r r e lb o r e . b o r e a n dcQ.l l lber.
F I X T U R E , MEAS- 7274758 5 , 3 6 400 T o check URING, T R I G G E R t r i g g e rPULL: pu l l .
Itern
H O L S T E R , P I S T O L :
M1916. h ip@lack ).ROISTER, P I S T O L :
M ,, s h o u l d e r(black) .
ROD, CLEANING,
SMALL ARMS:
ca l ..45, M 4 .
10. Improvised ToolsThe list of improvised tools in table
applies only topersonnelperformingdireand general support maintena nce on tpis tol. I llustrat ions giving dimensiondetails are included to enable personnto fabr icat e t he tools if desired. Th e chvalue of these tools is for maintenanpersonnel engaged in repairing a lar
nu mber of weapons. Th e following dat a for information only.
T a b l e 2. lmprouised Took
TOOL. s takingp l u n g e r t u b e .
3 1 6 T o stake b u s b i n a
-
8/14/2019 tm-9-1005-211-34 M1911A1
9/47
F i g u r e 4.Specialtoolsand e q u i p m e n t .
Figure 6. Trigger puZ2 measuring fixture 7.974768.8
-
8/14/2019 tm-9-1005-211-34 M1911A1
10/47
Figure 6. Hip and shoulder holsters.
F igure 7 . Impr ovised fizLwe for riveting front sight (1 of 2).RA PD 91
-
8/14/2019 tm-9-1005-211-34 M1911A1
11/47
QNECOF EACH,WDlOONE-WDmu XL . FIN/ HDN RxKt 56SEC (XT*IL*g.YBCLOw
ONE-WDIDd55TL(FOR 51(1HT Al3197-7) (FOR 510HT 230)
II* PD 91773
Figure g.imp-ouised tool for staking bushing.
-
8/14/2019 tm-9-1005-211-34 M1911A1
12/47
RA PO 9177Figure 10. Improvised tool /or slaking plunger t u b e .
-
8/14/2019 tm-9-1005-211-34 M1911A1
13/47
CHAPTER 3
INSPECTIONS
Section I. GENERAL
11. scopeThis chapter provides specific instruc-
tions for the inspection by maintenancepersonnel of materiel in the hands oftroops in the field, in .Ordnance shops,and in alerted units scheduled for overseaduty. Troubleshooting information is in-corporated wherever applicable as a nor-mal phase of inspection.
12. Purpose of Inspection
Inspections are made for the purpose of(1) determining the condition of an item asto serviceability, (2) recognizing condi-tions that would cause failure, (3) assuringproper application of maintenance policiesat prescribed levels, and (4) determiningthe ability of a unit to accomplish itsmaintenance and supply missions.
13. Categories of InspectionIn general, three categories of inspec-
tion are performed by direct and generalsupport maintenance personnel.
a . Inspection ofMateriel in the Hands ofTroops.
(1) Spot check inspection. This is aninspection performed on apercent-age of materiel in order to ascer-tain the adequacy and effectivenessof organizational maintenance andsup ply. Included within th is scopeis inspection of equipment to detectinc ip ien t f a i lu re s be fo re un-
serviceability occurs; inspection toascertain the availability and useof technical and supply manuals andlubrication orders; inspection todetermine the accuracy ofrecords,authorized levels of equipment andsupplies, practice of supply econ-omy. preservation and safekeepingof tools. availability of repairparts and supplies. and knowledge
of the proper procedures for resitioning supplies and equipmand follow-up thereon.
(2) Command maint enance. Commamaintenance inspections willperformed. at least,, annually. purpose of the inspection isascer ta in the serv iceabi l i tyequipment, to predict maintenaand supply requirements. anddetermine the adequacy of faciliand effectiveness of procedu
Information obtained during thespection should indicate futurequirements for depot maintenaand for replacement. as welldisclose immediate needs maintenance and applicationmodification work orders. Durinspection, correction of deficcies will be made on the spot wpractical. For additional infortion relative to these inspectiand the forms to be used therewrefer to AF I 750-E.
b. Ordnance Shop Znspection.(1) Initial inspection. This is an
spection of materiel receivedOrdn an ce shops for t he pu rposdetermining the degree of repand parts requirement. This cludes determination of modiftion work order s t o be applied
(2) In-process inspection. This ispform ed in t he pr ocess of repa ir
the materiel, to insure that parts conform to the prescrirepair standards. that the womanship is in accordance withproved methods and proceduand that deficiencies not discloby the initial inspection are foand corrected.
(3) Final inspection. This is an ceptance inspection performed
-
8/14/2019 tm-9-1005-211-34 M1911A1
14/47
a final inspector after repair hasbeen completed, to insure that themateriel is acceptable for returnto user or storage.
c. Preembarkation hspection ofMate-rielio Units Alerted for OverseaMove-ment. Th i s~ inspection is conducted onmateriel in alerted units scheduled for
oversea duty to insur e tha t such ma terwill not become unserviceable or worn oin a relatively short time. It prescriba higher percentage of remaining usablife in serviceable mate r i e 1 to meetspecific need beyond minimum servicability.
Section II. INSPECTION PROCEDURES
14. General
Wamfng: Before sta rt ing sn inspection,be sure to clear the weapon. Do not actuatethe trigger until the weapon has beencleared. Inspect the chamber to insurethat i t ie empty and check to see tha t noammunition is in position tobe introduced.Avoid having live ammunition i n the viom-ity of workarea.
a. Check to see that the weaponhas beencleaned of all corrosion preventive com-pound, grease, excessive oil, dirt. or for-eign matter which might interfere withproper functioning or obscure the truecondition of the parts. b. Make an overall inspection of the
weapon for general appearance, condition.operation, and manual functioning. Usedummy cartridges.
