The California State University - Faculty...

1

The California State University

O f f i c e o f t h e C h a n c e l l o r - S W R L L o c a t i o n Computer Aided Design (CAD) - GuidelinesEdition Date: June 30, 1995Revision Date: April 21, 1998

2

This Page intentionally left blank.

3

Table Of ContentsOverview 5

1.0 General Requirements 5

2.0 Required Documentation 62.1 Diskette Labeling 62.2 File Description 8

3.0 Required Data 93.1 File Types 9

3.1.1 Text Files 93.1.2 Drawing Files 9

3.2 File Information 93.3 File Format 103.4 File Size And Organization 103.5 Copy And Compression Format 103.6 Reference Files 103.7 Document File Format 103.8 File Naming 11

4.0 Drawing Formats & Graphics 134.1 Standard Coordinate System 134.2 Prototype Drawing Files 134.3 Standard Sheet Sizes And Formats 134.4 Graphics 13

4.4.1 Text 134.4.2 Special Entity Requirements 14

4.5 Dimensioning 144.5 Fill And Hatch Patterns 154.6 Line Weights And Pen Assignments 15

5.0 Layering 165.1 Layer Guidelines By Discipline 17

5.1.1 Architectural Layer Guidelines 185.1.2 Structural Layer Guidelines 205.1.3 Mechanical Layer Guidelines 225.1.4 Plumbing Layer Guidelines 245.1.5 Fire Protection Systems Layer Guidelines 255.1.6 Electrical Layer Guidelines 265.1.7 Civil Layer Guidelines 275.1.8 Boundary Survey Layer Guidelines 285.1.9 Topographic Plans Layer Guidelines 295.1.10 Landscape Layer Guidelines 305.1.11 Campus Master Plan Layer Guidelines 315.1.12 Utility Infrastructure Layer Guidelines 32

5.2 Minor Group Abbreviations 345.3 Modifiers And User Definitions 37

Appendix: S.0 Prototype Submittals 41S.0.1 Typical Drawing File Set Up 42

Appendix: S.1 Small Building Project Prototype Submittal 43

Appendix: S.2 Campus Utility Map Prototype Submittal 53

Appendix: S.3 Major Building Project Prototype Submittal 61

4

This Page intentionally left blank.

5

OVERVIEW

This computer aided design (CAD) guideline is for use on all of the California State University(CSU) Campuses’. These standards have been developed to serve as a template for thedevelopment of contractually required electronic data submittals to the California State University.Any deviations from these standards are to be approved in writing in advance by the University.Consultants shall contact Physical Planning & Development's (PP&D’s) CAD resources for themost current release and amendments prior to the commencement of any work.

1.0 GENERAL REQUIREMENTS

All information described in section 3.0 is to be included in the electronic data deliverables. Anyadditional files are to be excluded from the deliverable package unless otherwise directed by theUniversity. All deliverables are to be provided on DOS 3 1/2” DSHD Diskettes (1.44 MB).

All files are to be transferred to diskettes using the DOS copy command with DOS version 3.3 orlater. Refer to section 3.5 for copy and compression formats.

All drawings files will be saved in AutoCad version 12.0. No other formats or versions will beacceptable.

The submittor is responsible for archiving the electronic data until final written acceptance fromthe University has been issued. Electronic data deliverables are required with all major submittalsas past schematic design unless otherwise directed by Contract Agreements.

6

2.0 REQUIRED DOCUMENTATION

The electronic data deliverable package will include 3 1/2” diskettes with labels and 8 1/2”x 11”hard copy print out of the file descriptions.

2.1 DISKETTE LABELING

All diskettes are to be labeled as follows:

CAMPUS: Campus for which the project is intended for. Specify satellitelocation if applicable.

DATE: The date the data was delivered to the campus for final acceptance.

PROJECT: Title of the project.

BLDG NUMBERS: Two digit building number identified by the campus specific to theproject.

AUTOCAD VERSION : Auto CAD version.

DOS VERSION: DOS utility version.

COMPANY: Name of consultant to the campus.

PHONE NUMBER: Phone number of consultant.

DISKETTE NUMBER: Diskette number. Deliverables diskette are to be numbered incoordination with File Descriptions.

FILES: List of drawing files included on diskette.

Individual specification sections are not to be listed on the diskette label. Limit file listing on textfiles to either “SPECIFICATIONS” of “FILE DESCRIPTIONS”. See Examples below.

7

2.1 DISKETTE LABELING Continued

CSU Long Beach 1/1/93Business Science Bldg. #23Auto Cad 12.0 Dos 5.0A1 Architects, Inc. (310) 555-1000Specifications Disk #01

CSU Long Beach 1/1/93Business Science Bldg. #23Auto Cad 12.0 Dos 5.0A1 Architects, Inc. (310) 555-1000Drawing Files: Disk #02A230A201.DWG A230A202.DWGA230A203.DWG A230A204.DWGA230A301.DWG A230A302.DWG

A230A401.DWG A230A501.DWG

Example A

Diskette labeling example for typical text files.

Example B

Diskette labeling example for typical drawing files.

8

2.2 FILE DESCRIPTION

Each diskette is to be accompanied by a file description for each file on an 8 1/2”x11” hard copyprint out and a text file in ASCII format. Master files using reference files are to itemize allapplicable reference files and layers. Each file description is to include the following information:

CAMPUSPROJECTBUILDING NUMBERDATECONSULTING COMPANYADDRESS & PHONE NUMBERPROJECT MANAGERFILE NAMELAYERING OR SECTIONSREFERENCE FIELD w/LAYERS (only for master files)REMARKS

See example below.

CALIFORNIA STATE UNIVERSITYELECTRONIC DATA - FILE DESCRIPTION

Prepared for:CSU, Long BeachBusiness Science Bldg. -#231/1/93

Remarks:Paper space and model space hasbeen used on this file format.

Prepared By:A1 Architects, Inc.1000 Main StreetLos Angeles, CA 90000Jon Doe, Project Manager(310) 555-1000

The following layers and reference files are included in file A23AF01.DWG

Primary Layers #1 Ref. FileA230EF02.DWG

#2 Ref. FileA230FF03.DWG

#3 Ref. FileA230SF04.DWG

A-FLOR E-FLOR F-FIRE S-FLORA-FURN E-LITE F-HALN S-PCOL

A-GLAZ E-PCON S-PSFRA-PARE E-LITEA-PEQM

9

3.0 REQUIRED DATA

3.1 FILE TYPES

Both text and graphic type files will be included in the electronic data deliverables. Text files andGraphic files are not to be mixed on the same diskette.

3.1.1 TEXT FILES

The only types of text files to be included in the deliverables are File Descriptions andSpecifications unless otherwise directed by the University. Both file types are to be saved in anASCII text format using DOS version 3.3 or later. No other files formats will be acceptable fortext files.

3.1.2 DRAWING FILES

The only types of drawing files to be included in the deliverables are Document Files and MasterFiles unless otherwise directed by the University.

A Document File is a single plot ready file. They are to be completely formatted and plot-ready.One Document file is required for each drawing sheet included in the construction or map set.

Master Files are single files that may rely on other reference files. These would consist of overallmaster plan that include a comprehensive format of information. Refer to section 3.6 for directionon reference files.

3.2 FILE INFORMATION

All information included in hard copy submittals are to included in electronic data deliverables.

If blocks and cells are used in the documents, then they are to be consistent throughout withoutdeviation. For example, if fixture “A” is used in a block form, then all locations where fixture ‘A”is shown shall be of the same block.

No raster images will be acceptable. All graphic images in the drawing files are to be vectorizedimages.

Drawings relying on reference files are to include a list of dependent reference files on the titleblock. Any reference files or block files pertinent to the content of the master file is required dataand is to be included on the File Description.

10

3.3 FILE FORMAT

All submittals shall incorporate good drafting practices and organize information clearly andsystematically.

