TECHNICAL DATA SHEET - Midal Cable Midal Data... · Rated Breaking Load ... Calculated max. current...
Transcript of TECHNICAL DATA SHEET - Midal Cable Midal Data... · Rated Breaking Load ... Calculated max. current...
( ACCC 160 mm2 )
Nominal equivalent Aluminum Area 159,38 sq.mm
Cross Sectional Area - Aluminum 154,51 sq.mm
Cross Sectional Area - CTC Core 27,99 sq.mm
Total Area of Cross Section 182,5 sq.mm
Overall Diameter of Conductor 15,65 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 172 mm Max. single length /Drum 6020 m
Stranding configuration
No. & Diameter of CTC Core 1 x 5,97 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 3,09 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 3,17 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 2,42 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 7,49 sqmm
Composite Core Layer-2 7,88 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 17,86 x10-6 /oC below thermal knee point 75,8 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 762 Amp. AC Resistance at max. operating temp. 0,29889 Ω/ km
Calculated max. current at 120 Deg.C ^ 644 Amp. Calculated AC Resistance at 120 Deg.C 0,25816 Ω/km Geometric Mean Radius(GMR) 6,09 mm Inductive Reactance @0,3m radius at 50Hz 0,24582 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,20976 MΩ.km
General Specification Standard : ASTM B 857
69,09 kN*
0,1839 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =64 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : HELSINKI
Nil
427 kg/km
54 kg/km
Standard or Non Specular
ACCC - HelsinkiConductor Type & Code
481 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
60,4 kN
Trapezoidal Wires
0
100
200
300
400
500
600
700
800
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 165 mm2 )
Nominal equivalent Aluminum Area 165,27 sq.mm
Cross Sectional Area - Aluminum 160,22 sq.mm
Cross Sectional Area - CTC Core 18,25 sq.mm
Total Area of Cross Section 178,47 sq.mm
Overall Diameter of Conductor 15,5 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 171 mm Max. single length /Drum 5620 m
Stranding configuration
No. & Diameter of CTC Core 1 x 4,82 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 7 x 3,28 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 3,28 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 2,67 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 8,44 sqmm
Composite Core Layer-2 8,43 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,46 x10-6 /oC below thermal knee point 73,2 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 773 Amp. AC Resistance at max. operating temp. 0,28828 Ω/ km
Calculated max. current at 120 Deg.C ^ 654 Amp. Calculated AC Resistance at 120 Deg.C 0,24901 Ω/km Geometric Mean Radius(GMR) 6,04 mm Inductive Reactance @0,3m radius at 50Hz 0,24642 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,21031 MΩ.km
General Specification Standard : ASTM B 857
50,81 kN*
0,1773 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =45 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : BERN
Nil
443 kg/km
34 kg/km
Standard or Non Specular
ACCC - BernConductor Type & Code
477 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
41,8 kN
Trapezoidal Wires
0
100
200
300
400
500
600
700
800
900
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 230 mm2 )
Nominal equivalent Aluminum Area 227,61 sq.mm
Cross Sectional Area - Aluminum 220,66 sq.mm
Cross Sectional Area - CTC Core 27,99 sq.mm
Total Area of Cross Section 248,65 sq.mm
Overall Diameter of Conductor 18,29 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 201 mm Max. single length /Drum 4110 m
Stranding configuration
No. & Diameter of CTC Core 1 x 5,97 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 3,62 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 3,83 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,08 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 10,29 sqmm
Composite Core Layer-2 11,53 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,12 x10-6 /oC below thermal knee point 73,7 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 956 Amp. AC Resistance at max. operating temp. 0,20943 Ω/ km
Calculated max. current at 120 Deg.C ^ 806 Amp. Calculated AC Resistance at 120 Deg.C 0,18092 Ω/km Geometric Mean Radius(GMR) 7,12 mm Inductive Reactance @0,3m radius at 50Hz 0,23602 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,20083 MΩ.km
General Specification Standard : ASTM B 857
72,81 kN*
0,1287 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =65 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : COPENHAGEN
Nil
610 kg/km
54 kg/km
Standard or Non Specular
ACCC - CopenhagenConductor Type & Code
664 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