15. Inspection of Materiel in the
Hands of Troops
a. General. Refer to AR 750-8 for re-sponsibilities and fundamental duties ofinspecting personnel, the necessary noticean d prepa ra tions t o be made. form s to beused, and general procedures and methodsto be followed by inspectors. Materiel tobe inspected includes organizational spareparts and equipment and the stocks ofclean ing and pr eserving ma terials. In thecourse of this inspection, the inspector
will accomplish the following:(1) Determine serviceability, i.e., the
degree of ser viceab ility, comp lete-ness, and readiness for immediateuse, with s pecial i .eference to safeand proper functioning of the mate-riel. If the materiel is found un-serviceable or incipient failures
(2)
(3)
(4)
(5)
(3)(7)
(3)
(9)
a re disclosed, t he deficiencies wbe corrected on the spot or advgiven as to corrective measuwhen applicable, or , if necessathe materiel will be tagged delivery to. and repair by Ordnanmaintenance personnel.Determine causes of mechani
and functional difficulties thtroops may be experiencing acheck for apparent results of laof knowledge. misinformation, glect, improper hand l ing and stage. secur ity, and preservat iongee that all authorized modifitions have been applied. that unauthorized alterations have bemade, and that no work beyond authorized scope of the unit is beatt empted. Check t he index in DPam 310-4 and the current MWfiles for any MWOs printed afthis publication.Instruct the using personnel p r op e r preventive-maintenanprocedures where found inadquate.Check on completeness of the ganizational maintenance alloances and procedures for obtainreplenishmenta.Check serial number stamped
weap on for legibility.Note general appearance. Cheexterior of materiel for missior broken part s.Check storage conditions of genesupplies and ammunition.Initiate a thorough report on mariel on deadline, with reaso
-
8/14/2019 tm-9-1005-211-34 M1911A1
15/47
(10)therefore, for further appropriateaction.Report to the responsible officerany carelessness, negligence, un-authorized modification, or tam-pering. This report should be ac-oompaniedbyrecommendationsforcorrecting the unsatisfactory con-dition.
h.SpeCi f i c . The specific groups and as-semblies to be inspected for s erviceabilityare listed in TB ORD 587 and also are ap-plicable to preembarkation inspection.
c. Safe ty Tests. Perform the followingsafety tests as indicated in (1) through (4)below.
(1) Safe ty test ( f ig . 11). With the pis-tol unloaded, cock the hammer andpress the safety upward into thesafe (locked) position. Grasp thegrip so the grip safety is depressed
and squeeze the trigger tightlyth ree or four times. I f the hammerfalls. the safety must be replaced.
(2) Grip sa fe ty tes t ( f ig . 12). With thepistol unloaded, cock the hammerand without depressing the gripsafety point the pistol downwardand squeeze the trigger three orfour times. If the hammer fallsbecause the grip safety is de-pressed by its own weight, the gripsafety m ay be oorr eotedby replac-
(3)ing sear spring.
Ha lf-cock posi tion ( f ig .
14). With the pistolunloaded, draw
back the h amme r until the sengages the half-cock posinotch. Then squeeze the trigIf the hammer falls, the hamor sear must be replaced orpaired. Draw the h amme r bnearly to full cock position. dosqueeze trigger, and t h en l e t thslip off h a ~mm e r . The hamshou ld fa l l on ly to the ha l f -cn o t ch . Replace hammer whefalls ua s t the half-cock positio
(4)Disconn ector tes t .(a ) With the pistol unloaded, c
the hammer. Push the slide gl/4-inch to the rear (fig. 15)hold in that position while squing trigger. Let slide group
GRIP SAFETYNOT DEPRESSED
F i g u r e 1% Grip safety lest.
F i g u r e 13. Half-cock p o s i t i o n test(1 of 8
-
8/14/2019 tm-9-1005-211-34 M1911A1
16/47
-
8/14/2019 tm-9-1005-211-34 M1911A1
17/47
-
8/14/2019 tm-9-1005-211-34 M1911A1
18/47
, - MOVE SLIDE GROUPl /&INCH - PULL TRIGGER
POSlTONlNG SLIDE GROUP TO DETERMINE IFDISCONNECTOR IS WORN.
SLIDE GROUP
SLIDE STOP ENGAGED t..; :1
NOTE: HAMMER SHOULD NOTFALL WHEN SLIDE GROUP 15RELEASED.
SLIDE GROUP IN REARWARD POSITION, PREPARING TORELEASE SLIDE STOP.
SLIDE GROUP IN FORWARD POSITION PRIOR TO TESTINGHAMMER. ORD i=,bZO
Figure 16. Disconnector test.
-
8/14/2019 tm-9-1005-211-34 M1911A1
19/47
CHAPTER 4
GENERAL MAINTENANCE
17. General
This cha pter provides th e neoessaryin-s t ruc t ions on the general maintenanceprocedures to follow. The followingmeth-ods and procedures given in this chapterar e to be car efully observed dur ing repa iropera tions. This cha pter includes t he dis-assembly and assembly procedures, re-placement of par ts , use of tools, cleanin g,finished surfaces, removal of burs. andtns t ruc t ions on lubrication.13. General Repair Methods
a. Disassembly and Assembly Procedures.(1) In disassembling a unit, remove
the major subassemblies and as-semblies whenever possible. Sub-assemblies may be disassembled,as necessary, into individual parts .
