TEST REPORT PRODUCT UPGRADING AND RECYCLING...1 Report No.: 13-04-QAR-006 TEST REPORT PRODUCT...
Transcript of TEST REPORT PRODUCT UPGRADING AND RECYCLING...1 Report No.: 13-04-QAR-006 TEST REPORT PRODUCT...
1
Report No.: 13-04-QAR-006
TEST REPORT
PRODUCT UPGRADING AND RECYCLING
Report No. : 13-04-QAR-006
Approved by
(Signature) : Date of issue : 2013/ 05/ 16
Contents : 33 Pages
Testing Laboratory Name : Electronics Testing Center, Taiwan.
Address : No. 8, Lane 29, Wenming Rd., Guishan Shiang, Taoyuan
County, 33383 Taiwan, R.O.C.
Subcontract Lab. : Environmental Protection and Industrial Safety/ Hygiene
Department
Address : No. 8, Lane 29, Wenming Rd., Guishan Shiang, Taoyuan
County, 33383 Taiwan, R.O.C.
Applicant's Name : VXL INSTRUMENTS LTD
Address
: HOUSE OF EXCELLENCE NO.17 ELECTRONICS CITY
HOSUR RD BANGALORE, KA 560100 INDIA
Test Specification
Standard : WEEE (2012/19/EU)
Test procedure : None
Non-standard test method : None
Type of Test Object : Thin Client
Trademark
:
Factory : VXL Instruments Limited
Model and/ or type reference : Itona Md series
Series Model : Itona M series
Rating(s) : ----
1. Selective treatment material/component of waste electrical and electronic equipment is
removed in accordance with WEEE Directive Annex VII and 75/442/EEC article.
2. The results shown in this test report refer only to the sample(s) tested.
2
Content of WEEE Compliance Assessment Report
Item Content
1
Product Information
In this section, it states which category your product belongs in accordance with
2012/19/EU WEEE Directive Annex I, and describes the product in brief, such as
product layout, weight, etc.
2
Dismantling Process and Special Handling Needs
This disassembly process is to optimize dismantling procedure to the least steps, costs
and manpower. Also it ensures the selective treatment for materials and components
of WEEE Annex VII are removed accordingly.
The disassembly process shows graphic instructions with pictures taken during the
dismantling procedures step by step.
3 3R Assessment
Assess the product in recycling performance in accordance with reuse, recycling &
recovery targets in the WEEE Directive and for EPEAT
4 WEEE Annex VII (components with special handling needs)
In this section, we will show the dismantling procedure for the selective treatment of
materials/components with special handling needs of WEEE Annex VII
Notes:
1. ETC WEEE Compliance Assessment Report is developed and based on ECMA 341 Design
for Environment standard, VDI 2243 Design for Recycling standard and CECED Guidance
on information for treatment facilities.
2. The content of this report is for references, but not for advertising publicity or other
commercial purpose.
3. The assessment report shall not be reproduced, except in full with the written approval of
ETC.
Address: No. 8, Lane 29, Wenming Rd., Guishan Shiang, Taoyuan County, 33383 Taiwan,
R.O.C.