60,4 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 245 mm2 )
Nominal equivalent Aluminum Area 244,97 sq.mm
Cross Sectional Area - Aluminum 237,25 sq.mm
Cross Sectional Area - CTC Core 47,17 sq.mm
Total Area of Cross Section 284,42 sq.mm
Overall Diameter of Conductor 19,53 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 215 mm Max. single length /Drum 3940 m
Stranding configuration
No. & Diameter of CTC Core 1 x 7,75 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 3,85 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 3,91 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 2,95 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 11,63 sqmm
Composite Core Layer-2 12,02 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 17,49 x10-6 /oC below thermal knee point 76,4 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1012 Amp. AC Resistance at max. operating temp. 0,19496 Ω/ km
Calculated max. current at 120 Deg.C ^ 852 Amp. Calculated AC Resistance at 120 Deg.C 0,16842 Ω/km Geometric Mean Radius(GMR) 7,6 mm Inductive Reactance @0,3m radius at 50Hz 0,2319 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,19707 MΩ.km
General Specification Standard : ASTM B 857
115,15 kN*
0,1199 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =107 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : GLASGOW
Nil
656 kg/km
87 kg/km
Standard or Non Specular
ACCC - GlasgowConductor Type & Code
743 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
101,8 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 285 mm2 )
Nominal equivalent Aluminum Area 278,82 sq.mm
Cross Sectional Area - Aluminum 270,03 sq.mm
Cross Sectional Area - CTC Core 39,7 sq.mm
Total Area of Cross Section 309,74 sq.mm
Overall Diameter of Conductor 20,5 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 226 mm Max. single length /Drum 3390 m
Stranding configuration
No. & Diameter of CTC Core 1 x 7,11 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,03 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,22 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,35 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 12,78 sqmm
Composite Core Layer-2 13,98 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 18,63 x10-6 /oC below thermal knee point 74,5 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1096 Amp. AC Resistance at max. operating temp. 0,17138 Ω/ km
Calculated max. current at 120 Deg.C ^ 922 Amp. Calculated AC Resistance at 120 Deg.C 0,14808 Ω/km Geometric Mean Radius(GMR) 7,98 mm Inductive Reactance @0,3m radius at 50Hz 0,22886 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,1943 MΩ.km
General Specification Standard : ASTM B 857
100,99 kN*
0,1053 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =92 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : CASABLANCA
Nil
747 kg/km
76 kg/km
Standard or Non Specular
ACCC - CasablancaConductor Type & Code
823 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
85,8 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 325 mm2 )
Nominal equivalent Aluminum Area 319,32 sq.mm
Cross Sectional Area - Aluminum 309,56 sq.mm
Cross Sectional Area - CTC Core 39,7 sq.mm
Total Area of Cross Section 349,27 sq.mm
Overall Diameter of Conductor 21,78 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 240 mm Max. single length /Drum 2440 m
Stranding configuration
No. & Diameter of CTC Core 1 x 7,11 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 6 x 4,95 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 10 x 4,97 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,67 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 19,25 sqmm
Composite Core Layer-2 19,41 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,09 x10-6 /oC below thermal knee point 73,8 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1197 Amp. AC Resistance at max. operating temp. 0,14944 Ω/ km
Calculated max. current at 120 Deg.C ^ 1006 Amp. Calculated AC Resistance at 120 Deg.C 0,12915 Ω/km Geometric Mean Radius(GMR) 8,48 mm Inductive Reactance @0,3m radius at 50Hz 0,22505 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,19083 MΩ.km
General Specification Standard : ASTM B 857
103,21 kN*
0,0918 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =93 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : LISBON
Nil
855 kg/km
76 kg/km
Standard or Non Specular
ACCC - LisbonConductor Type & Code
931 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
85,8 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 325 mm2 )
Nominal equivalent Aluminum Area 320,54 sq.mm
Cross Sectional Area - Aluminum 310,44 sq.mm
Cross Sectional Area - CTC Core 60,27 sq.mm
