The BNT Nonmetallic Cable Support For Power Manholes and ... · BNT-S942A BNT-S952A BNT-S932A...
Transcript of The BNT Nonmetallic Cable Support For Power Manholes and ... · BNT-S942A BNT-S952A BNT-S932A...
FORM: 052318BA Page 1 of 6
The BNT Nonmetallic Cable Support For Power Manholes and Vaults
BNT Series Nonmetallic Cable Support
Arms Installed in A Nonmetallic Stanchion
US PATENTS - 8,567,734 - 8,596,590 - 8,960,612
Additional information and details are available at
http://www.udevices.com
PRODUCT FEATURESHigh Load CapacityŸ
Can be Used With Existing Steel ŸStanchions or New Nonmetallic
Stanchions
Will Not Rust or CorrodeŸInsulators Not RequiredŸ
Excellent Dielectric PropertiesŸMultiple Arm and Stanchion Ÿ
Lengths Available
Molded from UL Listed Glass ŸReinforced Polymer
NOTES:1) 1 each BNT-H1 humped cotter pin is included with each BNT-P pin.2) Use the BNT-P4 cross pin with existing steel stanchions.3) Use the BNT-P5 cross pin with BNT-S nonmetallic stanchions.
BNT-P5(SEE NOTES 1 & 3)
BNT-P4(SEE NOTES 1 & 2)
BNT-H1(SEE NOTE 1)
BNT-A2
4.859
10.041
BNT-A1
4.043
5.042
BNT-A4
20.021
6.990
4.990
15.039
BNT-A3
3.000 (TYPICAL OF ALL ARMS)
BNT ARMS & PINS
* Concentrated load centered in outermost saddle
RATED ARM CAPACITY
RATED LOAD (LBS)*
CATALOGNUMBER
ARM LENGTH(Inches)
BNT - A1 5.042”
10.041”
15.039”
20.021”
BNT - A2
BNT - A3
BNT - A4
450
400
350
300
FORM: 052318BA Page 2 of 6
1
2
3
4
FSSRM-12-316
FHC316-16-040
FFW316-17-038
FRT-112
.531 ID, 1.188 OD, .125 Thick
SETTING TOOL Use to install FSSRM-12-316Drop-In Anchors
STANCHION MOUNTING HARDWARE
MATERIAL
STEEL
316
STEELSTAINLESS
CATALOGDESCRIPTION
1/2-13 DROP-IN ANCHOR
1/2-13 X 1-1/4” Long
FLAT WASHER
HEXHEAD CAP SCREW
NUMBERITEMNo.
BNT MOUNTING HARDWARE(Drop-in Anchor Installation)
GENERAL INSTALLATION INSTRUCTIONS1. The surface of the concrete wall should be smooth, flat, and plumb.2. Install one fastener set in each of the elongated
stanchion mounting holes.3. Install each drop-in anchor as shown in “Detail No. 1” and as described below: A. Drill a 5/8” diameter hole 2” deep. B. Blow out hole. C. Drive anchor flush to 1/16” below surface of concrete D. Expand anchor with FRT-112 setting tool. Anchor is properly seated when shoulder of setting tool is flush with the top of anchor.4. Install the flat washer and tighten the cap screw5. Assemble arms to stanchion with cross pins and cotter pins.6. Installation drawings that show additional details are included in the UDI general catalog and at http://www.udevices.com.