TEL: 886-3-328-0026 ext 627
FAX: 886-3-327-6176
ELECTRONICS TESTING CENTER, TAIWANENVIRONMENTAL PROTECTION AND INDUSTRIAL SAFETY/HYGIENE DEPARTMENT
3
ACKNOWLEDGEMENT ETC 3R compliance assessment report is accepted and recommended as a reference for
recycling electrical and electronic equipment by the following recyclers and compliance schemes
in the EU member states:
Member State Compliance
Scheme/Recycler Logo
Spain ECOASIMELEC
Germany EGR
France Eco-systèmes
United Kingdom VALPAK
Italy Re.Media
4
Index
1. Product Information...............................................................................................................5
- WEEE Category..................................................................................................................5
- General Information ............................................................................................................6
2. Dismantling Process and Special Handling Needs.............................................................7
Accessories ..........................................................................................................................9
Itona Md series ................................................................................................................... 11
Adapter ...............................................................................................................................17
Wireless USB......................................................................................................................20
Card Reader .......................................................................................................................21
- Part List-Package .............................................................................................................22
- Part List-Accessories ........................................................................................................22
- Part List-Itona Md series...................................................................................................22
- Part List-Adapter...............................................................................................................23
- Part List-Wireless USB .....................................................................................................23
- Part List-Card Reader.......................................................................................................23
- Joint Technology Information-Package .............................................................................24
- Joint Technology Information-Accessories........................................................................24
- Joint Technology Information-Itona Md series...................................................................25
- Joint Technology Information-Adapter ..............................................................................26
- Joint Technology Information-Wireless USB.....................................................................26
- Joint Technology Information-Card Reader.......................................................................26
3. 3R Assessment ....................................................................................................................27
4. WEEE Annex VII (components with special handling needs) ..........................................28
5. Plastic Composition Analysis .............................................................................................29
- Test Method ......................................................................................................................29
- Test Results ......................................................................................................................30
6. Product Specification ..........................................................................................................31
5
1. Product Information
- WEEE Category
Category Recovery
Rate Recycling
Rate
1.Large household appliance 80 % 75 %
2.Small household appliance 70 % 50 %
*** 3.IT and telecommunications equipment 75 % 65 %
4.Consumer equipment and Photovoltaic panels 75 % 65 %
5.Lighting equipment 70 % 50 %
6.Electrical and electronic tools (with the exception of large-scale stationary industrial tools)
70 % 50 %
7.Toys, leisure and sports equipment 70 % 50 %
8.Medical devices(with the exception of all implanted and infected products)
70 % 50 %
9.Monitoring and control instrument 70 % 50 %
10.Automatic dispensers 80 % 75 %
The table above shown which category your product belong to. The row revised by blue color is
the right category the product in. The rate of recovery and the rate of reuse and recycling of the
product meet the minimum rate stipulated by WEEE Directive (2012/19/EU). PS:Minimum recovery targets and Applicable date refered to Annex V of 2012/19/EU[WEEE Directive(recast)]
6
- General Information
Features
This thin client is equipped with a Gigabit Ethernet port that provides instant connection to
multi-user Windows NT application servers. Display Port, DVI-I, USB and PS/2 compatible
keyboard/Mouse ports are available for quick set up and use.
Fig 1: Product information on package
Fig 2: Product photo
7
2. Dismantling Process and Special Handling Needs Items marked in Red (noted as Annex VII part) are substances, preparations, or components with special handling needs, due to the toxicity potential of elements contained therein.
: General Part
: Annex VII Part
: Separate Direction
Separate 2: Take Out (Put Together × 1) the object from part 1.
Separate 1: Take Out (Put Together × 1) the Accessories.
Take Out
Take Out
Separate 1
Separate 2
1
8
Separate 3: Take Out (Put Together × 2) the part 2 from Itona Md series, and remove
(Put Together × 1) the bag.
: General Part
: Annex VII Part
: Separate Direction
Take Out
Remove
2
Separate 3
Itona Md series
9
Accessories
Separate 1: Take Out (Put Together × 1) the Adapter, and remove (Put Together × 1) the
bag.
Separate 2: Take Out (Put Together × 1) the part 1, and remove (Put Together × 1) the
bag.
: General Part
: Annex VII Part
: Separate Direction
RemoveTake Out
Remove
Take Out
Separate 1
Adapter
Separate 2
1
10
Separate 3: Take Out (Put Together × 1) the part 2 from 3 by one person.
: General Part
: Annex VII Part
: Separate Direction
Take Out
Separate 32
3
11
Itona Md series
Separate 1: Unscrew (Cross × 2) all screws to take out the part 1 by one person.
Separate 2: Remove (Snap Fit × 2) the part 2 by one person.
: General Part
: Annex VII Part
: Separate Direction
Unscrew
Take Out
Both Sides
Remove
1 Separate 1
2
Separate 1
1
2
Separate 2
Separate 2
12
Separate 3: Remove (Snap Fit × 1) the part 3 by one person.
: General Part
: Annex VII Part
: Separate Direction
Remove
3
Separate 3
13
Separate 5: Unscrew (Cross × 2) all screws, and cut (Wire Connection × 2) to take out
the Card Reader.
: General Part
: Annex VII Part
: Separate Direction
Take Out
Separate 4: Take Out (Put Together × 1) the Wireless USB.
Take Out
Unscrew
Cut
Separate 4
Separate 5
Wireless USBCard Reader
14
Separate 7: Unscrew (Cross × 2) all screws to take out the part 4 from 5.