Graphic elements representing a physical component of the project (i.e., lines indicating a wall, ora block indicating a light fixture) shall be shown only one time in the submittals. If additionalreferences to the object are needed in additional drawing files they shall be shown via an externalreference of the original file.

Examples of acceptable organization of drawing information are shown in section S SubmittalPrototypes.

3.4 FILE SIZE AND ORGANIZATION

It is the responsibility of the consultant to organize drawing information coherently and maintainreasonable file sizes. Where possible file sizes should not exceed 1 to 2 megabytes. In no caseshall file sizes exceed 5 megabytes.

3.5 COPY AND COMPRESSION FORMAT

File requiring less than one diskette for transmission will be written to diskette using the DOScopy command. No other DOS commands will be acceptable (i.e. BACKUP RESTORE). If morethan one file is copied to a single diskette, the diskette label will include all file names, refer tosection 2.1.

Files larger than 1.44 megabytes are to be compressed using self-extracting files (i.e.PKZIP.EXE). Each file will be compressed independent of other files. No clustered filecompression’s will be acceptable. Compressed files shall be given the same file name as thedrawing file with an EXE extension

(i.e. A210A211.DWG =A210A211.EXE).

Where file sizes cannot be reasonably kept to a size that is compressible to one disk, submittalmay be compressed onto multiple disks using file compression software. Any compressed filesthat are not self-extracting shall be accompanied by the necessary decompression utilities.

3.6 Reference Files

Drawings using reference files are to list referenced files on the title block layer. This list will givean account of dependent files for the complete document. This information will also be added tothe file description for master files, refer to section 2.2. In all submittals reference files shall belocated in the same directory as the dependent files and shall NOT include path names in thereference file attachment.

3.7 Document File Format

One drawing file corresponding to each hard copy submittal sheet is to be saved in a plot-readyformat. Document files shall to be formatted utilizing paper space. Plotting shall be set to plot aview named “plot” with a plot scale of 1”=1”formatted to match the hard copy submittals.

11

3.8 FILE NAMING

All files included in the electronic data deliverable package will conform to the following filenaming convention. Alternative file naming conventions may be utilized only with prior writtenapproval of a detailed alternative. Approval of alternate naming conventions is solely at thediscretion of the University.

First, Second and Third Characters

XXX XXXXX.XXX

First, second and third character on all file name will identify the building number as listed in theCSU Space and Facilities Database. These numbers shall be obtained from the University. Oneand two digit building numbers shall be preceded by leading 0's to provide three (3) characterbuilding numbers.

Fourth Character

XXX X XXXX.XXX

Fourth character on all file names will identify additions or renovations to an existing building.This will be an alpha character. For file names representing new buildings, the number zero willbe used, i.e., A21 0 AP21.DWG.

Fifth Character

XXXX X XXX.XXX

Fifth character on all file names will identify the applicable consultant. They are as follows:

A ArchitectureC Civil EngineeringE Electrical EngineeringF Fire ProtectionG General Information (non-discipline specific)L Landscape ArchitectureM Mechanical EngineeringP Plumbing EngineeringQ CommunicationsS Structure EngineeringU Utilities Infrastructure (Campus wide)

12

3.8 FILE NAMING (Continued)

Sixth, Seventh and Eighth Characters Plus File Extension

XXXXX XXX.XXX

These six characters will be unique between the four different types of files included in thedeliverable package, refer to section 3.1.

FILE DESCRIPTION XXXXX XXX.XXX

File descriptions in ASCII format will only be required for drawing files. The last three charactersof the file name are to match the file being referenced to for both document files and master files.The extension is to be noted as “log”.

Example: A210AP21.DWG = A210A P21.LOG

SPECIFICATIONS XXXXX XXX.XXX

All specifications included in the deliverable package are to be compiled into one single text file.All specification file formats will be designated as SPC.TXT

Example: Specification #11680 = A210A SPC.TXT

All document files will use the last three digits of the drawing name. This number is to match thespecific drawing sheet referenced to.

Example: Sheet # A2.11 = A210A 211.DWG

MASTER FILES XXXXX XXX.XXX

All master files will use the last three digits of the drawing name. The first digit will identify thetype of sheet as follows:

XXXXX X XX.XXX

B = Building SectionsC = Reflected Ceiling PlanD = DetailE = Exterior ElevationsF = Floor PlanI = Interior ElevationsR = Roof PlanS = SchedulesS = Site PlanU = Utilities Infrastructure (Campus wide)W = Wall SectionsX = Demolition Plan

The second and third character will identify the floor number or drawing number.

XXXXXX XX .XXX

Example: 12th Floor Reflected Ceiling Plan = A210R C12.DWG

13

4.0 DRAWING FORMATS & GRAPHICS

Sheet border, title block, consultant’s stamp, logos and all other components of the master drawingsheet shall be located in paper space.

All graphic representations of the project or facility and all related notes, dimensions, symbols,etc., shall be constructed in model space.

All graphic entities shall be comprised of representational and geometrically accurate entities, e.g.a circle shall be represented by circle entity and NOT a visually equivalent collection of linesegments. Items shown in a dashed linetype shall be created with the LINETYPE feature and NOTby individual line elements.

4.1 STANDARD COORDINATE SYSTEM

The world coordinate system shall correspond to the California Coordinate System NAD 83 for allmap and plan view files. Where necessary for composting drawings on a sheet a user coordinatesystem named “PLAN VIEW” shall be established.

4.2 PROTOTYPE DRAWING FILES

Prototype drawing files and symbols shall be utilized when provided by the University. These mayinclude but not be limited to; typical title sheets, formatted drawing files, drawing symbology andother blocks. When blocks contain attributes all relevant attribute fields are to be filled out.

4.3 STANDARD SHEET SIZES AND FORMATS

All sheet sizes are to be limited to five standard formats. Required sheet size is specific to eachproject and is under the discretion of the University. They are as follows:

A Sized Plot 8 1/2/” x 11”B Sized Plot 11” x 17”C Sized Plot 24” x 36” (preferred format)D Sized Plot 30” x 42”

4.4 GRAPHICS

4.4.1 TEXT

All text is to be created only with the following standard AutoCAD's SHX files:

romans Suggested for most text and attribute entriesromand May be used for larger text sizes

romant Limit use to control regeneration timesitalict "italicc "

All text sizes are to plot and display in accordance with the following minimum sizes:

Schedules 1/8”Dimensions and Notes 1/8”Grid Numbers 3/16”Sheet Detail Title 3/16”Sheet Title 1/4”Sheet Number 3/8”

14

4.4.2 SPECIAL ENTITY REQUIREMENTS

All wall lines will have their thickness (vertical dimension) set to match the wall height.

All walls shall have a center line ("A-WALL" not plotted) with its’ thickness set to match the wallheight. Can serve as hook to Database Info.

Common symbols, doors, W.C.s, windows, equipment, etc., shall be blocks. Consultants shall usepredefined blocks when provided by the university.

Entities to be shown as blocks

•All Plumbing & Bath Fixtures e.g., water closets, urinals, lavatories, tubs, grab bars, accessories, mirrors

•All Electrical Devices & Hardware e.g., lighting fixtures, switches, outlets, panels

•Mechanical Equipment e.g., supply diffusers, return grilles, thermostats, air handlers,

•Doors (insert with scale set to door size)

•Windows (insert with scale to window size)

•Equipment, type II * II

•Furniture

•Drawing Symbols

•Door and window marks, room # indicators, scale indicators, north arrows

4.5 DIMENSIONING

All dimensions shown in the project submittals shall be fully associative. Dimension definitionpoints should be located with an appropriate Object Snap (End Point, M id Point, etc.) or otherwiselocated precisely on the project geometry. Manual imput of dimension text or otherwise overriding the actual dimensions is NOT acceptable in submittals to the university.

15

4.5 FILL AND HATCH PATTERNS

No rasterized images will be acceptable for either text or drawing files. Vectorized fill patterns areacceptable. Limit excessive use of hatch patterns to avoid unnecessarily large files. All consultantsare responsible for keeping files sizes within manageable limits. Refer to section 4.2 for copy andcompression formats.

