TeleHybrid - Kilpack

TeleHybrid

Installation andOperations Manual

Gentner Communications Corporation is committed to protecting theenvironment and preserving our natural resources.

This manual has been printed entirely on recycled paper.

This equipment complies with the requirements of the EU guidelines:

89/336/EEC “Electromagnetic Compatibility”

73/23/EEC “Electrical operating material for use within specificvoltage limits”

Conformity of the equipment with the above guidelines is attested by the CE mark.

© Copyright 1996 Gentner Communications Corporation. All rights reserved. No part ofthis manual may be reproduced in any form or by any means without written permissionfrom Gentner Communications Corporation. Printed in the United States of America.Original version, 12/95. Gentner Communications Corporation reserves specificationprivileges. Information in this manual is subject to change without notice.

TeleHybrid Installation and Operations ManualGentner Part No. 800-006-010 (Rev. 2.10)December 1996

Manual Development: Bill Kilpack

Artwork and IIlustrations: Mike Greenhalgh

CopyrightInformation

ContentsIntroduction 1Warranty Registration 1Unpacking 2Features and Benefits 3Before You Install 4

Power Requirements 4Telephone Line Requirements 4Telephone Set Requirements 4Equipment Placement 4

Installation 5Completed Installation 5Step 1 5Step 2 6Step 3 6Step 4 7Step 5 (Record Option) 7

One-Time Setup 7Step 1 — Slide Control Setup 7Step 2 — Switch Location 8Step 3 — Compatibility/Sensitivity Setup 8Step 4 — Handset Operational Check 9Step 5 — Receive Audio Check 9Step 6 — Send Audio Adjustment 9

SoundCheck Setup 10Step 1 — Studio Preparation 10Step 2 — Power Down the TeleHybrid 10Step 3 — Call Quiet Line 11Step 4 — Adjust Send Audio 11Step 5 — Exit SoundCheck Mode 12Step 6 — Verify SoundCheck Settings 12

Operation 13Making calls with the TeleHybrid 13Answering calls with the TeleHybrid 13Using existing telephone features 13Hanging up a call 13

Troubleshooting 14Specifications 15Warranty 17FCC Part 15 Compliance 18FCC Part 68 Compliance 18IC Compliance 19Safety Information 20Appendix A 21

TeleHybrid Installation and Operations Manual Page iii

Technical or Setup Assistance • Telephone: 800.945.7730 (USA)801.975.7200 (worldwide) • Worldwide Web @ http://www.gentner.com

List of Figures

Figure 1. Equipment diagram 2Figure 2. Properly installed TeleHybrid system 5Figure 3. Telephone cable installation 5Figure 4. Handset modular line installation 6Figure 5. RJ45/XLR cable connection/pinout 6Figure 6. Power module hook up 7Figure 7. Optional tape recorder hook up 7Figure 8. TeleHybrid slide control 7Figure 9. Compatability and sensitivity switches 8Figure 10. Compatability and sensitivity set up 8Figure 11. Handset placement with TeleHybrid 9Figure 12. Sensitivity switch adjustment 9Figure 13. Power disconnection 10Figure 14. Sensitivity switch adjustment 11Figure 15. TeleHybrid without mix-minus 21Figure 16. TeleHybrid-to-video CODEC 21Figure 15. News-edit configuration 22Figure 16. TeleHybrid with teleconferencer 22

Page iv TeleHybrid Installation and Operations Manual


TeleHybrid Installation and Operations Manual Page 1


Congratulations on purchasing the TeleHybrid. TheTeleHybrid allows you to hold a completelyinteractive talkshow, radio or television contest, orteleconference meeting, no matter what type oftelephone you have. With the TeleHybrid, you candirectly connect external audio equipment to yourexisting telephone and maintain all normaltelephone functions.

This manual explains how to install, set up andoperate the TeleHybrid. It also provides instructionson how to resolve minor technical problems, shouldany arise. An appendix is provided to illustratedifferent TeleHybrid applications.

If you need additional information on how to install,set up or operate your TeleHybrid, please contact usat Gentner Communications at the location notedbelow. We welcome and encourage your commentsso we can continue to improve our products andbetter serve your communication needs.