4
DETAIL No. 1
1
2
3
CONCRETE STANCHION
FLUSH TO 1/16” MAX
DEPTH OF 5/8” DIA HOLE
+1/16”- 0”2”
TENSION Lbs. (kN)
f’c=2000 PSI (13.8 MPa)
3,300 (14.7) 5,840 (26.0) 8,300 (36.9) 4,500 (20.4)
f’c=4000 PSI (27.6 MPa)
f’c=6000 PSI (41.4 MPa)
f’c@2000 PSI (13.8 MPa)
SHEAR Lbs. (kN)
*Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.f’c = Concrete compressive strength
The values in this table are applicable to 1/2 -13 drop-in anchors
Combined Shear and Tension Loading for UDI Drop-In Anchors
Allowable loads for anchors subjected to combined shear and tension forces are determined by the
following equation:(Ps/Pt) + (Vs/Vt) = 1
Ps=Applied tension load Vs=Applied shear load Pt=Allowable tension load Vt=Allowable shear load
ANCHOR LOAD CAPACITYUltimate Shear and Tension Values In Solid Concrete*
GENERAL ANCHOR NOTES:1. Caution: UDI drop-in anchors are
designed to operate properly only when installed with UDI brand FRT setting tools.
2. The use of a 24 to 40 ounce hammer is recommended for expanding UDI drop-in anchors.
3. Anchors should be installed with carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994 specifications.
4. UDI drop in anchors are tested to ASTM E488 and are approved and listed by agencies as required by local building codes.
5 . U D I d r o p - i n a n c h o r s a r e n o t recommended for use in new concrete which has not had sufficient time to cure.
6 . U D I d r o p - i n a n c h o r s a r e n o t recommended for use in light weight masonry such as block or brick.
HEX HEAD CAP SCREW NOTES:1. UDI Type 316 stainless steel cap screws
conform to ASTM 316F593G and ASME B18.2.1.
2. “316F593G” and the manufactures identification number is stamped on the head of each Type 316 stainless steel screw.
3. The manufacturing lot number is marked on each carton of fasteners and has full traceability.
4. Upon request UDI will supply written certification that a given lot of fasteners conforms to the applicable specification.
FORM: 052318BA Page 3 of 6
4
1
4
4
8
12
40
43
35
28
40
36
4.75
4.20
2.12
.40 6.000
4.562
9.375 3.625
3.625
3.625
3.625
3.625
2.188
2.188
2.188
.750
1.003
.826
.649
.924
.845
.025
.025
.025
.002
9.375
9.375
9.375
9.375
4.250
4.250
4.250
.750
4.562
4.562
43
47
33
42
51
40
40
(Inches) (Inches) (Inches)
FSSRM-12-316
FHC316-16-040
FFW316-17-038
BNT-S942A
BNT-S952A
BNT-S932A
BNT-S912A
FRT-112
BNT-S922A
STANDARD STANCHION ORDERING INFORMATIONSTANDARD CARTON
CATALOGQUANTITY LBS
LENGTH WIDTH HEIGHT CUBICFEET
NUMBER
NOTE: Stanchions that accommodate more arms and that have other distances between arms are available. Consult Underground Devices Sales Engineering.
CATALOGNUMBER
STANDARD CARTON
QUANTITY LBS LENGTH (Inches)
WIDTH (Inches)
HEIGHT (Inches)
CUBIC FEET
BNT-A1 10 8 15.250 8.250 4.750 .346
DESCRIPTION
ONE SADDLEARM
BNT-A2 10 16 15.250 13.250 5.500 .643TWO SADDLE ARM
BNT-A3
BNT-A4
10
6
23
21
15.250
20.500
15.250
9.500
7.500
9.500
1.009
1.071
THREE SADDLE ARM
FOUR SADDLE ARM
BNT-P4 10 2 5.750 4.250 4.250 .0604" CROSS PINWITH COTTER PIN
BNT-P5 10 2 5.750 4.250 4.250 .0605" CROSS PINWITH COTTER PIN
BNT-H1 40 .6 3.750 3.125 2.125 .014HUMPED COTTER PIN
NOTES:1) 1 each BNT-H1 humped cotter pin is included with each BNT-P pin.2) Use the BNT-P4 cross pin with existing steel stanchions.3) Use the BNT-P5 cross pin with BNT-S nonmetallic stanchions.