(2) During assembly. subassembliesshould be assembled first, theninstalled to form a complete unit.Lubricate all component partslightly before assembling.
(3) Complete disassembly of a unit isnot always necessary in order tomake a required repair or re-placement. Good judgment shouldbe exercised to keep disassemblyan d assembly operat ions t o amin-imum .
b. Replacement of Parts.0)
(2)(3)
When assembling a unit, replaceall pins when necessary. Replacegrip screws or bushings whendamaged.All spr ings will be replaced if theyare broken. bent, cracked or if theyfail t o function properly.If a r equired new part is not avail-able, a reconditioned used partmay be substituted. Such recondi-tioned used parts will be examinedcarefully to determine their serv-iceability.
c. Use af Tools(1 ) Care must be exercised to use too
that fit and are suitable for the tasto be performed in order to avo
unnecessary mutilation of parand/or damage to tools.
(2) Special tools are listed in t ab leand are provided for the maint
nance of the m at eriel. These toowill be used only for the purposfor which they are intended.
(3) Keep tools clean and work wiclean parts. Normal rules of goohousekeeping must be observed.
19 . Cleaninga. As assemblies are removed and di
assembled, component items should bplaced in a wire basket a nd cleaned t hooughly of all grease, oil, water and dirusing dry cleaning solvent (SD). Dthoroughly with clean wiping cloths anoil lightly us ing general pu rpose lubricaing oil (PL special).b. Clean the barrel bore, chamber, an
all parts that come in contact withpowdresidues, using solvent cleaning compoun(PD 126). Cleaning rod IvI4, 5564102 (fi4) and small arms cleaning brush M5504036 (fig. 4) are used to clean thbarrel bore. Saturate brush with PD 12and run through barrel. Remove brusclean the rod, insert two swabs in slot rod and dry the bore thoroughly or untswabs appear clean after running througbore. Then use one swab saturated wiPL special t o oil inside of bore lightly anall exterior surfaces to prevent corrosioor rust.
c. On those component parts whichcota in a ha rd carbon r esidue, it ma ybe neessary to clean these parts with carboremoving compound (P-C-111A). Cleaniinstructions are as follows:
Warning: Avoid skin cont act. Th e compound should be washed off thoroughly wiru nn ing water if it comes tn contact wi
18
-
8/14/2019 tm-9-1005-211-34 M1911A1
20/47
the skin. A good lanolin base cream, afterexposure to compound, is helpful. The useof gloves and protective equ tpmen t isrecommended.
(1) Using a suitable container, fill withfresh compound.
(2) Before soaking components remove
(3)
(4)
(5)
loose grease; dirt and oil fromparts as indicated inparagraph 19a.Imm erse par ts, cont aining car bonresidue, in container. ,Allow barrel to soak for 2 hoursor until all traces of carbon havebeen removed.Rinse with water, kerosene, orsolvent . To effectively r emove car -bon, brush with a stiff bristlebrush under r unn ing water.Wipe the parts dry and oil.
Note: P-C-IIIA is considered a supp lemen t foruse in direct end general support meintenenoe levelsonly in extreme cases and not as a substitute forP D 126.d. Clean receiver, using dry cleaning
solvent (SD).e. On components that contain an ac-cumulation of light rust, use a clean clothmoistened with PD 126. If this does notsuffice, use crocus cloth. Make certain itdoes not scra tch or a lter t he finished sur -faces. Remove all dirt and abrasives; oilsurfaces before assembling parts.
f . N ew material and component parts,
received from storage for immediate use.ma y have hea vy accum ulat ions of grease.Place material or components in wirebasket and lower in vapor degreasing vator wash in dry cleaning solvent (SD). Dryth oroughly as indicat ed in par agraph 19aand oil. Lubricate as specified in para-graph 23b.g . For cleaning instructions of Ordnancemateriel. refer to TM 9-208-l.
20.General Precautions in Cleaning
a. Dry cleaning solvent (SD) is flam-mable and should not be used near an openflame. Fire extinguishers shouldbe readilyavailable when using these materials. Inaddition, they evaporate quickly and havea drying effect on the skin. When usedwithout rubber gloves, they may cause
cracks in the shin, and in the case of soindividuals, a mild irritation or inflammtion. Use only in well-ventilated place
b. The u se of diesel fuel oil. gasolinebenzene (benzol) for cleaning the weapis prohibited.
c. Store solvent cleaning compound (126) in a warm place, if practical. Do dilute or add an tifreeze.
Note: Sandblasting is permissible on nonworksurfaces for removal of dirt and rust.
21. Finished Surfaces
a. All treated surfaces will be refinishto match the appearance of new parts.
b. For detailed information on finishsurfaces, refer to TM 9-1861.
22 . Removal of Burs, Screwheodsand Working Surfaces
a. During the entire life of the pistpolishing and stoning are necessary to lieve friction and to remove burs causby usage. Burs on screwheads and lsurfaces should be removed with a fifile or stone. Burs on such working sfaces as the receiver sliding rails, ceiver housing areas and bearings shoube removed with a file or stone and poliswith crocus cloth.
Cau tmn : Care will be exercised to stoor file evenly and lightly and not remomore metal than absolutely necessarymaintaincorrect contours. Critical dimsions of parts or assemblies must not altered in any way that would affect functioning or interchangeability of pa
b. Roughspotscausedbyscores, galligouges and rust pits will be smoothedenable all part s t o operat e normally. Tfinish of the repaired component will
approximately that of the original finis
23. Lubrication
a . Make cer ta in a l l meta l par ts
cleaned and dried thoroughly in accoan ce with instr uctions cont ained in pagraph 19.