Total Area of Cross Section 370,71 sq.mm
Overall Diameter of Conductor 22,4 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 246 mm Max. single length /Drum 3010 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,76 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,39 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,48 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,41 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 15,16 sqmm
Composite Core Layer-2 15,77 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 17,59 x10-6 /oC below thermal knee point 76,2 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1210 Amp. AC Resistance at max. operating temp. 0,14911 Ω/ km
Calculated max. current at 120 Deg.C ^ 1016 Amp. Calculated AC Resistance at 120 Deg.C 0,12884 Ω/km Geometric Mean Radius(GMR) 8,72 mm Inductive Reactance @0,3m radius at 50Hz 0,22329 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,18922 MΩ.km
General Specification Standard : ASTM B 857
147,56 kN*
0,0916 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =137 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : OSLO
Nil
859 kg/km
113 kg/km
Standard or Non Specular
ACCC - OsloConductor Type & Code
972 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
130,1 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 380 mm2 )
Nominal equivalent Aluminum Area 376,61 sq.mm
Cross Sectional Area - Aluminum 365,11 sq.mm
Cross Sectional Area - CTC Core 47,17 sq.mm
Total Area of Cross Section 412,28 sq.mm
Overall Diameter of Conductor 23,55 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 259 mm Max. single length /Drum 2280 m
Stranding configuration
No. & Diameter of CTC Core 1 x 7,75 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 7 x 4,98 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 11 x 5,14 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,95 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 19,5 sqmm
Composite Core Layer-2 20,78 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,07 x10-6 /oC below thermal knee point 73,8 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1333 Amp. AC Resistance at max. operating temp. 0,12681 Ω/ km
Calculated max. current at 120 Deg.C ^ 1119 Amp. Calculated AC Resistance at 120 Deg.C 0,10962 Ω/km Geometric Mean Radius(GMR) 9,17 mm Inductive Reactance @0,3m radius at 50Hz 0,22014 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,18635 MΩ.km
General Specification Standard : ASTM B 857
122,34 kN*
0,0778 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =110 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : AMSTERDAM
Nil
1009 kg/km
87 kg/km
Standard or Non Specular
ACCC - AmsterdamConductor Type & Code
1096 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
101,8 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 430 mm2 )
Nominal equivalent Aluminum Area 430,97 sq.mm
Cross Sectional Area - Aluminum 417,81 sq.mm
Cross Sectional Area - CTC Core 51,91 sq.mm
Total Area of Cross Section 469,72 sq.mm
Overall Diameter of Conductor 25,14 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 277 mm Max. single length /Drum 2130 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,13 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 7 x 5,32 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 5,28 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 4,25 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 22,21 sqmm
Composite Core Layer-2 21,86 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,19 x10-6 /oC below thermal knee point 73,6 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1457 Amp. AC Resistance at max. operating temp. 0,11093 Ω/ km
Calculated max. current at 120 Deg.C ^ 1220 Amp. Calculated AC Resistance at 120 Deg.C 0,09593 Ω/km Geometric Mean Radius(GMR) 9,79 mm Inductive Reactance @0,3m radius at 50Hz 0,21604 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,18261 MΩ.km
General Specification Standard : ASTM B 857
135,6 kN*
0,068 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =122 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : BRUSSELS
Nil
1154 kg/km
98 kg/km
Standard or Non Specular
ACCC - BrusselsConductor Type & Code
1252 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
112,1 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 470 mm2 )
Nominal equivalent Aluminum Area 472,32 sq.mm
Cross Sectional Area - Aluminum 457,89 sq.mm
Cross Sectional Area - CTC Core 60,27 sq.mm
Total Area of Cross Section 518,16 sq.mm
Overall Diameter of Conductor 26,4 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 290 mm Max. single length /Drum 2210 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,76 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 5,22 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 14 x 5,1 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 4,41 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 21,44 sqmm