Gentner Communications CorporationSales and Technical Assistance

1825 Research WaySalt Lake City, Utah 84119

TEL: Worldwide (801) 975-7200 In U.S.A. (800) 945-7730FAX: Worldwide (801) 977-0087 In U.S.A. (800) 933-5107FAX-On-Demand 24-Hour Information Service (800) 695-8110

Worldwide Web Page @ http:\\www.gentner.com

Please register your TeleHybrid by completing theself-addressed, postage prepaid warranty registrationcard and return it to Gentner Communications bymail. You may also FAX it to the above listed faxnumber or call Gentner Communications. Whenyour product is properly registered, GentnerCommunications will be able to serve you bettershould you require technical assistance or desire toreceive upgrades, new product information, etc.

Introduction

WarrantyRegistration

TeleHybrid Installation and Operations Manual


Ensure that the following equipment was receivedwith your shipment:

SHIPPING NOTE:Gentner Communications is not responsible forproduct damage incurred during shipment. You mustmake claims directly with the carrier. Inspect yourshipment carefully for obvious signs of damage. Ifthe shipment appears to be damaged, retain theoriginal boxes and packing material for inspectionby the carrier. Contact your carrier immediately.

Unpacking

Figure 1. Equipmentdiagram



Simple, easy professional telephone interfacebetween your phone and external audio equipment

Telephone compatibility that allows you to use yourcurrent telephone capabilities (i.e. hold, transfer,conference, speed-dial, last dial, redial, etc.)

Compatibility with digital and analog telephones

Does not require the installation of a dedicatedtelephone line

Full-duplex operation allows participants to talk andlisten simultaneously

Digital technology for unsurpassed audio quality

Tape recorder connectivity to record your call

Easy to install and operate

Professional technical support for reliable assistancewith setup and operation

Distribution support near your location for sales andassistance

Features andBenefits



The TeleHybrid is designed to work with digital andanalog telephones. This unique design is a first inthe industry. To maximize your audio quality, werecommend that you prepare your site by taking thefollowing factors into consideration:

Power Requirements

The TeleHybrid will accommodate voltagerequirements of 120Vac, 60Hz, 23W with thesupplied power module. It will alsoaccommodate other voltage requirements withan optional power transformer.

Telephone Line Requirements

Unlike other telephone hybrids, the TeleHybridconnects directly to existing digital and analogtelephone sets. A dedicated analog telephoneline is not needed to operate your TeleHybrid.

Telephone Set Requirements

The TeleHybrid will operate with multiline andsingle line telephone sets that have a detachablehandset cord at the telephone base. TheTeleHybrid will not work with “Princess” or“Trimline” style telephones that have thedialing pad built into the handset. The dialingpad must be located on the telephone base, noton the telephone handset.

Equipment Placement

The TeleHybrid should be placed next to thetelephone set and virtually anywhere within 12feet of the equipment you will be connecting to.

Before YouInstall



The TeleHybrid connects directly to your existingtelephone set so that you can maintain all normaltelephone functions. Follow these step-by-stepinstructions to install your TeleHybrid:

Completed Installation

The following drawing shows a properly set upTeleHybrid system. For a complete systemdiagram, refer to Appendix A (Pages 19-20).

Step 1

Unplug the handset cord from the base of yourtelephone set. Plug the handset cord into theTeleHybrid jack labeled HANDSET.

Installation

Figure 2. Properly installedTeleHybrid system set up witha telephone

Figure 3. Telephone cableinstallation key pullout (top);handset cable installation(bottom)



Step 2

Plug one end of the supplied 16-inch or optional32-inch flat handset cable into the telephonehandset jack. Plug the other end of cable intothe TeleHybrid jack labeled PHONE.

Step 3

Plug the RJ45/XLR cable from the supplied 12-foot connection cable into the TeleHybrid jacklabeled CONSOLE ONLY. The two XLRs arefor connecting to your external equipment. TheMale XLR contains caller audio. The FemaleXLR contains the audio you will send to thecaller. Refer to the appendix for variousapplication setups using the TeleHybrid.

Figure 4. Handset modularline installation

Figure 5. RJ45/XLR cableconnection/pinout

InstallationContinued



Step 4

Plug the white end of the power module with theNOTCH SIDE labeled UP into the TeleHybridjack labeled 19 VDC IN. Plug the other end ofthe power module into an electrical poweroutlet. A power-up message, designed to assistin the adjustment of the receive/caller levels ofthe TeleHybrid, is played when power is applied.