-
8/14/2019 tm-9-1005-211-34 M1911A1
21/47
b. All meta l part s will, be lubricated by lubricate sliding surfaces to reduce frapplying a light coat of general purpose tion and assure free movement.lubricating oil (PL special). As a part of c. Lubrication and preservation maall assembly and installation operations, rials are listed in TM 9-1005-211-12P
20
-
8/14/2019 tm-9-1005-211-34 M1911A1
22/47
CHAPTER 5
REPAIR
Section I. CARTRIDGE MAGAZINE
24. Removal
Refer to figure 16 for removal of car-tridge magazine.
25. Disassembly
Detailed disassembly of cartridge mag-azine is not necessary for inspection. Ifanzepart is unserviceable, replace maga-
.26. Cleaning
Refer to paragraph 19 for cleaning.
A - REMOVlNG MAGAZINE,
27. Inspection
Inspect the exterior of magazine (fig. for burs or other damage. Checkfor sptension and for the correct assemblmagazine spring.
Note. Small spring loop mus t be up and tfront.
28. Installation
Refer to figure 16 for installationmagazine.
NOTE: PVSH DOWN TO RELEASESLlDESTOP WHICH RELEASESSLIDE AFTER INSTALLATION OFMAGAZINE.
B- ,NSTALLlNG MAGAZINE. ORD F6Figure 16. Remove/install oar t t i dge magaaine.
-
8/14/2019 tm-9-1005-211-34 M1911A1
23/47
Figure 17. Cartridge magazineinspect ion points.
Section II. BARREL AND SLIDE GROUP
29. Disassembly
NO&?. White arrows, shown on illustrations, indi.ate removal or disassembly and black arrows as .sembly or insta l la t ion.
Refer to figur es 18 t h r u 2 1 for disassem-bly of barrel and slide group.
Warn ing: Wherever springs arefound t obe under tension or pressure, extreme careshould be exercieed when removing com-ponents. Keep the finger and thumb overapplicable components to prevent lnjurytopersonnel or loss ofparts.30. Cleaning
Refer to paragraph 19 for cleaning.
31. Inspection (fig. 22)
a Inspect the barrel for burs ontheeex-terior an d inter ior r im of th e mu zzle. In-
spect the barrel for pitting, bulges, asha rp ness of lan ds (figs. 23 th rough 25
b. Barrel must be straight. as detmined visually, clean and f ree of corrosi
c. Pits in the chamber are allowablethey are not large enough to cause extrtion difficulties.
d . Pits as wide as a land or groove aless tha n th ree-eight s inch ar e allowabBarrels containing pits as indicatedfigures 23 t hr u 25 will be rejected.
e. Scattered or uniformly fine pitsfine pits in a densely pitted area arelowable. Tool marks or scratches accepted, regardless of length. Tool mawill appear on lines running laterallythe grooves or may run spirally acrthe top of lands.
f . Defini tely r inged bores or boringed sufficiently to bulge the outs
22
-
8/14/2019 tm-9-1005-211-34 M1911A1
24/47
REMOVE/ INSTALL RECOIL SPRING PLUG AND SPRING.
A - TURN REARING CLOCK- 8 - BEARlNG POSITIW~WY TO REMOVE, COUNTER- FOR=OR4~TALLATON@CLOCKWSE TO INSTALL.~~~ _~~. ..____. .~-..a
REMO E/ lNSTALl BARREL BEARING. COCK HAMMER FOR REMOVING/ INSTALLINGSLIDE GROUP.
-
8/14/2019 tm-9-1005-211-34 M1911A1
25/47
i__~~.,,&llON SLIDE GROUP.
REM,,E,INSTA lL SLIDE STOP.
- NOTE: PUSHPIN FROMRGHT TO LEFT TO RE-MOVE, AND FROM LEFT
TO RGHT TO IN STALL.
UNSEAT/ SEAT PINPORTON OF SLIDE STOP.
RECEMR GROUP
~~o~p~,lNSTALL SLIDE GROUP FROM RECEIVER
BARREL GROUP BARRELI LINK SLIDE GROUP
NOTE: BARREL LINKMUST BE IN FORWARD
POSITION FOR RE-MO A,, INSTALLATION .~__..~~. ~~._~_ ~,,
,WAOW.,,NSTALL RECOIL SPRING GUIDE.
F i g u r e lg. D i s a s se m b l y / a s s em b l y of b a r r e l a n d s l i d e group (9 of 4%
F~EMO,E,,NSTALL BARREL GROUP.ORD FM
24
-
8/14/2019 tm-9-1005-211-34 M1911A1
26/47
NOTE: INSTALL FROMRIGHT TO LEFT.
REMOVE/ INSTALL BARREL LINK PIN.-wFIRING PIN
ICIj PIN AND STC >P.REMOVE/ INSTALL FIRING PIN STOP.
we EXTR;CTOR
L
.._~..REMOVE/ INSTALL BARREL LINK.
FIRING PIN+-
I,STO P .,1
FIRING PIN AND FIRING
EXTRACTOR AT FIRING PINSTOP SLOT. REMOVE,,NSTALL CARTRIDGE EXTRACTOR. OR0 P
F i g u r e 20. D i s a s se m b l y / a s s em b l y o f b a r r el a n d s l ide group (3 of 4).
