Technical Manual Canta 710 410 210 710-OC & 410-OC CICgto.gnresound.com › service › GNReSound...

GN ReSound asGlobal Technical Operations

gto.gnresound.comLautrupbjerg 9 • DK-2750 Ballerup • Denmark

Phone: + 45 45 75 23 16 • E-Mail: [email protected]

Technical ManualCanta 710 410 210

& 710-OC & 410-OC CIC

710-O: Marketed in the USA as ReSoundAIR AIR10

Doc. No. 0001020 rev. G

of 19

Table of contents

Subject Page

Description ..................................................................................................... 3 Typical performance data ANSI/IEC 118-7 .................................................. 4-6 Part No. lists ................................................................................................ 7-8 Diagram.......................................................................................................... 9 Programming cable ...................................................................................... 10 Microphone assembly ...................................................................................11 Receiver complete ....................................................................................... 12 Prepare the faceplate ................................................................................... 13 Hybrid connections.................................................................................. 14-15 FP fi nal assembly ......................................................................................... 16 Sizing tool..................................................................................................... 17 Tool for removing the contact module .......................................................... 18 Service tool .................................................................................................. 19

For Stepped Vent please refer to Doc. No. 0013880 for Stepped-Vent procedure.

Doc. No. 0001020 rev. G

of 19

Description

Options - all models:3 different faceplate coloursRed and blue transparent shells

Standard confi guration - all models:Size 10A batteryTransparent removal cord

Test software for Fonix system: Make sure that Fonix II Canta 5.2.0 or higher is installed as this software has all models included.Typical Battery life: Up to 84 hours

Key Features 710:• 14-band Fast-Syllabic Noise reduction.• 64 band Spectral Enhancement.• 14-band Cochlea Dynamics compression.• Adaptive Digital Feedback Suppression (DFS).• In-Situ loudness scaling.

Key Features 410:• 14-band Noise Reduction• 14-band Cochlea Dynamics compression.• Slow Adaptive Digital Feedback Suppression (DFS).• In-Situ loudness scaling.• SmartStart power-up timer.

Key Features 210:• 6-band Full Dynamic Range• Cochlea Dynamics sound processing.• Audiogram + fi tting rule.• Feedback manager

Key Features 710-OC: The ComforTecTM package:• WarpOpenTM Wide Dynamic Range Compression.• Fast acting Noise Reduction with low level expansion.• StabilizerTM DFS, Digital Feedback Suppression.• Multi-band, fast-syllabic noise reduction.• SmartStart Power up timer.• Step vent design for improved comfort.

Key Features 410-OC: The ComforTecTM package:• WarpOpenTM Wide Dynamic Range Compression.• Fast acting Noise Reduction with low level expansion.• StabilizerTM DFS, Digital Feedback Suppression.• Multi-band, fast-syllabic noise reduction.• SmartStart Power up timer.• Step vent design for improved comfort.

Doc. No. 0001020 rev. G

of 19

Typical performance data - IEC 60118-7 2cc coupler

Please note that the current drain will be 1.4 if a C 1.5 hybrid is used.

Data in accordance with IEC 118-7. All sound pressure levels (dB SPL) refer to 20 μPa. Unless otherwise is stated, data are based on a battery voltage of 1.35 V and internal impedance of 5 Ω.

Reference test frequency is 1600 Hz Tolerance UnitMax. output (90 dB SPL input) 107 ± 3 dB SPLMax. output (90 dB SPL input) at reference test frequency 103 ± 4 dB SPLFull-on gain (Input 50 dB SPL) 37 ± 5 dBFull-on gain at reference test frequency 30 ± 5 dBReference test gain 1600 Hz (Input 60 dB ) 21 ± 6 dBTypical harmonic distortion at 800 Hz

at 1600 Hz0.50.5

Max. 4Max. 4

%%

Typical equivalent input noise (Broadband method) 28 Max. 31 dB SPLBattery current 1.0 Max. 1.2 mA

Full-on Gain Parameter Settings 250 500 1000 2000 4000 6000

G[80]G[50]

2236

2236

2236

2236

2236

2234

Doc. No. 0001020 rev. G

of 19

Typical performance data (2cc coupler) - ANSI

Please note that the current drain will be 1.4 if a C 1.5 hybrid is used.