4.6 Line Weights And Pen Assignments

Preliminary Recommendations:

These pen assignments are provided to support CSU personnel in producing consistent hardcopy output from the electronic submittals. Consultants are solely responsible for the productionand appearance of their hard copy submittals.

Note: While color #s 14, 54, 94, 134, 174, & 214 have no AutoCAD color name they are a greyedout red, yellow, green, cyan, blue, & magenta respectively on a standard 256 color AutoCADdisplay

Output Raster: Pen Plotter Pen Plotter

Device Inkjet/Laser 6 Pens 4 Pens

(Monochrome)

Typical Drawing AutoCAD

Layers * Color # Description Line Width % Fill Pen Size Color Pen Size Color

Patterns 1, Red Extra Fine 0.15 100% Pen 1 0.15 Black Pen 1 0.25 Black

Dimensions 2, Yellow Fine 0.25 100% Pen 2 0.25 Black Pen 1 0.25 Black

Notes, Text, 3, Green Light 0.35 100% Pen 3 0.35 Black Pen 2 0.35 Black

Titles, Project Info4, Cyan Medium 0.50 100% Pen 4 0.50 Black Pen 3 0.50 Black

Titles, Project Info 5, Blue Heavy 0.70 100% Pen 5 0.70 Black Pen 4 0.70 Black

Borders, Project Info6, MagentaExtra Heavy 0.90 100% Pen 6 0.90 Black Pen 4 0.90 BlackInfo

Halftones

Background Layers (Backgrounds)

14 Extra Fine 0.15 50% Pen 7 0.15 Green Pen 5 0.25 Green

54 Fine 0.25 50% Pen 8 0.25 Green Pen 5 0.25 Green

94 Light 0.35 50% Pen 9 0.35 Green Pen 6 0.35 Green

134 Medium 0.50 50% Pen 100.50 Green Pen 7 0.50 Green

174 Heavy 0.70 50% Pen 110.70 Green Pen 8 0.70 Green

214 Extra Heavy 0.90 50% Pen 120.90 Green Pen 8 0.70 Green

*All Submittals to the CSU shall have colors set by layer, colors shall not be set by entity.

16

5.0 LAYERING

All layering names and information within shall coincide with the following guidelines. Onlyapplicable layers are to be used. Blank layers are not to be included in the electronic datadeliverables. If reference files are used, refer to section 3.6 for additional direction.

Graphic representations of related items shall be located on a single layer even when indicated ondifferent drawings. E.g., Full height walls could be properly shown as A-WALL or A-WALL-FULL but not both.

Graphic indicators for text and notes, e.g., header line and arrowheads for a note, shall be locatedon the same layer as the corresponding text.

Layer names will be limited to 13 characters subdivided into 4 sections including: Major, Minor,Modifier and User Definer as shown below. Layer names of 5 and 9 characters mat be used whenappropriate and consistent with layer naming guidelines.

PROPOSED 13-CHARACTER LAYER NAME = X - XXXX - XXXX - XXXX

Major group _________ Minor group _____________Modifier (optional)________________User Definer (optional)_______________

Major group headings shall define the layer’s discipline as follows:

A = ArchitecturalC = CivilE = ElectricalF = Fire ProtectionL = LandscapeM = MechanicalP = PlumbingQ = CommunicationsS = Structural

Minor group headings shall define assemblies or construction systems such as walls, doors,ceilings or electrical power. Refer to section 5.1.

Modifier headings shall further define the minor group headings such as full height wall, partialheight wall, emergency lighting or general lighting. Refer to section 5.2.

User Defined heading shall further define the modifier group heading such as full height wallexisting and full height wall demolished. Refer to section 5.2.

Modifiers and user definer characters are options provided for extended clarification. Mostlayers on small projects will only require five (5) character major/minor format.

17

5.1 LAYER GUIDELINES BY DISCIPLINE

The CSU CAD Layer guidelines are of necessity both specific and open ended. The modularnature of guidelines allows for tremendous flexibility in delineating the myriad components ofCSU’s infrastructure.

The following discipline specific guidelines delineate the acceptable format of layer names forcommon project types. It should be noted that the naming structure is consistent across alldisciplines and common elements would be named identically in all disciplines. The organizationof layer names by discipline is merely a convenience to aid in finding the appropriate layer. Thelayer names comprise a single comprehensive system.

For example: A-DOOR is the only acceptable layer for indicating a door inall disciplines Electrical Plans, Plumbing Plans etc. By thesame logic E-LITE-EXIT is the only acceptable layer forindicating an exit light in an architectural drawing.

These disciplines specific guidelines shall be used whenever possible. Alternative layer names ororganization are not acceptable.

Where the nature of project or drawing requires it, consultants may propose expansions of thelayering guidelines. The proposed expansion shall be submitted in writing to the Office of theChancellor and are subject to revision or rejection at the discretion of the university. Acceptableexpansions shall utilize the Major Group Headings (see 5.0), Minor Group Abbreviations (see5.3), and modifiers and User Definitions (see 5.2) as provided, as well as the format shown below(see 5.1.x).

Accepted Expansions of the layer name guidelines may be included in future revisions of theCSU Competitor Aided Design Guidelines at the discretion of the university.

The color and linetype assignments for the layers are provided to support CSU personnel inproducing consistent hard copy output from the electronic submittals. Consultants are solelyresponsible for the production and appearance of their hard copy submittals.

18

5.1.1 ARCHITECTURAL LAYER GUIDELINES ____ Layer Description Color Linetype ____

Drawing Information Layers

A-PARE-**** Occupancy Plan & Area Designations InformationA-PCLG-**** Demolition Plan InformationA-PDEM-**** Ceiling Plan InformationA-PEQP-**** Equipment Plan InformationA-PFLR-**** Floor Plan InformationA-PLGS-**** Large Scale Floor Plan InformationA-PROF-**** Roof Plan Information

A-DETL-**** Detail Drawings InformationA-ELEV-**** Elevation DrawingsA-SECT-**** Section Drawings

A-****-DIMS Dimensions 2, Yellow ContinuousA-****-IDEN Repetitive Annotation, i.e. Rm No's/Equip No's 3, Green ContinuousA-****-KEYN ConDoc Key Notes 3, Green ContinuousA-****-NOTE Notes and Call-outs 3, Green ContinuousA-****-PATT Patterns, Cross Hatching, & Poche 1, Red ContinuousA-****-SYMB Symbols, Bubbles, and Targets 4, Cyan ContinuousA-****-SCHD Schedules and Tables of Text 3, Green ContinuousA-****-TEXT General Notes and Specifications 3, Green Continuous

Building Information Layers

A-WALL Walls 5, Blue ContinuousA-WALL-CNTR Wall Center Lines 2, Yellow CenterA-WALL-FULL Full Height Walls 6, Magenta ContinuousA-WALL-PRHT Partial Height Walls 4, Cyan ContinuousA-WALL-WHED Window Headers 3, Green ContinuousA-WALL-DHED Door Headers 3, Green ContinuousA-WALL-JAMB Door & Window Jambs 6, Magenta ContinuousA-WALL-PATT Wall Insulation, Hatch Patterns & Fill 1, Red Continuous

A-CLNG-OVHD Ceiling Elements, soffits, and Bulkheads 4, Cyan HiddenA-CLNG-GRID Ceiling Grid (T-Bar Ceiling) 1, Red Continuous

A-DOOR Doors 4, Cyan ContinuousA-DOOR-IDEN Door Number, Hardware Group, etc. 3, Green Continuous

A-GLAZ Window, Window Walls, Curtain Walls,Glazed Partitions 3, Green Continuous

A-GLAZ-SILL Window Sills 3, Green ContinuousA-GLAZ-IDEN Window Number 3, Green Continuous