-
8/14/2019 tm-9-1005-211-34 M1911A1
27/47
FRONT SIGHT
. REMOVE FRONT SIGHT. ,NSTALL FRONT SIGHT.
REMOVE/ INSTALL REAR SIGHT. REAR SIGHT REMOVED.
ORD F&514
Figure 21. Disassembly/assembly of barrel and slide group (4 of 4).
surface of the barrel are cause forrejec-t ion . However, faint rin gs or sha dowy de-press ions do not indicat e an un serviceablebarrel and should not be cause for rejec-tion.g. Inspect the barrel bearing for bursan d excessive wear .b. Inspect slide for breaks or cracks,especially around the ejector port, Inspectthe interior grooves and ejector port ofslide for excessive wear and burs. Checkfor loose front or rear sights.i. Inspect the firing pin for wear orshortn ess. The pin, as ma nu factured. hasan overa ll lengt h of 2.290 to 2.296 inches .
2b
j. Inspect the recoil and firing psprings for weakness or breakage. Thfree length of recoil spring should bapproximately 6-l/2 inches.k . Examine the extractor for weaweakn ess. broken lip or deform at ion.
1.Inspect the recoil spring plug, recospring guide. firing pin stop, barrel lin
and pin for burs an d distort ions.
32. Repair
a. Remove burs on exterior and interiorim of barr el and bar rel cha mber by usina fine stone.b. Replace barrel if cracked, bulged o
-
8/14/2019 tm-9-1005-211-34 M1911A1
28/47
I NG -6008596
STOP - 5013205
LINK PIN - 5013199EXTRACTOR -
RECOIL SPRINGPLUG - 5013201
FIRING PIN -
ORD F&S15Figure ee . Barrel and slide grocrp- inspection points.
OR0 F6620Figure $4.. Interior of b a r r e l showing pitt ing anddull landa-cutaway view.
ORD F6621
Figure &S. Interior of barrel showing pitting, wornlands a n d bum -cutou~uoy view.
pits are larger than the width of a land
groove or more th an th ree-eight hs inchlength. Also. replace barrel if link lugs adamaged or broken.
C. Replace barrel bearing if worn. Rmove burs using a fine stone.
d . Replace barrel link and/or pmworn, deformed or damaged.
e. Replace worn, damaged or short ing pin.
f. Replace .cracked or we ak recand/or firing pm spring.
g. Replace extractor if worn or lipbroken.
IL Remove burs from recoil springpan d guide. Replace, if worn or dam age
i. Replace front or rear sights t f daged to such an extent that the contoueither sight would be insufficient forcurate sighting of weapon.
-
8/14/2019 tm-9-1005-211-34 M1911A1
29/47
j. If front sight is loose; r e s t ake , usingriveting f ix ture .
k. Jf rear sight is loose, remove sight,peen top portion of dovetail slot and r e-place rear sight, u singbra ss dr ift (fig. 21).
33. Assembly
Refer t o figur es 18 th ru 21 for assemblof barrel and slide group.
Note. Whenassembl ing f i r ingpinandrecoi l spr ingsmal l loop of spr ings w i l l be t o t he r ear .
Section III. RECEIVER GROUP
34. Disassembly
Refer to figures 26 thru 32 f o r d i s a s -sembly of receiver group.
35. Cleaning
Refer to paragraph 19 for cleaning ofreceiver group.
36. Inspection
a. Inspect the trigger for burs sndwear(fig. 33). Inspect the half-cock positionnotch and full-cock notch of hammer forcracks, chips or wear. Make certain theham mer st rut is not bent or cracked.b. Inspect the sear for worn or chippedtips or worn lugs.
c. Inspect the sear spring for brokenleaves, cracks and tension.d. Inspect disconnector for burs andwear .
e. Insp ect t he grip sa fety for burs, wearand cracks on the tip which engages thetrigger.
f . Inspect the pin portion and lug ofsaket y for wear or da ma ge.g. Inspect the helical compression hous-
ing spring (fig. 34) for cracks and tension.h. Inspect mainspring cap pin. detentplunger, and st ra ight -headed pin forbur s,wear or dama ge.i. Inspect for bent or worn mainspringhousing pin and spring pin.
j . Inspect slide stop, slide stop plungeran d safety plunger for bu r s , wear or dam-age.k. Inspect magazine catch and magazinecatch lock for burs and wear. Checkmag-az ine catch spring for tension and damage.
I. Inspect helical compression spring(housing) for bu rs on ma tin g surfaces an d
lan yar d loop for being bent . worn or da maged.
m. Inspect grips for cracks and worcheckering.
n. In spect th e r eceiver housing (fig. 35for wear or burs in the s l ide matingrooves. Inspect t he receiver for deform ation. Check to see that the plunger tubeejector, ejector pin. and grip screwbushings are not burred or worn. Check thmainspring housing mating grooves in threceiver for burs. Check slide stop notcfor oversize or wear.
37. Repair
a. Remove burs from slide mating surfaces of receiver housing and mainsprinhousing mating surfaces, using a finstone.
b. Replace slide stop plunger a nd sa fetplunger, and ejector if worn or damaged
Replace plunger tube using stakingplungetube tool. Replace all bushings th at ha vbeen removed from receiver housing, usinstaking bushing tool.
c. Remove burs from trigger, replacif worn or damaged.d. Replace hammer if cracked. chippeor worn.
e. Rep 1 ace hammer s t ru t i f ben tcracked, worn or damaged.f. Replace sear if lugs are worn antips a re worn or chipped.
g. Replace sear spring if leaves arbroken or cracked, or tension is weak.h. Remove burs from disconnector, replace if worn or dam aged.
i. Remove burs from grip safety, replace if cra cked or worn on tip.
j. Replace safety if worn or damaged.k. Replace the helical compressio
28
-
8/14/2019 tm-9-1005-211-34 M1911A1
30/47
REMOVE HMMER PIN.----
REMOVE MAINSPRING HOUSING PIN.