: General Part
: Annex VII Part
: Separate Direction
Take Out
Unscrew
Separate 6: Unscrew (Cross × 1) the screw, and cut (Wire Connection × 8) to take out
the object.
Unscrew
Cut Take Out
4
Separate 7
Separate 6
5
15
Separate 8: Unscrew (Cross × 2) all screws, and cut (Wire Connection × 2) to take out
the part 6.
Separate 9: Unscrew (Cross × 6) all screws to take out the part 7 by one person.
: General Part
: Annex VII Part
: Separate Direction
Unscrew
Cut Take Out
Unscrew
Take Out
Separate 8
Separate 9
7
6
16
Separate 10: Cut (Wire Connection × 1) to take out the part 8.
Separate 11: Unscrew (Cross × 6) all screws, and cut (Wire Connection × 2) to take out
the part 9,10 from 11.
: General Part
: Annex VII Part
: Separate Direction
Take Out
Unscrew & Cut
Take Out
Separate 11
8
Separate 10
9
10
11
Cut
Both Sides
17
Adapter
Separate 1: Heating and cut (Extrusion Coat × 1) to remove the part 1 by one person.
Separate 2: Take Out (Put Together × 1) the part 2, and rip (Glued Joint × 1) the label.
: General Part
: Annex VII Part
: Separate Direction
Heating & Cut Remove
RipTake Out
Separate 1
Separate 2
1
2
18
Separate 3: Cut (Soldered Joint × 1) to take out (Glued Joint × 1) the part 3.
Separate 4: Take Out (Put Together × 1) the part 4.
: General Part
: Annex VII Part
: Separate Direction
Cut
Take Out
Take Out
Separate 3
3
4
Separate 4
19
Separate 5: Cut (Soldered Joint × 2) to take out the part 5 from 6, and cut (Wire
Connection × 1) wire.
: General Part
: Annex VII Part
: Separate Direction
Take Out
Cut Cut
5
Separate 5
6
20
Wireless USB
Separate 1: Pry (Snap Fit × 1) to take out the part 1 by one person.
Separate 2: Take Out (Put Together × 1) the part 2 from 3.
: General Part
: Annex VII Part
: Separate Direction
Separate 1
3
1
Separate 2
2
Take OutCut
Take Out
21
Card Reader
Separate 1: Unscrew (Cross × 2) all screws to take out the part 1, and rip (Glued Joint
× 1) the label by one person.
Separate 2: Take Out (Put Together × 1) the part 2 from 3.
: General Part
: Annex VII Part
: Separate Direction
Separate 1
1
Separate 2
2
3
RipTake OutUnscrew
Take Out
22
- Part List-Package
No. Name Material Quantity Weight(g) Characteristic Mark
G1 Box Cardboard 1 292 Recyclable
G2 Foam LDPE 2 275 Recyclable
- Part List-Accessories
No. Name Material Quantity Weight(g) Characteristic Mark
G1 DVI-I - VGA Dongle Plastic
Complex 1 30 Recyclable NA
G2 Pedestal ABS 1 31 Recyclable
G3 Box Cardboard 1 115 Recyclable
- Part List-Itona Md series
No. Name Material Quantity Weight(g) Characteristic Mark
G1 Top & Bottom Strip ABS 2 48 Recyclable
G2 Side Panels ABS 2 209 Recyclable
G3 Front Bezel ABS 1 47 Recyclable
A4 PCB - Front
Assembly PCB Complex 1 26 Recyclable NA
G5 PCB Cover Metal 1 44 Recyclable NA
G6 Speaker Plastic
Complex 1 4 Recyclable NA
G7 Aluminum Top
Cover Metal 1 142 Recyclable NA
A8 Battery ---- 1 3 Recyclable NA
G9 I/O Cover Metal Complex 1 82 Recyclable NA
A10 PCB - Mother Board
Assembly PCB Complex 1 458 Recyclable NA
G11 Case Metal 1 221 Recyclable NA
---- Screw(Cross) Metal 21 6 Recyclable NA
---- Wires & Cables ---- ---- 38 Recyclable NA
23