19

5.1.1 Continued ____ Layer Description Color Linetype ____

A-FLOR Floor Information 3, Green ContinuousA-FLOR-LEVL Level Changes, Ramps, Pits, & Depression 5, Blue ContinuousA-FLOR-STRS Stairs, Escalators, and Ladders 4, Cyan ContinuousA-FLOR-HRAL Stair and Balcony Handrails and Guardrails 4, Cyan ContinuousA-FLOR-TPTN Toilet Portions 4, Cyan ContinuousA-FLOR-SPCL Architectural Specialties 4, Cyan Continuous

A-EQPM Equipment 4, Cyan ContinuousA-EQPM-FIXD Fixed Equipment (CSU Type 1) 4, Cyan ContinuousA-EQDM-MOVE Moveable Equipment (CSU Type 2) 3, Green DashedA-EQPM-IDEN Equipment Identification Numbers 3, Green Continuous

A-FURN Furniture 3, Green ContinuousA-FURN-IDEN Furniture Identification Numbers 3, Green Continuous

A-ROOF Roof Information 4, Cyan ContinuousA-ROOF-LEVL Level Changes 4, Cyan ContinuousA-ROOF-OTLN Roof Perimeter/Edge, Roof Geometry 6, Magenta ContinuousA-ROOF-STRS Stair Treads and Ladders 4, Cyan Continuous

20

5.1.2 STRUCTURAL LAYER GUIDELINES ____ Layer Description Color Linetype ____


S-PCOL-**** Column Plan InformationS-PFND-**** Foundation Plan InformationS-PSFR-**** Structural Framing Plan Information

S-DETL-**** Detail Drawings InformationS-ELEV-**** Elevation Drawings InformationS-SECT-**** Section Drawings Information

S-****-DIMS Dimensions 2,yellow ContinuousS-****-KEYN ConDoc Key Notes 3, Green ContinuousS-****-NOTE Notes, Call-outs, & Key Notes 3, Green ContinuousS-****-SYMB Symbols, Bubbles, & Targets 4, Cyan ContinuousS-****-SCHD Schedules and Tables of Text 3, Green ContinuousS-****-TEXT General Notes & Specifications 3, Green Continuous


S-ABLT Anchor Bolts & Hold-Downs 4, Cyan Continuous

S-COLS Structural Columns 6, Magenta ContinuousS-COLS-RBAR Reinforcing Bars 5, Blue ContinuousS-COLS-WELD-SYMB Welding Symbols 3, Green Continuous

S-FNDN-FTNG Footings 6, Magenta ContinuousS-FNDN-GRBM Grade Beams 6, Magenta ContinuousS-FNDN-PIER Piers 6, Magenta ContinuousS-FNDN-RBAR Reinforcing Bars 5, Blue ContinuousS-FNDN-WELD-SYMB Welding Symbols 3, Green Continuous

S-FRAM Framing 4, Cyan ContinuousS-FRAM-BEAM Beams 5, Blue Continuous

The drawing may be further segregated with sublayers if needed, e.g.:S-FRAM-BEAM-PRIM Primary Beams 6, Magenta ContinuousS-FRAM-BEAM-SCND Secondary Beams 4, Cyan Continuous

S-FRAM-DECK Structural Decking 4, Cyan ContinuousS-FRAM-JOIS Joists 6, Magenta ContinuousS-FRAM-RBAR Reinforcing Bars 5, Blue ContinuousS-FRAM-WELD-SYMB Welding Symbols 3, Green Continuous

21

5.1.2 Continued ____ Layer Description Color Linetype ____

S-GRID Column Grid 2, Yellow CenterS-GRID-IDEN Column Grid Tags 4, Cyan Continuous

S-JNTS-CNST Construction Joints 4, Cyan ContinuousS-JNTS-CTRL Control Joints 4, Cyan Continuous

S-SLAB Concrete Slabs 4, Cyan ContinuousS-SLAB-OTLN Slab Outline 6, Magenta ContinuousS-SLAB-RBAR Concrete Slab Reinforcing 5, Blue Continuous

S-WALL Structural Bearing & Sheer Walls 4, Cyan Continuous

22

5.1.3 MECHANICAL LAYER GUIDELINES ____ Layer Description Color Linetype ____


M-PCON-**** Mechanical Controls Plan InformationM-PHVA-**** HVAC Plan InformationM-PLGS-**** Large Scale HVAC Plan InformationM-PPIP-**** Piping Plan InformationM-PROF-**** Mechanical Roof Plan InformationM-PSTM-**** Steam Piping Plan InformationM-PWCH-**** Chilled Water Piping Plan InformationM-PWHT-**** Hot Water Piping Plan Information

M-DETL-**** Detail Drawings InformationM-ELEV-**** Elevation Drawings InformationM-SECT-**** Section Drawings Information

M-****-DIMS Dimensions 2,yellow ContinuousM-****-KEYN ConDoc Key Notes 3, Green ContinuousM-****-NOTE Notes, Call-outs, & Key Notes 3, Green ContinuousM-****-SYMB Symbols, Bubbles, & Targets 4, Cyan ContinuousM-****-SCHD Schedules and Tables of Text 3, Green ContinuousM-****-TEXT General Notes & Specifications 3, Green Continuous


M-DUCT-SUPP HVAC System Supply Ductwork 4,Cyan ContinuousM-DUCT-RETN HVAC System Return Ductwork 4,Cyan ContinuousM-DUCT-EXHT HVAC System Exhaust Ductwork 4,Cyan ContinuousM-DUCT-OTHR HVAC System Other Ductwork 4,Cyan Continuous

M-HVAC-EQPM HVAC Equipment 5, Blue Continuous

M-CDFF-SUPP Ceiling Supply Diffusers 5, Blue ContinuousM-CDFF-RETN Ceiling Return Diffusers 5, Blue ContinuousM-ODFF Other Diffusers 5, Blue Continuous

M-CONT Controls & Instrumentation 4, Cyan ContinuousM-CONT-THER Thermostats 4, Cyan ContinuousM-CONT-WIRE Low Voltage Wiring 4, Cyan Continuous

M-ENER-SYST Energy Management Systems 4,Cyan Continuous

M-EXHS-DUCT Exhaust System Ductwork 4,Cyan ContinuousM-EXHS-EQPM Exhaust System Equipment 5, Blue Continuous

23

5.1.3 CONTINUED ____ Layer Description Color Linetype ____

Chilled Water SystemM-CWTR-EQPM Chilled Water Equipment 5, Blue ContinuousM-CWRT-FIXT C.W. Above Ground Elements, e.g. Manholes 5, Blue ContinuousM-CWRT-NOTE Chilled Water Notes 3, Green ContinuousM-CWTR-PIPE Chilled Water Pipe 4,Cyan Continuous

When Layers below are used to segregate supply& return subgroup PIPE may NOT be used.

M-CWTR-RTRN Chilled Water Return Lines 4, Cyan Continuous

M-CWTR-SUPL Chilled Water Supply Lines 4, Cyan Continuous

M-DUAL-PIPE Dual Temperature System Pipe 4,Cyan Continuous

M-DUAL-EQPM Dual Temperature System Equipment 5, Blue Continuous

Hot Water (Space Heating) SystemM-HOTW-EQPM Hot Water Equipment 5, Blue ContinuousM-HOTW-FIXT H.W. Above Ground Elements, e.g. Manholes 5, Blue ContinuousM-HOTW-PIPE Hot Water Pipe 4,Cyan Continuous

When Layers below are used to segregate supply& return subgroup PIPE may NOT be used.