Composite Core Layer-2 20,46 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,01 x10-6 /oC below thermal knee point 73,9 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1549 Amp. AC Resistance at max. operating temp. 0,10129 Ω/ km
Calculated max. current at 120 Deg.C ^ 1296 Amp. Calculated AC Resistance at 120 Deg.C 0,08761 Ω/km Geometric Mean Radius(GMR) 10,28 mm Inductive Reactance @0,3m radius at 50Hz 0,21296 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,17981 MΩ.km
General Specification Standard : ASTM B 857
155,86 kN*
0,062 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =140 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : STOCKHOLM
Nil
1265 kg/km
113 kg/km
Standard or Non Specular
ACCC - StockholmConductor Type & Code
1378 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
130,1 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
1800
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 530 mm2 )
Nominal equivalent Aluminum Area 529,05 sq.mm
Cross Sectional Area - Aluminum 510,64 sq.mm
Cross Sectional Area - CTC Core 60,27 sq.mm
Total Area of Cross Section 570,9 sq.mm
Overall Diameter of Conductor 27,72 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 305 mm Max. single length /Drum 2900 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,76 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,21 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 11 x 4,44 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 14 x 4,57 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,16 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 13,9 sqmm
Composite Core Layer-2 15,47 sqmm
Conductivity Layer-3 16,37 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,35 x10-6 /oC below thermal knee point 73,3 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1658 Amp. AC Resistance at max. operating temp. 0,09135 Ω/ km
Calculated max. current at 120 Deg.C ^ 1386 Amp. Calculated AC Resistance at 120 Deg.C 0,07905 Ω/km Geometric Mean Radius(GMR) 10,79 mm Inductive Reactance @0,3m radius at 50Hz 0,2099 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,17702 MΩ.km
General Specification Standard : ASTM B 857
158,83 kN*
0,0559 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =142 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : WARSAW
Nil
1417 kg/km
113 kg/km
Standard or Non Specular
ACCC - WarsawConductor Type & Code
1530 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
130,1 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
1800
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 540 mm2 )
Nominal equivalent Aluminum Area 534,3 sq.mm
Cross Sectional Area - Aluminum 517,97 sq.mm
Cross Sectional Area - CTC Core 71,33 sq.mm
Total Area of Cross Section 589,3 sq.mm
Overall Diameter of Conductor 28,15 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 310 mm Max. single length /Drum 1940 m
Stranding configuration
No. & Diameter of CTC Core 1 x 9,53 mm
No. of Aluminum Layers 2 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 5,57 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 14 x 5,42 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 4,66 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 24,37 sqmm
Composite Core Layer-2 23,07 sqmm
ConductivityRated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 18,86 x10-6 /oC below thermal knee point 74,1 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1682 Amp. AC Resistance at max. operating temp. 0,08965 Ω/ km
Calculated max. current at 120 Deg.C ^ 1405 Amp. Calculated AC Resistance at 120 Deg.C 0,07758 Ω/km Geometric Mean Radius(GMR) 10,96 mm Inductive Reactance @0,3m radius at 50Hz 0,20893 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,17613 MΩ.km
General Specification Standard : ASTM B 857
182,94 kN*
0,0548 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =165 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : DUBLIN
Nil
1431 kg/km
132 kg/km
Standard or Non Specular
ACCC - DublinConductor Type & Code
1563 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
153,8 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
1800
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 570 mm2 )
Nominal equivalent Aluminum Area 561,79 sq.mm
Cross Sectional Area - Aluminum 542,24 sq.mm
Cross Sectional Area - CTC Core 60,27 sq.mm
Total Area of Cross Section 602,51 sq.mm