- Part List-Adapter
No. Name Material Quantity Weight(g) Characteristic Mark
G1 Top Cover Plastic 1 20 Recyclable NA
G2 Bottom Cover Plastic 1 19 Recyclable NA
G3 Heat Sink Metal 1 14 Recyclable NA
A4 Mylar Plastic 1 3 Recyclable NA
A5 Capacitor Capacitor
Complex 1 12 Recyclable NA
A6 PCB PCB Complex 1 91 Recyclable NA
---- Wires & Cables ---- ---- 53 Recyclable NA
- Part List-Wireless USB
No. Name Material Quantity Weight(g) Characteristic Mark
G1 Top Cover Plastic 1 1 Recyclable NA
A2 PCB PCB Complex 1 3 Recyclable NA
G3 Bottom Cover Plastic 1 1 Recyclable NA
- Part List-Card Reader
No. Name Material Quantity Weight(g) Characteristic Mark
G1 Bottom Cover Plastic 1 6 Recyclable NA
A2 PCB PCB Complex 1 7 Recyclable NA
G3 Top Cover Plastic 1 7 Recyclable NA
---- Screw(Cross) Metal 2 1 Recyclable NA
24
- Joint Technology Information-Package
No. Separate Joint Technology Quantity Dismantling Tool
1. Separate 01 Put Together 1 Without Tool
2. Separate 02 Put Together 1 Without Tool
3. Separate 03 Put Together 3 Without Tool
Total ---- ---- Put Together 5 Without Tool
PS: Without Tool main handle
- Joint Technology Information-Accessories
No. Separate Joint Technology Quantity Dismantling Tool
1. Separate 01 Put Together 2 Without Tool
2. Separate 02 Put Together 2 Without Tool
3. Separate 03 Put Together 1 Without Tool
Total ---- ---- Put Together 5 Without Tool
PS: Without Tool main handle
25
- Joint Technology Information-Itona Md series
No. Separate Joint Technology Quantity Dismantling Tool
1. Separate 01 Screw(Cross) 2 Screwdriver (Cross)
2. Separate 02 Snap Fit 2 Without Tool
3. Separate 03 Snap Fit 1 Without Tool
4. Separate 04 Put Together 1 Without Tool
Screw(Cross) 2 Screwdriver (Cross) 5. Separate 05
Wire Connection 2 Pliers
Screw(Cross) 1 Screwdriver (Cross) 6. Separate 06
Wire Connection 8 Pliers
7. Separate 07 Screw(Cross) 2 Screwdriver (Cross)
Screw(Cross) 2 Screwdriver (Cross) 8. Separate 08
Wire Connection 2 Pliers
9. Separate 09 Screw(Cross) 6 Screwdriver (Cross)
10. Separate 10 Wire Connection 1 Pliers
Screw(Cross) 6 Screwdriver (Cross) 11. Separate 11
Wire Connection 2 Pliers
Total Screw (Cross) 21 Screwdriver (Cross)
Put Together 1 Without Tool
Snap Fit 3 Without Tool ---- ----
Wire Connection 15 Pliers
PS: Without Tool main handle
26
- Joint Technology Information-Adapter
No. Separate Joint Technology Quantity Dismantling Tool
1. Separate 01 Extrusion Coat 1 Hot Air Blower & Knife
Put Together 1 Without Tool 2. Separate 02
Glued Joint 1 Without Tool
Soldered Joint 1 Pliers 3. Separate 03
Glued Joint 1 Without Tool
4. Separate 04 Put Together 1 Without Tool
Soldered Joint 2 Pliers 5. Separate 05
Wire Connection 1 Pliers
Total Put Together 2 Without Tool
Wire Connection 1 Pliers
Glued Joint 2 Without Tool
Soldered Joint 3 Pliers
---- ----
Extrusion Coat 1 Hot Air Blower & Knife
PS: Without Tool main handle
- Joint Technology Information-Wireless USB
No. Separate Joint Technology Quantity Dismantling Tool
1. Separate 01 Snap Fit 1 Chisel
2. Separate 02 Put Together 1 Without Tool
Total Snap Fit 1 Chisel
---- ---- Put Together 1 Without Tool
