THE ULTIMATE IN FLOOR PREPARATIONcemimaxaustralia.com/wp-content/uploads/2019/06/... · Dispersion...
Transcript of THE ULTIMATE IN FLOOR PREPARATIONcemimaxaustralia.com/wp-content/uploads/2019/06/... · Dispersion...
THE ULTIMATE INFLOOR PREPARATION
Low emission, multi-purpose dispersion primer for existing surfaces
DP60 DP80
Dispersion Primer with a wide range of applications, for interior and exterior use, providing overlayment compound DL10 or DL59 is applied within drying time of primer. Not to be left exposed to the elements for more than 2 hours.
DESCRIPTION
SUITABLE FOR
PRODUCT PROPERTIES
Use on surfaces with well-bonded, waterproof adhesive and smoothing compound residues
Ready to useExcellent bondRapid dryingHigh coverageSolvent-free
BINDERSModified styrene-acrylate copolymers, wetting and defoaming agents, preservatives and water
TECHNICAL DATAUnder normal conditions 20°CPacking: Plastic BucketPackaging Size: 20kg or 5kgShelf-life: 12 monthsApplication Temp Range: +5°C - 35°CConsumption: Approx 12m²/1 LitreDrying time: 4-6 hoursTouch Dry: 15-20mins
One component, low emission, multipurpose dispersion primer with carbon fibre technology for non absorbency substrates
DESCRIPTIONDispersion primer low emission, film forming primer for use over non-absorbent surfaces including non-water soluble adhesive residues. The product cannot be diluted with water and for interior and exterior use, providing overlayment compound DL10 or DL59 is applied within drying time of primer. Not to be left exposed to the elements for more than 2 hours.
SUITABLE FOR• Use on non-absorbent substrates, very suitable for existing surfaces in need of refurbishment, such as well-bonded and non-water-soluble adhesive residues including cutback adhesive.• Dense & smooth surfaces, on soundly bonded ceramic and natural stone tiles, terrazzo, water resistant coatings, epoxy coatings or metal surfaces
Ready to useExcellent bondVery fast dryingCarbon fibre technologySolvent-free
PRODUCT PROPERTIES• ••••
• ••••
COMPOSITIONModified styrene-acrylate copolymers, wetting and defoaming agents, preservatives and carbon fibre
Under normal conditions 20°CPacking: Plastic BucketPackaging Size: 20kg or 5kgShelf-life: 12 monthsApplication Temp Range: +5°C - 35°CConsumption: Approx 12m²/1 LitreDrying time: Approx 1 hourTouch Dry: 15-20mins
TECHNICAL DATA
PRIMER NON-POROUS PRIMER
DL10Levelling cement flooring compound to economically bulk fill and raise floors
DESCRIPTIONDL10 is an advanced cement and polymer-based levelling compound with special aggregate. DL10 is formulated with high flow performance for levelling work on the installation of thick layers. DL10 is very suitable for quick-setting preparation solutions and also can be used as a fast set screed with low ratio water mixing.
Plastic, dry cement mortar with finely graded fillers. When mixed with water, produces a hydraulic-setting smoothing compound with good flow properties and high coverage.
PRODUCT PROPERTIES/BENEFITS
Easy applicationQuick settingSuperior flow — fast applicationCan be used as a fast set screedHigh-depth limitation 1.5mm to 150mmCompatible with other cemimax levelling compoundsFor Interior and Exterior useSuitable for Radiant Floor Heating systems
• •••••••TECHNICAL DATA
COMPOSITION
Compressive StrengthAfter 1 day approx. 15MPaAfter 7 days approx. 20MPaAfter 28 days approx. 30MPaTensile Bending StrengthAfter 1 day approx. 5MPaAfter 7 days approx. 7MPaAfter 28 days approx. 8MPaPack-size: 20kg/bagShelf-life: 6-12 monthsCoverage: Approximately 6m² at 3mm thickWorking time: 15-25minsDrying time: 10-30mins
Special cements, mineral fillers, polyvinyl-acetate-copolymers, flow agents and additives.