Data in accordance with ANSI S3.22-1996. All sound pressure levels (dB SPL) refer to 20 μPa. Unless otherwise is stated, data are based on a battery voltage of 1.35 V and internal impedance of 5 Ω.

Tolerance Unit

Max. output (OSPL 90) 107 ± 3 dB SPLHFA-SSPL 90 104 ± 4 dB SPLFull-on gain (Input 50 dB) 37 ± 5 dBHFA Full-on gain 32 ± 5 dBReference test gain HFA 22 ± 6 dBTypical harmonic distortion at 800 Hz at 1600 Hz

0.50.5

Max. 4Max. 4

%%

Typical equivalent input noise 28 Max. 31 dB SPLBattery current 1.0 Max. 1.2 mA

Full-on Gain Parameter Settings 250 500 1000 2000 4000 6000

G[80]G[50]

2236

2236

2236

2236

2236

2234

Doc. No. 0001020 rev. G

of 19

Typical performance data 2cc coupler

Max. output (OSPL90)

100 1000 10000

120

110

100

90

80

70

60

50

40

30

20

10

0

-10

Response gain (input 60 dB) and full-on gain (input 50 dB)

100 1000 10000

Doc. No. 0001020 rev. G

of 19

Part Lists

Item Part No. Item Part No.

Contact module, left/right 0414-409 Wire, ESW, 7x50μ, green, 16 mm 15130216Pin, hinge 0300-129 Wire, ESW, 7x50μ, red, 26 mm 15130026Contact module with hinge pin, left/right 10132501 Wire, ESW, 7x50μ, green, 26 mm 15130226Tool, contact module remover 0490-449 Coating EGC-1700 100 ml 15290401Receiver FH3375 10114401 Sizing tool kit 10159700Tubing for rec 10049101 Tube, rec, Adolf Gordon 11052-001Silicone tubing, uncut 10929-000 Insert/stud for rec. tube (100 pcs.) 10120401Microphone 9768H 2552-069 Filter red, HF3 10120201Double face tape 10038903 Filter blue, HF3 10120202Insulator for the microphone 10926-002 Wax coil 12797-000Wrap 0.9 x 3 mm 14027-001 Gauge, impression CIC 0490-479Wrap 2.2 x 3 mm 14027-003 Programming cable, right 10123001Hybrid, fl ex C 2.0 15120100 Programming cable, left 10123002Silicone tubing, uncut 11509-000 Clothing clip 10131701Resistor 56K 11662-563 Flex strip, 4 terminal 10 pcs. 10120502Wire, ESW, 7x50μ, red, 11 mm 15130011 Flex strip, 4 terminal 25 pcs. 10120503Wire, ESW, 7x50μ, amber, 14 mm 15130114 Kit, programming cable w/fl ex (R) 10127301Wire, ESW, 7x50μ, green13 mm 15130213 Kit, programming cable w/fl ex (L) 10127302Wire, ESW, 7x50μ, blue, 14 mm 15130314 Service tool/jig 10158701Wire, ESW, 7x50μ, green, 14 mm 15130214 Soldering material/tin Sn62 ø 0.32mm 1903-239Wire, ESW, 7x50μ, red, 16 mm 15130016 Soldering material/tin Sn62 ø 0.46mm 1903-249Wire, ESW, 7x50μ, amber, 16 mm 15130116 Tool for vent measuring 15178500

Doc. No. 0001020 rev. G

of 19

Part List Faceplates

Part List - Blank Faceplates - 10A

Part List - Battery Doors

Complete faceplate assembly 710, 10A



Faceplates (1 mm) - Universal Part No.Light, left/right 4036-119Medium, left/right 4036-129Dark, left/right 4036-139

Part No.Light, left/right 15126900


Battery doors - Size 10A - Universal Part No.Light, left/right 4036-019Medium, left/right 4036-029Dark, left/right 4036-039


Doc. No. 0001020 rev. G

of 19

Diagram (hybrid C 2.0 fl ex)

Doc. No. 0001020 rev. G

of 19

Programming cable

Insert the programming cable with the fl ex strip contacts away from the battery door.

Doc. No. 0001020 rev. G

of 19

Microphone assembly

Press to the bottom.

+

9768

PLACE MICINTO MODULE

SUPPORT OTHER SIDEOF FACEPLATE

Insulatorp/n 10926-0022.2 x 8.6mm.

red wirep/n 15130016.

amber wirep/n 15130116.

green wirep/n 15130216.

