TCP/IP VIDEO DOOR PHONE QUICK SETUP GUIDE

MODEL NO: PANAIP7M / PANAIP7MW / PANAIP7GM

2 3

1. Technical Specifications 4

2. Packing Contents 5

3. Name and Functions of Each Part 6

3.1 Front and Rear Part 6

4. Connection Diagram 8

4.1 System Layout 8

4.2 Wiring Diagram 9

5. Installation 10

6. Operation Description 12

6.1 Main Page 12

7. Quick setup 14

71 Enter setup page 14

7.2 Set Encoder and Unit ID 14

7.3 Set Unlock Password 15

7.4 Wi-Fi Settings Only for PANAIP7MW monitor 16

8. User Manual 17

Please follow these instructions to prevent any personal danger or property loss.

Warning: To avoid death or serious injury

Do not disassemble, install, or repair this product on your own accord

Do not place the product near a hot or humid place

Do not forcibly bend the cord or put a heavy object on the product

Do not use water, thinner or a detergent for removing oil products when cleaning the exterior

Do not connect to other products while in use

Make sure to clean with a dry cloth to prevent any breakdown or electric shock

If the product emits a peculiar noise, odour or smoke, immediately disconnect the power, and then contact PSA Products.

Do not insert the power plug into a 240VAC mains socket with a wet hand

Caution: To avoid personal injury or property loss

Ensure that dust or foreign substances do not collect on the product

Ensure foreign substances do not enter the product

Avoid direct sunlight or heat upon the device

Install the product on a flat & stable location

Unplug the product from AC Mains power if it would not be used for a long time

Do not unplug the micro SD card while recording, as this may cause loss of data

TABLE OF CONTENTS WARNING AND CAUTION

4 5

• 7” capacitive touch screen monitor. Resolution: 800*480 pixels

• Zone alarms (4-zones max.)

• Supports up to 19 door panels

• Video Encoding: H.264

• Network Connection: Ethernet (POE)

• Operating Voltage: 18V (POE)

• Operating Current: 300 mA (max: 500 mA, stand-by: 180mA)

• Operation Temperature: -10~55ºC

• Operating system: Linux

• Internal Flash Memory (Internal storage: 100 pictures)

• Micro SD-Card Slot (Micro SD-card not included with Monitor)

• Dimensions(mm): Indoor monitor: 210(W) x 140(H) x 20(D) Guard unit: 326(W) x 206(H) x 56(D)

Indoor monitor (PANAIP7M excludes 4 pin wiring cable)

Main Body Wall bracket 2 pin wiring cable DC connector Quick start guide

KA M4*35mm Mounting screw

M4*35mm plastic expansion pipe

8 pin wiring cable 4 pin wiring cable

Guard unit

Main Body Handset DC connector Helical line

KM M3*5mm Mounting screw

Left bracket Right bracket Quick start guide

1. TECHNICAL SPECIFICATIONS 2. PACKING CONTENTS

6 7

3.1 FRONT AND REAR PART

Indoor monitor (Model No: PANAIP7M & PANAIP7MW)

NO. Part Name

1 Power Indicator White LED when power on

2 Message Indicator White LED flashes when have unread message/call

3 Alarm Indicator White LED flashes when have alarm

4 Screen 7-inch digital TFT LCD

5 Microphone Receive voice from the user

6 Micro SD Card Slot Socket for micro SD card

7 Connection Port Interface for sensor

8 Connection Port Interface for doorbell

9 DC Power 15~20 VDC (1A) power supply

10 RJ45 Connector Interface for RJ45

11 Video Input Interface for Video door bell (Not supported in PANAIP7M)

12 Speaker

Guard unit (Model No: PANAIP7GM)

NO. Part Name

1 Handset

2 RJ11 Connector Connection for helical handset cable

3 Power Indicator Red LED when power on

4 Screen 7-inch digital TFT LCD

5 Speaker Receive voice from the user

6 Door Release Button Press button to release door lock

7 RJ45 Connector Interface for RJ45

8 DC Power 12~20 VDC (1A) power supply

3. NAME AND FUNCTIONS OF EACH PART

8 9

4.1 SYSTEM LAYOUT

Remark:

• The distance between the PoE Switch and other devices (indoor monitor, door panel, network switch, guard unit) must not exceed 70 meters.