RELEASE HbMMER PRIOR TO REMO lNGHAMMER PIN.
HAMMEGROU
HAMMER PIN
REMOVE HAMMER GROUP
MAINSPRING
MAINSPRING MOUSI
!__ _ ~._ 1~~Rj,.tOE MAINSPRING HOUSING ASSEMBLY.
ORD M62
Figure 26. Di sassembly/assembly of receiver group (1 of 7 ) .
-
8/14/2019 tm-9-1005-211-34 M1911A1
31/47
,NSTALL MAlNSPRlNG HOUSING PIN.
,NSTALL AND POSITION SAFETY.
DIOS,,AA&,EB STRUT AND INSTALL GRIP SAFETY.
R EL EASE HP.MMER A N D POSTON HAMMERSTRUT,NTO MAlNSPRNG HOUSING ASSEMBLY.
C OCK HAMMER PRlQR TO INSTALLING SMETY.
HAMMER STRU
/-MAlNSFnlNG
.
PARTALLY INSTALL MAINSPRING HOUSING ASSEMBTO HOLD SEAR SPRING IN POSITION.
ORD F&2
-
8/14/2019 tm-9-1005-211-34 M1911A1
32/47
NO TE: WHEN INSTALLINGHEAD OF PIN StiO LD BEON LEFT SIDE.
HAMMER
REMOVE/INSTALL HAMMER STRUT PIN.
DEPRESS SP??ING
REMOVE/ INSTALL STRAIGHT HEADED PIN.
INSTALL HAMMER AND HAMMER PIN.
& --P I N
SEPARATE/ CONNECT HAM MER STRVTAND ,,AMMER.
PLUNGER
STRAIGHTHEADED PINI
REMOVE/INSTALLMAINSPRING, CAP PIN,HELKMCOMPRESSION SPRING AND DETENT PLUNG ER.
OR0 I%6
-
8/14/2019 tm-9-1005-211-34 M1911A1
33/47
sEPnaArE,cor~Ntcr CElENT PLUNGER, HELICAL, COMPRESS,ON SPRING ANI, MAlNSPRlNG CAP PIN.
4PHOUSING
_..~, .~ *YPARATE/coNNECT LANYARD LOOP. REMOVE GRIP SAFETY.
# NOTE: REMOVEPIN FROM RlGtiTTO LEFT. WHENINSTALLING, HEADOF P,NSI?OULD BEON LEFT 5113E.
ORD FM2
32
-
8/14/2019 tm-9-1005-211-34 M1911A1
34/47
SEAR/LUG DISCO&ECTOR.
SEPARATErONNECT SEAR AND DISCONNECTOR.
MAGAZINECATCH SPRING
_ CATCH OPENING.r t-4:
TURN CLOC KWISE FORMAG G
INSTALLATION, COUNTER- CATCHT
CLOCKWISE FOR REMOVAL.
\ / FSEPARATE/ CONNECT MAG AZINE CATCH LOCK ANDMAG AZINE CATCH SPRING.
DISCONNECTOR
REMOVE/ INSTALL SEAR AND DiSCONNECTOR
T&N L& KM INDICATED 90 DEGREES.,-4 \ \ -/ $
;tWWLOCK CATCH POSITIONING CATCHGROUP
REMOVE/INSTALL MAG AZINE CATCH G ROUP.
REMOVE/ INSTALL TRIGGER.
ORD F&S
-
8/14/2019 tm-9-1005-211-34 M1911A1
35/47
4p,7----.___
REMOVE/ INSTALL GRIP SCREWS. REMOVE/INSTALL PLASTIC GRIPS.
REMOVE/INSTALL SLIDE STOP PLUNGER, HELlCAL COMPRESSION SPRING AND SAFETYPWNGER
STAKING TOO
_,~_NKATING PLUNG ER TUBE INSTALL&ME PLUNGER TUBE ON RECEIVER.ORD F66
F i g u r e 3 , . Disassem bly/ assem bly o f r e c e i v e r group (6 of 7).
-
8/14/2019 tm-9-1005-211-34 M1911A1
36/47
REMOVE PLUNGER TUBE
REMO t,,NSTAtt CARTRIDGE EJECTOR.
NOTE: REMOVE PIN FROM [
REMOE,,NSTAtL EJECTOR PIN.
REMOVEGRIP SCREWBUSHINGS.
,PUNCHAGRIP SCREWSHlNG
/I BUSHINGSTAKING TOOL
INSTAU AND STAKE GRIP SCREW BUSHINGSORD Ht.
F i g u r e 38. DisasaembZy/assembly o f r e c e i v e r g r o u p (7 of 7).
-
8/14/2019 tm-9-1005-211-34 M1911A1
37/47
TRIGGER - 6147780I HAMMER - 5503839
JHAMMER STRUT
- 60085on
SAFETY - 5503840
SEAR PIN - 501321 I
HAMMER PIN -5013205
GRIP SAFETY -6501828
ORD FL.617Figure 33. Receiver gnmp- inspection points (1of 3).
