Thermal_Power_Plant_2 Prepared by: NMG
21
Thermal_Power_Plant_2 Prepared by: NMG
description
Thermal_Power_Plant_2 Prepared by: NMG. We consider power cycles where the working fluid undergoes a phase change. The best example of this cycle is the steam power cycle where water (steam) is the working fluid. Carnot Vapor Cycle. The heat engine may be composed of the following components. - PowerPoint PPT Presentation
Transcript of Thermal_Power_Plant_2 Prepared by: NMG
Thermal_Power_Plant_2
Prepared by: NMG
2
We consider power cycles where the working fluid undergoes a phase change. The best example of this cycle is the steam power cycle where water (steam) is the working fluid.
Carnot Vapor Cycle
3
The heat engine may be composed of the following components.
The working fluid, steam (water), undergoes a thermodynamic cycle from 1-2-3-4-1. The cycle is shown on the following T-s diagram.
4
0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.00
100
200
300
400
500
600
700700
s [kJ/kg-K]
T [C
]
6000 kPa
100 kPa
Carnot Vapor Cycle Using Steam
1
2 3
4
The thermal efficiency of this cycle is given as
th Carnot net
in
out
in
L
H
WQ
TT
,
1
1Note the effect of TH and TL on th, Carnot.•The larger the TH the larger the th, Carnot
•The smaller the TL the larger the th, Carnot
Nimymech\CarnotCycle\shell.swf
5
To increase the thermal efficiency in any power cycle, we try to increase the maximum temperature at which heat is added.
Reasons why the Carnot cycle is not used:•Pumping process 1-2 requires the pumping of a mixture of saturated liquid and saturated vapor at state 1 and the delivery of a saturated liquid at state 2.•To superheat the steam to take advantage of a higher temperature, elaborate controls are required to keep TH constant while the steam expands and does work.
To resolve the difficulties associated with the Carnot cycle, the Rankine cycle was devised.
6
RANKINE CYCLE: THE IDEAL CYCLE FOR VAPOR POWER CYCLES
The simple ideal Rankine cycle.
7
Energy Analysis of the Ideal Rankine Cycle
The efficiency of power plants in the U.S. is often expressed in terms of heat rate, which is the amount of heat supplied, in Btu’s, to generate 1 kWh of electricity.
The thermal efficiency can be interpreted as the ratio of the area enclosed by the cycle on a T-s diagram to the area under the heat-addition process.
Steady-flow energy equation
nimymech\steamPowerPlant.swf
To increase system efficiency
1. Lower condenser pressureMust have at least 10°C DT between condenser and cooling water
or air temperature for effective heat transferWatch quality at exit to prevent turbine problems (shouldn’t go
less than about 88%)
2. Superheat the steam moreTmax ~ 620° due to metallurgical considerations
3. Increase boiler pressure (with same Tmax)Pmax ~ 30 Mpa
4. Reheat of steam
5. Regeneration
9
HOW CAN WE INCREASE THE EFFICIENCY OF THE RANKINE CYCLE?
The effect of lowering the condenser pressure on the ideal Rankine cycle.
The basic idea behind all the modifications to increase the thermal efficiencyof a power cycle is the same: Increase the average temperature at which heat is transferred to the working fluid in the boiler, or decrease the average temperature at which heat is rejected from the working fluid in the condenser.
Lowering the Condenser Pressure (Lowers Tlow,avg)
To take advantage of the increased efficiencies at low pressures, the condensers of steam power plants usually operate well below the atmospheric pressure. There is a lower limit to this pressure depending on the temperature of the cooling medium Side effect: Lowering the condenser pressure increases the moisture content of the steam at the final stages of the turbine.
Effect of Lowering Condenser Pressure on the Ideal Rankine cycle
11
The effect of superheating the steam to higher temperatures on the ideal Rankine cycle.
Superheating the Steam to High Temperatures (Increases Thigh,avg)
Both the net work and heat input increase as a result of superheating the steam to a higher temperature. The overall effect is an increase in thermal efficiency since the average temperature at which heat is added increases.Superheating to higher temperatures decreases the moisture content of the steam at the turbine exit, which is desirable.The temperature is limited by metallurgical considerations. Presently the highest steam temperature allowed at the turbine inlet is about 620°C.
12
Increasing the Boiler Pressure (Increases Thigh,avg)
The effect of increasing the boiler pressure on the ideal Rankine cycle.
For a fixed turbine inlet temperature, the cycle shifts to the left and the moisture content of steam at the turbine exit increases. This side effect can be corrected by reheating the steam.
A supercritical Rankine cycle.
Today many modern steam power plants operate at supercritical pressures (P > 22.06 MPa) and have thermal efficiencies of about 40% for fossil-fuel plants and 34% for nuclear plants.
Effect of Increasing Boiler Pressure on the Ideal Rankine cycle
Reheat Cycle• Allows us to increase boiler pressure without problems
of low quality at turbine exit
15
Rankine Cycle with ReheatComponent Process First Law Result Boiler Const. P qin = (h3 - h2) + (h5 -
h4) Turbine Isentropic wout = (h3 - h4) + (h5 -
h6) Condenser Const. P qout = (h6 - h1) Pump Isentropic win = (h2 - h1) = v1(P2
- P1)
The thermal efficiency is given by
thnet
in
wqh h h h h h
h h h hh h
h h h h
( - ) + ( - ) - ( - )( - ) + ( - )
( - ) + ( - )
3 4 5 6 2 1
3 2 5 4
6 1
3 2 5 4
1
Nimymech\RankineCycleReheating\Source\shell.swfNimymech\Animation\ReheatCycle.swf
16
THE IDEAL REHEAT RANKINE CYCLEHow can we take advantage of the increased efficiencies at higher boiler pressures without facing the problem of excessive moisture at the final stages of the turbine?1. Superheat the steam to very high temperatures. It is limited metallurgically.2. Expand the steam in the turbine in two stages, and reheat it in between (reheat)
The ideal reheat Rankine cycle.
Regeneration• Preheats steam entering boiler using a feedwater heater,
improving efficiency– Also deaerates the fluid and reduces large volume flow
rates at turbine exit.
0 2 4 6 8 10 12120
100
200
300
400
500
600
s [kJ/kg-K]
T [C
] 3000 kPa
500 kPa
10 kPa
Rankine Steam Power Cycle with an Open Feedwater Heater
1
2 3
4
5
6
7
nimymech\openFWH.swf
nimymech\RankineCycleRegeneration\shell.swf
20
Open Feedwater Heaters
The ideal regenerative Rankine cycle with an open feedwater heater.
An open (or direct-contact) feedwater heater is basically a mixing chamber, where the steam extracted from the turbine mixes with the feedwater exiting the pump. Ideally, the mixture leaves the heater as a saturated liquid at the heater pressure.
Reheat
Nimymech\RankineCycleReheating\Source\shell.swf
Nimymech\Animation\ReheatCycle.swf
Simple Rankine Cyclenimymech\steamPowerPlant.swf
Regenerationnimymech\openFWH.swf
nimymech\RankineCycleRegeneration\shell.swf