Overall Diameter of Conductor 28,62 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 315 mm Max. single length /Drum 2710 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,76 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,31 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,38 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 14 x 4,72 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,31 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 14,59 sqmm
Composite Core Layer-2 15,06 sqmm
Conductivity Layer-3 17,48 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,53 x10-6 /oC below thermal knee point 73,1 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1726 Amp. AC Resistance at max. operating temp. 0,08611 Ω/ km
Calculated max. current at 120 Deg.C ^ 1441 Amp. Calculated AC Resistance at 120 Deg.C 0,07454 Ω/km Geometric Mean Radius(GMR) 11,14 mm Inductive Reactance @0,3m radius at 50Hz 0,20789 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,17519 MΩ.km
General Specification Standard : ASTM B 857
160,6 kN*
0,0526 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =142 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : HAMBURG
Nil
1505 kg/km
113 kg/km
Standard or Non Specular
ACCC - HamburgConductor Type & Code
1618 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
130,1 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
1800
2000
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 590 mm2 )
Nominal equivalent Aluminum Area 582,76 sq.mm
Cross Sectional Area - Aluminum 562,48 sq.mm
Cross Sectional Area - CTC Core 60,27 sq.mm
Total Area of Cross Section 622,75 sq.mm
Overall Diameter of Conductor 29,1 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 320 mm Max. single length /Drum 2980 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,76 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,38 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,46 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 4,5 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,39 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 15,04 sqmm
Composite Core Layer-2 15,62 sqmm
Conductivity Layer-3 15,92 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,63 x10-6 /oC below thermal knee point 72,9 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1767 Amp. AC Resistance at max. operating temp. 0,08307 Ω/ km
Calculated max. current at 120 Deg.C ^ 1475 Amp. Calculated AC Resistance at 120 Deg.C 0,07193 Ω/km Geometric Mean Radius(GMR) 11,33 mm Inductive Reactance @0,3m radius at 50Hz 0,20685 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,17423 MΩ.km
General Specification Standard : ASTM B 857
161,74 kN*
0,0507 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =143 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : MILAN
Nil
1561 kg/km
113 kg/km
Standard or Non Specular
ACCC - MilanConductor Type & Code
1674 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
130,1 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
1800
2000
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 610 mm2 )
Nominal equivalent Aluminum Area 605,11 sq.mm
Cross Sectional Area - Aluminum 584,05 sq.mm
Cross Sectional Area - CTC Core 71,33 sq.mm
Total Area of Cross Section 655,38 sq.mm
Overall Diameter of Conductor 29,84 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 328 mm Max. single length /Drum 2900 m
Stranding configuration
No. & Diameter of CTC Core 1 x 9,53 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 9 x 4,25 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,54 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 4,56 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,39 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 14,19 sqmm
Composite Core Layer-2 16,22 sqmm
Conductivity Layer-3 16,35 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,24 x10-6 /oC below thermal knee point 73,5 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1816 Amp. AC Resistance at max. operating temp. 0,08002 Ω/ km
Calculated max. current at 120 Deg.C ^ 1514 Amp. Calculated AC Resistance at 120 Deg.C 0,06929 Ω/km Geometric Mean Radius(GMR) 11,62 mm Inductive Reactance @0,3m radius at 50Hz 0,20527 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,1728 MΩ.km
General Specification Standard : ASTM B 857
186,66 kN*
0,0489 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =167 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : ROME
Nil
1621 kg/km
132 kg/km
Standard or Non Specular
ACCC - RomeConductor Type & Code
1753 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
153,8 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
1800
2000
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 650 mm2 )
Nominal equivalent Aluminum Area 641,75 sq.mm
Cross Sectional Area - Aluminum 619,42 sq.mm