Step 5 (Record Option)

To record your audioconference, connect a taperecorder (not provided) to the TeleHybrid jacklabeled REC. A standard phono cable istypically supplied with most tape recorders.

Because telephones are different, you will need tomake a one-time setup to accommodate yourparticular type of telephone. Follow these step-by-step procedures:

TELEPHONE VOLUME NOTE:For telephones that have handset volume control, setthe telephone handset volume at a normal listeninglevel prior to adjusting the TeleHybrid.

Step 1 — Slide Control Setup

Locate the slide control on the bottom of theTeleHybrid. Set the slide control to position 1.

Figure 6. Power module hookup

Figure 7. Optional taperecorder hook up

One-TimeSetup

Figure 8. TeleHybrid slidecontrol



Step 2 — Switch Location

Locate the slide cover on the right side of theTeleHybrid. Slide open the cover to reveal thetelephone compatibility and sensitivity switches.

Step 3 - Compatibility and Sensitivity Setup

Determine the appropriate settings for yourparticular telephone using the followingdiagram. Set the compatibility and sensitivityswitches according to your telephone type.

One-Time SetupContinued

Figure 9. Compatability andsensitivity switches

Figure 10. Compatability andsensitivity set up



Step 4 - Handset Operational Check

Pick up the handset and listen for a dial tone. Ifyou hear a dial tone, go to step 5; if you do nothear a dial tone, verify Installation Steps 1-4(See Pages 5-7.) and check your phone forproper connections.

Step 5 - Receive Audio Check

Make certain the XLRs are connected to yourexternal equipment properly. Also verify thatyour external equipment is in the properoperating mode to receive audio from and tosend audio to the TeleHybrid.

To communicate with the distant locationthrough the TeleHybrid and your externalequipment, place the handset on the TeleHybridpad.

With the TeleHybrid activated, listen for dialtone. If you hear a dial tone, go to Step 6, SendAudio Adjustment (See below.); if you do nothear a dial tone, verify One-Time Setup Steps 1-3 (Pages 8-9).

Step 6 - Send Audio Adjustment

Place a call and activate your TeleHybrid toverify the send level.

If your level is too high (distorted), changesensitivity switch 4 located behind the sideaccess panel to the ON position.

To fine adjust the send level use the slide controllocated on the bottom of the TeleHybrid. If yourlevel is too low, adjust the slide control towardposition 8 until you reach the proper send level.If your level is too high, move the slide towardposition 1.

Figure 11. Handset placementto activate TeleHybrid

Figure 12. (R) Sensitivityswitch adjustment; (L) Finetuning the send level with theslide control



In order to maximize the performance of theTeleHybrid, keep the slide control as low aspossible while still maintaining a comfortableaudio level at the distant location.

CUSTOMER SERVICE NOTE:Gentner Communication Corporation is dedicatedto providing the best customer service. If you haveany problems or questions, please call us at:(800) 945-7730 or (801) 975-7200.

In some situations, the send-audio level (from you tothe caller) will need adjustment for optimumTeleHybrid performance. This is caused by factorssuch as the proximity of your facility to thetelephone central office and/or the type of telephonesystem you have installed in your building. To assistin sound-level adjustments, the TeleHybrid is nowequipped with SoundCheck.

SoundCheck operates based on the idea that when atelephone line is driven too hard, it will start todistort the returned audio. SoundCheck provides abuilt-in distortion analyzer to detect this, enablingyou to set up for the maximim level possible withoutcompromising your audio quality.

To perform a SoundCheck setup, follow these step-by-step instructions:

Step 1 — Studio Preparation

Ensure that the male XLR (J2) is connected toyour studio audio monitoring system, and turndown the volume on the audio amplifierconnected to your monitor speakers.

Step 2 — Power Down the TeleHybrid

Remove the DC POWER connector from therear of the TeleHybrid to power it down.

One-Time SetupContinued

SoundCheckSetup

Figure 13. Powerdisconnection



Step 3 — Call Quiet Line

Pick up your telephone handset and call1-800-283-5330 (a quiet line used for setup), ora quiet line at your site. When you hear silenceat the other end, set the handset down on theTeleHybrid, and plug back in the DC POWERconnector, restoring power to the TeleHybrid.SoundCheck should now be enabled.