• The system supports up to 98 buildings, and a maximum of 32 IP cameras.

• Each room supports up to 3 monitors.

• The address of the other devices can only be set after first configuring the address of the 1st Building Panel (to either 5-Digit:01-801, or 6-Digit:01-9001).

4.2 WIRING DIAGRAM

is the interface socket for alarm sensors, and is located at the back of the Monitor. Alarm sensors for four alarm zones can be connected to these ALM1, ALM2, ALM3, and ALM4 terminals.

4. CONNECTION DIAGRAM

10 11

INDOOR MONITORStandard installation height of door panel puts the lens about 1550mm above the floor. Hence, the centre of the camera should be about 1540mm above ground level.

1650

1540

1550

Monitor Installation Location

Install the Monitor about 1500mm from floor level so that the centre of the screen is at eye level. This means the centre of the metal wall bracket is 1450mm from floor level.

Installing the Indoor Monitor

1) Remove mounting bracket from behind monitor and fix it onto the wall with screws.

2) Install the cable and connect the system according to the wiring diagrams in Section 4.

3) Hang the monitor onto the mounting bracket.

GUARD UNIT

Installing the Guard Unit

1) Place the guard unit on a level desktop;

2) Fix the bracket to the rear of the monitor with screws.

3) Install the cable and connect the system according to the wiring diagrams in Section 4.

5. INSTALLATION

12 13

The illustrations in this section are based on Model Nos. PANAIP7MW and PANAIP7GM.

6.1 MAIN SCREEN

Touch the screen anywhere in standby mode, the Main Page will be displayed:

ICON DEFINITION

The following table shows each icon on the Main Page and its function.

Enter the call menu Enter the message menu

Enter the monitor menu Alarm management

Picture storage Enter the setting menu

No network indicator [Do Not Disturb] mode indicator

WIFI connection1 Emergency Call (to Guard)

Alarm Mode: Set the monitor for Leaving or Presence mode

(Default Password: 9999)

1 Not available for Model Number PANAIP7M.

• The Guard unit does not have the two icons for Emergency Call and Alarm mode.

6. OPERATION DESCRIPTION

14 15

7. QUICK SETUP

Please setup Door Panel before proceeding to the next step.

7.1 ENTER SETUP PAGE

Select “Setting”

7.2 SET ENCODER AND UNIT ID

Select “Engineering Setting”

Enter Engineering Password (Default: 0000)

Select “Device Information”

Select “5 digits Encoding” if door station is set to 5 digits Encoding.

For 6 digits Encoding refer to monitor manual.

Enter Building Number: 1Enter Room/Unit number: ___

Enter Ext. No: ___ (1st monitor always 1)

Select to complete.

Monitor will restart.

7.3 SET UNLOCK PASSWORD

The password must be 4 digits and cannot be identical digits (e.g. not ‘3333’ nor ‘8888’ or consecutive numbers (e.g. not ‘1234’ nor ‘4567’).

Enter the Setup page: Select “Setting”

Select Unlock Password

Enter a 4-digit Password

Enter confirm Password.

Touch blue screen to hide keypad

Select to save the information.

Select to exit

16 17

7. QUICK SETUP 8. USER MANUAL

7.4 WI-FI SETTINGS ONLY FOR PANAIP7MW MONITOR

Select Wi-Fi

Select Wi-Fi config

Select your Wi-Fi on screen and enter Wi-Fi password.

Call forward selection:

Off - Stop all call forwarding

Immediate - Forward call to phone app.

Timeout - Forward call when call has not been answered by monitor.

Press to return to setting

Press to return to main screen.

To download User Manual, go to: www.psaproducts.com.au

17 Millicent Street, Burwood, VIC 3125 AustraliaTel: 1300 PSA PRODUCTS (1300 772 776)Fax: (03) 9888 9993enquiry@psaproducts.com.au psaproducts.com.au