Cross Sectional Area - CTC Core 60,27 sq.mm
Total Area of Cross Section 679,69 sq.mm
Overall Diameter of Conductor 30,41 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 335 mm Max. single length /Drum 2680 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,76 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,56 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,68 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 4,74 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,61 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 16,3 sqmm
Composite Core Layer-2 17,21 sqmm
Conductivity Layer-3 17,66 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,90 x10-6 /oC below thermal knee point 72,5 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1880 Amp. AC Resistance at max. operating temp. 0,07558 Ω/ km
Calculated max. current at 120 Deg.C ^ 1567 Amp. Calculated AC Resistance at 120 Deg.C 0,06549 Ω/km Geometric Mean Radius(GMR) 11,84 mm Inductive Reactance @0,3m radius at 50Hz 0,20408 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,17171 MΩ.km
General Specification Standard : ASTM B 857
164,95 kN*
0,0461 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =144 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : VIENNA
Nil
1719 kg/km
113 kg/km
Standard or Non Specular
ACCC - ViennaConductor Type & Code
1832 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
130,1 kN
Trapezoidal Wires
0
200
400
600
800
1000
1200
1400
1600
1800
2000
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 690 mm2 )
Nominal equivalent Aluminum Area 682,16 sq.mm
Cross Sectional Area - Aluminum 658,42 sq.mm
Cross Sectional Area - CTC Core 71,33 sq.mm
Total Area of Cross Section 729,75 sq.mm
Overall Diameter of Conductor 31,5 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 347 mm Max. single length /Drum 2550 m
Stranding configuration
No. & Diameter of CTC Core 1 x 9,53 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,74 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,83 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 4,87 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,66 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 17,64 sqmm
Composite Core Layer-2 18,29 sqmm
Conductivity Layer-3 18,61 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,60 x10-6 /oC below thermal knee point 72,9 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1960 Amp. AC Resistance at max. operating temp. 0,07116 Ω/ km
Calculated max. current at 120 Deg.C ^ 1633 Amp. Calculated AC Resistance at 120 Deg.C 0,06168 Ω/km Geometric Mean Radius(GMR) 12,27 mm Inductive Reactance @0,3m radius at 50Hz 0,20187 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,16969 MΩ.km
General Specification Standard : ASTM B 857
190,84 kN*
0,0433 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =169 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : BUDAPEST
Nil
1827 kg/km
132 kg/km
Standard or Non Specular
ACCC - BudapestConductor Type & Code
1959 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
153,8 kN
Trapezoidal Wires
0
500
1000
1500
2000
2500
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 710 mm2 )
Nominal equivalent Aluminum Area 705,75 sq.mm
Cross Sectional Area - Aluminum 681,19 sq.mm
Cross Sectional Area - CTC Core 60,27 sq.mm
Total Area of Cross Section 741,46 sq.mm
Overall Diameter of Conductor 31,77 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 349 mm Max. single length /Drum 2420 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,76 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,74 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,91 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 4,99 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,84 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 17,64 sqmm
Composite Core Layer-2 18,92 sqmm
Conductivity Layer-3 19,56 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 20,14 x10-6 /oC below thermal knee point 72,1 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 1998 Amp. AC Resistance at max. operating temp. 0,06889 Ω/ km
Calculated max. current at 120 Deg.C ^ 1664 Amp. Calculated AC Resistance at 120 Deg.C 0,05974 Ω/km Geometric Mean Radius(GMR) 12,37 mm Inductive Reactance @0,3m radius at 50Hz 0,20133 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,16921 MΩ.km
General Specification Standard : ASTM B 857
168,42 kN*
0,0419 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =145 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : PRAGUE
Nil
1891 kg/km
113 kg/km
Standard or Non Specular
ACCC - PragueConductor Type & Code
2004 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
130,1 kN
Trapezoidal Wires
0
500
1000
1500
2000
2500