SLIDE STOP - 6WR.m MAGAZINE CATCH - 6008609SPRING - 5cl13217 AlNSPRNG HOUSING PIN - 5013212
SPRING PIN - 969W-HELICAL COM PRESSION
,+EL,CAL COMPRESSIONSPRING - MI3154
Figure 34. Receiver group - inspection points (2 of3).spr ing (housin g). if dam aged or t ension isweak.1. Remove hurs from mainspring cappin, detent plunger. and straight headed
36
pin. Replace, if worn or dam aged.m . Replace mainspring housing pin andsprin g pin if bent or worn .
n. Remove bu r s from slide stop, slide
-
8/14/2019 tm-9-1005-211-34 M1911A1
38/47
F i g u r e 36.Receivergroup - inspection point8 (3of 3) .
stop plunger and safety plunger. Replace,if worn or damaged.
o. Remove burs from magazine catchand magazine catoh lock. Rep lace ifworn.Replace magazine catch spring if damagedor tension is weak.
p. Remove burs from the mating sur-faces and mainspring housing. Replacelanyard loop if bent or damaged.
q. Replace grips if broken or cheokin g is worn .38. Assembly
Refer to figures 26 t h r u 32 for sssebl ing of receiver group.
-
8/14/2019 tm-9-1005-211-34 M1911A1
39/47
CHA PTER 6
FINAL INSPECTION
39. General
Pistols turned in for repair may beassu med t o ha ve defects caus ed by use orneglect. When th ey were a ccepted a s newweapons, th e par ts composing t hem weredimensionally correct and made of theproper material. The inspection of theseweapons after repair will differ from theinspection procedure used in the manufac-turing plant in that at t e n t ion will bedirected to wearing surfaces, parts thatmight crack or break due to high stressor fatigue, and evidences of corrosion.
These defects do not evidence themselvesby uniform reduction in a given dimensionbut show up as a chipped edge, a partiallyworn sur face, or an eccent ric hole. Agageused in man ufactu ring is merely a meansof comparing an unknown dimension with aknown one to judge whether a piececomeswithin tolerances. After this piece is wornthrough use. the change in dimension ismore easily detected in many cases bycomparing with adjacent, surfaces; thepiece in itself becomes a gage. Visual
inspection, therefore, is far more applic-able in these cases and gaging is limitedto those dimensions that are critical orthat may be more advantageously meas-ured than compared. Inspection of non-critical par ts (part s th at do not ordinar ilycau se ma lfun ctions) will be limit ed t o ap-pearance and the presence of cracks orflaws. The dimensions and tolerancesplaced on the parts (and gaging used duringmanufacturing) were for the sole purposeof insuring interchangeability. Even if the
dimensions of such parts are worn oon-siderably below drawing tolerance, func-tioning and inter cha ngeability will not beadversely affected and the parts are con-sequently aoceptahle. The serviceabilityof the material must also be determinedby conducting inspection as described inparagraphs 13 through 16.
40. Specific Inspection Proceduresa. Visual Inspection. Visual and overa
appearance of the pistol should be approxma tely th at of a n ew weapon. All exposemetal surfaces are to have a phospha t efinish. The color will range from black tmedium light gray. Bright surfaces arobject iona ble from s ta ndpoint of visibilitwhen th ey ar e capable of reflectin g lighAll outside surfaces will be free of bu ror deep s cr a tc he s. Barrels must bstraight, clean and free of rust andpowdefouling and free from bulges and ring
Pistols must be complete. All applicabmodificat ions m ust be applied. The ser inumber must be legible and allparts mube free of rust. Visually inspect the following:
(1) Check front an d r ear sight s, makcerta in they are t ight andpr opera l ined .
(2) Check for split or d am agedplastgrips and loose grip screws.
b. Functional Znspection.(1) Check functioning of safety. Refe
to paragraph 15c(l).(2) Check functioning of grip safety
Refer t o paragra ph 15c(2).(3) Check functioning of hammer o
sear. Refer t o par agraph 15c(3).(4) Check functioning ofdisCOMeCtO
Refer t o paragra ph 15c(4).(5) Upon completion of inspection, pi
tols will be properly cleaned anlubricated , (gara$raphs 19 and 23
o. Trigger Pull Test. Check the triggepull using trigger pull measuring fixtur
(figs. 5 and 36) and in accordance witinstructions indicated in (1) and (2) below
(1) With the safety unlocked, rest thweight on the floor and hook thnotched portion of the rod over thcenter portion of the trigger.No t e . Make certain the rod does notcontact or rub any portion ofthe pistol and th
-
8/14/2019 tm-9-1005-211-34 M1911A1
40/47
rod snd barrel we patallel. Empty magazinemust be insta l led when check ing t r igger
pull.(2) Depress grip safety and carefully
raise the weight from the floor.When using the 5 pound weight(minimum), the trigger should notrelease the h amm er. When u singthe 6.5 pound weight (maximum),the t r igger should release thehammer .
Caution: A slow or steady liftmust be uti lized to assure a tru eand accurate check.