M-HOTW-RTRN Hot Water Return Lines 4, Cyan ContinuousM-HOTW-SUPL Hot Water Supply Lines 4, Cyan Continuous

M-REFG-EQPM Refrigeration System Equipment 5, Blue ContinuousM-REFG-PIPE Refrigeration System Piping 4,Cyan Continuous

M-STEM-LPIP Low Pressure Steam Piping 4,Cyan ContinuousM-STEM-MPIP Medium Pressure Steam Piping 4,Cyan ContinuousM-STEM-HPIP High Pressure Steam Piping 4,Cyan ContinuousM-STEM-EQPM Refrigeration System Equipment 5, Blue Continuous

M-SPCL-**** Special Systems

M-VENT-DUCT Industrial or Laboratory Venting 4,Cyan ContinuousM-VENT-EQPM Industrial or Laboratory Venting Equipment 4,Cyan Continuous

24

5.1.4 PLUMBING LAYER GUIDELINES ____ Layer Description Color Linetype ____


P-PPLM -**** Plumbing Plan Information

P-DETL-**** Detail Drawings InformationP-ELEV-**** Elevation Drawings InformationP-SECT-**** Section Drawings InformationP-RISR -**** Plumbing Riser Diagram Information

P-****-NOTE Notes, Call outs, and Key Notes 3, Green ContinuousP-****-TEXT General Notes and Specifications 3, Green ContinuousP-****-SYMB Symbols, Bubbles, and Targets 4, Cyan ContinuousP-****-DIMS Dimensions 2, Yellow ContinuousP-****-SCHD Schedules and Tables of Text 3, Green Continuous


Acid, Alkaline, and Oil Waste SystemP-ACID-PIPE Acid, Alkaline, and Oil Waste System Piping 4, Cyan ContinuousP-ACID-EQPM Acid, Alkaline, and Oil Waste System Equipment 5, Blue Continuous

Domestic Hot & Cold Water SystemP-DOMW-PIPE Domestic Hot and Cold Water Piping 4, Cyan ContinuousP-DOMW-EQPM Domestic Hot and Cold Water Equipment 5, Blue Continuous

Sanitary DrainageP-SANR-PIPE Sanitary Piping 4, Cyan ContinuousP-SANR-VENT Sanitary Vent Piping 4, Cyan ContinuousP-SANR-EQPM Sanitary Equipment 5, Blue ContinuousP-SANR-FTXT Sanitary Fixture 5, Blue Continuous

Storm Drainage SystemP-STRM-PIPE Storm Drain Piping 4, Cyan ContinuousP-STRM-RFDR Roof Drains 5, Blue Continuous

Natural Gas SystemP-NGAS-PIPE Natural Gas System Piping 4, Cyan ContinuousP-NGAS-EQPM Natural Gas System Equipment 5, Blue Continuous

Laboratory Gas SystemP-LABS-PIPE Laboratory Gas Piping 4, Cyan ContinuousP-LABS-EQPM Laboratory Equipment 5, Blue Continuous

25

5.1.5 FIRE PROTECTION SYSTEMS LAYER GUIDELINES ____ Layer Description Color Linetype ____


F-PSPR-**** Sprinkler PlanF-PFPE-**** Fire Protection Equipment Plan

F-RISR-**** Sprinkler Riser Program

F-DETL-**** Detail Drawings InformationF-SECT-**** Section Drawings Information

F-****-NOTE Notes, Call outs, and Key Notes 3, Green ContinuousF-****-TEXT General Notes and Specifications 3, Green ContinuousF-****-SYMB Symbols, Bubbles, and Targets 4, Cyan ContinuousF-****-DIMS Dimensions 2, Yellow ContinuousF-****-SCHD Schedules and Tables of Text 3, Green Continuous


F-CO2S-PIPE CO2 (Carbon Dioxide) System Piping 4, Cyan ContinuousF-CO2S-EQPM CO2 (Carbon Dioxide) System Equipment 5, Blue Continuous

F-HALN-PIPE Halon System Piping 4, Cyan ContinuousF-HALN-EQPM Halon Equipment 5, Blue ContinuousF-HALN-SPHD Halon Spray Heads 5, Blue Continuous

F-SPRN-SPHD Fire Protection Sprinkler Heads 5, Blue ContinuousF-SPRN-PIPE Fire Protection Sprinkler Piping 4, Cyan Continuous

F-STAN-EQIP Fire Protection Standpipe Equipment 5, Blue ContinuousF-STAN-PIPE Fire Protection Standpipe Piping 4, Cyan Continuous

F-PROT-EQPM Fire System Equipment(Fire Hose Cabinet, Extinguishers) 5, Blue Continuous

F-PROT-ALRM Fire Alarm 5, Blue ContinuousF-PROT-SMOK Smoke Detectors or Heat Sensors 5, Blue Continuous

26

5.1.6 ELECTRICAL LAYER GUIDELINES ____ Layer Description Color Linetype ____


E-PAUX-**** Auxiliary Systems Plan InformationE-PCOM-**** Communications Plan InformationE-PLIT-**** Lighting Plan InformationE-PPOW-**** Power Plan Information

E-RISR-**** Electrical Riser Diagrams

E-DETL-**** Detail Drawings InformationE-SECT-**** Section Drawings Information

E-****-NOTE Notes, Call outs, and Key Notes 3, Green ContinuousE-****-TEXT General Notes and Specifications 3, Green ContinuousE-****-SYMB Symbols, Bubbles, and Targets 4, Cyan ContinuousE-****-DIMS Dimensions 2, Yellow ContinuousE-****-SCHD Schedules and Tables of Text 3, Green Continuous


LightingE-LITE-CLNG Ceiling Mounted Lighting 5, Blue ContinuousE-LITE-EXIT Exit Lighting 5, Blue ContinuousE-LITE-EMER Emergency Lighting 5, Blue ContinuousE-LITE-FLOR Floor Lighting 5, Blue ContinuousE-LITE-ROOF Roof Mounted Lighting 5, Blue ContinuousE-LITE-SITE Site Lighting Fixtures 5, Blue ContinuousE-LITE-SWCH Lighting Switches 5, Blue ContinuousE-LITE-WIRE Wiring and Conduit 5, Blue DashedE-LITE-NUMB Lighting Circuit Numbers 4, Cyan ContinuousE-LITE-IDEN Luminaire Identification and Text 4, Cyan Continuous

PowerE-POWR-WALL Wall Outlets & Receptacles 5, Blue ContinuousE-POWR-CLNG Ceiling Receptacles and Devices 5, Blue ContinuousE-POWR-FLOR Floor Mounted Outlets 5, Blue ContinuousE-POWR-EQPM Power Equipment 5, Blue ContinuousE-POWR-CABL Cable Trays 4, Cyan ContinuousE-POWR-NUMB Power Circuit Numbers 4, Cyan ContinuousE-POWR-WIRE Power Wiring and Conduit 4, Cyan Dashed

Electrical Control SystemsE-CTRL-EQPM Control System Equipment & Devices 5, Blue ContinuousE-CTRL-WIRE Control System Wiring 4, Cyan Dashed

E-GRND Electrical Ground System 3, Green Continuous

E-PROT-WIRE Fire Protection System Wiring 3, Green Dashed

E-WKLP-INFO Clearances and work space req. (NEC Codes etc.) 2, Yellow Dashed

27

5.1.7 CIVIL LAYER GUIDELINES ____ Layer Description Color Linetype ____


C-PGRD-**** Grading Plan InformationC-PPAV-**** Paving Plan Information

C-DETL-**** Detail Drawings InformationC-SECT-**** Section Drawings Information

C-****-NOTE Notes, Call outs, and Key Notes 3, Green ContinuousC-****-TEXT General Notes and Specifications 3, Green ContinuousC-****-SYMB Symbols, Bubbles, and Targets 4, Cyan ContinuousC-****-DIMS Dimensions 2, Yellow ContinuousC-****-SCHD Schedules and Tables of Text 4, Cyan Continuous

Project Information Layers

Property Lines & Survey BenchmarksSee Section 5.1.8 for Topographic Contour Layers

Contour Lines & ElevationsSee Section 5.1.9 for Topographic Contour Layers

C-BLDG-EXST Footprint of Existing Building 3, Green ContinuousC-BLDG-DEMO Footprint of Existing Bldg. to be Demolished 3, Green Continuous

C-PKNG Parking Lots 3, Green ContinuousC-PKNG-STRP Parking Lot Striping, and Pavement 3, Green ContinuousC-PKNG-CARS Graphic Illustration of Cars 1, Red ContinuousC-PKNG-CURB Curbs and Wheel Stops 3, Green Continuous

