TECH SUPPORT: 503.693.1918 …setting 3. door lock control box black red white 15 amp fuse brown...
Transcript of TECH SUPPORT: 503.693.1918 …setting 3. door lock control box black red white 15 amp fuse brown...
-
SOLENOID
Wiring Diagram 1 SHAVED DOORS/POWER TRUNK/SOLENOID ACTIVATION
87
87a
30
86
85
RELAY ChassisGround
(Optional 10 AWG)
BACKUPBUTTON
NEGATIVE OUTPUT FROMUltraTouch CONTROL MODULE
+ –
NOTE: To properly ground your solenoid we recommend running a 10 AWG ground wire from the solenoid bracket to the negative side of the battery.
*Not included
DIODE*
WHITE
WHITEToSensor
BLACK
BLACK
UltraTouch Control Module
TouchSensorTouch Keypad
RED
RED
Jumper Positions
(optional)
1©2012 The Hoffman Group L.L.C. All rights reserved. UltraTouch - 1 of 8 Revised 6/18/12 version 4The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
1. Mount the UltraTouch sensor in a clean, dry location. Make sure that the correct side is adhered to the surface that will be the touch-controlled area, or it will not work. The sensor will work on any non-metallic surface that is no more than one-eighth of an inch in thickness.
2. Connect the UltraTouch sensor to the control unit using the built-in connector wire.
3. Connect the black wire to your battery’s negative terminal or a good ground.
4. Connect the red wire to a positive power source. If this source requires the key to be in the ignition to be on, you will not be able to use the UltraTouch for keyless entry or shaved door applications.
5. Connect the white wire to a relay as a negative output to perform the function of your choice. The following pages contain diagrams of many popular uses.
Programming the UltraTouch™ Module is as simple as connecting pins with the supplied jumper. Next to the three-wire harness location are three sets of pins. Look at the diagram to the right for jumper locations and settings.
1. (1) 1-Second pulse output
2. Latching- continuous output between touches.
3. Output pulse for touch duration.
The UltraTouch™ touch-sensitive switch enables you to turn any non-metallic surface into a switch, activated by the mere touch of a finger! Perfect for creating a concealed, non-obvious switch to activate any power accessory. You can turn your side-view mirror into an easy way to pop your shaved door solenoids or create an invisible push-button start in the dash of your vehicle. The options are endless!
12 volts
ULTM- 15906
Programming
123
Use black jumper to connect pins.
Use jumper setting 1.
ULTRATOUCH
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
30Amp Fuse
-
ChassisGround
ChassisGround
ChassisGround
ChassisGround
ChassisGround
2©2012 The Hoffman Group L.L.C. All rights reserved. UltraTouch - 2 of 8 Revised 6/18/12 version 4The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
UltraTouch Control Module
UltraTouch Control Module
Wiring Diagram 2
Wiring Diagram 3
TouchSensor Touch
Sensor
Power Windows, Sunroof, Linear Actuators, Door LocksCONTROLLING MOTORS
DOOR LOCKS
MOTOR
UP SENSOR DOWN SENSOR
DOWN RELAY
WHITE
BLACK
RED WHITE
BLACK
RED
12 volts
87
87a
3086
8587
87a
3086
85 + –
12 VOLTS WHENBUTTON IS PUSHED
UltraTouch Control Module
TouchSensor
UNLOCK SENSOR
LOCK SENSOR
UltraTouch Control Module
TouchSensor
Use jumper setting 3.
door lock control box
BLACK
RED
WHITE
15 AMPFUSE
BROWNGREEN
GREEN
BLUE
BLUE
ACT
UAT
OR
ACT
UAT
OR
ACT
UAT
OR
ACT
UAT
OR
OPTIONAL FOR CL, CK, CA400 KITS
•BROWN
WHITE
WHITEBLACK
BLACK
RED RED
• WHITE
ULTM- 15906ULTRATOUCH
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
-
Wiring Diagram 4
3©2012 The Hoffman Group L.L.C. All rights reserved. UltraTouch - 3 of 8 Revised 6/18/12 version 4The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
white/blue
WC1000
Window Control Unit UltraTouch
Wiring Diagram 5
BrownWHITE
WHITE
WHITE
MOTORCT
Motor Control Unit
UltraTouch
Wiring Diagram 6 Wiring Diagram 7
UltraTouch
WHITE
UltraTouch
COOLING FAN
WINDOW CONTROL
MOTOR CONTROL UNIT
–87
87a
3086
85
RELAY
+
cooling fan
AIR BAGS
87
87a
3086
85
RELAY
+ –
air valve
air bag
12 volts
12 volts
Use jumper setting 1.