Place mic. into module.

+

9768 Place insulator to the black line - not with the mic casing.

Wires connected to the contact pins.

Place the double facetapep/n 100389031.56 x 7.8mm.

Gently bend the wires over the double facetape.

Place wrap over wires.

Wrapp/n 14027-0027 x 1.3mm.

Bend wrap on both sides of the mic.

-IN

Doc. No. 0001020 rev. G

of 19

Receiver complete

Wire stranded, red, 26 mm p/n 15130026

Wire stranded, green 26 mm p/n 15130226

Solder the wires as shown.

Qfl ex tubing p/n 10049-101, uncutcut to approx. 6 mm

Silicone tubing p/n 10929-000, uncutcut to 1.3mm

Place the Qfl ex tubing as shown. Bend the wires. Cut the silicone tubing to 1.3mm and place it over the wires.

BA

Doc. No. 0001020 rev. G

of 19

Prepare the faceplate

C4

Solder wires this side.

Max 1 Sec soldering time.

The electronic parts to be mounted on the faceplate.

Faceplate with contact module.Faceplate p/n:4036-119, light4036-129, medium4036-139, dark

GND

SDAVBAT

4368

CK +

Wires, stranded:Amber 14 mm SDA p/n 15130114Green 13 mm BAT GND p/n 15130213Blue 14 mm SCL p/n 15130314Green 14 mm GND p/n 15130214Red 11 mm VBAT p/n 15130011

BAT GNDSCL

Contact module complete: p/n 10132501

Doc. No. 0001020 rev. G

of 19

Hybrid connections

MIC -

MIC +

MIC IN

GND

Resistor solder points (on C 1.5 only)

Solder pointsfor jumper(on C 1.5 only)

Ver. C 1.5 fl ex p/n 10101102 Ver. C 2.0 fl ex p/n 15086100

Note: Versions C 1.5 and C 2.0 are connected the same way. It means that the new improved wires can be used on both versions.

When replacing the hybrid a resistor p/n 11662-563 56K and a solder bridge must be mounted if a ver. C 1.5 hybrid is used.

REC B REC A

SDA

SCL

BAT GND

VBAT

Danmark C2.0p/n 15120100

Doc. No. 0001020 rev. G

of 19

Hybrid connections (shown on a hybrid C 2.0)

4368

CK +

4368C K+

Before placing the wrap dip the hy-brid in EGC-1700 coating for 5 Sec. Air dry for 15 Sec. Repeat these two steps.

Place wrap 1, p/n 14027-003 and wrap 2, p/n 14027-001 - onto the hybrid.Cut silicone tube to 7mm and place it over the hybrid.Silicone tube p/n 11509-000, uncut.

Silicone tube7mm

Green wirep/n 15130214, 14mm

Green wirep/n 15130213, 13mm

Red wirep/n 15130011, 11mm

Amber wirep/n 15130114, 14mm

Blue wirep/n 15130314, 14mm

4368

CK +

Note:All wires must be handled/bent gently in order to avoid any damaging to the insulation. When connecting/soldering the wires they must be held gently with tweezers to avoid pinching and unraveling.

21

Doc. No. 0001020 rev. G

of 19

Faceplate Final Assembly

Faceplate complete Back.Faceplate complete Front.

Doc. No. 0001020 rev. G

of 19

Sizing tool

Sizing tool kit, p/n 10159700for the models CC5/181 Danalogic and Canta 710/410/210.

Doc. No. 0001020 rev. G

of 19

Tool for removing the contact module

Insert Module remover tool p/n 0490-449 as shown on the picture above.Gently press in the same direction as the arrows to release the module.

Be carefull when removing the contact module.

Doc. No. 0001020 rev. G

of 19

Service tool

The tool can be used on both sides. One side to be used for size 312 and 10, the other side to be used for size 13 only.

Only Size 13 Size 10 and 312

When working on the assembled faceplate a heat sink (p/n 10158701) must always be used in order to prevent damages to the components.

Technical Manual Canta 710 410 210 710-OC & 410-OC CICgto.gnresound.com › service › GNReSound...

Documents

Transcript of Technical Manual Canta 710 410 210 710-OC & 410-OC CICgto.gnresound.com › service › GNReSound...