C-ROAD Roads 3, Green ContinuousC-ROAD-CNTR Road Center Lines 3, Green ContinuousC-ROAD-CURB Curbs 3, Green ContinuousC-ROAD-BRDG Roadway Bridges 4, Cyan ContinuousC-ROAD-PROP Proposed Road 4, Cyan ContinuousC-ROAD-DEMO Existing Road to be Demolished 3, Green Continuous

C-STRM-CULV Culverts, Headwalls, Drainage Inlets 6, Magenta ContinuousC-STRM-IDEN Storm Sewer System Annotation 4, Cyan ContinuousC-STRM-DTCH Drainage Ditches 3, Green Dashed

P-STRM-FIXT Storm Drainage Surface Features 5, Blue Continuous(Catch Basins, Manholes)

P-STRM-PIPE Storm Drain Pipes 5, Blue Dashed

Site utilities use the same layering protocols as building utilities, e.g. Site Lighting would be:E-LITE-SITE Site Lighting Fixtures 5, Blue ContinuousE-LITE-WIRE Wiring and Conduit 5, Blue DashedE-LITE-NUMB Lighting Circuit Numbers 4, Cyan Continuous

See the appropriate discipline specific guidelines e.g. 5.1.6 for site utilities layering.

28

5.1.8 BOUNDARY SURVEY LAYER GUIDELINES

____ Layer Description Color Linetype ____


C-PBND-**** Boundary Plan Information

C-****-NOTE Notes, Call outs, and Key Notes 3, Green ContinuousC-****-TEXT General Notes and Specifications 3, Green ContinuousC-****-SYMB Symbols, Bubbles, and Targets 4, Cyan ContinuousC-****-DIMS Dimensions 2, Yellow Continuous


C-GRID Grid Lines (California Coordinates) 1, Red ContinuousC-GRID-NOTE Grid Coordinates and Notes 3, Green Continuous

C-PROP Property Line (Campus Boundary) 4, Cyan PhantomC-PROP-NOTE Property Line Notes 5, Blue ContinuousC-PROP-ESMT Easements 6, Magenta ContinuousC-PROP-DIMS Boundary and Distance Notations 2, Yellow Continuous

C-PROP-ESMT Easements, Right of Ways, Setback Lines 6, Magenta ContinuousC-PROP-BRNG Bearings and Distance Labels 4, Cyan Continuous

C-ROAD Roads and Streets 5, Blue ContinuousC-ROAD-IDEN Road and Street Names 4, Cyan Continuous

29

5.1.9 TOPOGRAPHIC PLANS LAYER GUIDELINES ____ Layer Description Color Linetype ____


C-PTOP-**** Topographic Plan Information

C-DETL-**** Detail Drawings InformationC-SECT-**** Section Drawings Information

C-****-NOTE Notes, Call outs, and Key Notes 3, Green ContinuousC-****-TEXT General Notes and Specifications 3, Green ContinuousC-****-SYMB Symbols, Bubbles, and Targets 6, Magenta ContinuousC-****-DIMS Dimensions 6, Magenta ContinuousC-****-SCHD Schedules and Tables of Text 6, Magenta Continuous


C-GRID Grid Lines (California Coordinates) 3, Green ContinuousC-GRID-NOTE Grid Coordinates and Notes 3, Green Continuous

C-BLDG Building Outline 2, Yellow ContinuousC-BLDG-ELEV Building Elevations 2, Yellow Continuous

Topographic InformationC-TOPO-SPOT Spot Elevations (Tick Marks & Text) 3, Green ContinuousC-TOPO-MAJR Major Contour Lines 6, Magenta Dash DotC-TOPO-MAJR-TEXT Major Contour Lines Text (Elevation) 3, Green ContinuousC-TOPO-MINR Minor Contour Lines 4, Cyan Dash DotC-TOPO-MINR-TEXT Minor Contour Lines Text (Elevation) 3, Green ContinuousC-TOPO-DEMO Existing Contour Lines to be Changed 2, Yellow 2 DashedC-TOPO-MACL Major Depressed Contour Lines (Wet lands) 4, Cyan ContinuousC-TOPO-MICL Minor Depressed Contour Lines (Wet lands) 6, Magenta Continuous

C-PROP Property Line (Campus Boundary) 4, Cyan PhantomC-PROP-NOTE Property Line Notes 5, Blue ContinuousC-PROP-ESMT Easements 6, Magenta Continuous

C-ROAD Roads and Streets 6, Magenta ContinuousC-ROAD-CURB Curb Lines 3, Green ContinuousC-ROAD-NOTE Road and Street Names 3, Green ContinuousC-ROAD-BRDG Roadway Bridges 4, Cyan ContinuousL-WALK Pedestrian Walks 3, Green ContinuousL-WALK-BRDG Pedestrian Bridges 4, Cyan ContinuousC-PKNG Parking Lot 3, Green ContinuousC-PKNG-NOTE Parking Lot Notes 3, Green ContinuousC-PKNG-TEXT Parking Lot Text 3, Green Continuous

L-SITE-WATR Site Water Features, Rivers, Streams, 1, Red Continuous Ponds, and Coastlines

L-SITE-WATR-NOTE Names and Notes 3, Green Continuous

30

5.1.10 LANDSCAPE LAYER GUIDELINES ____ Layer Description Color Linetype ____


L-PIRR-**** Landscape Irrigation Plan InformationL-PPLA-**** Landscape Planting Plan Information

L-DETL-**** Detail Drawings InformationL-SECT-**** Section Drawings InformationL-PSTR-**** Structural Plan Information

L-****-NOTE Notes, Call outs, and Key Notes 3, Green ContinuousL-****-TEXT General Notes and Specifications 3, Green ContinuousL-****-SYMB Symbols, Bubbles, and Targets 4, Cyan ContinuousL-****-DIMS Dimensions 2, Yellow ContinuousL-****-SCHD Schedules and Tables of Text 3, Green Continuous


Landscape PlantingL-PLNT-TREE Tree 3, Green ContinuousL-PLNT-EXST Existing Plants to Remain 3, Green ContinuousL-PLNT-DEMO Existing Plants to be Demolished 3, Green ContinuousL-PLNT-GRND Ground Cover and Vines 3, Green ContinuousL-PLNT-SHRB Shrubs & Bushes 5, Blue ContinuousL-PLNT-TURF Lawn Areas 3, Green ContinuousL-PLNT-BEDS Landscape Planting Beds 3, Green Continuous

Landscape Irr igat ioSystemL-IRRG-MAJR Main Irrigation Lines (larger than 2”) 3, Green ContinuousL-IRRG-SPHD Sprinkler Head 6, Magenta ContinuousL-IRRG-PIPE Sprinkler Piping 3, Green ContinuousL-IRRG-EQPM Irrigation Equipment 6, Magenta ContinuousL-IRRG-COVR Irrigation Coverage 3, Green ContinuousL-WALK Walks, Steps, and 3, Green ContinuousL-WALK-PATT Patterns and Cross Hatching 3, Green Continuous

Site ImprovementsL-SITE-FENC Fencing 5, Blue ContinuousL-SITE-WALL Walls 6, Magenta ContinuousL-SITE-DECK Decks 4, Cyan ContinuousL-SITE-BRDG Pedestrian Bridges 4, Cyan ContinuousL-SITE-POOL Pools and Spas 6, Magenta Continuous

31

5.1.11 CAMPUS MASTER PLAN LAYER GUIDELINES ____ Layer Description Color Linetype ____


C-PMST-SYMB Symbols, Arrows, Graphic Scales, etc. 4, Cyan ContinuousC-PMST-LEGN Legend of Building Names & Numbers 3, Green ContinuousC-PMST-NOTE Notes 3, Green ContinuousC-PMST-**** Other Campus Master Plan Information