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 760 mm2 )
Nominal equivalent Aluminum Area 747,91 sq.mm
Cross Sectional Area - Aluminum 721,88 sq.mm
Cross Sectional Area - CTC Core 71,33 sq.mm
Total Area of Cross Section 793,21 sq.mm
Overall Diameter of Conductor 32,85 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 361 mm Max. single length /Drum 2310 m
Stranding configuration
No. & Diameter of CTC Core 1 x 9,53 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,92 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 5,05 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 5,12 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,89 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 19,04 sqmm
Composite Core Layer-2 20,05 sqmm
Conductivity Layer-3 20,56 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,86 x10-6 /oC below thermal knee point 72,6 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 2079 Amp. AC Resistance at max. operating temp. 0,06508 Ω/ km
Calculated max. current at 120 Deg.C ^ 1729 Amp. Calculated AC Resistance at 120 Deg.C 0,05645 Ω/km Geometric Mean Radius(GMR) 12,79 mm Inductive Reactance @0,3m radius at 50Hz 0,19923 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,16729 MΩ.km
General Specification Standard : ASTM B 857
194,41 kN*
0,0395 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =170 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : MUNICH
Nil
2003 kg/km
132 kg/km
Standard or Non Specular
ACCC - MunichConductor Type & Code
2135 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
153,8 kN
Trapezoidal Wires
0
500
1000
1500
2000
2500
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 780 mm2 )
Nominal equivalent Aluminum Area 771,83 sq.mm
Cross Sectional Area - Aluminum 744,96 sq.mm
Cross Sectional Area - CTC Core 75,12 sq.mm
Total Area of Cross Section 820,09 sq.mm
Overall Diameter of Conductor 33,4 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 367 mm Max. single length /Drum 2240 m
Stranding configuration
No. & Diameter of CTC Core 1 x 9,78 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 5,01 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 5,13 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 5,19 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,94 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 19,72 sqmm
Composite Core Layer-2 20,69 sqmm
Conductivity Layer-3 21,18 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 19,80 x10-6 /oC below thermal knee point 72,6 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 2123 Amp. AC Resistance at max. operating temp. 0,06311 Ω/ km
Calculated max. current at 120 Deg.C ^ 1765 Amp. Calculated AC Resistance at 120 Deg.C 0,05476 Ω/km Geometric Mean Radius(GMR) 13,01 mm Inductive Reactance @0,3m radius at 50Hz 0,19819 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,16634 MΩ.km
General Specification Standard : ASTM B 857
204,01 kN*
0,0383 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =179 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : LONDON
Nil
2068 kg/km
142 kg/km
Standard or Non Specular
ACCC - LondonConductor Type & Code
2210 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
162,1 kN
Trapezoidal Wires
0
500
1000
1500
2000
2500
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 840 mm2 )
Nominal equivalent Aluminum Area 825,51 sq.mm
Cross Sectional Area - Aluminum 796,78 sq.mm
Cross Sectional Area - CTC Core 60,27 sq.mm
Total Area of Cross Section 857,05 sq.mm
Overall Diameter of Conductor 34,17 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 376 mm Max. single length /Drum 2140 m
Stranding configuration
No. & Diameter of CTC Core 1 x 8,76 mm
No. of Aluminum Layers 3 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 5,06 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 5,31 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 18 x 5,12 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 4,24 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 20,1 sqmm
Composite Core Layer-2 22,13 sqmm
Conductivity Layer-3 20,58 sqmm
Rated Breaking Load
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 20,51 x10-6 /oC below thermal knee point 71,6 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 2209 Amp. AC Resistance at max. operating temp. 0,0592 Ω/ km
Calculated max. current at 120 Deg.C ^ 1835 Amp. Calculated AC Resistance at 120 Deg.C 0,05143 Ω/km Geometric Mean Radius(GMR) 13,31 mm Inductive Reactance @0,3m radius at 50Hz 0,19676 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,16503 MΩ.km
General Specification Standard : ASTM B 857
174,92 kN*
0,0358 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =148 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : PARIS
