The G-COAT 415 provides safe and desired thickness and quality - … · 2016. 10. 21. · The...

2
The G-COAT 415 provides safe and rapid coating on both sides, in any desired thickness and quality G-COAT 415 Grünig-Interscreen AG Ringgenmatt 14 CH-3150 Schwarzenburg Switzerland Phone +41 31 734 260 0 Fax +41 31 734 260 1 www.grunig.ch [email protected]

Transcript of The G-COAT 415 provides safe and desired thickness and quality - … · 2016. 10. 21. · The...

Page 1: The G-COAT 415 provides safe and desired thickness and quality - … · 2016. 10. 21. · The G-COAT 415 provides safe and rapid coating on both sides, in any desired thickness and

The G-COAT 415 provides safe and rapid coating on both sides, in any desired thickness and quality

G-C

OA

T 4

15

Grünig-Interscreen AGRinggenmatt 14CH-3150 SchwarzenburgSwitzerland

Phone +41 31 734 260 0Fax +41 31 734 260 [email protected]

Page 2: The G-COAT 415 provides safe and desired thickness and quality - … · 2016. 10. 21. · The G-COAT 415 provides safe and rapid coating on both sides, in any desired thickness and

G-COAT 415Automatic coating machine MODULAR

Particular features

■ Advantageous introduction into the automatic double-sided coating technique.

■ Safe reproductibility of the coating results guaranteed for direct coating process wet-on-wet (tolerance +/- 1µ).

■ Modular construction method in various exe-cution models (front or side loader, IN-LINE configuration).

■ Uncomplicated operation and introduction of all the parameters via a Touch-Screen Terminal.

■ 50 freely definable programs are available.■ Length measuring system for detecting the screen

sizes and controlling the coating position.■ The separate actuation of both coating troughs

allows to coat the mesh from the squeegee side, from the print side or from both sides.

■ Extremely silent operation of the coating carriage.■ Toothed belt drive unit with sliding guide made

of special synthetic material, requiring just a minimum of maintenance.

Version A10■ Standard execution, front loader.

Version A20■ Front loader with raised floor base for an ergono-

mic screen handling.

Version A30L■ Loading of the screens from the left side, with

upper and lower pneumatic screen fasteners.

Version A30R■ Loading of the screens from the right side, with

upper and lower pneumatic screen fasteners.

Version A40■ IN-LINE execution for integration into the G-LINE

system from Grünig.

Option MD■ The option „Maintenance Diagnostic“ allows im-

mediate error analysis and assistance via remote maintenance by the Grünig support team.

Option R■ Automatic cleaning of the coating edge by means

of moistened wiper rolls which wipe off the remai-ning emulsion from both sides. The wiper rolls are automatically moistened and washed.

Option S Pneumatic screen supports on top for an optimal

fastening of the screens.

Option T■ The automatic hot-air dryer allows an intermediate

drying during layer build-up. It is equipped with its own drive unit and acts from the print side, inde-pendeently from the spraying carriage. The speed and the number of moves can be programmed.

Option Z■ Additional pneumatic screen fastening device for

simultaneous treatment of two screens.

Screen frame size SB Screen width mm 1000-2500 SH Screen height mm 1250-5000 Frame profile height mm 30-195 Frame profile thickness mm 10 - 60 Size Width mm SB + 1200 Height mm SH + 800 Depth mm 630

Energy supply Voltage V 3x400 + N + PE 3x220 PE Frequency Hz 50/60

Compressed air Connection value bar 6 Air consumption lit/min 10

Permanent sound - pressure level dB (A) < 70

All measurements in mm The machine is in compli-ance with the EU machinery directives (CE conformity)

Technical data subject to change without notice

February 2011

at least 500/19“SB + 1150/45“

SH

580/

23“

SH

+ 7

70/3

0“

SB

at least 200/8“

min

. 300

/12“

Touch-Screen Terminal

Option R

Option T

Coating trough

SB

SH

SH

800

SB + 1200min.500 min.200

630

min

300