Use jumper setting 3.
Use jumper setting 2.
ULTM- 15906ULTRATOUCH
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
-
4©2012 The Hoffman Group L.L.C. All rights reserved. UltraTouch - 4 of 8 Revised 6/18/12 version 4The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
WHITE
UltraTouch UltraTouch
See instructions for the EC0 for further installation information.
EC0 Unit
WHITE
WHITE
UltraTouch UltraTouch
Wiring Diagram 8 Wiring Diagram 9
Wiring Diagram 10
HEADLIGHTS
BASIC ENGINE START DELUXE ENGINE START
87
87a
3086
85
RELAY
–+
WHITE
BLUESTARTERMOTOR
Low Beam Relay
Low Beam UltraTouch
High Beam Relay
High Beam UltraTouchHigh Beam
High Beam
Low Beam
87
87a
3086
8587
87a
3086
85
–+
12 volts
12 volts
Use jumper setting 2.
Use jumper setting 1.Use jumper setting 3.
ULTM- 15906ULTRATOUCH
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
-
5 ©2012 The Hoffman Group L.L.C. All rights reserved. UltraTouch - 5 of 8 Revised 6/18/12 version 4The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
with HANDS-FREE SECURITY
HF500Black #5
Basic Hands-FreeKeyless Entry
Black #2
SOLENOID
Wiring Diagram 11
87
87a
30
86
85
RELAY ChassisGround
BACKUPBUTTON
NEGATIVE OUTPUT FROMUltraTouch CONTROL MODULE
+ –
NOTE: To properly ground your solenoid we recommend running a 10 AWG ground wire from the solenoid bracket to the negative side of the battery.
*Not included
DIODE*
WHITE
BLACK
UltraTouch Control Module
TouchSensor
RED
Jumper Positions
(optional)
12 volts
Use jumper setting 1.
SHAVED DOORS/POWER TRUNK/SOLENOID ACTIVATION
When used along with the HF500, the UltraTouch is enabled when you’re near and disabled when you walk away from the vehicle for complete vehicle security.
ULTM- 15906ULTRATOUCH
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
(Optional 10 AWG)Touch Keypad
-
Wiring Diagram 13
KL550 + ULTRA1: TWO RELAYS/SEPERATE TRIGGERS
Wiring Diagram 12
KL550 + ULTRA1: ONE RELAY/SHARED TRIGGER
6©2012 The Hoffman Group L.L.C. All rights reserved. UltraTouch - 6 of 8 Revised 6/18/12 version 4The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
ULTM- 15906ULTRATOUCH
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
87
87a
30
86
85
RELAY
85
87a
86
30
87
UltraTouch Control Module
SOLENOID
BLACK
BLACK
RED
WHITE
ORANGE( PARKING LIGHTS )
SOLENOID
CB40(not included)
30A
TouchSensorTouch
Keypad
+ –
15A FUSE
RELAY
+ PARKING LIGHTS
87
87a
3086
85
OPTIONAL
87
87a
30
86
85
RELAY
UltraTouch Control Module
RED
WHITE
TouchSensorTouch
Keypad
LED
VALET SWITCH
5 c
hann
el s
yste
m
YELLOW/BLACK ( CH4 )GREEN/BLACK ( CH5 )ORANGE/BLUE - NOT USED
ORA
NG
E ( L
AM
P )
GRE
Y - N
OT
USE
D
BLA
CK -
CHA
SSIS
GRO
UN
D
YEEL
OW
ORANGE/BLACK ( CH3 )
ORANGE/GREEN - NOT USED
RED ( +12V )
CHASSISGROUND
BLUE/WHITE ( CH1 )
3A
SAFETYRELAY
CHASSIS GROUND
SWIT
CH IG
NTI
ON
PO
WER ACC
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
UltraTouch Control Module