BULK FILLING COMPOUND
General - purpose, Self-smoothing and leveling compound
DL55
DL55 is an advanced cement and polymer based levelling and smoothing compound. DL55 is formulated for experienced commercial contractors to smooth and level large commercial and retail areas. Once dry it is suitable for the application of vinyl, carpet and tile floor finishes. Unlike normal hydration levellers, DL55 will harden and dry at temperatures down to 10°C.
DESCRIPTION
PRODUCT PROPERTIES/BENEFITS
COMPOSITION
Plastic dry cement mortar with finely graded fillers. When mixed with water, produces a hydraulic-setting smoothing compound with good flow properties and high coverage.
Super smooth - requires no sandingVersatile - apply 1.5mm to 40mm in one applicationRapid hardening - walkable from 2 hoursSuperior flow - fast applicationFlexible - hand mix or pump applicationFor Interior useSuitable for Radiant Floor Heating systems
TECHNICAL DATACompressive StrengthAfter 1 day approx. 15MPaAfter 7 days approx. 25MPaAfter 28 days approx. 35MPaTensile Bending StrengthAfter 1 day approx. 5MPaAfter 7 days approx. 7MPaAfter 28 days approx. 10MPaColor: GreyWater / compound ratio: 0.22/1Working time: 20-30 minutesPack-size: 20kg/bagShelf-life: 6-12 monthsCoverage: Covers approx. 6m² at 3mm thickDrying time: 2hrs
• ••••••
Special cements, mineral fillers, polyvinyl-acetate-copolymers, flow agents and additives.
LEVELLING COMPOUND
DL59Self-smoothing and levelling compound as surface overlay floors
DESCRIPTIONDL59 is a cement based levelling compound with very high compressive strength to C40. DL59 is especially suitable for high traffic, heavy wear location. DL59 is especially used as overlays for polished concrete floors.
PRODUCT PROPERTIES/BENEFITS:Plastic dry cement mortar with finely graded fillers. When mixed with water, produces a hydraulic-setting smoothing compound with good flow properties and high coverage.
Special cements, mineral fillers, polyvinyl-acetate-copolymers, flow agents and additives.Super smooth - requires no sandingExtremely high flexible strength - 60%Versatile - apply 1.5mm to 40mm in one applicationRapid hardening - walkable from 2 hoursSuperior flow - fast applicationFlexible - hand mix or pump applicationCan be polishedFor Interior and Exterior useSuitable for Radiant Floor Heating systemsPigments can be added for colourAggregates can be added for exposed stone effect
COMPOSITION•
•••••••••••
Compressive StrengthAfter 1 day approx. 15MPaAfter 7 days approx. 25MPaAfter 28 days approx. 40MPaTensile Bending StrengthAfter 1 day approx. 5MPaAfter 7 days approx. 7MPaAfter 28 days approx. 10MPaPack-size: 20kg/bagShelf-life: 6-12 monthsCoverage: Approximately 6m² at 3mm thickWorking time: 20-30 minsDrying time: 2hrs
TECHNICAL DATA
DL99Self-smoothing and levelling compound with terrazzo effect
DESCRIPTIONDL99 terrazzo is a cement based levelling compound designed with terrazzo aggregate component. DL99 provides a decorative surface with different colour options with aggregates The aggregate are pre-mixed in bag for easy application as a leveller. Also available for custom colours and styles, allow a 3-6 week wait for custom orders.
Plastic dry cement mortar with finely graded fillers. When mixed with water, produces a hydraulic-setting smoothing compound with good flow properties and high coverage.
PRODUCT PROPERTIES/BENEFITS
• ••••••
Super smoothExtremely high strength of compressive and bendingSuperior flow — fast applicationCan be polished, sealed and honedDifferent types of terrazzo aggregates availableFor interior and outdoor useSuitable for Radiant Floor Heating systems
Special cements, mineral fillers, polyvinyl-acetate-copolymers flow agents and additives.
TECHNICAL DATACompressive StrengthAfter 1 day approx. 15MPaAfter 7 days approx. 25MPaAfter 28 days approx. 40MPaTensile Bending StrengthAfter 1 day approx. 5MPaAfter 7 days approx. 7MPaAfter 28 days approx. 10MPaPack-size: 20kg/bagShelf-life: 6-12 monthsWorking time: 20-30 minsDrying time: 2hrs
COMPOSITION
THICKNESSDL99 is recommended to be applied from 10mm thickness for polishing
INDOOR/OUTDOOR LEVELLING COMPOUND DECORATIVE FLOOR FINISH
Patching compound for repair, filling and patching
PP3 PP5
PP3 is an advanced cement and polymer-based patching compound for repair, filling and patching up to 13mm depth. Can be used on a variety of substrates prior to installation of most flooring products. Priming is not required for most applications.
DESCRIPTION
PRODUCT PROPERTIES/BENEFITS
COMPOSITION
Plastic dry cement mortar with finely graded fillers. When mixed with water, produces a hydraulic-setting smoothing compound.
New or old cement levelling compoundsExisting substrates with well-bonded, non-water-soluble adhesive residuesLarge and small format tile and natural stonePlywood underlaymentAll standard slabs, concrete or other substrate typesHeavy traffic areas in domestic & commercial applicationsRadiant floor heating systems
TECHNICAL DATAPack-size: 5kg bagShelf-life: 6-12 monthsCoverage: Approx. 2.8m2 at 3mm per bagWater mixing: Approx. 1:2 (water : powder)Dry time: After approx. 10 min. for walked onAfter approx. 15 min. for floor coveringAfter approx. 12 hours for wood flooring
Cementitious, Rapid Repair Patching and Smoothing Compound
DESCRIPTIONPP5 is an advanced cement and polymer mix that is highly versatile, rapid drying patching compound. Its fine aggregates allow it to be installed from a feather edge up to a high fill depth in one application. Superior bonding allows it to be applied over existing concrete, well-bonded flooring, properly prepared non-water soluble adhesive, well-bonded gypsum, all without having to use primer in most applications.
PRODUCT PROPERTIES/BENEFITS:High depth limitationFast Setting - within 15 minutesSuperior Bonding - Eliminates the need for a primer in most applicationsLow to No VOC - Healthy indoor air quality
SUITABLE SUBSTRATE CONDITIONS
• ••
•
• •••••••
Packaging: 20kg paper bagStorage: 6-12 monthsWater ratio: 100:12.5 (powder : water ratio)Working Time: 10-15 minutesDry Time: Moisture Sensitive Flooring 15 MinutesDry Time: High depth installation from 15-30 mins
TECHNICAL DATA
SUITABLE FOR
Fast dry formulaHigh strengthVery fine aggregatesVariable water rangeSmooth surface finishExcellent absorbencyVersatile product
• ••••••
Special cements, mineral fillers, polyvinyl-acetate-copolymers, and additives.
Installed over all existing flooring that is structurally sound, thoroughly clean and free of polishes, waxes, grease, asphalt and any other contaminant that might act as a bond breaker. Can be applied over properly prepared and installed epoxy moisture barriers and PU vapor retarders. For use where Radiant Heat systems are being installed. Existing surfaces in need of refurbishment, such as well bonded, non-water soluble adhesive residues including cutbackFor Interior and Exterior use
FEATHER EDGE SMOOTHING COMPOUND
•
•
••
•
RAPID/RAMPING COMPOUND
A600Water-based dispersion adhesive for linoleum floor coverings on absorbent substrates. Wet adhesives with a short drying time. For interior use.
Very high initial tack and final bonding strengthBonding layer has durable resilienceLow drying timeSolvent-freeLow VOC
PRODUCT PROPERTIES
TECHNICAL DATAUnder normal conditions at 20°CPackaging: 15kg Plastic drumShelf-life: Min. 12 monthsColour: Cream-whiteWorking temperature: +5°C - 35°CConsumption: 3.75m²/1 LitresDrying time: 30 minutesSet to traffic: After 24hoursFinal strength: After 3 daysOpen time: 5-30mins
SUITABLE FORLinoleum floor coverings in sheets and panelsIn residential and commercial areas
• •
• ••••
BINDERS:Modified polyacrylate-copolymers with bond strengthening resins.
A350High strength adhesive for resilient floor coveringsDESCRIPTIONDispersion adhesive for resilient synthetic floor and wall cover-ings in interior areas.
SUITABLE FORRubber flooring sheet, PVC sport flooring sheet, vinyl tile and cushioned vinyl coverings, including those with textile fleece backings.
PRODUCT PROPERTIES• •••
Good water resistance, excellent bonding strengthVery high initial tack and final bonding strengthEasy application, high coverage rateLow VOC
BINDERS:Modified polyacrylate-copolymers with bond strengthening resins.
TECHNICAL DATAUnder normal conditions 20°CPackaging: 5kg Plastic drumShelf-life: Min. 12 monthsColour: Cream-whiteWorking temperature: +5°C - 35°CDry time: 30minsConsumption: 3.75m²/1 LitresOpen time: 5-30 minutesWorking time: 1-2 hoursSet to traffic: After 24-48 hoursFinal strength: After 5-7 days
RESILIENT FLOOR ADHESIVE LINOLEUM ADHESIVE
A2000Very high strength for resilient floor coverings
DESCRIPTIONDispersion adhesive for resilient synthetic floor and wall coverings in interior areas.
Stable quality Bonding, layer has durable resilienceGood water resistance, excellent bonding strengthVery high initial tack and final bonding strengthEasy application, high coverage rateLow VOC
PRODUCT PROPERTIES/BENEFITS• ••••
TECHNICAL DATAUnder normal conditions at 20°CPackaging: 15kg Plastic drumShelf-life: Min. 12 monthsColour: Cream-whiteWorking temperature: +5°C - 35°CConsumption: 3.75m²/1 LitresOpen time: 5-30 minutesWorking time: 1-2 hoursSet to traffic: After 24-48 hoursFinal strength: After 5-7 days
SUITABLE FORRubber flooring sheet, PVC sport flooring sheet, vinyl tile and cushioned vinyl coverings, including those with textile fleece backings.
BINDERS:Modified polyacrylate-copolymers with bond strengthening resins.
WALL COVERINGS ADHESIVE
DP400Two component solvent free Epoxy resin primer used to improve the strength of the substrates. It can also be used as crack repair for concrete, in cement-based subfloors.
DESCRIPTIONCemimax DP400 is a 2-component solvent free Epoxy resin primer used to improving the strength of the substrates. It can be used as crack repair for concrete, cement-based subfloors. It can also be used as moisture vapor retarder for concrete substrates with high residual moisture.
SUITABLE FORUse on substrates with low damp conditions, on ceramic, terrazzo, stone subfloors, surfaces with well-bonded, waterproof adhesive and smoothing compound residues. Use on cracked substrates as a repair resin
PRODUCT PROPERTIESBridges cracksMoisture barrier controlIncreases the strength of the substrateVery good resistance to chemicalsExcellent covering and filling capacitySolvent free
• •••••
TECHNICAL DATA
COMPOSITIONPolyamine-hardened epoxy resin.
Under normal conditions 20°CPacking: Plastic BucketPackaging Size: 15kg setShelf-life: 12 monthsColour: Lightish YellowWorking temperature: +5°C - 35°CConsumption: Approx. 0.7m²/1 LitreDrying time: 12-24hoursPot life: 25-30minutesMixing ratio: A: B=1:2Working time: 2 hours
EPOXY RESIN PRIMER
Sydney Head Office:2/27 Grosvenor StNeutral Bay, NSW 2089Sydney Warehouse: Gate | Building 2, Door 2F Loftus RdYennora, NSW 2161Melbourne Warehouse: Lot 1218, 3-7 Claremont St,South Yarra, VIC 3141
Phone: John Titus 0488 203 525Email: [email protected] www.cemimaxaustralia.com