Step 4 — Adjust Send Audio

Listening to your studio’s audio monitoringsystem, interpret the tone that is being emittedon your monitor speakers, and adjust theTeleHybrid’s SEND AUDIO adjustment.

Beeping: signal level too low, increase SENDAUDIO

Constant: signal level too high, decrease SENDAUDIO

The desired level should be at the transitionpoint between the beeping and constant tone.

If you cannot adjust to this transition point,change sensitivity dip switch 4 (on the right sideof the TeleHybrid) UP (ON) for all telephonetypes being used, except for the Seimens Dyad,Junior Dyad and Digit 260 Console. If usingone of these three telephone types, changesensitivity dip switch 4 DOWN (OFF).

DIGITAL/ANALOG SYSTEM NOTE:The transition point should be easy to find if using adigital telephone system (distortion for anoverdriven digital line is dramatic). However, ifconnected to an analog telephone system, thetransition point may take a little longer to locate(the distortion generated on an overdriven analogline is much gentler).

Figure 12. (R) Sensitivityswitch adjustment; (L) Finetuning the send level with theslide control



Step 5 — Exit SoundCheck Mode

Once the transition point has been located, exitSoundCheck set-up mode by removing handsetfrom the TeleHybrid, disconnecting the DCPOWER connector, waiting a few seconds, thenplugging the DC POWER connector back in.Powering down the TeleHybrid will not resetsettings made with SoundCheck. Disconnectfrom the quiet line.

Step 6 — Verify SoundCheck Settings

Make several test calls to different locations toevaluate the TeleHybrid’s performance. Ifconnected on an exceptionally clean line, theaudio level may actually need to be adjusteddown slightly from the settings indicated bySoundCheck.

SoundCheck SetupContinued



Operating the TeleHybrid is practically identical tooperating your telephone because it uses yourexisting telephone functions.

Making calls with the TeleHybrid

Pick up your handset from the telephone cradleand dial out as normal. Place the handset on theTeleHybrid pad. The TeleHybrid will functionautomatically.

Answering calls with the TeleHybrid

Pick up your handset from the telephone cradleand answer the call as normal. After thetelephone call has been established, place thetelephone handset on the TeleHybrid pad orimmediately place the handset on theTeleHybrid pad after answering the call. TheTeleHybrid will function automatically.

Using existing telephone features

To use your normal telephone functions (i.e. puta call on hold, transfer a call, access additionallines, conference additional lines, hold a privateconversation) the handset can be either placedon the TeleHybrid or picked up and used asnormal.

Hanging up a call

Place the handset on the telephone handsetcradle.

POWER FAILURE NOTE:If you experience a power failure or power bump,you will not lose your call. The caller will be backon the handset. Once power is restored, simply pickup the handset and replace it on the on theTeleHybrid to restore your call.

Operation



Symptom

There is no dial tonethrough the system

The audio level receivedat the distant location istoo low or too high

The system sounds“scratchy” or isproducing excessivenoise

The system squeals orproduces feedback

Probable Cause

The One-Time Setupconfiguration isimproperly set

The send audio volumeis set too low or toohigh

There is a badtelephone-lineconnection

The distant location hasnoisy equipment or is ina noisy environment

The One-Time Setupconfiguration isimproperly set

If the telephone had ahandset volume control,it has been set too high

The send audio volumeis set too high

Probable Remedy

See the One-TimeSetup section (Step 4,Page 9) in this manual


Redial the number orhave the distantlocation call again toget a better connection

Have the people at thedistant locationeliminate the noisesource or, if possible,move to another room


Adjust the telephonehandset volume to thenormal listening level


If you cannot resolve your difficulty by following the suggested remedies in thistroubleshooting section, please call Gentner Communications Corporation forassistance at 800-945-7730 or 801-975-7200.