UltraTouch Control Module
SOLENOID
BLACK
BLACK
RED
RED
WHITE
WHITE
SOLENOID
TouchSensor
TouchSensorTouch
Keypad
Touch Keypad
85
87a
86
30
87
ORANGE( PARKING LIGHTS )
CB40(not included)
+–
15A FUSE
RELAY
+ PARKING LIGHTS
87
87a
3086
85
OPTIONAL
LED
VALET SWITCH
5 c
hann
el s
yste
m
YELLOW/BLACK ( CH4 )GREEN/BLACK ( CH5 )ORANGE/BLUE - NOT USED
ORA
NG
E ( L
AM
P )
GRE
Y - N
OT
USE
D
BLA
CK -
CHA
SSIS
GRO
UN
D
YEEL
OW
ORANGE/BLACK ( CH3 )
ORANGE/GREEN - NOT USED
RED ( +12V )
CHASSISGROUND
BLUE/WHITE ( CH1 )
3A
SAFETYRELAY
CHASSIS GROUND
SWIT
CH IG
NTI
ON
PO
WER
15A
-
Wiring Diagram 15
KL800 + ULTRA1: TWO RELAYS/SEPERATE TRIGGERS
Wiring Diagram 14
KL800 + ULTRA1: ONE RELAY/SHARED TRIGGER
7©2012 The Hoffman Group L.L.C. All rights reserved. UltraTouch - 7 of 8 Revised 6/18/12 version 4The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
ULTM- 15906ULTRATOUCH
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
UltraTouch Control Module
UltraTouch Control Module
SWITCH IGNITION POWER
CHASSISGROUND
SAFETYRELAY
SOLENOID
BLACK
BLACK
BLACK
RED
RED
WHITE
WHITE
SOLENOID
CB40(not included)
TouchSensor
TouchSensorTouch
Keypad
Touch Keypad
ACC
2A FUSE
+ –
15A FUSE
RELAY + PARKING LIGHTS
87
87a
3086
85
OPTIONAL
(CH1 – 500 mA)
(CH2 – 500 mA)
(CH3 – 500 mA)
(CH4 – 500 mA)
(STARTER/IGNITION KILL OUTPUT)
RED/BLACK (CH5 – 500mA)WHITE/BLACK (CH6 – 500mA)
VALET SWITCHKL800
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
UltraTouch Control Module
SWITCH IGNITION POWER
CHASSISGROUND
SAFETYRELAY
SOLENOID
BLACK
BLACK
BLACK
RED
WHITE
SOLENOID
CB40(not included)
30A
TouchSensorTouch
Keypad
2A FUSE
+ –
15A FUSE
RELAY + PARKING LIGHTS
87
87a
3086
85
OPTIONAL
(CH1 – 500 mA)
(CH2 – 500 mA)
(CH3 – 500 mA)
(CH4 – 500 mA)
(STARTER/IGNITION KILL OUTPUT)
RED/BLACK (CH5 – 500mA)WHITE/BLACK (CH6 – 500mA)
VALET SWITCHKL800
87
87a
30
86
85
RELAY
UltraTouch Control Module
RED
WHITE
TouchSensorTouch
Keypad
-
87
87a
30
86
85
RELAY
UltraTouch Control Module
SOLENOID
BLACK
BLACK
RED
WHITE
SOLENOID
CB40(not included)
30A
TouchSensorTouch
Keypad
+ –
KEYLESSENTRY
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
87
87a
30
86
85
RELAY
UltraTouch Control Module
UltraTouch Control Module
SOLENOID
BLACK
BLACK
RED
RED
WHITE
WHITE
SOLENOID
CB40(not included)
TouchSensor
TouchSensorTouch
Keypad
Touch Keypad
+ –
KEYLESSENTRY
87
87a
30
86
85
RELAY
UltraTouch Control Module
RED
WHITE
TouchSensorTouch
Keypad
Wiring Diagram 17
KEYLESS + ULTRA1: TWO RELAYS/SEPERATE TRIGGERS
Wiring Diagram 16
KEYLESS + ULTRA1: ONE RELAY/SHARED TRIGGER
8©2012 The Hoffman Group L.L.C. All rights reserved. UltraTouch - 8 of 8 Revised 6/18/12 version 4The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the above instructions. Installation by qualified automotive professionals is highly recommended.
ULTM- 15906ULTRATOUCH
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM