The Original Danish Oil
1
For interior and exterior use Natural, low lustre finish Danish Oil The Original Ideal for Tables Chairs Wooden Furniture Doors Dado Rails Wood Panelling Window Frames/Sills Wooden Worktops 500ml Rustins – producing expert wood finishes since 1924. SHAKE WELL BEFORE USE Danish Oil contains tung oil and other special ingredients which penetrate deep into all types of timber, drying to a hard, durable and water resistant seal. The oil primes, seals and finishes all woods, including oak, teak, mahogany and pine. It does not leave a surface film to chip or scratch. May also be used as a primer before painting and varnishing. Excellent for use on all turned work including wooden handles of kitchen equipment and tops of storage jars. Rustins Danish Oil conforms to The Articles in Contact with Food Regulations and to the Toys (Safety) Regulations 1995, BS:EN71 Part 3. We recommend Rustins Floor Oil for interior floors. Preparation The surface must be clean, sanded smooth and free from contaminants like wax and dirt. For best results apply to dry, sound wood with a moisture content between 12-20%. Do not apply to green timber. Oily woods (e.g. Teak, Iroko) should be cleaned thoroughly with white spirit before application of Danish Oil. Exterior wood requires a minimum of 3 coats applied liberally and not wiped off. To improve the penetration and durability dilute the first coat 20% with white spirit. If applying Danish Oil to veneered doors, it is advisable to check with the door manufacturer before proceeding. Exterior wood will require regular re- oiling, especially on horizontal surfaces and in very exposed conditions. Oak and softwoods are prone to weather staining caused by moisture activating mould spores present naturally in the wood. It is advisable to treat the wood with Rustins Advanced Clear Wood Preserver before applying Danish Oil. Extra coats of Danish Oil are required to effectively seal these timbers. If in doubt use Rustins Outdoor Clear Varnish or Rustins Flexterior. Bare wood may be dyed if required with Rustins Wood Dye. If a natural open grain is not required such as with oak, then use Rustins Grain Filler prior to oiling. Application Using a clean soft cloth or brush apply liberally, then wipe off the excess after a few minutes. For a superior smooth finish the final coat may be applied using a plastic scouring pad, rubbing in the direction of the grain, wiping away the surplus with a soft cloth or paper towels. New or bare wood should be oiled 3 times initially. Re-Coating Time Allow 4 to 8 hours between applications depending on the temperature and humidity. Maintenance When applying to previously oiled wood, the surface should be cleaned and any wax removed using white spirit or Rustins Surface Cleaner. Wipe away the solution formed with clean paper towels, prior to re-oiling. If the surface develops a slight gloss, this can be removed by rubbing with grade 00 or 000 steel wool and either wax polish or white spirit finishing off with a soft cloth. If compatibility with a previously coated surface is not known, then test by applying to a small area first. Coverage 1 litre covers approximately 14 square metres per coat depending on the absorbency of the wood. Cleaning Remove excess product from brushes before cleaning whilst wet with white spirit or Rustins Brush Cleaner. Hard brushes can be cleaned with Rustins Brush Restorer. Important Rags used for oiling must be laid out flat to dry or destroyed, otherwise they may catch fire due to spontaneous combustion. Disposal (pollution prevention) Some local authorities have special facilities for disposal of waste paints/varnishes/coatings. Do not empty product into drains or watercourses. Storage Store in a cool dry place with lid tightly closed. HEALTH AND SAFETY: Contains cobalt 6, 2-octyl-2h-isothiazol-3-one. May produce an allergic reaction. Flammable liquid and vapour. May cause genetic defects. May cause cancer. Keep out of reach of children. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use explosion-proof electrical / ventilating / lighting /... equipment. Wear protective gloves and eye protection. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. IF exposed or concerned: Get medical advice/attention. UFI: MP2N-QRQC-5F0Y-EMA0 Please refer to Product Data Sheet for full information at www.rustins.co.uk For information on Rustins’ products visit our website at www.rustins.co.uk or contact us at Rustins Ltd, Waterloo Road, London, NW2 7TX United Kingdom [email protected] Tel: +44 (0)20 8450 4666 ROI: Excellence Ltd, 43 Grange Parade, Dublin D13 Y860 Ireland. Tel: +353 1 - 832 3300 EU Limit value for this product (CAT A/f): 700g/l (2010). This product contains max 650g/l VOC. Made in UK DANGER
Transcript of The Original Danish Oil
For interior and exterior use
Natural, low lustre finish Danish OilThe Original
Ideal for
Tables
Chairs
WoodenFurniture
Doors
Dado Rails
WoodPanelling
WindowFrames/Sills
WoodenWorktops
500ml
Rustins – producingexpert wood
finishes since 1924.