-i HAh4MERCOCKED
TRIGGER PULLMEASURING FIXTURE
7274758
5.0 POUNDS MIN.6.5 POUNDSMAX.
ORD F&SW Figure 36. Checking trigger pull.
d. CorrectinP Tri&?er Pull.--(1)
(2)
(3)
Tri@e~pullUtk light. This is edence of a worn cocking notch the hammer, worn or damaged sor a weak helical compressihousing spring. Examine the coponents for wear or damage.trigger pull cannot be corrected stonfng, replace with new compnents as required.Trigger pullexces sive. T h i 8evidence of burs or surface irreularities on the hammer full-conotch or sear. A helical housspring that is damaged or too stroand/or interferences or bindbetween the mating surfaces of pertinent parts within the receivgroup are other probable causIf the trigger pull cannot be crected by stoning, replace with n
components as required.Creep in trigger. Creep is definas a perceptible movement of ttrigger after the slack has betaken up and before the hammerreleased. It is caused by roughuneven mating surfaces of the sehammer, and disconnector and aby unserviceable sear and hammpins. If the creep cannot be orected by stoning, replace wnew components as required.Caution: While stoning. critidimensions should not be altere
e. Hand Function Test.(1) Place three dummy cartridges
magazine (fig. 37). Insert magazin receiver group. Release slistop. This action would cause brel and slide group to move fward. At the same time, a dumcartridge will be stripped fromagazine into chamber of t
weapon.(2) Release safety (fig. 38).(3) Squeeze trigger, allowing hamm
to fall (fig. 39). Continue test unthird cartridge has been ejectfrom the pistol, simulating dfiring.
(4) When last cartridge is ejectslide group should remain look
-
8/14/2019 tm-9-1005-211-34 M1911A1
41/47
in open position by slide stop (fig. quired functioning test willbe o40). reoted by replacement of defect
(5) Pistols that fail to meet the re- components.
Figure 37. Position of bonds when loadingweapon -left front view. Oii i F66
Figure38, ,,ammer c o c k e d -reodk to beginfunction fit-in&?.
Figure 40. Slide group locked in open positio
Figure 99. Weapon in battery posilion.
40
-
8/14/2019 tm-9-1005-211-34 M1911A1
42/47
in open position by slide stop (fig.40).
(5) Pistols that fail to meet the re-
Figure 37. Position of hands when loadinpweapon -zeft front view.
quired functioning test will be oreoted by replacement ofdefectcomponents.
L RELEASE SAFETY
AMMEI
F i g u r e 39. Weapon in battery position.
-
8/14/2019 tm-9-1005-211-34 M1911A1
43/47
CHAPTER 7
PREPARATION ANDSHIPPING INSTRUCTIONS
41. Preparation
a C1eaoing. All metal parts shall beth oroughly clean edbyprocess C-3 of Spec-ification MIL-P-116C. Surfaces of partssubjected t o bur ned powder r esidues willbe cleaned with solvent cleaning compound(PD 126) conforming toSpecification MIL-C-372B.b. DryIn& All surfaces will be thor-oughly dried by wiping with clean cloths orby blowing the surface with ab l a s t of cleandry compressed air from a line equippedwith filter moistu re t ra ps.
c. Preservation. Pistols will be coatedwith a lubricating oil (PL special) mak ingcertain all surfaces are covered, includingthe entire bore of barrel.d. Packaging. Each pistol will be indi-vidua lly wrapped in a heavy-dut y grease-proof paper. All protruding edges will becushioned, using several thicknesses ofgrease-proof paper prior t o wra pping.
e. Packing. Pack a maximum of5Opis-tols in a suitable wood container box.
Make certain they are adequately blocto prevent movement during handling shipping. After closure, apply two flat sstraps around the box.
Note. For further pertinent information and ance in preservation, packaging and packing oabove named materiel. refer to TM 38-230.
42. Marking Instructions
Standard and precautionary markiwill be applied to boxes as prescribedTM 9-200.43. Shipping Instructions
a. Responsibility. When shipping pistol the officer-m-charge of preparthe shipment will be responsible properly processing the materiel for shment. including the preparation of Arshipping documents.
b. Army Shipping Documents. P r e pa ll Army shipping documents ln aocosnce with AR 725-50.
-
8/14/2019 tm-9-1005-211-34 M1911A1
44/47
-
8/14/2019 tm-9-1005-211-34 M1911A1
45/47
-
8/14/2019 tm-9-1005-211-34 M1911A1
46/47
-
8/14/2019 tm-9-1005-211-34 M1911A1
47/47
B y O r d e r o f Sec r& a ry of the Army:
Off i c i a l :
J . C . LAMBERT,Major General. Untied Slates Amy,The Adjtinnt General.
E A R L E G . W H E E L EGene r a l , United Slates AChief of Stat/.
Distribution:
Active Army:USASA (2) Armies (3) except
DCSLOG (1) Sixth (1)
CNGB (1) Cow (2)C/COMMEL (1) USA Corps (2)
USA Ord CD Agcy (2) Div (2)CofEngrs (1) Bde (2)TSG (I) Regt/Cp/BG (2)USCONARC (3) Bn (2)ARADCOM (2) Co/Btry (1) exceptARADCOM Rgn (2) Ord Co (2)
OS Maj Comd (2) except Br Svc Sch (2) excep tUSAREUR (3) Ord Sch (50)
USARJ (3) GENDEP (OS) (1)
USAMC (5) OrdSet, GENDEP (OS) (1)USAWECOM (60) Army Dep (2) except
USAMICOM (2) Lexington (3)
USAMUCOM (2) Tooele (12)USAECOM (2) Letterkenny (IO)USAMOCOM (2) OrdDep (OS) (2)USASMCOM (1) USA Tml (1)
USATECOM (2) POE (1)
USAATBD (3) USAOSA
USAOCDA (2) Ord PC(IO)OS Base Comd (2) Arsenals (5)
MDW (2) Springfield Armory (5)LOGCOMD (2) Proc Dist (2)
NC;StateAG (3); Units _ same as Active Army except allowance is one copy to each unit.USA,?: Sameas Active Army except allowance is one copy to each unit.For explanation of abbreviations used. see AR 320-50.