Troubleshooting



TeleHybridDimensions9.80" L x 4.70" W x 1.25" H(24.89 L x 11.94 W x 3.18 H cm)Weight4 lbs. (1.81kg) dry6 lbs. (2.72kg) shippingConnectorsPHONE: 4 conductor, handset style

HANDSET: 4 conductor, handset style

CONSOLE ONLY: 8 conductor, RJ45

REC: Phono

19 VDC IN: 3 Pin, Molex style

Power Requirements120Vac, 60Hz, 23W (or optional power supply)

Echo CancellationDigital echo cancellation used to eliminatetelephone-line echo

Audio PerformanceFrequency Response300–3,300Hz, 1.5dBSignal to Noise Ratio50dBTotal Harmonic Distortion<.3 percentRecord Output-10dBu, 60 ohms, unbalanced

Operating Temperature32–100° F

Storage Temperature0–150° F

Specifications



In-line Power Supply ModuleDimensions3.5" L x 2.50" W x 2.75" H(8.90 L x 6.35 W x 7.0 H cm)Cable Length12-foot fixed cableWeight2 lbs. 1 oz. (.94 kg) dryElectricalOutput: 19Vdc unregulated, 23WInput: 120Vac, 60Hz

Supplied CablesHandset Cables16-inch flat and 32-inch flat (optional use)Connection Cable12-foot w/male and female XLRs. Input >20K;0dBu. Output 100ohms; designed to drive600ohms; 0dBm.

Gentner Communications Corporation has a varietyof systems to fit your particular communicationsneeds. If you have a large group of people, or needan installed system to accommodate a customboardroom, Gentner products are designed toprovide exceptional audio performance whileoffering the most advanced features available.

For a demonstration and more information on otherGentner telecommunications products, call yourlocal representative or a member of our sales team.

SpecificationsContinued

InstalledSystems



Gentner Communications Corporation (Manufacturer) warrants that thisproduct is free of defects in both materials and workmanship. Should any partof this equipment be defective, the Manufacturer agrees, at its option, to:

A. Repair or replace any defective part free of charge (except transportationcharges) for a period of oneyear from the date of the original purchase, provided the owner returns theequipment to the Manufacturer at the address set forth below. No charge will bemade for parts of labor during this period;

B. Furnish replacement for any defective parts in the equipment for a period ofone year from the date of originalpurchase. Replacement parts shall be furnished without charge, except laborand transportation.

This Warranty excludes assembled products not manufactured by theManufacturer whether or not they are incorporatedin a Manufacturer product or sold under a Manufacturer part or model number.

THIS WARRANTY IS VOID IF:

A. The equipment has been damaged by negligence, accident, act of God, ormishandling, or has not been operated in accordance with the proceduresdescribed in the operating and technical instructions; or,B. The equipment has been altered or repaired by other than the Manufactureror an authorized service representative of the Manufacturer; or,

C. Adaptations or accessories other than those manufactured or provided by theManufacturer have been made or attached to the equipment which, in thedetermination of the Manufacturer, shall have affected the performance, safetyor reliability of the equipment; or,

D. The equipments original serial number has been modified or removed.

NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDINGWARRANTY OF MERCHANTABILITY OR FITNESS FOR ANYPARTICULAR USE, APPLIES TO THE EQUIPMENT, nor is any person orcompany authorized to assume any warranty for the Manufacturer or any otherliability in connection with the sale of the Manufacturer's products.

Manufacturer does not assume any responsibility for consequential damages,expenses, or loss of revenue or property, inconvenience, or interruption inoperation experienced by the customer due to a malfunction in the purchasedequipment. No warranty service performed on any product shall extend theapplicable warranty period.

In case of unsatisfactory operation, the purchaser shall promptly notify theManufacturer at the address set forth below in writing, giving full particulars as

Warranty



to the defects or unsatisfactory operation. Upon receipt of such notice, theManufacturer will give instructions respecting the shipment of the equipment,or such other matters as it elects to honor this warranty as above provided. Thiswarranty does not cover damage to the equipment during shipping and theManufacturer assumes no responsibility for such damage. All shipping costsshall be paid by the customer.

This warranty extends only to the original purchaser and is not assignable ortransferable.

Gentner Communications Corporation1825 Research Way, Salt Lake City, Utah 84119

This equipment has been tested and found to comply with the limits for a ClassA digital device, pursuant to Part 15 of the FCC rules. These limits aredesigned to provide reasonable protection against harmful interference whenthe equipment is operated in a commercial environment. This equipmentgenerates, uses, and can radiate radio frequency energy and, if not installed andused in accordance with the instruction manual, may cause harmfulinterference to radio communications. Operation of this equipment in aresidential area is likely to cause harmful interference, in which case the userwill be required to correct the interference at his/her own expense.