Nil
2211 kg/km
113 kg/km
Standard or Non Specular
ACCC - ParisConductor Type & Code
2324 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
130,1 kN
Trapezoidal Wires
0
500
1000
1500
2000
2500
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 970 mm2 )
Nominal equivalent Aluminum Area 960,82 sq.mm
Cross Sectional Area - Aluminum 921,99 sq.mm
Cross Sectional Area - CTC Core 75,12 sq.mm
Total Area of Cross Section 997,11 sq.mm
Overall Diameter of Conductor 36,85 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 405 mm Max. single length /Drum 2870 m
Stranding configuration
No. & Diameter of CTC Core 1 x 9,78 mm
No. of Aluminum Layers 4 No
No. & equivalent Dia. of Trapezoidal wires in first layer 9 x 4,29 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,57 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 4,58 mm
No. & equivalent Dia. of Trapezoidal wires in fourth layer 20 x 4,59 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,38 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 14,46 sqmm
Composite Core Layer-2 16,42 sqmm
Conductivity Layer-3 16,5 sqmm
Rated Breaking Load Layer-4 16,54 sqmm
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 20,34 x10-6 /oC below thermal knee point 71,8 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 2425 Amp. AC Resistance at max. operating temp. 0,05173 Ω/ km
Calculated max. current at 120 Deg.C ^ 2009 Amp. Calculated AC Resistance at 120 Deg.C 0,045 Ω/km Geometric Mean Radius(GMR) 14,35 mm Inductive Reactance @0,3m radius at 50Hz 0,19201 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,16071 MΩ.km
General Specification Standard : ASTM B 857
213,97 kN*
0,0311 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =183 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : ANTWERP
Nil
2574 kg/km
142 kg/km
Standard or Non Specular
ACCC - AntwerpConductor Type & Code
2716 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
162,1 kN
Trapezoidal Wires
0
500
1000
1500
2000
2500
3000
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS
( ACCC 1050 mm2 )
Nominal equivalent Aluminum Area 1037,94 sq.mm
Cross Sectional Area - Aluminum 995,99 sq.mm
Cross Sectional Area - CTC Core 75,12 sq.mm
Total Area of Cross Section 1071,12 sq.mm
Overall Diameter of Conductor 38,2 mm
Mass per Unit length - Aluminum
Mass per Unit length - Core
Mass per unit length - Conductor
Rated Strength of the Conductor *
Maximum DC Resistance at 20oC
Lay ratio - Outer layer of Aluminum wires : Min.10 Max.13 Lay Direction of outer layer
- Inner layer of Aluminum wires : Min.10 Max.16 Surface finish
Prefered Lay of outer layer 420 mm Max. single length /Drum 2640 m
Stranding configuration
No. & Diameter of CTC Core 1 x 9,78 mm
No. of Aluminum Layers 4 No
No. & equivalent Dia. of Trapezoidal wires in first layer 8 x 4,69 mm
No. & equivalent Dia.of Trapezoidal wires in second layer 12 x 4,74 mm
No. & equivalent Dia. of Trapezoidal wires in third layer 16 x 4,77 mm
No. & equivalent Dia. of Trapezoidal wires in fourth layer 20 x 4,78 mm
Individual Aluminum wires
Minimum conductivity 63 %IACS height 3,55 mm
ASTM minimum Tensile Strength 58,6 MPa Area : Layer-1 17,3 sqmm
Composite Core Layer-2 17,68 sqmm
Conductivity Layer-3 17,87 sqmm
Rated Breaking Load Layer-4 17,98 sqmm
Coefficient of thermal expansion Modulus of elasticityabove thermal knee point 1,61 x10-6 /oC above thermal knee point 118,6 GPa
below thermal knee point 20,51 x10-6 /oC below thermal knee point 71,5 GPa
Max. allowable continuous operating temp. (surface) 175oC
Rated current at max. temperature ^ 2546 Amp. AC Resistance at max. operating temp. 0,04808 Ω/ km
Calculated max. current at 120 Deg.C ^ 2106 Amp. Calculated AC Resistance at 120 Deg.C 0,04189 Ω/km Geometric Mean Radius(GMR) 14,88 mm Inductive Reactance @0,3m radius at 50Hz 0,18975 Ω/km Capacitive Reactance @0,3m radius at 50Hz 0,15865 MΩ.km
General Specification Standard : ASTM B 857
218,13 kN*
0,0288 Ω/km
Right Hand
* Extreme Load Saftety Strength of Conductor =185 kN( Applicable if sustained load over 80% RTS expected for prolonged periods. For further information please refer to ACCC Technical note TN-750-001.)
Document version : Preliminary
Concentric Lay Stranded Trapezoidal Conductor : MADRID
Nil
2780 kg/km
142 kg/km
Standard or Non Specular
ACCC - MadridConductor Type & Code
2922 kg/km
^ Current calculated at 25 Deg.C ambient, wind velocity 0,6m/s solar radiation: 1000W/sq.m emissivity coefficient: 0,5 & absorptivity: 0,5
TECHNICAL DATA SHEET
162,1 kN
Trapezoidal Wires
0
500
1000
1500
2000
2500
3000
55 75 95 115 135 155 175Temperature oC
I max
A
Manufactured under license from
Midal Cables Ltd
ENERGY EFFICIENT HIGH CURRENT OH CONDUCTORS