ARM & PIN ORDERING INFORMATION
ORDERING INFORMATION
FORM: 052318BA Page 4 of 6
BNT - S9 STANCHIONS
NOTE: Stanchions that accommodate more arms and that have other distances between arms are available. Consult Underground Devices Sales Engineering and see “BNT Custom Stanchion Installation Drawings” at http://www.udevices.com.
TABLE 1: STANCHION FEATURES & DIMENSIONS
DIMENSIONS(Inches)
L M
QUANTITY OF WALL MOUNTING HOLESSTANCHION CONFIGURATION
QUANTITY OF ARM MOUNTING HOLESDISTANCE BETWEEN ARMSS=STANCHIONCABLE SUPPORT FAMILY
CATALOGNUMBER
D
BNT-S952A
BNT-S942A
BNT-S932A
BNT-S912A
BNT-S922A
9
9
9
9
---
5
4
3
2
1
2
2
2
2
2
50.00 46.00
32.00 28.00
41.00 37.00
23.00 19.00
14.00 10.00
DIS
TAN
CE
BE
TW
EE
N A
RM
MO
UN
TIN
GH
OL
ES
(In
ches
)
MA
X Q
UA
NT
ITY
OF
AR
MS
AC
CO
MM
OD
AT
ED
QU
AN
TIT
Y O
FW
AL
L M
OU
NT
ING
H
OL
ES
FORM: 052318BA Page 5 of 6
A.563
1.000
TOPBNT-S952A
3.8132.500
2.000
4.000
D
LM
SEE DETAIL No. 1ON PAGE 3
The BNT family of cable supports meets power utility needs for a manhole cable support system that is nonmetallic and nonconductive. The non- metallic property is the solution to steel cable rack rust and corrosion problems while the nonconductive properties eliminate cable support grounding and insulator requirements.
A complete nonmetallic solution, consisting of BNT nonmetallic stanchions, arms and cross p ins should be se lected for new and replacement installations. Since BNT arms mate with many existing steel stanchions, retrofitting of existing manholes can be accomplished by initially changing out the steel arms with BNT arms. The existing steel stanchions may be replaced, as necessary, at a later date.
Arm installation is safe and simple - the arms are secured in place with nonmetallic pins, allowing for installation and removal of the arms without disturbing any cable.
Due to the extreme strength and rigidity of the BNT stanchions, most installations require only two bolts to secure a stanchion to the manhole wall.
BNT arms and stanchions have loading capacities comparable to similar heavy duty steel cable racks.
CLAIMS:
TERMS:
LIMITEDWARRANTY:
RETURNGOODSPOLICY:
Net 30 days - $100.00 minimum net billing. All prices FOB our factory or warehouse location with freight to be charged directly by the carrier.
Claims for damages or shortages shall first be processed with carrier by consignee.
A 25% re-stocking charge will be made on orders returned, transportation prepaid, to the original shipping point following authorization from UNDERGROUND DEVICES, INC. Authorization will be granted only under the conditions that the quantity to be returned does not exceed 10% of the quantity ordered, the goods are in saleable condition in the original cartons and the request for return is made within 30 days of the shipping date.
UNDERGROUND DEVICES, INC. Warrants to the original purchaser that the goods manufactured by it are free from defects in materials and workmanship for a period of one year from the date of purchase. Consequences of improper selection or installation of UNDERGROUND DEVICES products on any application over any period of time is the sole responsibility of the Purchaser or User. UNDERGROUND DEVICES liability is limited to replacement of, or credit for, defective products. UNDERGROUND DEVICES, INC. WILL IN NO EVENT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
BNT Nonmetallic Cable Support Arms Installed In An existing Steel Stanchion
FORM: 052318BA Page 6 of 6
For a sample:Please call us at (800)800-2118 or
Send an email to: [email protected]
FREE
NORTHBROOK, ILLINOIS 60062420 ACADEMY DRIVE
Phone: 847-205-9000 Fax: 847-205-9004 www.udevices.com