Changes or modifications not expressly approved by Gentner CommunicationsCorporation could void the user's authority to operate the equipment.

This equipment complies with Part 68 of the FCC rules. On the bottom of theTeleHybrid is a label that contains,among other information, the FCC registration number. If requested, thisinformation must be provided to the telephone company.

If this equipment causes harm to the telephone network, the telephone companywill notify you in advance that temporary discontinuance of service may be

WarrantyContinued

FCC Part 15Compliance

FCC Part 68Compliance



required. If advance notice is not practical, the telephone company will notifythe customer as soon as possible. Also, you will be advised of your right to filea complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment,operations, or procedures that could affectthe operation of the equipment. If this happens, the telephone company willprovide advance notice for you to make the necessary modifications in order tomaintain uninterrupted service.

If trouble is experienced with this equipment, please contact GentnerCommunications Corporation at (800) 945-7730 or (801) 975-7200 for repairand warranty information. If the trouble is causing harm to the telephonenetwork, the telephone company may request you remove the equipment fromthe network until the problem is resolved.

This equipment cannot be used on telephone company provided coin service.Connection to Party Line Service is subject to state tariffs.

When the TeleHybrid is used with a leased telephone system, permission toconnect to the telephone system should be obtained from the owner of thesystem. Customer instructions for Kx-type telephones with message waitinglights and/or line status indicators must contain statements that they can onlybe connected to host equipment and never to the network. This device must beconnected through the telephone handset.

FCC Registration Number: FBIUSA-21446-KX-N

NOTICE: The Industry of Canada label identifies certified equipment. Thiscertification means that the equipment meets certain telecommunicationsnetwork protective operational and safety requirements. The Department doesnot guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, users should ensure that it is permissible to beconnected to the facilities of the local telecommunications company. Theequipment must also be installed using an acceptable method of connection. Insome cases, the company's inside wiring associated with a single line individualservice may be extended by means of a certified connector assembly (telephoneextension cord). The customer should be aware that compliance with the above

IC Compliance



conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadianmaintenance facility designated by Gentner Communications. Any repairs oralterations made by the user to this equipment, or equipment malfunctions, maygive the telecommunications company cause to request the user to disconnectthe equipment.

Users should ensure for their own protection that the electrical groundconnections of the power utility, telephone lines and internal metallic waterpipe system, if present, are connected together. This precaution may beparticularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves,but should contact the appropriate electrical inspection authority, or electrician,as appropriate.

CAUTION: For use only with certified telecommunication equipment.

ATTENTION: Pour utilisation seulement avec du materiel detelecommunications certifie de marque.

IC ComplianceContinued

SafetyInformation



TeleHybrid without built-in Mix-Minus

This model of the TeleHybrid was designedspecifically for a broadcast environment wheremix-minus capability is already availablethrough existing studio equipment. Allbroadcast versions of the TeleHybrid containAutomatic Gain Control (AGC) on the ReceiveAudio signal.

TeleHybrid to Video CODEC

TeleHybrid can be set up for conferencing, withyour Video CODEC.

Appendix A

Figure 15. TeleHybrid withoutmix-minus

Figure 16. TeleHybrid-to-videoCODEC connection



TeleHybrid to Audio Mixer in a News EditConfiguration

The TeleHybrid can be used in News Editconfiguration with audio mixer, poweredspeaker, tape recorder and headphones.

TeleHybrid use for Teleconferencing

The TeleHybrid and an Audio Teleconferencercan be connected with the XLR connectors tothe receive and send audio jacks on the back ofan Audio Teleconferencer.

Appendix AContinued

Figure 17. TeleHybrid-to-audionews-edit configuration

Figure 18. TeleHybrid set upwith an audio teleconferencer

“Our vision is to provide our customers withthe total audio solution for conferencing.”

GENTNER COMMUNICATIONS CORPORATION

Sales and Technical Assistance1825 Research Way

Salt Lake City, Utah 84119

Toll Free 800-945-7730Telephone 801-975-7200

FAX 801-977-0087FAX-On-Demand 800-695-8110

Worldwide Web Page @ http:\\www.gentner. com

Gentner Part No. 800-006-010 (Rev. 2.10)

TeleHybrid - Kilpack

Documents

Transcript of TeleHybrid - Kilpack