C-SHDB-LGND Building Legend (in Paper Space) 4, Cyan ContinuousC-SHDB-NOTE Master Plan Notes (in Paper Space) 3, Green Continuous

Campus Information Layers

C-BLDG-EXST Existing Building Outline 6, Magenta ContinuousC-BLDG-EXST-NOTE Existing Building Number 4, Cyan ContinuousC-BLDG-EXST-PATT Existing Building Hatch Pattern 3, Green ContinuousC-BLDG-TEMP Existing Temporary Building Outline 3, Green ContinuousC-BLDG-TEMP-NOTE Existing Temporary Building Number 3, Green Continuous

C-BLDG-PROP Proposed Building Outline 5, Blue ContinuousC-BLDG-PROP-NOTE Proposed Building Number 4, Cyan ContinuousC-BLDG-PROP-PATT Proposed Building Pattern 1, Red Continuous

C-ROAD Roads and Streets 6, Magenta ContinuousC-ROAD-CURB Curb Lines 3, Green ContinuousC-ROAD-NOTE Road and Street Names 4, Cyan ContinuousC-ROAD-BRDG Roadway Bridges 6, Magenta ContinuousC-ROAD-GUTR Roadway Gutters 2, Yellow Continuous

L-WALK Pedestrian Walks 4, Cyan ContinuousL-WALK-BRDG Pedestrian Bridges 5, Blue Continuous

C-PKNG-EXST Parking Lot 3, Green ContinuousC-PKNG-EXST-NOTE Parking Lot 3, Green ContinuousC-PKNG-EXST-TEXT Parking Lot Notes (Number of Spaces) 3, Green ContinuousC-PKNG-PROP Proposed Parking Lot 3, Green ContinuousC-PKNG-PROP-NOTE Proposed Parking Lot Number 3, Green Continuous

C-BLDG-EXST Existing Building Outline 3, Green ContinuousC-BLDG-EXST-NOTE Existing Building Number 3, Green ContinuousC-BLDG-EXST-PATT Existing Building Hatch Pattern 1, Red ContinuousC-BLDG-TEMP Existing Temporary Building Outline 3, Green ContinuousC-BLDG-TEMP-NOTE Existing Temporary Building Number 3, Green ContinuousC-BLDG-TEMP-PATT Existing Temporary Building Hatch Pattern 1, Red Continuous

C-BLDG-PROP Proposed Building Outline 3, Green ContinuousC-BLDG-PROP-NOTE Proposed Building Number 3, Green ContinuousC-BLDG-PROP-PATT Proposed Building Pattern 1, Red Continuous

L-SITE-WATR Site Water Features, Rivers, Streams, 5, Blue ContinuousPonds, and Coastlines

L-SITE-WATR-NOTE Names and Notes 4, Cyan Continuous

32

5.1.12 UTILITY INFRASTRUCTURE LAYER GUIDELINES ____ Layer Description Color Linetype ____


C-PUTL-**** Site Utility Plan Information

C-DETL-**** Detail Drawings InformationC-ELEV-**** Elevation Drawings InformationC-SECT-**** Section Drawings Information

C-****-NOTE Notes, Call-outs, and Key Notes 3, Green ContinuousC-****-TEXT General Notes and Specifications 3, Green ContinuousC-****-SYMB Symbols, Bubbles, and Targets 6, Magenta ContinuousC-****-DIMS Dimensions 6, Magenta ContinuousC-****-SCHD Schedules and Tables of Text 6, Magenta Continuous

Topographic Plan Information

All topographic plan data is to be contained in a separate drawing file and incorporated into utility plans via referencesfiles.

Utility Information Layers

P-SSWR Sanitary Sewer System 3, green ContinuousP-SSWR-MHOL Sanitary Sewer Manholes 4, Cyan ContinuousP-SSWR-ELEV Sanitary Sewer Elevations 4, Cyan ContinuousP-SSWR-PIPE Sanitary Sewer Pipe 3, Green ContinuousP-SSWR-NOTE Sanitary Sewer Notes 3, Green ContinuousP-SSWR-EQPM Sanitary Sewer Equipment 6, Magenta Continuous

P-STRM Storm Drain SystemP-STRM-MHOL Sanitary Sewer Manholes 4, Cyan ContinuousP-STRM-ELEV Sanitary Sewer Elevations 4, Cyan ContinuousP-STRM-PIPE Sanitary Sewer Pipe 3, Green ContinuousP-STRM-NOTE Sanitary Sewer Notes 3, Green ContinuousP-STRM-EQPM Sanitary Sewer Equipment 6, Magenta Continuous

P-GSWR Grey Water System 3, Green ContinuousP-GSWR-MHOL Grey Water Manholes 4, Cyan ContinuousP-GSWR-ELEV Grey Water Elevations 4, Cyan ContinuousP-GSWR-PIPE Grey Water Pipe 3, Green ContinuousP-GSWR-NOTE Grey Water Notes 3, Green ContinuousP-GSWR-EQPM Grey Water Equipment 6, Magenta Continuous

P-DOMW Domestic Water System 3, Green ContinuousP-DOMW-MHOL Domestic Water Manholes 4, Cyan ContinuousP-DOMW-ELEV Domestic Water Elevations 4, Cyan ContinuousP-DOMW-PIPE Domestic Water Pipe 3, Green ContinuousP-DOMW-NOTE Domestic Water Notes 3, Green Continuous

33

5.1.12 CONTINUED

____ Layer Description Color Linetype ____

Hot Water (Space HeatingSystemM-HOTW-FIXT Chilled Water Surface Features e.g. Manholes 4, Cyan ContinuousM-HOTW-EQPM Hot Water Equipment 5, Blue ContinuousM-HOTW-NOTE Hot Water Notes 3, Green ContinuousM-HOTW-PIPE Hot Water Piping 4, Cyan Continuous

Use when supply & return are shown together,may NOT be used when layers below are used

M-HOTW-RTRN Hot Water Return Lines 4, Cyan ContinuousM-HOTW-SUPL Hot Water Supply Lines 4, Cyan Continuous

Chilled Water (SpacCooling)SystemM-CWRT-FIXT Chilled Water Surface Features e.g. Manholes 4, Cyan ContinuousM-CWRT-EQPM Chilled Water Equipment 5, Blue ContinuousM-CWRT-NOTE Chilled Water Notes 3, Green ContinuousM-CWRT-PIPE Chilled Water Piping 4, Cyan Continuous

Use when supply & return are shown together,may NOT be used when layers below are used

M-CWRT-RTRN Chilled Water Return Lines 4, Cyan ContinuousM-CWRT-SUPL Chilled Water Supply Lines 4, Cyan Continuous

Natural Gas SystemM-NGAS-EQPM Natural Gas Equipment 5, Blue ContinuousM-NGAS-PIPE Natural Gas Pipe 3, Green ContinuousM-NGAS-NOTE Natural Gas Notes 3, Green ContinuousM-NGAS-MHOL Natural Gas Manholes 3, Green Continuous

Communication SystemQ-COMM-EQPM Communication Equipment 3, Green ContinuousQ-COMM-WIRE Wiring Cables, Duct Banks & Conduits 3, Green ContinuousQ-COMM-NOTE Communication System Notes 3, Green Continuous

34

5.2 MINOR GROUP ABBREVIATIONS

All minor group headings shall comply with the following abbreviation outline:

____ Layer Description ____

ABLT Anchor BoltsACID Acid, Alkaline, And Oil Waste SystemsALRM Alarm SystemAREA Area Calculations & Occupancy InfoAUXL Auxiliary Systems

BELL Bell SystemBLDG Building Foot PrintBRIN Brine System

CCTV Closed Circuit TelevisionCHIM Prefabricated ChimneysCLNG Ceiling InformationCLOK Clock SystemCOMM Telephone & Communication SystemCMPA Compressed Air SystemCOLS ColumnsCO2S Co2 SystemCTRL Control & Instrumentation SystemCWTR Chilled Water System