SHAKE WELL BEFORE USEDanish Oil contains tung oil and other special ingredients which penetrate deep into alltypes of timber, drying to a hard, durable and water resistant seal. The oil primes, sealsand finishes all woods, including oak, teak, mahogany and pine. It does not leave asurface film to chip or scratch. May also be used as a primer before painting andvarnishing. Excellent for use on all turned work including wooden handles of kitchenequipment and tops of storage jars. Rustins Danish Oil conforms to The Articles inContact with Food Regulations and to the Toys (Safety) Regulations 1995, BS:EN71 Part 3. We recommend Rustins Floor Oil for interior floors.
PreparationThe surface must be clean, sanded smooth andfree from contaminants like wax and dirt. For bestresults apply to dry, sound wood with a moisturecontent between 12-20%. Do not apply to greentimber. Oily woods (e.g. Teak, Iroko) should becleaned thoroughly with white spirit beforeapplication of Danish Oil. Exterior wood requires aminimum of 3 coats applied liberally and not wipedoff. To improve the penetration and durability dilutethe first coat 20% with white spirit. If applyingDanish Oil to veneered doors, it is advisable tocheck with the door manufacturer beforeproceeding. Exterior wood will require regular re-oiling, especially on horizontal surfaces and in veryexposed conditions. Oak and softwoods are proneto weather staining caused by moisture activatingmould spores present naturally in the wood. It isadvisable to treat the wood with Rustins AdvancedClear Wood Preserver before applying Danish Oil.Extra coats of Danish Oil are required to effectivelyseal these timbers. If in doubt use Rustins OutdoorClear Varnish or Rustins Flexterior. Bare wood maybe dyed if required with Rustins Wood Dye. If anatural open grain is not required such as withoak, then use Rustins Grain Filler prior to oiling.
ApplicationUsing a clean soft cloth or brush apply liberally,then wipe off the excess after a few minutes. For asuperior smooth finish the final coat may be appliedusing a plastic scouring pad, rubbing in thedirection of the grain, wiping away the surplus witha soft cloth or paper towels. New or bare woodshould be oiled 3 times initially.
Re-Coating TimeAllow 4 to 8 hours between applications dependingon the temperature and humidity.
MaintenanceWhen applying to previously oiled wood, the surfaceshould be cleaned and any wax removed usingwhite spirit or Rustins Surface Cleaner. Wipe awaythe solution formed with clean paper towels, priorto re-oiling. If the surface develops a slight gloss,this can be removed by rubbing with grade 00 or000 steel wool and either wax polish or white spiritfinishing off with a soft cloth.If compatibility with a previously coated surface is not known, then test by applying to a small area first.
Coverage1 litre covers approximately 14 square metresper coat depending on the absorbency of thewood.
CleaningRemove excess product from brushes beforecleaning whilst wet with white spirit or RustinsBrush Cleaner. Hard brushes can be cleaned withRustins Brush Restorer.
ImportantRags used for oiling must be laid out flat to dry ordestroyed, otherwise they may catch fire due tospontaneous combustion.
Disposal (pollutionprevention)
Some local authorities have special facilities fordisposal of waste paints/varnishes/coatings. Donot empty product into drains or watercourses.
StorageStore in a cool dry place with lid tightly closed.
HEALTH AND SAFETY: Contains cobalt 6, 2-octyl-2h-isothiazol-3-one.May produce an allergic reaction. Flammableliquid and vapour. May cause genetic defects.May cause cancer. Keep out of reach ofchildren. Keep away from heat, hot surfaces,sparks, open flames and other ignition sources.No smoking. Use explosion-proof electrical /ventilating / lighting /... equipment. Wear protective gloves and eye protection. IF ON SKIN (or hair): Take off immediately allcontaminated clothing. Rinse skin with water. IF exposed or concerned: Get medical advice/attention.UFI: MP2N-QRQC-5F0Y-EMA0Please refer to Product Data Sheet for full information atwww.rustins.co.uk
For information on Rustins’ products visit our website atwww.rustins.co.uk or contact us at Rustins Ltd, WaterlooRoad, London, NW2 7TX United [email protected] Tel: +44 (0)20 8450 4666ROI: Excellence Ltd, 43 Grange Parade, Dublin D13 Y860 Ireland. Tel: +353 1 - 832 3300
EU Limit value for thisproduct (CAT A/f): 700g/l (2010).
This product containsmax 650g/l VOC.
Made in UK
DANGER
20210608_LAB_DanishOil 500mlHUBER.qxp_0213814 Teak Oil 500ml 08/06/2021 13:23 Page 1