PS: Without Tool main handle
- Joint Technology Information-Card Reader
No. Separate Joint Technology Quantity Dismantling Tool
Screw(Cross) 2 Screwdriver (Cross) 1. Separate 01
Glued Joint 1 Without Tool
2. Separate 02 Put Together 1 Without Tool
Total Screw(Cross) 2 Screwdriver (Cross)
Glued Joint 1 Without Tool ---- ----
Put Together 1 Without Tool
PS: Without Tool main handle
27
3. 3R Assessment
Product Main Material Identification
Item Main Material Weight(g) Characteristic Percent(%)
1 Metal Total 510 Recyclable 22.1
Plastic 423 Recyclable 18.3 2
Brominated Plastic 3 Recyclable 0.1
3 Wires / Cables 91 Recyclable 3.9
4 Glass (non CRT) 0 Recyclable 0.0
Other Misc. materials 0 Recovery 0.0 5
Packaging materials 682 Recyclable 29.5
6 Annex VII Materials 600 Recyclable 26.1
Total weight : 2309 100
Recycling Rate (Reuse + Recycle) : 2180.0 94.4
Energy Recovery : 105.3 4.6
Recovery Rate (Reuse + Recycle + Energy Recovery) : 2285.3 99.0
WEEE Compliance
Item Weight(g) %
Recycle 2180.0 94.4
Waste to Energy
105.3 4.6
Landfill 23.7 1.0
Product - WEEE Recycling Assessment
4.6%
94.4%
Landfill ~ 1.0%
Recyclable Waste to Energy
Landfill
28
4. WEEE Annex VII (components with special handling needs) Items in this table contain materials with special handling needs. However, the product do not include any “nonstandard or new” substances or technologies.
Itona Md series
No. Name Quantity Weight(g) Annex II Materials Page
A4 PCB - Front
Assembly 1 26 Printed Circuit Assemblies > 10 cm2 14
A8 Battery 1 3 Batteries 16
A10 PCB - Mother Board
Assembly 1 458 Printed Circuit Assemblies > 10 cm2 16
Adapter
No. Name Quantity Weight(g) Annex II Materials Page
A4 Mylar 1 3 Plastic containing Br flame
retardants 18
A5 Capacitor 1 12 Electrolite Capacitors over 2.5 cm
high & diameter 19
A6 PCB 1 91 Printed Circuit Assemblies > 10 cm2 19
Wireless USB
No. Name Quantity Weight(g) Annex II Materials Page
A2 PCB 1 3 Printed Circuit Assemblies > 10 cm2 20
Card Reader
No. Name Quantity Weight(g) Annex II Materials Page
A2 PCB 1 7 Printed Circuit Assemblies > 10 cm2 21
29
5. Plastic Composition Analysis
- Test Method
Analytical
Substance Equipment Methods
XRF Screening
Action Limit(ppm)
Pb ED-XRF IEC 62321 Ed1: 2008 700
Cd ED-XRF IEC 62321 Ed1: 2008 70
Hg ED-XRF IEC 62321 Ed1: 2008 700
Cr ED-XRF IEC 62321 Ed1: 2008 700
Br ED-XRF IEC 62321 Ed1: 2008 300
30
- Test Results
Tested Part No. XRF Screening
(ppm)
Tested Part
Description Tested Part Photo
Cd: 0.0
Pb: 1.9
Hg: 8.3
Br: 27.8
13-04-QAR-006-1
Cr: 8.8
Top Cover
(Wireless USB)
Cd: 0.0
Pb: 0.1
Hg: 6.9
Br: 22.7
13-04-QAR-006-2
Cr: 9.3
Top Cover
(Card Reader)
Cd: 0.0
Pb: 0.2
Hg: 0.2
Br: 9.1
13-04-QAR-007-1
Cr: 25.4
Side Cover
(Itona Md+ series)
Cd: 0.0
Pb: 0.6
Hg: 0.5
Br: 14.1
13-04-QAR-007-2
Cr: 55.8
Front Cover
(Itona Md+ series)
Cd: 0.0
Pb: 1.2
Hg: 6.5
Br: 77.3
13-04-QAR-007-3
Cr: 8.8
Bottom Cover
(Adapter)
Cd: 0.9
Pb: 0.0
Hg: 0.0
Br: 51098.6
13-04-QAR-007-4
Cr: 10.1
Mylar
(Adapter)
Note:
1. ppm : mg/kg (0.1% = 1000ppm)
31
6. Product Specification
Thin Client
Itona Md series Itona M series
Chipset
32
33
Adapter