DATA Data SystemDETL DetailsDICT Central Dictation SystemDOMW Domestic Hot & Cold Water SystemDOOR DoorsDUST Dust & Fume Collection SystemDIMS Dimensions

ELEV Interior & Exterior ElevationsENER Energy Management SystemEQPM EquipmentEXHS Exhaust System

FIRE Fire Protection Or Alarm SystemFIXT FixturesFLOR Floor InformationFNDN FoundationFRAM Framing Plan (Beams & Joists)FUEL Fuel System PipingFURN Furniture

GLAZ Windows & Curtain WallsGRID Column GridGRND Ground (Elec.)And/Or (Planting)GSWR Grey Water System

HALN Halon SystemHOTW Hot Water Heating SystemHVAC Hvac System

35

5.2 MINOR GROUP ABBREVIATIONS (Continued) ____ Layer Description ____

INTC Intercom SystemIRRG Irrigation System

LEGN Legend Of SymbolsLLIN Single Line DiagramLITE

LTNG Lighting Protection System

MACH Machine Shop EquipmentMDGS Medical SystemMETL Miscellaneous Metal

NGAS Natural Gas & Storage TanksNURS Nurse Call SystemNOTE Notes, Call Outs, & Keynotes

PGNG Paging SystemPKGN ParkingPLNT PlantingPOWR PowerPROC Processing SystemPROP Property LinePROT Fire Protection System

Plan Information Minor GroupsPARE Area Calculation Plan InformationPBND Boundary Plan InformationPCLG Ceiling Plan InformationPCOL Column Plan InformationPCOM Communications Plan InformationPCON Controls Plan InformationPDEM Demolition Plan InformationPEQM Equipment Plan InformationPFLR Floor Plan InformationPFND Foundation Plan InformationPHVA HVAC Plan InformationPIRR Irrigation Plan InformationPLGS Large Scale Plan InformationPLIT Lighting Plan InformationPMCH Mechanical Plan InformationPPIP Piping Plan InformationPPLA Planting Plan InformationPPLM Plumbing Plan InformationPROF Roof Plan InformationPSFR Structural Framing Plan InformationPSPR Sprinkler Plan InformationPSTR Structural Plan InformationPSYS System Plan InformationPUTL Site Utility Plan Information

36

5.2 MINOR GROUP ABBREVIATIONS (Continued)


REFG Refrigeration SystemRISR Riser Diagram Or PlanROAD RoadsROOF Roof

SANR Sanitary DrainageSCHD Scheduled & Title Block SheetsSECT SectionsSERT Security SystemSHBD Sheet Boarder & Title Block Line WorkSITE Site Improvements

SLAB SlabSTEM Steam SystemsSTRM Storm Drain SystemSPCL Special SystemSPRN Fire Protection Sprinkler SystemSSWR Sanitary Sewer

(Manhole, Pumping Station)

STAN Fire Protection Standpipe SystemSOUN Sound Or Pa SystemSYMB Symbols, Bubbles, And Targets

TEST Test EquipmentTOPO Proposed Contour Lines & ElevationsTVAN Television Antenna SystemTREE TreeTEXT General Notes & Specifications

WALK Walks And StepsWALL WallsWATR Domestic Water

37

5.3 MODIFIERS AND USER DEFINITIONS


ACCS AccessALRM AlarmAPPL Appliances

BEAM BeamsBEDS Landscaping BedsBORE Test BoringsBRDG BridgesBRNG Bearings & Distance LabelsBUSW Busways

CABL Cable TraysCARS Graphic Illustration Of CarsCASE CaseworkCDFF Hvac Ceiling DiffusersCEQP Compressed Air EquipmentCHAR Chairs & Other SeatingCIRC CircuitsCNTR CenterlinesCONP Steam Systems Condensate PipingCONS Construction ControlsCOVR CoverageCPIP Compressed Air PipingCURB CurbsCLNG CeilingCTRL Controls

DECK Decking Or DecksDEMO Existing To Be RemovedDEVC DevicesDIAG DiagramDIMS DimensionsDRAN Drainage System Or IndicationDUCT Duct WorkDHED Door Header

EDGE Edge Of PerimeterELEV Elevation Or Elevated Surface

(3d Element)EMER EmergencyEQPM EquipmentEQUI Equipotential SystemESMT Easements, Right-Of-Way & Set BacksEVTR Elevator EquipmentEXIT ExitingEXST Existing To Remain

38

5.3 MODIFIERS AND USER DEFINITIONS (Continued)


FEED FeedersFENC FencingFILE File CabinetsFIXD FixedFIXT FixturesFLDR Floor Drains

FNSH FinishesFREE Free Standing Or Self SupportingFULL Full HeightFURN Furniture

FLOR Floor Located

GGEP Fuel Gas General PipingGPRP Fuel Gas Process PipingGRID GridGRND Ground Cover And VinesGUTR Gutters

HPIP High Pressure PipingHRAL Stair & Balcony Hand/GuardrailsHAZW Hazardous Waste Materials

IDEN Identification TagINTR Elements On The Interior Of Bldg.ISLD Islands

JAMB Door And Window JambsJOIN JointJOIS Joists

LEVL Elevation ChangesLOGO Office Or Project LogoLPIP Low Pressure Piping

MAJR Major (I.E. Contours)MINR Minor (I.E. Contours)MACL Major Depressed Contour LinesMBND Material Beyond Section CutMCUT Material Cut By SectionMICL Minor Depressed Contour LinesMOVE Movable ElementsMHOL Manholes

NEWW New Of Proposed WorkNICN Not In ContractNOTE Notes, Call-Outs & Keynotes*NPLT Nonplot Information & Const. LinesNUMB Numbering. For Systems; Circuits & Branches

39

5.3 MODIFIERS AND USER DEFINITIONS (Continued) ____ Layer Description ____

OCCP Occupant Or Employee NameODFF Hvac DiffusersOGEP Fuel Oil General PipingOPEN OpenOPRP Fuel Oil Process PipingOTLN OutlineOVHD Overhead

PATT Cross-Hatching And PochePACL Proposed Major Contour LinesPANL Panel Or Equipment BoardsPEQP Process Air EquipmentPICL Proposed Minor Contour LinesPILE Piles Or Drilled PiersPILE PipingPLAY PlaygroundPLNT PlantingPLOT Plotting Targets & WindowsPNLS Panel SystemPOLE PolePOOL Pools And SpasPOWR System Power DesignationPPIP Process Air PipingPRHT Partial HeightPROP Proposed

ROOF Roof LocatedRAIS Raised Floors Or PlatformRBAR Reinforcing BarsRDME Non Plotting Read Me InformationREFR Reference SystemRISR Riser Diagram Or PlanRFDR Roof DrainsRFEQ Roof Top Exhaust EquipmentRTWL Retaining WallRTRN Return Lines

SCHD Schedules And Title Block SheetsSIGN SignageSILL Window SillsSITE Site LocatedSMOK Smoke Detectors Or Heat SensorSPCL Specialties And Accessories

SPHD Sprinkler HeadSPOT Spot ElevationsSPRT Sport Area Or EquipmentSTOR Storage Equipment Or ContainersSTRP Striping

40

5.3 MODIFIERS AND USER DEFINITIONS (Continued) ____ Layer Description ____

STRS Stairs, Escalators And LaddersSUSP Suspended Elements Or EquipmentSWBD Switch BoardsSWCH SwitchesSYMB Symbols, Bubbles And Targets*SHRB Shrubs And BushesSUPL Supply Lines

TEES Main TeesTEXT General Notes & SpecificationsTHER ThermostatsTPTN Toilet PartitionsTREE TreesTTLB Title Block Sheet Name And NumberTURF Lawn Area

UCPT Under Carpet WiringUNDR UndergroundURAC Underground Raceways

WALL Wall LocatedWDWK Woodwork And CabinetsWIRE WiringWKSN Work StationsWHED Window HeaderWATR Water FeaturesWALK Walks (Pedestrian)

The California State University - Faculty...

Documents

Transcript of The California State University - Faculty...